Abstract: This research was conducted in the Lower Ping River
Basin downstream of the Bhumibol Dam and the Lower Wang River
Basin in Tak Province, Thailand. Most of the tributary streams of the
Ping can be considered as ungauged catchments. There are 10-
pumping station installation at both river banks of the Ping in Tak
Province. Recently, most of them could not fully operate due to the
water amount in the river below the level that would be pumping,
even though included water from the natural river and released flow
from the Bhumibol Dam. The aim of this research was to increase the
performance of those pumping stations using weir projects in the
Ping. Therefore, the river analysis system model (HEC-RAS) was
applied to study the hydraulic behavior of water surface profiles in
the Ping River with both cases of existing conditions and proposed
weirs during the violent flood in 2011 and severe drought in 2013.
Moreover, the hydrologic modeling system (HMS) was applied to
simulate lateral streamflow hydrograph from ungauged catchments of
the Ping. The results of HEC-RAS model calibration with existing
conditions in 2011 showed best trial roughness coefficient for the
main channel of 0.026. The simulated water surface levels fitted to
observation data with R2 of 0.8175. The model was applied to 3
proposed cascade weirs with 2.35 m in height and found surcharge
water level only 0.27 m higher than the existing condition in 2011.
Moreover, those weirs could maintain river water levels and increase
of those pumping performances during less river flow in 2013.
Abstract: Eight Etawah cross bred does were divided into two
groups based on body condition score (BCS). Group I (BSC 2, body
weight 25-30 kg; n = 4), and Group II (BSC 3, body weight, 35-40 kg, n=4). All does received intravaginal controlled internal drug
release devices (CIDR) for 10 days, and a prostaglandin F2α at 48 h before CIDR removal. Estrus detection was carried out using
vasectomized buck. Vaginal epithelium was taken to determine estrus cycle. Blood samples were taken every 3-6 hours, started from
moment of CIDR removal until the end of estrus. The results showed vaginal histological indicated estrus occurred at the hours of 25 to 60
and 30 to 70 post CIDR removal in BCS 2 and 3, respectively. Progesterone peak of BCS 2 and BCS 3 were 0.18±0.31 and
0.48±0.31 ng/mL on the hour 0 post CIDR removal. Estradiol -17ß
peak of each group was 53.25±35.08 and 89.91±92.84 pg/mL at 48
post CIDR removal. LH surge only occurred on BCS 3 groups, the LH concentrations were 9.9± 9.1; 4.5± 4.0; and 18.2± 9.1 ng/mL at
45, 48 and 51 hours post CIDR removal, respectively. It was concluded that the BCS had effects on vaginal histological changes
and LH surge.
Abstract: In this work, effects of catalysts (TiO2, and Nb2O5) were investigated on the hydrogen desorption of Mg(BH4)2. LiBH4 and MgCl2 with 2:1 molar ratio were mixed by using ball milling to prepare Mg(BH4)2. The desorption behaviors were measured by thermo-volumetric apparatus. The hydrogen desorption capacity of the mixed sample milled for 2 h was 4.78 wt% with a 2-step released. The first step occurred at 214 °C and the second step appeared at 374 °C. The addition of 16 wt% Nb2O5 decreased the desorption temperature in the second step about 66 °C and increased the hydrogen desorption capacity to 4.86 wt% hydrogen. The addition of TiO2 also improved the desorption temperature in the second step and the hydrogen desorption capacity. It decreased the desorption temperature about 71°C and showed a high amount of hydrogen, 5.27 wt%, released from the mixed sample. The hydrogen absorption after desorption of Mg(BH4)2 was also studied under 9.5 MPa and 350 °C for 12 h.
Abstract: Paddy being cultivated since about 10,000 years B.C in Ganga Valley in India, its production reached up to 99 million tons in the year 2012. BGA are of much ecological importance for maintaining the soil fertility and reclaiming the alkalinity. In present investigation attempts were made to identify the local cyanobacterial genera from the paddy fields, BGA application for green farming enabling the paddy to utilize more amount of nitrogen released and to examine its impact along with Urea upon growth and yield responses of the Paddy crop. It was observed that combined treatment of BGA with Urea proved better response in almost all growth parameters and yield attributes except number of tillers/ Plant and grains/ panicle as compared to application of either Urea or BGA alone. The Paddy growers should be encouraged to adopt BGA along with Urea as source of Nitrogen for Paddy cultivation.
