Abstract: This work attempts to improve the permselectivity of poly-ortho-phenylenediamine (PPD) coating for glutamate biosensor applications on Pt microelectrode, using constant potential amperometry and cyclic voltammetry. Percentage permeability of the modified PPD microelectrode was carried out towards hydrogen peroxide (H2O2) and ascorbic acid (AA) whereas permselectivity represents the percentage interference by AA in H2O2 detection. The 50-μm diameter Pt disk microelectrode showed a good permeability value toward H2O2 (95%) and selectivity against AA (0.01%) compared to other sizes of electrode studied here. The electrode was further modified with glutamate oxidase (GluOx) that was immobilized and cross linked with glutaraldehyde (GA, 0.125%), resulting in Pt/PPD/GluOx-GA electrode design. The maximum current density Jmax and apparent Michaelis constant, KM, obtained on Pt/PPD/GluOx-GA electrodes were 48 μA cm-2 and 50 μM, respectively. The linear region slope (LRS) was 0.96 μA cm-2 mM-1. The detection limit (LOD) for glutamate was 3.0 ± 0.6 μM. This study shows a promising glutamate microbiosensor for brain glutamate detection.
Abstract: The acidity of different raw Jordanian clays
containing zeolite, bentonite, red and white kaolinite and diatomite
was characterized by means of temperature programmed desorption
(TPD) of ammonia, conversion of 2-methyl-3-butyn-2-ol (MBOH),
FTIR and BET-measurements. FTIR spectra proved presence of
silanol and bridged hydroxyls on the clay surface. The number of
acidic sites was calculated from experimental TPD-profiles. We
observed the decrease of surface acidity correlates with the decrease
of Si/Al ratio except for diatomite. On the TPD-plot for zeolite two
maxima were registered due to different strength of surface acidic
sites. Values of MBOH conversion, product yields and selectivity
were calculated for the catalysis on Jordanian clays. We obtained that
all clay samples are able to convert MBOH into a major product
which is 3-methyl-3-buten-1-yne (MBYNE) catalyzed by acid
surface sites with the selectivity close to 70%. There was found a
correlation between MBOH conversion and acidity of clays
determined by TPD-NH3, i.e. the higher the acidity the higher the
conversion of MBOH. However, diatomite provided the lowest
conversion of MBOH as result of poor polarization of silanol groups.
Comparison of surface areas and conversions revealed the highest
density of active sites for red kaolinite and the lowest for zeolite and
diatomite.
Abstract: Sol-gel immobilization of enzymes, which can improve considerably their properties, is now one of the most used techniques. By deposition of the entrapped lipase on a solid support, a new and improved biocatalyst was obtained, which can be used with excellent results in acylation reactions. In this paper, lipase B from Candida antarctica was double immobilized on different adsorbents. These biocatalysts were employed in the kinetic resolution of several aliphatic secondary alcohols in organic medium. High total recovery yields of enzymatic activity, up to 560%, were obtained. For all the studied alcohols the enantiomeric ratios E were over 200. The influence of the reaction medium was studied for the kinetic resolution of 2-pentanol.
Abstract: Image fusion aims to enhance the perception
of a scene by combining important information captured by
different sensors. Dual-Tree Complex Wavelet (DT-CWT) has been
thouroughly investigated for image fusion, since it takes advantages
of approximate shift invariance and direction selectivity. But it can
only handle limited direction information. To allow a more flexible
directional expansion for images, we propose a novel fusion scheme,
referred to as complex contourlet transform (CCT). It successfully
incorporates directional filter banks (DFB) into DT-CWT. As a result
it efficiently deal with images containing contours and textures,
whereas it retains the property of shift invariance. Experimental
results demonstrated that the method features high quality fusion
performance and can facilitate many image processing applications.
Abstract: This paper investigates the performance of Multiple- Input Multiple-Output (MIMO) feedback system combined with Orthogonal Frequency Division Multiplexing (OFDM). Two types of codebook based channel feedback techniques are used in this work. The first feedback technique uses a combination of both the long-term and short-term channel state information (CSI) at the transmitter, whereas the second technique uses only the short term CSI. The long-term and short-term CSI at the transmitter is used for efficient channel utilization. OFDM is a powerful technique employed in communication systems suffering from frequency selectivity. Combined with multiple antennas at the transmitter and receiver, OFDM proves to be robust against delay spread. Moreover, it leads to significant data rates with improved bit error performance over links having only a single antenna at both the transmitter and receiver. The effectiveness of these techniques has been demonstrated through the simulation of a MIMO-OFDM feedback system. The results have been evaluated for 4x4 MIMO channels. Simulation results indicate the benefits of the MIMO-OFDM channel feedback system over the one without incorporating OFDM. Performance gain of about 3 dB is observed for MIMO-OFDM feedback system as compared to the one without employing OFDM. Hence MIMO-OFDM becomes an attractive approach for future high speed wireless communication systems.
