Abstract: In this paper, we have proposed two novel plasmonic demultiplexing structures based on metal-insulator-metal surfaces which, beside their compact size, have a very good transmission spectrum. The impact of the key internal parameters on the transmission spectrum is numerically analyzed by using the twodimensional (2D) finite difference time domain (FDTD) method. The proposed structures could be used to develop ultra-compact photonic wavelength demultiplexing devices for large-scale photonic integration.
Abstract: In this paper effect of stator slots structure and
switching angle on a cylindrical single-phase brushless direct current
motor (BLDC) is analyzed. BLDC motor with three different
structures for stator slots is designed by using RMxprt software and
efficiency of BLDC motor for different structures in full-load
condition has been presented. Then the BLDC motor in different
conditions by using Maxwell 3D software is designed and with finite
element method is analyzed electromagnetically. At the end with the
use of MATLAB software influence of switching angle on motor
performance investigated and optimal angle has been determined.
The results indicate that with correct choosing of stator slots structure
and switching angle, maximum efficiency can be found.
Abstract: The dynamic spectrum allocation solutions such as
cognitive radio networks have been proposed as a key technology to
exploit the frequency segments that are spectrally underutilized.
Cognitive radio users work as secondary users who need to
constantly and rapidly sense the presence of primary users or
licensees to utilize their frequency bands if they are inactive. Short
sensing cycles should be run by the secondary users to achieve
higher throughput rates as well as to provide low level of interference
to the primary users by immediately vacating their channels once
they have been detected. In this paper, the throughput-sensing time
relationship in local and cooperative spectrum sensing has been
investigated under two distinct scenarios, namely, constant primary
user protection (CPUP) and constant secondary user spectrum
usability (CSUSU) scenarios. The simulation results show that the
design of sensing slot duration is very critical and depends on the
number of cooperating users under CPUP scenario whereas under
CSUSU, cooperating more users has no effect if the sensing time
used exceeds 5% of the total frame duration.
Abstract: techniques are examined to overcome the
performance degradation caused by the channel dispersion using
slow frequency hopping (SFH) with dynamic frequency hopping
(DFH) pattern adaptation. In DFH systems, the frequency slots are
selected by continuous quality monitoring of all frequencies available
in a system and modification of hopping patterns for each individual
link based on replacing slots which its signal to interference ratio
(SIR) measurement is below a required threshold. Simulation results
will show the improvements in BER obtained by DFH in comparison
with matched frequency hopping (MFH), random frequency hopping
(RFH) and multi-carrier code division multiple access (MC-CDMA)
in multipath slowly fading dispersive channels using a generalized
bandpass two-path transfer function model, and will show the
improvement obtained according to the threshold selection.
Abstract: New generation mobile communication networks have
the ability of supporting triple play. In order that, Orthogonal
Frequency Division Multiplexing (OFDM) access techniques have
been chosen to enlarge the system ability for high data rates
networks. Many of cross-layer modeling and optimization schemes
for Quality of Service (QoS) and capacity of downlink multiuser
OFDM system were proposed. In this paper, the Maximum Weighted
Capacity (MWC) based resource allocation at the Physical (PHY)
layer is used. This resource allocation scheme provides a much better
QoS than the previous resource allocation schemes, while
maintaining the highest or nearly highest capacity and costing similar
complexity. In addition, the Delay Satisfaction (DS) scheduling at the
Medium Access Control (MAC) layer, which allows more than one
connection to be served in each slot is used. This scheduling
technique is more efficient than conventional scheduling to
investigate both of the number of users as well as the number of
subcarriers against system capacity. The system will be optimized for
different operational environments: the outdoor deployment scenarios
as well as the indoor deployment scenarios are investigated and also
for different channel models. In addition, effective capacity approach
[1] is used not only for providing QoS for different mobile users, but
also to increase the total wireless network's throughput.
Abstract: This paper presents the optimum design for a double
stator, cup rotor machine; a novel type of BLDC PM Machine. The optimization approach is divided into two stages: the first stage is
calculating the machine configuration using Matlab, and the second stage is the optimization of the machine using Finite Element
Modeling (FEM). Under the design specifications, the machine
model will be selected from three pole numbers, namely, 8, 10 and 12 with an appropriate slot number. A double stator brushless DC
permanent magnet machine is designed to achieve low cogging torque; high electromagnetic torque and low ripple torque.
Abstract: Numerical simulations are performed for laminar
continuous and pulsed jets impinging on a surface in order to
investigate the effects of pulsing frequency on the heat transfer
characteristics. The time-averaged Nusselt number of pulsed jets is
larger in the impinging jet region as compared to the continuous jet,
while it is smaller in the outer wall jet region. At the stagnation point,
the mean and RMS Nusselt numbers become larger and smaller,
respectively, as the pulsing frequency increases. Unsteady behaviors
of vortical fluid motions and temperature field are also investigated to
understand the underlying mechanisms of heat transfer enhancement.