Abstract: Bubble generation was observed using a high-speed
camera in subcooled flow boiling at low void fraction. Constant heat
flux was applied on one side of an upward rectangular channel to
make heated test channel. Water as a working fluid from high
subcooling to near saturation temperature was injected step by step to
investigate bubble behavior during void development. Experiments
were performed in two different pressures condition close to 2bar and
4bar. It was observed that in high subcooling when boiling was
commenced, bubble after nucleation departed its origin and slid
beside heated surface. In an observation window mean release
frequency of bubble fb,mean, nucleation site Ns and mean bubble
volume Vb,mean in each step of experiments were measured to
investigate wall vaporization rate. It was found that in proximity of
PNVG vaporization rate was increased significantly in compare with
condensation rate which remained in low value.
Abstract: The productivity of software development is one of the major concerns for project managers. Given the increasing complexity of the software being developed and the concomitant rise in the typical project size, the productivity has not consistently improved. By analyzing the latest release of ISBSG data repository with 4106 projects ever developed, we report on the factors found to significantly influence productivity, and present an original model for the estimation of productivity during project design. We further illustrate that software development productivity has experienced irregular variations between the years 1995 and 2005. Considering the factors significant to productivity, we found its variations are primarily caused by the variations of average team size for the development and the unbalanced use of the less productive development language 3GL.
Abstract: Software development is moving towards agility with use cases and scenarios being used for requirements stories. Estimates of software costs are becoming even more important than before as effects of delays is much larger in successive short releases context of agile development. Thus, this paper reports on the development of new linear use case based software cost estimation model applicable in the very early stages of software development being based on simple metric. Evaluation showed that accuracy of estimates varies between 43% and 55% of actual effort of historical test projects. These results outperformed those of wellknown models when applied in the same context. Further work is being carried out to improve the performance of the proposed model when considering the effect of non-functional requirements.
Abstract: A DC-to-DC converter for applications involving a
source with widely varying voltage conditions with loads requiring
constant voltage from full load down to no load is presented.
The switching regulator considered is a Buck converter with Pulse
Skipping Modulation control whereby pulses applied to the switch
are blocked or released on output voltage crossing a predetermined
value. Results of the study on the performance of regulator circuit
are presented. The regulator regulates over a wide input voltage range
with slightly higher ripple content and good transient response. Input
current spectrum indicates a good EMI performance with crowding
of components at low frequency range.
Abstract: Calcium [Ca2+] dynamics is studied as a potential form
of neuron excitability that can control many irregular processes like
metabolism, secretion etc. Ca2+ ion enters presynaptic terminal and
increases the synaptic strength and thus triggers the neurotransmitter
release. The modeling and analysis of calcium dynamics in neuron
cell becomes necessary for deeper understanding of the processes
involved. A mathematical model has been developed for cylindrical
shaped neuron cell by incorporating physiological parameters like
buffer, diffusion coefficient, and association rate. Appropriate initial
and boundary conditions have been framed. The closed form solution
has been developed in terms of modified Bessel function. A computer
program has been developed in MATLAB 7.11 for the whole
approach.
Abstract: Transdermal delivery of ondansetron hydrochloride (OdHCl) can prevent the problems encountered with oral ondansetron. In previously conducted studies, effect of amount of polyvinyl pyrrolidone, permeation enhancer and casting solvent on the physicochemical properties on OdHCl were investigated. It is feasible to develop ondansetron transdermal patch by using ethyl cellulose and polyvinyl pyrrolidone with dibutyl pthalate as plasticizer, however, the desired flux is not achieved. The primary aim of this study is to use dimethyl succinate (DMS) and propylene glycol that are not incorporated in previous studies to determine their effect on the physicochemical properties of an OdHCl transdermal patch using ethyl cellulose and polyvinyl pyrrolidone. This study also investigates the effect of permeation enhancer (eugenol and phosphatidylcholine) on the release of OdHCl. The results showed that propylene glycol is a more suitable plasticizer compared to DMS in the fabrication of OdHCl transdermal patch using ethyl cellulose and polyvinyl pyrrolidone as polymers. Propylene glycol containing patch has optimum drug content, thickness, moisture content and water absorption, tensile strength, and a better release profile than DMS. Eugenol and phosphatidylcholine can increase release of OdHCl from the patches. From the physicochemical result and permeation profile, a combination of 350mg of ethyl cellulose, 150mg polyvinyl pyrrolidone, 3% of total polymer weight of eugenol, and 40% of total polymer weight of propylene glycol is the most suitable formulation to develop an OdHCl patch. OdHCl release did not increase with increasing the percentage of plasticiser. DMS 4, PG 4, DMS 9, PG 9, DMS 14, and PG 14 gave better release profiles where using 300mg: 0mg, 300mg: 100mg, and 350mg: 150mg of EC: PVP. Thus, 40% of PG or DMS appeared to be the optimum amount of plasticiser when the above combination where EC: PVP was used. It was concluded from the study that a patch formulation containing 350mg EC, 150mg PVP, 40% PG and 3% eugenol is the best transdermal matrix patch compositions for the uniform and continuous release/permeation of OdHCl over an extended period. This patch design can be used for further pharmacokinetic and pharmacodynamic studies in suitable animal models.
