Abstract: In this research, a questionnaire survey was conducted
to measure nap, drowsiness and fatigue of drivers who work for long
shifts, to discuss about the work environment and health conditions for
taxi and bus drivers who work at night-time. The questionnaire sheet
used for this research was organized into the following categories:
tension/tiredness, drowsiness while driving, and the nap situation
during night-time work. The number of taxi drivers was 127 and the
number of bus drivers was 40. Concerning the results of a comparison
of nap hours of taxi and bus drivers, the taxi drivers’ nap hours are
overwhelmingly shorter, and also the frequency of drivers who
experience drowsiness is higher. The burden on bus drivers does not
change because of the system of a two-driver rotation shift. In
particular, the working environment of the taxi driver may lead to
greater fatigue accumulation than the bus driver’s environment.
Abstract: Crops diversity and maintaining and enhancing the
fertility of agricultural lands are basic principles of organic farming.
With a wider range of crops in agroecosystem can improve the ability
to control weeds, pests and diseases, and the performance of crops
rotation and food safety. In this sense, the main objective of the
research was to study the productivity and chemical composition of
some alternative crops and their adaptability to soil and climatic
conditions of the agricultural area in Southern Romania and to
cultivation in the organic farming system. The alternative crops were:
lentil (7 genotypes); five species of grain legumes (5 genotypes); four
species of oil crops (5 genotypes). The seed production was, on
average: 1343 kg/ha of lentil; 2500 kg/ha of field beans; 2400 kg/ha
of chick peas and blackeyed peas; more than 2000 kg/ha of atzuki
beans, over 1250 kg/ha of fenugreek; 2200 kg/ha of safflower; 570
kg/ha of oil pumpkin; 2150 kg/ha of oil flax; 1518 kg/ha of camelina.
Regarding chemical composition, lentil seeds contained: 22.18%
proteins, 3.03% lipids, 33.29% glucides, 4.00% minerals, and 259.97
kcal energy values. For field beans: 21.50% proteins, 4.40% lipids,
63.90% glucides, 5.85% minerals, 395.36 kcal energetic value. For
chick peas: 21.23% proteins, 4.55% lipids, 53.00% glucides, 3.67%
minerals, 348.22 kcal energetic value. For blackeyed peas: 23.30%
proteins, 2.10% lipids, 68.10% glucides, 3.93% minerals, 350.14 kcal
energetic value. For adzuki beans: 21.90% proteins, 2.60% lipids,
69.30% glucides, 4.10% minerals, 402.48 kcal energetic value. For
fenugreek: 21.30% proteins, 4.65% lipids, 63.83% glucides, 5.69%
minerals, 396.54 kcal energetic value. For safflower: 12.60%
proteins, 28.37% lipids, 46.41% glucides, 3.60% minerals, 505.78
kcal energetic value. For camelina: 20.29% proteins, 31.68% lipids,
36.28% glucides, 4.29% minerals, 526.63 kcal energetic value. For
oil pumpkin: 29.50% proteins, 36.92% lipids, 18.50% glucides,
5.41% minerals, 540.15 kcal energetic value. For oil flax: 22.56%
proteins, 34.10% lipids, 27.73% glucides, 5.25% minerals, 558.45
kcal energetic value.
Abstract: The output error of the globoidal cam mechanism can
be considered as a relevant indicator of mechanism performance,
because it determines kinematic and dynamical behavior of
mechanical transmission. Based on the differential geometry and the
rigid body transformations, the mathematical model of surface
geometry of the globoidal cam is established. Then we present the
analytical expression of the output error (including the transmission
error and the displacement error along the output axis) by considering
different manufacture and assembly errors. The effects of the center
distance error, the perpendicular error between input and output axes
and the rotational angle error of the globoidal cam on the output error
are systematically analyzed. A globoidal cam mechanism which is
widely used in automatic tool changer of CNC machines is applied for
illustration. Our results show that the perpendicular error and the
rotational angle error have little effects on the transmission error but
have great effects on the displacement error along the output axis. This
study plays an important role in the design, manufacture and assembly
of the globoidal cam mechanism.