Abstract: In this paper, a tooth shape optimization method for
cogging torque reduction in Permanent Magnet (PM) motors is
developed by using the Reduced Basis Technique (RBT) coupled by
Finite Element Analysis (FEA) and Design of Experiments (DOE)
methods. The primary objective of the method is to reduce the
enormous number of design variables required to define the tooth
shape. RBT is a weighted combination of several basis shapes. The
aim of the method is to find the best combination using the weights
for each tooth shape as the design variables. A multi-level design
process is developed to find suitable basis shapes or trial shapes at
each level that can be used in the reduced basis technique. Each level
is treated as a separated optimization problem until the required
objective – minimum cogging torque – is achieved. The process is
started with geometrically simple basis shapes that are defined by
their shape co-ordinates. The experimental design of Taguchi method
is used to build the approximation model and to perform
optimization. This method is demonstrated on the tooth shape
optimization of a 8-poles/12-slots PM motor.
Abstract: Cooktop burners are widely used nowadays. In
cooktop burner design, nozzle efficiency and greenhouse
gas(GHG) emissions mainly depend on heat transfer from the
premixed flame to the impinging surface. This is a complicated
issue depending on the individual and combined effects of various
input combustion variables. Optimal operating conditions for
sustainable burner design were rarely addressed, especially in the
case of multiple slot-jet burners. Through evaluating the optimal
combination of combustion conditions for a premixed slot-jet
array, this paper develops a practical approach for the sustainable
design of gas cooktop burners. Efficiency, CO and NOx emissions
in respect of an array of slot jets using premixed flames were
analysed. Response surface experimental design were applied to
three controllable factors of the combustion process, viz.
Reynolds number, equivalence ratio and jet-to-vessel distance.
Desirability Function Approach(DFA) is the analytic technique
used for the simultaneous optimization of the efficiency and
emission responses.
Abstract: We consider a two-way relay network where two sources exchange information. A relay helps the two sources exchange information using the decode-and-XOR-forward protocol. We investigate the power minimization problem with minimum rate constraints. The system needs two time slots and in each time slot the required rate pair should be achievable. The power consumption is minimized in each time slot and we obtained the closed form solution. The simulation results confirm that the proposed power allocation scheme consumes lower total power than the conventional schemes.
Abstract: Space-time block code(STBC) has been studied to get
full diversity and full rate in multiple input multiple output(MIMO)
system. Achieving full rate is difficult in cooperative communications
due to the each user consumes the time slots for transmitting
information in cooperation phase. So combining MIMO systems
with cooperative communications has been researched for full diversity
and full rate. In orthogonal frequency division multiple access
(OFDMA) system, it is an alternative way that each user shares their
allocated subchannels instead of using the MIMO system to improve
the transmission rate. In this paper, a Decode-and-forward (DF)
based cooperative communication scheme is proposed. The proposed
scheme has improved transmission rate and reliability in multi-path
fading channel of the OFDMA up-link condition by modified STBC
structure and subchannel sharing.
Abstract: Current spectrums of a high power induction machine was calculated for the cases of full symmetry, static and dynamic eccentricity. The calculations involve integration of 93 electrical plus four mechanical ordinary differential equations. Electrical equations account for variable inductances affected by slotting and eccentricities. The calculations were followed by Fourier analysis of the stator currents in steady state operation. The paper presents the stator current spectrums in full symmetry, static and dynamic eccentricity cases, and demonstrates the harmonics present in each case. The effect of dynamic eccentricity is demonstrating via comparing the current spectrums related to dynamic eccentricity cases with the full symmetry one. The paper includes one case study, refers to dynamic eccentricity, to present the spectrum of the measured current and demonstrate the existence of the harmonics related to dynamic eccentricity. The zooms of current spectrums around the main slot harmonic zone are included to simplify the comparison and prove the existence of the dynamic eccentricity harmonics in both calculated and measured current spectrums.
Abstract: In the present paper, a numerical investigation has
been carried out to classify and clarify the effects of paramount
parameters on turbulent impinging slot jets. The effects of nozzle-s
exit turbulent intensity, distance between nozzle and impinging plate
are studied at Reynolds number 5000 and 20000. In addition, the
effect of Mach number that is varied between 0.3-0.8 at a constant
Reynolds number 133000 is investigated to elucidate the effect of
compressibility in impinging jet upon a flat plate. The wall that is
located at the same level with nozzle-s exit confines the flow. A
compressible finite volume solver is implemented for simulation the
flow behavior. One equation Spalart-Allmaras turbulent model is
used to simulate turbulent flow at this study. Assessment of the
Spalart-Allmaras turbulent model at high nozzle to plate distance,
and giving enough insights to characterize the effect of Mach number
at high Reynolds number for the complex impinging jet flow are the
remarkable results of this study.