Abstract: Wheat has a bimodal starch granule population and the dependency of the rate of enzymatic hydrolysis on particle size has been investigated. Ungelatinised wheaten starch granules were separated into two populations by sedimentation and decantation. Particle size was analysed by laser diffraction and morphological characteristics were viewed using SEM. The sedimentation technique though lengthy, gave satisfactory separation of the granules. Samples (10μm and original) were digested with a-amylase using a dialysis model. Granules of 10μm (p10μm. Moreover, the digestion rate was dependent on particle size whereby smaller granules produced higher rate of release. The methodology and results reported here can be used as a basis for further evaluations designed to delay the release of glucose during the digestion of native starches.
Abstract: As the fossil fuels kept on depleting, intense research in developing hydrogen (H2) as the alternative fuel has been done to cater our tremendous demand for fuel. The potential of H2 as the ultimate clean fuel differs with the fossil fuel that releases significant amounts of carbon dioxide (CO2) into the surrounding and leads to the global warming. The experimental work was carried out to study the production of H2 from palm kernel shell steam gasification at different variables such as heating rate, steam to biomass ratio and adsorbent to biomass ratio. Maximum H2 composition which is 61% (volume basis) was obtained at heating rate of 100oCmin-1, steam/biomass of 2:1 ratio, and adsorbent/biomass of 1:1 ratio. The commercial adsorbent had been modified by utilizing the alcoholwater mixture. Characteristics of both adsorbents were investigated and it is concluded that flowability and floodability of modified CaO is significantly improved.
Abstract: Understanding how airborne pathogens are
transported through hospital wards is essential for determining the
infection risk to patients and healthcare workers. This study utilizes
Computational Fluid Dynamics (CFD) simulations to explore
possible pathogen transport within a six-bed partitioned Nightingalestyle
hospital ward.
Grid independence of a ward model was addressed using the Grid
Convergence Index (GCI) from solutions obtained using three fullystructured
grids. Pathogens were simulated using source terms in
conjunction with a scalar transport equation and a RANS turbulence
model. Errors were found to be less than 4% in the calculation of air
velocities but an average of 13% was seen in the scalar field.
A parametric study of variations in the pathogen release point
illustrated that its distribution is strongly influenced by the local
velocity field and the degree of air mixing present.
Abstract: Most of the losses in a power system relate to
the distribution sector which always has been considered.
From the important factors which contribute to increase losses
in the distribution system is the existence of radioactive flows.
The most common way to compensate the radioactive power
in the system is the power to use parallel capacitors. In
addition to reducing the losses, the advantages of capacitor
placement are the reduction of the losses in the release peak of
network capacity and improving the voltage profile. The point
which should be considered in capacitor placement is the
optimal placement and specification of the amount of the
capacitor in order to maximize the advantages of capacitor
placement.
In this paper, a new technique has been offered for the
placement and the specification of the amount of the constant
capacitors in the radius distribution network on the basis of
Genetic Algorithm (GA). The existing optimal methods for
capacitor placement are mostly including those which reduce
the losses and voltage profile simultaneously. But the
retaliation cost and load changes have not been considered as
influential UN the target function .In this article, a holistic
approach has been considered for the optimal response to this
problem which includes all the parameters in the distribution
network: The price of the phase voltage and load changes. So,
a vast inquiry is required for all the possible responses. So, in
this article, we use Genetic Algorithm (GA) as the most
powerful method for optimal inquiry.
Abstract: In a competitive production environment, critical
decision making are based on data resulted by random sampling of
product units. Efficiency of these decisions depends on data quality
and also their reliability scale. This point leads to the necessity of a
reliable measurement system. Therefore, the conjecture process and
analysing the errors contributes to a measurement system known as
Measurement System Analysis (MSA). The aim of this research is on
determining the necessity and assurance of extensive development in
analysing measurement systems, particularly with the use of
Repeatability and Reproducibility Gages (GR&R) to improve
physical measurements. Nowadays in productive industries,
repeatability and reproducibility gages released so well but they are
not applicable as well as other measurement system analysis
methods. To get familiar with this method and gain a feedback in
improving measurement systems, this survey would be on
“ANOVA" method as the most widespread way of calculating
Repeatability and Reproducibility (R&R).
