Abstract: This paper presents a dynamic adaptation scheme for
the frequency of inter-deme migration in distributed genetic algorithms
(GA), and its VLSI hardware design. Distributed GA,
or multi-deme-based GA, uses multiple populations which evolve
concurrently. The purpose of dynamic adaptation is to improve
convergence performance so as to obtain better solutions. Through
simulation experiments, we proved that our scheme achieves better
performance than fixed frequency migration schemes.
Abstract: Target tracking and localization are important applications
in wireless sensor networks. In these applications, sensor nodes
collectively monitor and track the movement of a target. They have
limited energy supplied by batteries, so energy efficiency is essential
for sensor networks. Most existing target tracking protocols need to
wake up sensors periodically to perform tracking. Some unnecessary
energy waste is thus introduced. In this paper, an energy efficient
protocol for target localization is proposed. In order to preserve
energy, the protocol fixes the number of sensors for target tracking,
but it retains the quality of target localization in an acceptable
level. By selecting a set of sensors for target localization, the other
sensors can sleep rather than periodically wake up to track the target.
Simulation results show that the proposed protocol saves a significant
amount of energy and also prolongs the network lifetime.
Abstract: This paper presents the use of anti-sway angle control
approaches for a two-dimensional gantry crane with disturbances
effect in the dynamic system. Delayed feedback signal (DFS) and
proportional-derivative (PD)-type fuzzy logic controller are the
techniques used in this investigation to actively control the sway
angle of the rope of gantry crane system. A nonlinear overhead
gantry crane system is considered and the dynamic model of the
system is derived using the Euler-Lagrange formulation. A complete
analysis of simulation results for each technique is presented in time
domain and frequency domain respectively. Performances of both
controllers are examined in terms of sway angle suppression and
disturbances cancellation. Finally, a comparative assessment of the
impact of each controller on the system performance is presented and
discussed.
Abstract: In the past years, the world has witnessed significant work in the field of Manufacturing. Special efforts have been made in the implementation of new technologies, management and control systems, among many others which have all evolved the field. Closely following all this, due to the scope of new projects and the need of turning the existing flexible ideas into more autonomous and intelligent ones, i.e.: moving toward a more intelligent manufacturing, the present paper emerges with the main aim of contributing to the analysis and a few customization issues of a new iCIM 3000 system at the IPSAM. In this process, special emphasis in made on the material flow problem. For this, besides offering a description and analysis of the system and its main parts, also some tips on how to define other possible alternative material flow scenarios and a partial analysis of the combinatorial nature of the problem are offered as well. All this is done with the intentions of relating it with the use of simulation tools, for which these have been briefly addressed with a special focus on the Witness simulation package. For a better comprehension, the previous elements are supported by a few figures and expressions which would help obtaining necessary data. Such data and others will be used in the future, when simulating the scenarios in the search of the best material flow configurations.
Abstract: Lately, significant work in the area of Intelligent
Manufacturing has become public and mainly applied within the
frame of industrial purposes. Special efforts have been made in the
implementation of new technologies, management and control
systems, among many others which have all evolved the field. Aware
of all this and due to the scope of new projects and the need of
turning the existing flexible ideas into more autonomous and
intelligent ones, i.e.: Intelligent Manufacturing, the present paper
emerges with the main aim of contributing to the design and analysis
of the material flow in either systems, cells or work stations under
this new “intelligent" denomination. For this, besides offering a
conceptual basis in some of the key points to be taken into account
and some general principles to consider in the design and analysis of
the material flow, also some tips on how to define other possible
alternative material flow scenarios and a classification of the states a
system, cell or workstation are offered as well. All this is done with
the intentions of relating it with the use of simulation tools, for which
these have been briefly addressed with a special focus on the Witness
simulation package. For a better comprehension, the previous
elements are supported by a detailed layout, other figures and a few
expressions which could help obtaining necessary data. Such data and
others will be used in the future, when simulating the scenarios in the
search of the best material flow configurations.
Abstract: Supersonic hydrogen-air cylindrical mixing layer is
numerically analyzed to investigate the effect of inlet swirl on
ignition time delay in scramjets. Combustion is treated using detail
chemical kinetics. One-equation turbulence model of Spalart and
Allmaras is chosen to study the problem and advection upstream
splitting method is used as computational scheme. The results show
that swirling both fuel and oxidizer streams may drastically decrease
the ignition distance in supersonic combustion, unlike using the swirl
just in fuel stream which has no helpful effect.
Abstract: The paper presents a simple and an accurate formula
that has been developed for the conduction angle (δ) of a single
phase half-wave or full-wave controlled rectifier with RL load. This
formula can be also used for calculating the conduction angle (δ) in
case of A.C. voltage regulator with inductive load under
discontinuous current mode. The simulation results shows that the
conduction angle calculated from the developed formula agree very
well with that obtained from the exact solution arrived from the
iterative method. Applying the developed formula can reduce the
computational time and reduce the time for manual classroom
calculation. In addition, the proposed formula is attractive for real
time implementations.