Abstract: Visually impaired people find it extremely difficult to
acquire basic and vital information necessary for their living.
Therefore, they are at a very high risk of being socially excluded as a
result of poor access to information. In recent years, several attempts
have been made in improving the communication methods for
visually impaired people which involve tactile sensation such as
finger Braille, manual alphabets and the print on palm method and
several other electronic devices. But, there are some problems which
arise in such methods such as lack of privacy and lack of
compatibility to computer environment. This paper describes a low
cost Braille hand glove for blind people using slot sensors and
vibration motors with the help of which they can read and write emails,
text messages and read e-books. This glove allows the person
to type characters based on different Braille combination using six
slot sensors. The vibration in six different positions of the glove
which matches to the Braille code allows them to read characters.
Abstract: A new code synchronization algorithm is proposed in
this paper for the secondary cell-search stage in wideband CDMA
systems. Rather than using the Cyclically Permutable (CP) code in the
Secondary Synchronization Channel (S-SCH) to simultaneously
determine the frame boundary and scrambling code group, the new
synchronization algorithm implements the same function with less
system complexity and less Mean Acquisition Time (MAT). The
Secondary Synchronization Code (SSC) is redesigned by splitting into
two sub-sequences. We treat the information of scrambling code group
as data bits and use simple time diversity BCH coding for further
reliability. It avoids involved and time-costly Reed-Solomon (RS)
code computations and comparisons. Analysis and simulation results
show that the Synchronization Error Rate (SER) yielded by the new
algorithm in Rayleigh fading channels is close to that of the
conventional algorithm in the standard. This new synchronization
algorithm reduces system complexities, shortens the average
cell-search time and can be implemented in the slot-based cell-search
pipeline. By taking antenna diversity and pipelining correlation
processes, the new algorithm also shows its flexible application in
multiple antenna systems.
Abstract: This paper presents the theoretical investigation of a
slotted patch antenna. The main objective of proposed work is to
obtain a large bandwidth antenna with reduced size. The antenna has
a compact size of 21.1mm x 20.25mm x 8.5mm. Two designs with
minor variation are studied which provide wide impedance
bandwidths of 24.056% and 25.63% respectively with the use of
parasitic elements when excited by a probe feed. The advantages of
this configuration are its compact size and the wide range of
frequencies covered. A parametric study is also conducted to
investigate the characteristics of the antenna under different
conditions. The measured return loss and radiation pattern indicate
the suitability of this design for WLAN applications, namely, Wi-
Max, 802.11a/b/g and ISM bands.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetically and thermal stresses remain major failures
for insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: In this paper, we investigate the study of techniques
for scheduling users for resource allocation in the case of multiple
input and multiple output (MIMO) packet transmission systems. In
these systems, transmit antennas are assigned to one user or
dynamically to different users using spatial multiplexing. The
allocation of all transmit antennas to one user cannot take full
advantages of multi-user diversity. Therefore, we developed the case
when resources are allocated dynamically. At each time slot users
have to feed back their channel information on an uplink feedback
channel. Channel information considered available in the schedulers
is the zero forcing (ZF) post detection signal to interference plus
noise ratio. Our analysis study concerns the round robin and the
opportunistic schemes.
In this paper, we present an overview and a complete capacity
analysis of these schemes. The main results in our study are to give
an analytical form of system capacity using the ZF receiver at the
user terminal. Simulations have been carried out to validate all
proposed analytical solutions and to compare the performance of
these schemes.
Abstract: UWB is a very attractive technology for many
applications. It provides many advantages such as fine resolution and high power efficiency. Our interest in the current study is the use of
UWB radar technique in microwave medical imaging systems, especially for early breast cancer detection. The Federal Communications Commission FCC allowed frequency bandwidth of
3.1 to 10.6 GHz for this purpose. In this paper we suggest an UWB Bowtie slot antenna with enhanced bandwidth. Effects of varying the geometry of the antenna
on its performance and bandwidth are studied. The proposed antenna
is simulated in CST Microwave Studio. Details of antenna design and
simulation results such as return loss and radiation patterns are discussed in this paper. The final antenna structure exhibits good
UWB characteristics and has surpassed the bandwidth requirements.
Abstract: The purpose of the present study is to analyze the
effect of the target plate-s curvature on the heat transfer in laminar
confined impinging jet flows. Numerical results from two
dimensional compressible finite volume solver are compared
between three different shapes of impinging plates: Flat, Concave
and Convex plates. The remarkable result of this study proves that
the stagnation Nusselt number in laminar range of Reynolds number
based on the slot width is maximum in convex surface and is
minimum in concave plate. These results refuse the previous data in
literature stating the amount of the stagnation Nusselt number is
greater in concave surface related to flat plate configuration.