Abstract: In view of geological origin, formation of the shallow
gas reservoir of the Hangzhou Bay, northern Zhejiang Province,
eastern China, and original occurrence characteristics of the gassy
sand are analyzed. Generally, gassy sand in scale gas reservoirs is in
the state of residual moisture content and the approximate scope of
initial matric suction of sand ranges about from 0kPa to100kPa.
Results based on GDS triaxial tests show that the classical shear
strength formulas of unsaturated soil can not effectively describe basic
strength characteristics of gassy sand; the relationship between
apparent cohesion and matric suction of gassy sand agrees well with
the power function, which can reasonably be used to describe the
strength of gassy sand. In the stress path of gas release, shear strength
of gassy sand will increase and experimental results show the formula
proposed in this paper can effectively predict the strength increment.
When saturated strength indexes of the sand are used in engineering
design, moderate reduction should be considered.
Abstract: Combustion, emission and performance
characterization of a single cylinder diesel engine using methanol
diesel blends was carried out. The blends were 5% (v/v) methanol in
diesel (MD05) and 10% (v/v) methanol in diesel (MD10). The
problem of solubility of methanol and diesel was addressed by an
agitator placed inside the fuel tank to prevent phase separation. The
results indicated that total combustion duration was reduced by15.8%
for MD05 and 31.27% for MD10compared to the baseline data.
Ignition delay was increased with increasing methanol volume
fraction in the test fuel. Total cyclic heat release was reduced by
1.5% for MD05 and 6.7% for MD10 as compared to diesel baseline.
Emissions of carbon monoxide, hydrocarbons along with smoke were
reduced and that of nitrogen oxides were increased with rising
methanol contents in the test fuel. Full load brake thermal efficiency
was marginally reduced with increased methanol composition in the
blend.
Abstract: The aim of the present study was to evaluate the
mucoadhesion and the release of nicotinamide gel formulations using
in vitro methods. An agar plate technique was used to investigate the
adhesiveness of the gels whereas a diffusion apparatus was employed
to determine the release of nicotinamide from the gels. In this
respect, 10% w/w nicotinamide gels containing bioadhesive
polymers: Carbopol 934P (0.5-2% w/w), hydroxypropylmethyl
cellulose (HPMC) (4-10% w/w), sodium carboxymethyl cellulose
(SCMC) (4-6% w/w) and methylcellulose 4000 (MC) (3-5% w/w)
were prepared. The gel formulations had pH values in the range of
7.14 - 8.17, which were considered appropriate to oral mucosa
application. In general, the rank order of pH values appeared to be
SCMC > MC4000 > HPMC > Carbopol 934P. Types and
concentrations of polymers used somewhat affected the
adhesiveness. It was found that anionic polymers (Carbopol 934 and
SCMC) adhered more firmly to the agar plate than the neutral
polymers (HPMC and MC 4000). The formulation containing 0.5%
Carbopol 934P (F1) showed the highest release rate. With the
exception of the formulation F1, the neutral polymers tended to give
higher relate rates than the anionic polymers. For oral tissue
treatment, the optimum has to be balanced between the residence
time (adhesiveness) of the formulations and the release rate of the
drug. The formulations containing the anionic polymers: Carbopol
934P or SCMC possessed suitable physical properties (appearance,
pH and viscosity). In addition, for anionic polymer formulations,
justifiable mucoadhesive properties and reasonable release rates of
nicotinamide were achieved. Accordingly, these gel formulations
may be applied for the treatment of oral mucosal lesions.
Abstract: The most common cause of power transformer failures
is mechanical defect brought about by excessive vibration, which is
formed by the combination of multiples of a frequency of 120 Hz. In
this paper, the types of mechanical exciting forces applied to the
power transformer were classified, and the mechanical damage
mechanism of the power transformer was identified using the
vibration transfer route to the machine or structure. The general
effects of 120 Hz-vibration on the enclosure, bushing, Buchholz
relay, pressure release valve and tap changer of the transformer were
also examined.
Abstract: The relation between taxation states and foreign direct
investment has been studied for several perspectives and with states
of different levels of development. Usually it's only considered the
impact of tax level on the foreign direct investment volume. This
paper enhances this view by assuming that multinationals companies
(MNC) can use transfer prices systems and have got investment
timing flexibility. Thus, it evaluates the impact of the use of
international transfer pricing systems on the states- policy and on the
investment timing of the multinational companies. In uncertain
business environments (with periodical release of news), the
investment can increase if MNC detain investment delay options.
This paper shows how tax differentials can attract foreign direct
investments (FDI) and influence MNC behavior. The equilibrium is
set in a global environment where MNC can shift their profits
between states depending on the corporate tax rates. Assuming the
use of transfer pricing schemes, this paper confirms the relationship
between MNC behavior and the release of new business news.