Abstract: The upgrading of low quality crude natural gas (NG) is attracting interest due to high demand of pipeline-grade gas in recent years. Membrane processes are commercially proven technology for the removal of impurities like carbon dioxide from NG. In this work, cross flow mathematical model has been suggested to be incorporated with ASPEN HYSYS as a user defined unit operation in order to design the membrane system for CO2/CH4 separation. The effect of operating conditions (such as feed composition and pressure) and membrane selectivity on the design parameters (methane recovery and total membrane area required for the separation) has been studied for different design configurations. These configurations include single stage (with and without recycle) and double stage membrane systems (with and without permeate or retentate recycle). It is shown that methane recovery can be improved by recycling permeate or retentate stream as well as by using double stage membrane systems. The ASPEN HYSYS user defined unit operation proposed in the study has potential to be applied for complex membrane system design and optimization.
Abstract: The Ni/α-Al2O3 catalysts with different amounts of La
as promoter from 0 to 4 wt % were prepared, characterized and their
catalytic activity was investigated in syngas methanation reaction.
Effects of reaction temperature and lanthanum loading on carbon
oxides conversion and methane selectivity were also studied. Adding
certain amount of lanthanum to 10Ni /α-Al2O3 catalysts can decrease
the average NiO crystallite diameter which leads to higher activity and
stability while excessive addition would cause deactivation quickly.
Stability on stream towards deactivation was observed up to 800 min
at 500 °C, 0.1MPa and 600000 mL·g-1·h-1.
Abstract: The catalytic dehydroxylation of glycerol to propylene
glycol was investigated over Cu-ZnO/Al2O3 prepared by incipient
wetness impregnation (IWI) method with different purity feedstocks -
refined glycerol and technical grade glycerol. The main purpose is to
investigate the effects of feed impurities that cause the catalyst
deactivation. The prepared catalyst were tested for its catalytic
activity and selectivity in a continuous flow fixed bed reactor at 523
K, 500 psig, H2/feed molar ratio of 4 and WHSV of 3 h-1. The results
showed that conversion of refined glycerol and technical grade
glycerol at time on stream 6 hour are 99% and 71% and selectivity to
propylene glycol are 87% and 56% respectively. The ICP-EOS and
TPO results indicated that the cause of catalyst deactivation was the
amount of impurities in the feedstock. The higher amount of
impurities (especially Na and K) the lower catalytic activity.
Abstract: Hydrothermally synthesized high silica borosilicates
with the MFI structure was subjected to several characterization
techniques. The effect of boron on the structure and acidity of
HZSM-5 catalyst were studied by XRD, SEM, N2 adsorption, solid
state NMR, NH3-TPD. It was confirmed that boron had entered the
framework in the boron samples. The results also revealed that strong
acidity was weakened and weak acidity was strengthened by the
boron added zeolite framework compared with parent catalyst. The
catalytic performance was carried out in a fixed bed at 460°C for
methanol to propylene (MTP) reaction. The results of MTP reaction
showed a great increment of the propylene selectivity and excellent
stability for the B-HZSM-5. The catalyst exhibited about 81%
selectivity to C2
= - C4
= olefins with 40% selectivity of propylene as
major component at near 100% methanol conversion, and the stable
performance in the studied period was 100h.
Abstract: Hydrogenated biodiesel is one of the most promising
renewable fuels. It has many advantages over conventional biodiesel,
including higher cetane number, higher heating value, lower
viscosity, and lower corrosiveness due to its absence of oxygen.
From previous work, Pd/TiO2 gave high conversion and selectivity in
hydrogenated biodiesel. In this work, the effect of biomass feedstocks
(i.e. beef fat, chicken fat, pork fat, and jatropha oil) on the production
of hydrogenated biodiesel over Pd/TiO2 has been studied. Biomass
feedstocks were analyzed by ICP-OES (inductively coupled plasma
optical emission spectrometry) to identify the content of impurities
(i.e. P, K, Ca, Na, and Mg). The deoxygenation catalyst, Pd/TiO2,
was prepared by incipient wetness impregnation (IWI) and tested in a
continuous flow packed-bed reactor at 500 psig, 325°C, H2/feed
molar ratio of 30, and LHSV of 4 h-1 for its catalytic activity and
selectivity in hydrodeoxygenation. All feedstocks gave high
selectivity in diesel specification range hydrocarbons and the main
hydrocarbons were n-pentadecane (n-C15) and n-heptadecane (n-
C17), resulting from the decarbonylation/decarboxylation reaction.