Abstract: The design of high pressure water jet based polishing
equipment and its fabrication conducted in this study is reported
herein, together with some preliminary test results for assessing its
applicability for HMA surface polishing. This study also provides
preliminary findings concerning the test variables, such as the
rotational speed, the water jet pressure, the abrasive agent used, and
the impact angel that were experimentally investigated in this study. The preliminary findings based on four trial tests (two on large
slab specimens and two on small size gyratory compacted
specimens), however, indicate that both friction and texture values
tend to increase with the polishing durations for two combinations of
pressure and rotation speed of the rotary deck. It seems that the more
polishing action the specimen is subjected to; the aggregate edges are
created such that the surface texture values are increased with the
accompanied increase in friction values. It may be of interest (but
which is outside the scope of this study) to investigate if the similar
trend exist for HMA prepared with aggregate source that is sand and
gravel.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: Single angle connections, which are bolted to the beam
web and the column flange, are studied to investigate their
moment-rotation behavior. Elastic–perfectly plastic material behavior
is assumed. ABAQUS software is used to analyze the nonlinear
behavior of a single angle connection. The identical geometric and
material conditions with Lipson’s test are used for verifying finite
element models. Since Kishi and Chen’s Power model and Lee and
Moon’s Log model are accurate only for a limited range of mechanism,
simpler and more accurate hyperbolic function models are proposed.
Abstract: This paper aims to project the construction of a
prototype azimuthal thruster, mounted with materials of low cost and
easy access, testing in a controlled environment to measure their
performance, characteristics and feasibility of future projects. The
construction of the simulation of dynamic positioning software,
responsible for simulating a vessel and reposition it when necessary.
Validation tests were performed in the form of partial or complete
system. These tests validate the system manually or automatically.
The system provides an interface to the user and simulates the
conditions unfavorable positioning of a vessel, accurately calculates
the azimuth angle, the direction of rotation of the helix and the time
that this should be turned on so that the vessel back to position
original. A serial communication connects the Simulation Dynamic
Positioning System with Embedded System causing the usergenerated
data to simulate the DP system arrives in the form of
control signals to the motors of the propellant. This article addresses
issues in the marine industry employees.
Abstract: Let us consider that the entire universe is composed of
a single hydrogen atom within which the electron is moving around
the proton. In this case, according to classical theories of physics,
radiation, photons respectively, should be absorbed by the electron.
Depending on the number of photons absorbed, the electron radius of
rotation around the proton is established. Until now, the principle of
photons absorption by electrons and the electron transition to a new
energy level, namely to a higher radius of rotation around the proton,
is not clarified in physics. This paper aims to demonstrate that
radiation, photons respectively, have mass and negative electrostatic
charge similar to electrons but infinitely smaller. The experiments
which demonstrate this theory are simple: thermal expansion,
photoelectric effect and thermonuclear reaction.
Abstract: The aim of this research was to reveal the link
between mental variables, such as spatial abilities, memory, intellect
and professional experience of drivers.
Participants were allocated to four groups: no experience,
inexperienced, skilled and professionals (total 85 participants). The
level of ability for spatial navigation and indicator of nonverbal
memory grow along the process of accumulation of driving
experience. At high levels of driving experience, this tendency is
especially noticeable. The professionals having personal
achievements in driving (racing) differ from skilled drivers in better
feeling of direction, which is specific for them not just in a short-term
situation of an experimental task, but also in life-size perspective.
The level of ability of mental rotation does not grow with the growth
of driving experience, which confirms the multiple intelligence
theory according to which spatial abilities represent specific, other
than logical intelligence type of intellect. The link between spatial
abilities, memory, intellect and professional experience of drivers
seems to be different relating spatial navigation or mental rotation as
different kinds of spatial abilities.
