Abstract: By textile science incorporating with electronic
industry, developed textile products start to take part in different
areas such as industry, military, space, medical etc. for health,
protection, defense, communication and automation. Electronic
textiles (e-textiles) are fabrics that contain electronics and
interconnections with them. In this study, two types of base yarns
(cotton and acrylic) and three types of conductive steel yarns with
different linear resistance values (14Ω/m, 30Ω/m, 70Ω/m) were used
to investigate the effect of base yarn type and linear resistance of
conductive yarns on thermal behavior of e-textile structures. Thermal
behavior of samples was examined by thermal camera.
Abstract: The thermal behavior of a large-scale, phase change material (PCM) enhanced building envelope system was studied in regard to the need for pre-fabricated construction in subtropical regions. The proposed large-scale envelope consists of a reinforced aluminum skin, insulation core, phase change material and reinforced gypsum board. The PCM impact on an energy efficiency of an enveloped room was resolved by validation of the EnergyPlus numerical scheme and optimization of a smart material location in the core. The PCM location was optimized by a minimization method of a cooling energy demand. It has been shown that there is good agreement between the test and simulation results. The optimal location of the PCM layer in Hong Kong summer conditions has been then recomputed for core thicknesses of 40, 60 and 80 mm. A non-dimensional value of the optimal PCM location was obtained to be same for all the studied cases and the considered external and internal conditions.
Abstract: Magnetic powder of Sr-ferrite was prepared by
conventional and sol-gel auto-combustion methods. In conventional
method, strontium carbonate and ferric oxide powders were mixed
together and then mixture was calcined. In sol-gel auto-combustion
method, a solution containing strontium nitrate, ferric nitrate and
citric acid was heated until the combustion took place automatically;
then, as-burnt powder was calcined. Thermal behavior, phase
identification, morphology and magnetic properties of powders
obtained by these two methods were compared by DTA, XRD, SEM
and VSM techniques. According to the results of DTA analysis,
formation temperature of Sr-ferrite obtained by conventional and solgel
auto-combustion methods were 1300°C and 1000°C, respectively.
XRD results confirmed the formation of pure Sr-ferrite at the
mentioned temperatures. Plate and hexagonal-shape particles of Srferrite
were observed using SEM. The Sr-ferrite powder obtained by
sol-gel auto-combustion method had saturation magnetization of
66.03 emu/g and coercivity of 5731 Oe in comparison with values of
58.20 emu/g and 4378 Oe obtained by conventional method.
Abstract: Thermal insulation materials based on natural fibers
represent a very promising area of materials based on natural easy
renewable row sources. These materials may be in terms of the
properties of most competing synthetic insulations, but show
somewhat higher moisture sensitivity and thermal insulation
properties are strongly influenced by the density and orientation of
fibers. The paper described the problem of hygrothermal behavior of
thermal insulation materials based on natural plant and animal fibers.
This is especially the dependence of the thermal properties of these
materials on the type of fiber, bulk density, temperature, moisture and
the fiber orientation.
Abstract: A mathematical heat transfer model for the prediction of transient heating of the slab in a direct-fired walking beam type reheating furnace has been developed by considering the nongray thermal radiation with given furnace environments. The furnace is modeled as radiating nongray medium with carbon dioxide and water with five-zoned gas temperature and the furnace wall is considered as a constant temperature lower than furnace gas one. The slabs are moving with constant velocity depending on the residence time through the non-firing, charging, preheating, heating, and final soaking zones. Radiative heat flux obtained by considering the radiative heat exchange inside the furnace as well as convective one from the surrounding hot gases are introduced as boundary condition of the transient heat conduction within the slab. After validating thermal radiation model adopted in this work, thermal fields in both model and real reheating furnace are investigated in terms of radiative heat flux in the furnace and temperature inside the slab. The results show that the slab in the furnace can be more heated with higher slab emissivity and residence time.