Intermediates such as oleic acid, stearic acid, palmitic acid, and esters
were also detected in minor amount. The conversion of triglycerides
in jatropha oil is higher than those of chicken fat, pork fat, and beef
fat, respectively. The higher concentration of metal impurities in
feedstock, the lower conversion of feedstock.
Abstract: The selective recovery of heavy metals of Cu, Zn, Ni and Cr from a mixed plating sludge by sulfidation and oxidation treatment was targeted in this study. At first, the mixed plating sludge was simultaneously subjected to an extraction and Cu sulfidation process at pH=1.5 to dissolve heavy metals and to precipitate Cu2+ as CuS. In the next step, the sulfidation treatment of Zn was carried out at pH=4.5 and the residual solution was subjected to an oxidation treatment of chromium with H2O2 at pH=10.0. After the experiments, the selectivity of metal precipitation and the chromium oxidation ratio were evaluated. As results, it was found that the filter cake obtained after selective sulfidation of Cu was composed of 96.6% of Cu (100% equals to the sum of Cu, Zn, Ni and Cr contents). Such findings confirmed that almost complete extraction of heavy metals was achieved at pH=1.5 and also that Cu could be selectively recovered as CuS. Further, the filter cake obtained at pH=4.5 was composed of 91.5% Zn and 6.83% of Cr. Regarding the chromium oxidation step, the chromium oxidation ratio was found to increase with temperature and the addition of oxidation agent of H2O2, but only oxidation ratio of 59% was achieved at a temperature of 60°C and H2O2 to Cr3+ equivalent ratio of 180.
Abstract: This paper presents a new ultra-wideband (UWB) bandpass filter (BPF) with sharp roll-off and dual-notched bands. The filter consists of a triangle ring multi-mode resonator (MMR) with the stub-loaded resonator (SLR) for controlling the two transmission zeros at 2.8 / 11 GHz, the embedded open-circuited stub and the asymmetric tight coupled input/output (I/O) lines for introducing the dual notched bands at 5.2 / 6.8 GHz. The attenuation slope in the lower and higher passband edges of the proposed filter show 160- and 153-dB/GHz, respectively. This study mainly provides a simple method to design a UWB bandpass filter with high passband selectivity and dual-notched bands for satisfying the Federal Communications Commission (FCC-defined) indoor UWB specification
Abstract: The expression of LFA-1 diverges from the
physiological condition, thus active targeting carrier can provide the
benefits from difference into LFA-1 expression in various conditions.
Here, the selectivity of cIBR-conjugated nanoparticles (cIBR-NPs),
in terms of uptake, was investigated using PBMCs, Mixed PBMCMolt-
3 cells and Molt-3 cells. The expressions of LFA-1 on Molt-3
cells, from flow cytometry and Western blot, possessed the highest
level whereas PBMCs showed the lowest level. The kinetic uptake
profiles of cIBR-NPs were obtained by flow cytometry, which the
degree of cellular uptake presented a similar trend with the level of
LFA-1 indicating the influence of LFA-1 expression on the cellular
uptake of cIBR-NPs. The conformation of LFA-1 had a slight effect
on the cellular uptake of cIBR-NPs. Overall we demonstrated that
cIBR-NPs enhanced cellular uptake and improved the selectivity of
drug carriers to LFA-1 on the leukemia cells, which related with the
order of LFA-1 expression.
Abstract: The main aim of this work is to develop a model of hydrogen sulfide (H2S) separation from natural gas by using membrane separation technology. The model is developed by incorporating three diffusion mechanisms which are Knudsen, viscous and surface diffusion towards membrane selectivity and permeability. The findings from the simulation result shows that the permeability of the gas is dependent toward the pore size of the membrane, operating pressure, operating temperature as well as feed composition. The permeability of methane has the highest value for Poly (1-trimethylsilyl-1-propyne ) PTMSP membrane at pore size of 0.1nm and decreasing toward a minimum peak at pore range 1 to 1.5 nm as pore size increased before it increase again for pore size is greater than 1.5 nm. On the other hand, the permeability of hydrogen sulfide is found to increase almost proportionally with the increase of membrane pore size. Generally, the increase of pressure will increase the permeability of gas since more driving force is provided to the system while increasing of temperature would decrease the permeability due to the surface diffusion drop off effect. A corroboration of the simulation result also showed a good agreement with the experimental data.