Abstract: Under active stress conditions, a rigid cantilever
retaining wall tends to rotate about a pivot point located within the
embedded depth of the wall. For purely granular and cohesive soils, a
methodology was previously reported called minimization of moment
ratio to determine the location of the pivot point of rotation. The
usage of this new methodology is to estimate the rotational stability
safety factor. Moreover, the degree of improvement required in a
backfill to get a desired safety factor can be estimated by the concept
of the shear strength demand. In this article, the accuracy of this
method for another type of cantilever walls called Contiguous Bored
Pile (CBP) retaining wall is evaluated by using physical modeling
technique. Based on observations, the results of moment ratio
minimization method are in good agreement with the results of the
carried out physical modeling.
Abstract: The present study is concerned with the problem of determining the shape of the free surface flow in a hydraulic channel which has an uneven bottom. For the mathematical formulation of the problem, the fluid of the two-dimensional irrotational steady flow in water is assumed inviscid and incompressible. The solutions of the nonlinear problem are obtained by using the usual conformal mapping theory and Hilbert’s technique. An experimental study, for comparing the obtained results, has been conducted in a hydraulic channel (subcritical regime and supercritical regime).
Abstract: This paper addresses a cutting edge method of
business demand forecasting, based on an empirical probability
function when the historical behavior of the data is random.
Additionally, it presents error determination based on the numerical
method technique ‘propagation of errors.’ The methodology was
conducted characterization and process diagnostics demand planning
as part of the production management, then new ways to predict its
value through techniques of probability and to calculate their mistake
investigated, it was tools used numerical methods. All this based on
the behavior of the data. This analysis was determined considering
the specific business circumstances of a company in the sector of
communications, located in the city of Bogota, Colombia. In
conclusion, using this application it was possible to obtain the
adequate stock of the products required by the company to provide its
services, helping the company reduce its service time, increase the
client satisfaction rate, reduce stock which has not been in rotation
for a long time, code its inventory, and plan reorder points for the
replenishment of stock.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: The comprehensive CFD models have been used to
represent and study the heterogeneous combustion of biomass. In the
present work, the operation of a global flue gas circuit in the sugarcane
bagasse combustion, from wind boxes below primary air grate
supply, passing by bagasse insertion in swirl burners and boiler
furnace, to boiler bank outlet is simulated. It uses five different
meshes representing each part of this system located in sequence:
wind boxes and grate, boiler furnace, swirl burners, superheaters and
boiler bank. The model considers turbulence using standard k-ε,
combustion using EDM, radiation heat transfer using DTM with 16
ray directions and bagasse particle tracking represented by Schiller-
Naumann model. The results showed good agreement with expected
behavior found in literature and equipment design. The more detailed
results view in separated parts of flue gas system allows observing
some flow behaviors that cannot be represented by usual
simplifications like bagasse supply under homogeneous axial and
rotational vectors and others that can be represented using new
considerations like the representation of 26 thousand grate orifices by
144 rectangular inlets.
Abstract: This study investigates the use of a time-series of
MODIS NDVI data to identify agricultural land cover change on an
annual time step (2007 - 2012) and characterize the trend. Following
an ISODATA classification of the MODIS imagery to selectively
mask areas not agriculture or semi-natural, NDVI signatures were
created to identify areas cereals and vineyards with the aid of
ancillary, pictometry and field sample data for 2010. The NDVI
signature curve and training samples were used to create a decision
tree model in WEKA 3.6.9 using decision tree classifier (J48)
algorithm; Model 1 including ISODATA classification and Model 2
not. These two models were then used to classify all data for the
study area for 2010, producing land cover maps with classification
accuracies of 77% and 80% for Model 1 and 2 respectively. Model 2
was subsequently used to create land cover classification and change
detection maps for all other years. Subtle changes and areas of
consistency (unchanged) were observed in the agricultural classes
and crop practices. Over the years as predicted by the land cover
classification. Forty one percent of the catchment comprised of
cereals with 35% possibly following a crop rotation system.
Vineyards largely remained constant with only one percent
conversion to vineyard from other land cover classes.