Abstract: A one-dimensional mathematical model was developed in order to analyze and optimize the latent heat storage wall. The governing equations for energy transport were developed by using the enthalpy method and discretized with volume control scheme. The resulting algebraic equations were next solved iteratively by using TDMA algorithm. A series of numerical investigations were conducted in order to examine the effects of the thickness of the PCM layer on the thermal behavior of the proposed heating system. Results are obtained for thermal gain and temperature fluctuation. The charging discharging process was also presented and analyzed.
Abstract: Laminar mixed Convection heat transfer of a nanofluid with prescribed constant heat flux on the inner wall of horizontal annular tube has been studied numerically based on two-phase mixture model in different Rayleigh Numbers and Azimuth angles. Effects of applying of different volume fractions of Al2O3 nanoparticles in water as a base fluid on hydrodynamic and thermal behaviors of the fluid flow such as axial velocity, secondary flow, temperature, heat transfer coefficient and friction coefficient at the inner and outer wall region, has been investigated. Conservation equations in elliptical form has been utilized and solved in three dimensions for a steady flow. It is observed that, there is a good agreement between results in this work and previously published experimental and numerical works on mixed convection in horizontal annulus. These particles cause to increase convection heat transfer coefficient of the fluid, meanwhile there is no considerable effect on friction coefficient.
Abstract: The Proton Exchange Membranes (PEM) are largely studied because they operate at low temperatures and they are suitable for mobile applications. However, there are some deficiencies in their operation, mainly those that use ethanol as a hydrogen source, that require a certain attention. Therefore, this research aimed to develop Nafion® composite membranes, mixing clay minerals, kaolin and halloysite to the polymer matrix in order to improve the ethanol molecule retentions and, at the same time, to keep the system’s protonic conductivity. The modified Nafion/Kaolin, Nafion/Halloysite composite membranes were prepared in weight proportion of 0.5, 1.0 and 1.5. The membranes obtained were characterized as to their ethanol permeability, protonic conductivity and water absorption. The composite morphology and structure are characterized by SEM and EDX and the thermal behavior is determined by TGA and DSC. The analysis of the results shows ethanol permeability reduction from 48% to 63%. However, the protonic conductivity results are lower in relation to pure Nafion®. As to the thermal behavior, the Nafion® composite membranes were stable up to a temperature of 325ºC.
Abstract: LTCC (Low Temperature Co-fired Ceramics) being the most advantageous technology towards the multilayer substrates for various applications, demands an extensive study of its raw materials. In the present work, a series of CuxMg1-xNb2O6 (x=0,0.4,0.6,1) has been prepared using sol-gel synthesis route and sintered at a temperature of 900°C to study its applicability for LTCC technology as the firing temperature is 900°C in this technology. The phase formation has been confirmed using X-ray Diffraction. Thermal properties like thermal conductivity and thermal expansion being very important aspect as the former defines the heat flow to avoid thermal instability in layers and the later provides the dimensional congruency of the dielectric material and the conductors, are studied here over high temperature up to the firing temperature. Although the values are quite satisfactory from substrate requirement point view, results have shown anomaly over temperature. The anomalous thermal behavior has been further analyzed using TG-DTA.
Abstract: The periodic mixed convection of a water-copper
nanofluid inside a rectangular cavity with aspect ratio of 3 is
investigated numerically. The temperature of the bottom wall of the
cavity is assumed greater than the temperature of the top lid which
oscillates horizontally with the velocity defined as u = u0 sin (ω t).
The effects of Richardson number, Ri, and volume fraction of
nanoparticles on the flow and thermal behavior of the nanofluid are
investigated. Velocity and temperature profiles, streamlines and
isotherms are presented. It is observed that when Ri < 1, heat transfer
rate is much greater than when Ri > 1. The higher value of Ri
corresponds to a lower value of the amplitude of the oscillation of
Num in the steady periodic state. Moreover, increasing the volume
fraction of the nanoparticles increases the heat transfer rate.