Abstract: The main aim of this research is to develop a methodology to encourage people's awareness, knowledge and understanding on the participation of flood management for cultural heritage, as the cooperation and interaction among government section, private section, and public section through role-play gaming simulation theory. The format of this research is to develop Role-play gaming simulation from existing documents, game or role-playing from several sources and existing data of the research site. We found that role-play gaming simulation can be implemented to help improving the understanding of the existing problem and the impact of the flood on cultural heritage, and the role-play game can be developed into the tool to improve people's knowledge, understanding and awareness about people's participation for flood management on cultural heritage, moreover the cooperation among the government, private section and public section will be improved through the theory of role-play gaming simulation.
Abstract: To investigate the energy performance of solar shading devices, this paper carried out a survey on the current status of solar shading utilization in buildings in Ningbo and performed building simulations to evaluate the energy savings potential by adopting different solar shading devices. Results show that solar shading utilization in this area is not popular and effective, and should be considered firstly in the design stage since the potential for energy savings is up to 6.8% for residential buildings and 9.4% for commercial buildings.
Abstract: Due to the stringent legislation for emission of diesel
engines and also increasing demand on fuel consumption, the
importance of detailed 3D simulation of fuel injection, mixing and
combustion have been increased in the recent years. In the present
work, FIRE code has been used to study the detailed modeling of
spray and mixture formation in a Caterpillar heavy-duty diesel
engine. The paper provides an overview of the submodels
implemented, which account for liquid spray atomization, droplet
secondary break-up, droplet collision, impingement, turbulent
dispersion and evaporation. The simulation was performed from
intake valve closing (IVC) to exhaust valve opening (EVO). The
predicted in-cylinder pressure is validated by comparing with
existing experimental data. A good agreement between the predicted
and experimental values ensures the accuracy of the numerical
predictions collected with the present work. Predictions of engine
emissions were also performed and a good quantitative agreement
between measured and predicted NOx and soot emission data were
obtained with the use of the present Zeldowich mechanism and
Hiroyasu model. In addition, the results reported in this paper
illustrate that the numerical simulation can be one of the most
powerful and beneficial tools for the internal combustion engine
design, optimization and performance analysis.
Abstract: Modeling of the dynamic behavior and motion are
renewed interest in the improved tractive performance of an
intelligent air-cushion tracked vehicle (IACTV). This paper presents
a new dynamical model for the forces on the developed small scale
intelligent air-cushion tracked vehicle moving over swamp peat. The
air cushion system partially supports the 25 % of vehicle total weight
in order to make the vehicle ground contact pressure 7 kN/m2. As the
air-cushion support system can adjust automatically on the terrain, so
the vehicle can move over the terrain without any risks. The springdamper
system is used with the vehicle body to control the aircushion
support system on any undulating terrain by making the
system sinusoidal form. Experiments have been carried out to
investigate the relationships among tractive efficiency, slippage,
traction coefficient, load distribution ratio, tractive effort, motion
resistance and power consumption in given terrain conditions.
Experiment and simulation results show that air-cushion system
improves the vehicle performance by keeping traction coefficient of
71% and tractive efficiency of 62% and the developed model can
meet the demand of transport efficiency with the optimal power
consumption.
Abstract: In this paper a stochastic scenario-based model predictive control applied to molten salt storage systems in concentrated solar tower power plant is presented. The main goal of this study is to build up a tool to analyze current and expected future resources for evaluating the weekly power to be advertised on electricity secondary market. This tool will allow plant operator to maximize profits while hedging the impact on the system of stochastic variables such as resources or sunlight shortage.
Solving the problem first requires a mixed logic dynamic modeling of the plant. The two stochastic variables, respectively the sunlight incoming energy and electricity demands from secondary market, are modeled by least square regression. Robustness is achieved by drawing a certain number of random variables realizations and applying the most restrictive one to the system. This scenario approach control technique provides the plant operator a confidence interval containing a given percentage of possible stochastic variable realizations in such a way that robust control is always achieved within its bounds. The results obtained from many trajectory simulations show the existence of a ‘’reliable’’ interval, which experimentally confirms the algorithm robustness.