Abstract: This study is about the structural transformations of
aluminium examining with the Dynamic Mechanical Thermal
Analyzer (DMTA). It is a faster and simpler measuring method to
make consequence about the metal’s structural transformations. The
device measures the changing of the mechanical characteristics
depending on the heating rate, and concludes certain transformations.
This measuring method fast and shows clean-cut results comparing
the conventional ways.
Applying polymer measuring devices for metal investigations is
not widespread method. One of the adaptable ways is shown in this
study. The article compares the results of the small specimen test and
the DMTA method, considering the temperature and the forming
dependence of recrystallization temperature.
Abstract: This paper deals with the theoretical and numerical
investigation of magneto hydrodynamic boundary layer flow of a
nanofluid past a wedge shaped wick in heat pipe used for the cooling
of electronic components and different type of machines. To
incorporate the effect of nanoparticle diameter, concentration of
nanoparticles in the pure fluid, nanothermal layer formed around the
nanoparticle and Brownian motion of nanoparticles etc., appropriate
models are used for the effective thermal and physical properties of
nanofluids. To model the rotation of nanoparticles inside the base
fluid, microfluidics theory is used. In this investigation ethylene
glycol (EG) based nanofluids, are taken into account. The non-linear
equations governing the flow and heat transfer are solved by using a
very effective particle swarm optimization technique along with
Runge-Kutta method. The values of heat transfer coefficient are
found for different parameters involved in the formulation viz.
nanoparticle concentration, nanoparticle size, magnetic field and
wedge angle etc. It is found that, the wedge angle, presence of
magnetic field, nanoparticle size and nanoparticle concentration etc.
have prominent effects on fluid flow and heat transfer characteristics
for the considered configuration.
Abstract: Machining of hard materials is a recent technology for
direct production of work-pieces. The primary challenge in
machining these materials is selection of cutting tool inserts which
facilitates an extended tool life and high-precision machining of the
component. These materials are widely for making precision parts for
the aerospace industry. Nickel-based alloys are typically used in
extreme environment applications where a combination of strength,
corrosion resistance and oxidation resistance material characteristics
are required. The present paper reports the theoretical and
experimental investigations carried out to understand the influence of
machining parameters on the response parameters. Considering the
basic machining parameters (speed, feed and depth of cut) a study has
been conducted to observe their influence on material removal rate,
surface roughness, cutting forces and corresponding tool wear.
Experiments are designed and conducted with the help of Central
Composite Rotatable Design technique. The results reveals that for a
given range of process parameters, material removal rate is favorable
for higher depths of cut and low feed rate for cutting forces. Low feed
rates and high values of rotational speeds are suitable for better finish
and higher tool life.
Abstract: The characteristics of temperature distribution and
electric field in a natural rubber glove (NRG) using microwave
energy during microwave heating process are investigated
numerically and experimentally. A three-dimensional model of NRG
and microwave oven are considered in this work. The influences of
position, heating time and rotation angle of NRG on temperature
distribution and electric field are presented in details. The coupled
equations of electromagnetic wave propagation and heat transfer are
solved using the finite element method (FEM). The numerical model
is validated with an experimental study at a frequency of 2.45 GHz.
The results show that the numerical results closely match the
experimental results. Furthermore, it is found that the temperature
distribution and electric field increases with increasing heating time.
The hot spot zone appears in NRG at the tip of middle finger while
the maximum temperature occurs in case of rotation angle of NRG =
60 degree. This investigation provides the essential aspects for a
fundamental understanding of heat transport of NRG using
microwave energy in industry.
Abstract: This paper proposes a rotational invariant texture
feature based on the roughness property of the image for psoriasis
image analysis. In this work, we have applied this feature for image
classification and segmentation. The fuzzy concept is employed to
overcome the imprecision of roughness. Since the psoriasis lesion is
modeled by a rough surface, the feature is extended for calculating
the Psoriasis Area Severity Index value. For classification and
segmentation, the Nearest Neighbor algorithm is applied. We have
obtained promising results for identifying affected lesions by using
the roughness index and severity level estimation.