Abstract: The hydrothermal behavior of a bed consisting of
magnetic and shale oil particle admixtures under the effect of a
transverse magnetic field is investigated. The phase diagram, bed
void fraction are studied under wide range of the operating
conditions i.e., gas velocity, magnetic field intensity and fraction of
the magnetic particles. It is found that the range of the stabilized
regime is reduced as the magnetic fraction decreases. In addition, the
bed voidage at the onset of fluidization decreases as the magnetic
fraction decreases. On the other hand, Nusselt number and
consequently the heat transfer coefficient is found to increase as the
magnetic fraction decreases. An empirical equation is investigated to
relate the effect of the gas velocity, magnetic field intensity and
fraction of the magnetic particles on the heat transfer behavior in the
bed.
Abstract: In this work, the effects of scale on thermal behavior of the slab in a walking-beam type reheating furnace is studied by considering scale formation and growth in a furnace environment. Also, mathematical heat transfer model to predict the thermal radiation in a complex shaped reheating furnace with slab and skid buttons is developed with combined nongray WSGGM and blocked-off solution procedure. The model can attack the heat flux distribution within the furnace and the temperature distribution in the slab throughout the reheating furnace process by considering the heat exchange between the slab and its surroundings, including the radiant heat transfer among the slabs, the skids, the hot combustion gases and the furnace wall as well as the gas convective heat transfer in the furnace. With the introduction of the mathematical formulations validation of the present numerical model is conducted by calculating two example problems of blocked-off and nongray gas radiative heat transfer. After discussing the formation and growth of the scale on the slab surface, slab heating characteristics with scale is investigated in terms of temperature rise with time.
Abstract: This paper studies the optimum design for reducing
optical loss of an 8x8 mechanical type optical switch due to the
temperature change. The 8x8 optical switch is composed of a base, 8
input fibers, 8 output fibers, 3 fixed mirrors and 17 movable mirrors.
First, an innovative switch configuration is proposed with
thermal-compensated design. Most mechanical type optical switches
have a disadvantage that their precision and accuracy are influenced
by the ambient temperature. Therefore, the thermal-compensated
design is to deal with this situation by using materials with different
thermal expansion coefficients (α). Second, a parametric modeling
program is developed to generate solid models for finite element
analysis, and the thermal and structural behaviors of the switch are
analyzed. Finally, an integrated optimum design program, combining
Autodesk Inventor Professional software, finite element analysis
software, and genetic algorithms, is developed for improving the
thermal behaviors that the optical loss of the switch is reduced. By
changing design parameters of the switch in the integrated design
program, the final optimum design that satisfies the design constraints
and specifications can be found.
Abstract: Among the various cooling processes in industrial
applications such as: electronic devices, heat exchangers, gas
turbines, etc. Gas turbine blades cooling is the most challenging one.
One of the most common practices is using ribbed wall because of
the boundary layer excitation and therefore making the ultimate
cooling. Vortex formation between rib and channel wall will result in
a complicated behavior of flow regime. At the other hand, selecting
the most efficient method for capturing the best results comparing to
experimental works would be a fascinating issue. In this paper 4
common methods in turbulence modeling: standard k-e, rationalized
k-e with enhanced wall boundary layer treatment, k-w and RSM
(Reynolds stress model) are employed to a square ribbed channel to
investigate the separation and thermal behavior of the flow in the
channel. Finally all results from different methods which are used in
this paper will be compared with experimental data available in
literature to ensure the numerical method accuracy.
Abstract: wind catchers have been served as a cooling system, used to provide acceptable ventilation by means of renewable energy of wind. In the present study, the city of Yazd in arid climate is selected as case study. From the architecture point of view, learning about wind catchers in this study is done by means of field surveys. Research method for selection of the case is based on random form, and analytical method. Wind catcher typology and knowledge of relationship governing the wind catcher's architecture were those measures that are taken for the first time. 53 wind catchers were analyzed. The typology of the wind-catchers is done by the physical analyzing, patterns and common concepts as incorporated in them. How the architecture of wind catcher can influence their operations by analyzing thermal behavior are the archetypes of selected wind catchers. Calculating fluids dynamics science, fluent software and numerical analysis are used in this study as the most accurate analytical approach. The results obtained from these analyses show the formal specifications of wind catchers with optimum operation in Yazd. The knowledge obtained from the optimum model could be used for design and construction of wind catchers with more improved operation
Abstract: Rarefied gas flows are often occurred in micro electro
mechanical systems and classical CFD could not precisely anticipate
the flow and thermal behavior due to the high Knudsen number.