Abstract: This paper addresses the problem of the partial state
feedback stabilization of a class of nonlinear systems. In order to
stabilization this class systems, the especial place of this paper is
to reverse designing the state feedback control law from the method
of judging system stability with the center manifold theory. First of
all, the center manifold theory is applied to discuss the stabilization
sufficient condition and design the stabilizing state control laws for a
class of nonlinear. Secondly, the problem of partial stabilization for a
class of plane nonlinear system is discuss using the lyapunov second
method and the center manifold theory. Thirdly, we investigate specially
the problem of the stabilization for a class of homogenous plane
nonlinear systems, a class of nonlinear with dual-zero eigenvalues and
a class of nonlinear with zero-center using the method of lyapunov
function with homogenous derivative, specifically. At the end of this
paper, some examples and simulation results are given show that the
approach of this paper to this class of nonlinear system is effective
and convenient.
Abstract: In this paper, a nonlinear delay population model is investigated. Choosing the delay as a bifurcation parameter, we demonstrate that Hopf bifurcation will occur when the delay exceeds a critical value. Global existence of bifurcating periodic solutions is established. Numerical simulations supporting the theoretical findings are included.
Abstract: DNA shuffling is a powerful method used for in vitro
evolute molecules with specific functions and has application in areas
such as, for example, pharmaceutical, medical and agricultural
research. The success of such experiments is dependent on a variety
of parameters and conditions that, sometimes, can not be properly
pre-established. Here, two computational models predicting DNA
shuffling results is presented and their use and results are evaluated
against an empirical experiment. The in silico and in vitro results
show agreement indicating the importance of these two models and
motivating the study and development of new models.
Abstract: Wireless Sensor Networks (WSNs) are wireless
networks consisting of number of tiny, low cost and low power
sensor nodes to monitor various physical phenomena like
temperature, pressure, vibration, landslide detection, presence of any
object, etc. The major limitation in these networks is the use of nonrechargeable
battery having limited power supply. The main cause of
energy consumption WSN is communication subsystem. This paper
presents an efficient grid formation/clustering strategy known as Grid
based level Clustering and Aggregation of Data (GCAD). The
proposed clustering strategy is simple and scalable that uses low duty
cycle approach to keep non-CH nodes into sleep mode thus reducing
energy consumption. Simulation results demonstrate that our
proposed GCAD protocol performs better in various performance
metrics.
Abstract: An optimal power flow (OPF) based on particle swarm
optimization (PSO) was developed with more realistic generator
security constraint using the capability curve instead of only Pmin/Pmax
and Qmin/Qmax. Neural network (NN) was used in designing digital
capability curve and the security check algorithm. The algorithm is
very simple and flexible especially for representing non linear
generation operation limit near steady state stability limit and under
excitation operation area. In effort to avoid local optimal power flow
solution, the particle swarm optimization was implemented with
enough widespread initial population. The objective function used in
the optimization process is electric production cost which is
dominated by fuel cost. The proposed method was implemented at
Java Bali 500 kV power systems contain of 7 generators and 20
buses. The simulation result shows that the combination of generator
power output resulted from the proposed method was more economic
compared with the result using conventional constraint but operated
at more marginal operating point.
Abstract: This paper features the modeling and design of a Fast
Output Sampling (FOS) Feedback control technique for the Active
Vibration Control (AVC) of a smart flexible aluminium cantilever
beam for a Single Input Single Output (SISO) case. Controllers are
designed for the beam by bonding patches of piezoelectric layer as
sensor / actuator to the master structure at different locations along
the length of the beam by retaining the first 2 dominant vibratory
modes. The entire structure is modeled in state space form using the
concept of piezoelectric theory, Euler-Bernoulli beam theory, Finite
Element Method (FEM) and the state space techniques by dividing
the structure into 3, 4, 5 finite elements, thus giving rise to three
types of systems, viz., system 1 (beam divided into 3 finite
elements), system 2 (4 finite elements), system 3 (5 finite elements).
The effect of placing the sensor / actuator at various locations along
the length of the beam for all the 3 types of systems considered is
observed and the conclusions are drawn for the best performance and
for the smallest magnitude of the control input required to control the
vibrations of the beam. Simulations are performed in MATLAB. The
open loop responses, closed loop responses and the tip displacements
with and without the controller are obtained and the performance of
the proposed smart system is evaluated for vibration control.
Abstract: This study is concerned with a new adaptive impedance control strategy to compensate for unknown time-varying environment stiffness and position. The uncertainties are expressed by Function Approximation Technique (FAT), which allows the update laws to be derived easily using Lyapunov stability theory. Computer simulation results are presented to validate the effectiveness of the proposed strategy.
Abstract: In this research paper we have presented control
architecture for robotic arm movement and trajectory planning using
Fuzzy Logic (FL) and Genetic Algorithms (GAs). This architecture is
used to compensate the uncertainties like; movement, friction and
settling time in robotic arm movement. The genetic algorithms and
fuzzy logic is used to meet the objective of optimal control
movement of robotic arm. This proposed technique represents a
general model for redundant structures and may extend to other
structures. Results show optimal angular movement of joints as result
of evolutionary process. This technique has edge over the other
techniques as minimum mathematics complexity used.