Abstract: The effects of ethylene (C2H4) feed position and
O2/C2H4 feed molar ratio on ethylene epoxidation in a parallel
dielectric barrier discharge (DBD) were studied. The results showed
that the ethylene feed position fraction of 0.5 and the feed molar
ratio of O2/C2H4 of 0.2:1 gave the highest EO selectivity of 34.3%
and the highest EO yield of 5.28% with low power consumptions of
2.11×10-16 Ws/molecule of ethylene converted and 6.34×10-16
Ws/molecule of EO produced when the DBD system was operated
under the best conditions: an applied voltage of 19 kV, an input
frequency of 500 Hz and a total feed flow rate of 50 cm3/min. The
separate ethylene feed system provided much higher epoxidation
activity as compared to the mixed feed system which gave EO
selectivity of 15.5%, EO yield of 2.1% and the power consumption of
EO produced of 7.7×10-16 Ws/molecule.
Abstract: Based on a global kinetics of direct dimethyl ether (DME) synthesis process from syngas, a steady-state one-dimensional mathematical model for the bubble column slurry reactor (BCSR) has been established. It was built on the assumption of plug flow of gas phase, sedimentation-dispersion model of catalyst grains and isothermal chamber regardless of reaction heats and rates for the design of an industrial scale bubble column slurry reactor. The simulation results indicate that higher pressure and lower temperature were favorable to the increase of CO conversion, DME selectivity, products yield and the height of slurry bed, which has a coincidence with the characteristic of DME synthesis reaction system, and that the height of slurry bed is lessen with the increasing of operation temperature in the range of 220-260℃. CO conversion, the optimal operation conditions in BCSR were proposed.
Abstract: Cyclic delay diversity (CDD) is a simple technique to
intentionally increase frequency selectivity of channels for orthogonal
frequency division multiplexing (OFDM).This paper proposes a residual
carrier frequency offset (RFO) estimation scheme for OFDMbased
broadcasting system using CDD. In order to improve the RFO
estimation, this paper addresses a decision scheme of the amount of
cyclic delay and pilot pattern used to estimate the RFO. By computer
simulation, the proposed estimator is shown to benefit form propoerly
chosen delay parameter and perform robustly.
Abstract: Chemical detection is still a continuous challenge when
it comes to designing single-walled carbon nanotube (SWCNT)
sensors with high selectivity, especially in complex chemical
environments. A perfect example of such an environment would be in
thermally oxidized soybean oil. At elevated temperatures, oil oxidizes
through a series of chemical reactions which results in the formation of
monoacylglycerols, diacylglycerols, oxidized triacylglycerols, dimers,
trimers, polymers, free fatty acids, ketones, aldehydes, alcohols,
esters, and other minor products. In order to detect the rancidity of
oxidized soybean oil, carbon nanotube chemiresistor sensors have
been coated with polyethylenimine (PEI) to enhance the sensitivity
and selectivity. PEI functionalized SWCNTs are known to have a high
selectivity towards strong electron withdrawing molecules. The
sensors were very responsive to different oil oxidation levels and
furthermore, displayed a rapid recovery in ambient air without the
need of heating or UV exposure.
Abstract: In this work, Experimental tie-line results and
solubility (binodal) curves were obtained for the ternary systems
(water + acetic acid + methyl isobutyl ketone (MIBK)), (water +
lactic acid+ methyl isobutyl ketone) at T = 294.15K and atmospheric
pressure. The consistency of the values of the experimental tie-lines
was determined through the Othmer-Tobias and Hands correlations.
For the extraction effectiveness of solvents, the distribution and
selectivity curves were plotted. In addition, these experimental tieline
data were also correlated with NRTL model. The interaction
parameters for the NRTL model were retrieved from the obtained
experimental results by means of a combination of the homotopy
method and the genetic algorithms.
Abstract: A series of 1-(1H-benzimidazol-2-yl)-3-(substituted phenyl)-2-propen-1-one were allowed to react with hydrazine hydrate and phenyl hydrazine in submitted reactions to get pyrazoline and phenyl pyrazoline derivatives. All the compounds entered for screening at the Tuberculosis Antimicrobial Acquisition and Coordinating Facility (TAACF) for their in vitro antibacterial activity against Mycobacterium tuberculosis H37Rv strain (ATCC 27294) using Microplate Alamar Blue Assay (MABA) susceptibility test. The results expressed as MIC (minimum inhibitory concentration) in μg/mL. Among the fifteen compounds, eight compounds were found to have MIC values less than 10 μg/mL. These were subjected for cytotoxicity assay in VERO cells to determine CC50 (cytotoxic concentration 50%) values and finally SI (Selectivity Index) were calculated. Compound (XV) 2-[5-(4- fluorophenyl)-1-phenyl-4,5-dihydro-1H-3-pyrazolyl]-1Hbenzimidazole was considered the best candidate of the series that could be a good starting point to develop new lead compounds in the fight against tuberculosis.