Therefore, the heat transfer and the fluid dynamics characteristics of
rarefied gas flows in both a two-dimensional simple microchannel
and geometry similar to single Knudsen compressor have been
investigated with a goal of increasing performance of a actual
Knudsen compressor by using a particle simulation method. Thermal
transpiration and thermal creep, which are rarefied gas dynamic
phenomena, that cause movement of the flow from less to higher
temperature is generated by using two different longitude temperature
gradients (Linear, Step) along the walls of the flow microchannel. In
this study the influence of amount of temperature gradient and
governing pressure in various Knudsen numbers and length-to-height
ratios have been examined.
Abstract: Thermal behavior of fuel channel under loss of coolant accident (LOCA) is a major concern for nuclear reactor safety. LOCA along with failure of emergency cooling water system (ECC) may leads to mechanical deformations like sagging and ballooning. In order to understand the phenomenon an experiment has been carried out using 19 pin fuel element simulator. Main purpose of the experiment was to trace temperature profiles over the pressure tube, calandria tube and clad tubes of Indian Pressurized Heavy Water Reactor (IPHWR) under symmetrical and asymmetrical heat-up conditions. For simulating the fully voided scenario, symmetrical heating of pressure was carried out by injecting 13.2 KW (2 % of nominal power) to all the 19 pins and the temperatures of pressure tube, calandria tube and clad tubes were measured. During symmetrical heating the sagging of fuel channel was initiated at 460 °C and the highest temperature attained by PT was 650 °C . The decay heat from clad tubes was dissipated to moderator mainly by radiation and natural convection. The highest temperature of 680 °C was observed over the outer ring of clad tubes of fuel simulator. Again, to simulate partially voided condition, asymmetrical heating of pressure was carried out by supplying 8.0 kW power to upper 8 pins of fuel simulator and temperature profiles were measured. Along the circumference of pressure tube (PT) the highest temperature difference of 320 °C was observed, which highlights the magnitude of thermal stresses under partially voided conditions.
Abstract: The objectif of the present work is to determinate the
potential of the solar parabolic trough collector (PTC) for use in the
design of a solar thermal power plant in Algeria. The study is based
on a mathematical modeling of the PTC. Heat balance has been
established respectively on the heat transfer fluid (HTF), the absorber
tube and the glass envelop using the principle of energy conservation
at each surface of the HCE cross-sectionn. The modified Euler
method is used to solve the obtained differential equations. At first
the results for typical days of two seasons the thermal behavior of the
HTF, the absorber and the envelope are obtained. Then to determine
the thermal performances of the heat transfer fluid, different oils are
considered and their temperature and heat gain evolutions compared.
Abstract: A transient heat transfer mathematical model for the
prediction of temperature distribution in the car body during primer
baking has been developed by considering the thermal radiation and
convection in the furnace chamber and transient heat conduction
governing equations in the car framework. The car cockpit is
considered like a structure with six flat plates, four vertical plates
representing the car doors and the rear and front panels. The other
two flat plates are the car roof and floor. The transient heat
conduction in each flat plate is modeled by the lumped capacitance
method. Comparison with the experimental data shows that the heat
transfer model works well for the prediction of thermal behavior of
the car body in the curing furnace, with deviations below 5%.
Abstract: A new and novel approach in medicine is the use of
cold plasma for various applications such as sterilization blood
coagulation and cancer cell treatment. In this paper a pin-to-hole
plasma jet suitable for biological applications is investigated and
characterized and the possibility and feasibility of cancer cell
treatment is evaluated. The characterization includes power
consumption via Lissajous method, thermal behavior of plasma using
Infra-red camera as a novel method, Optical Emission Spectroscopy
(OES) to determine the species that are generated. Treatment of
leukemia cancer cells is also implemented and MTT assay is used to
evaluate viability.