Abstract: This document details the process of developing a
wireless device that captures the basic movements of the foot (plantar
flexion, dorsal flexion, abduction, adduction.), and the knee
movement (flexion). It implements a motion capture system by using
a hardware based on optical fiber sensors, due to the advantages in
terms of scope, noise immunity and speed of data transmission and
reception. The operating principle used by this system is the detection
and transmission of joint movement by mechanical elements and
their respective measurement by optical ones (in this case infrared).
Likewise, Visual Basic software is used for reception, analysis and
signal processing of data acquired by the device, generating a 3D
graphical representation in real time of each movement. The result is
a boot in charge of capturing the movement, a transmission module
(Implementing Xbee Technology) and a receiver module for
receiving information and sending it to the PC for their respective
processing.
The main idea with this device is to help on topics such as
bioengineering and medicine, by helping to improve the quality of
life and movement analysis.
Abstract: Machining through turning was carried out in a lathe
to study the chip formation of Multiphase Ferrite
(F-B-M) microalloyed steel. Taguchi orthogonal array was employed
to perform the machining. Continuous and discontinuous chips were
formed for different cutting parameters like speed, feed and depth of
cut. Optical and scanning electron microscope was employed to
identify the chip morphology.
Abstract: Superplastic deformation and high temperature load
relaxation behavior of coarse-grained iron aluminides with the
composition of Fe-28 at.% Al have been investigated. A series of load
relaxation and tensile tests were conducted at temperatures ranging
from 600 to 850oC. The flow curves obtained from load relaxation
tests were found to have a sigmoidal shape and to exhibit stress vs.
strain rate data in a very wide strain rate range from 10-7/s to 10-2/s.
Tensile tests have been conducted at various initial strain rates ranging
from 3×10-5/s to 1×10-2/s. Maximum elongation of ~500 % was
obtained at the initial strain rate of 3×10-5/s and the maximum strain
rate sensitivity was found to be 0.68 at 850oC in binary Fe-28Al alloy.
Microstructure observation through the optical microscopy (OM) and
the electron back-scattered diffraction (EBSD) technique has been
carried out on the deformed specimens and it has revealed the
evidences for grain boundary migration and grain refinement to occur
during superplastic deformation, suggesting the dynamic
recrystallization mechanism. The addition of Cr by the amount of 5
at.% appeared to deteriorate the superplasticity of the binary iron
aluminide. By applying the internal variable theory of structural
superplasticity, the addition of Cr has been revealed to lower the
contribution of the frictional resistance to dislocation glide during high
temperature deformation of the Fe3Al alloy.
Abstract: Skin color is an important visual cue for computer
vision systems involving human users. In this paper we combine skin
color and optical flow for detection and tracking of skin regions. We
apply these techniques to gesture recognition with encouraging
results. We propose a novel skin similarity measure. For grouping
detected skin regions we propose a novel skin region grouping
mechanism. The proposed techniques work with any number of skin
regions making them suitable for a multiuser scenario.
Abstract: Hydrogenated biodiesel is one of the most promising
renewable fuels. It has many advantages over conventional biodiesel,
including higher cetane number, higher heating value, lower
viscosity, and lower corrosiveness due to its absence of oxygen.
From previous work, Pd/TiO2 gave high conversion and selectivity in
hydrogenated biodiesel. In this work, the effect of biomass feedstocks
(i.e. beef fat, chicken fat, pork fat, and jatropha oil) on the production
of hydrogenated biodiesel over Pd/TiO2 has been studied. Biomass
feedstocks were analyzed by ICP-OES (inductively coupled plasma
optical emission spectrometry) to identify the content of impurities
(i.e. P, K, Ca, Na, and Mg). The deoxygenation catalyst, Pd/TiO2,
was prepared by incipient wetness impregnation (IWI) and tested in a
continuous flow packed-bed reactor at 500 psig, 325°C, H2/feed
molar ratio of 30, and LHSV of 4 h-1 for its catalytic activity and
selectivity in hydrodeoxygenation. All feedstocks gave high
selectivity in diesel specification range hydrocarbons and the main
hydrocarbons were n-pentadecane (n-C15) and n-heptadecane (n-
C17), resulting from the decarbonylation/decarboxylation reaction.
Intermediates such as oleic acid, stearic acid, palmitic acid, and esters
were also detected in minor amount. The conversion of triglycerides
in jatropha oil is higher than those of chicken fat, pork fat, and beef
fat, respectively. The higher concentration of metal impurities in
feedstock, the lower conversion of feedstock.
Abstract: In this work the design and characterization of an optoelectronic automated measurement system it is presented. The optoelectronic devices of this system are an optical transmitter, the optical components and the optical receiver, which were selected for a great precision of the system. The mechanical system allows free displacement of the components as well as the devices that generate the movement. The results, length and profile of the objects are display in Lab View.
Abstract: Wireless capsule Endoscopy (WCE) has rapidly
shown its wide applications in medical domain last ten years
thanks to its noninvasiveness for patients and support for thorough
inspection through a patient-s entire digestive system including
small intestine. However, one of the main barriers to efficient
clinical inspection procedure is that it requires large amount of
effort for clinicians to inspect huge data collected during the
examination, i.e., over 55,000 frames in video. In this paper, we
propose a method to compute meaningful motion changes of
WCE by analyzing the obtained video frames based on regional
optical flow estimations. The computed motion vectors are used to
remove duplicate video frames caused by WCE-s imaging nature,
such as repetitive forward-backward motions from peristaltic
movements. The motion vectors are derived by calculating
directional component vectors in four local regions. Our
experiments are performed on small intestine area, which is of
main interest to clinical experts when using WCEs, and our
experimental results show significant frame reductions comparing
with a simple frame-to-frame similarity-based image reduction
method.
Abstract: ZnO-SnO2 i.e. Zinc-Tin-Oxide (ZTO) thin films were
deposited on glass substrate with varying concentrations (ZnO:SnO2
- 100:0, 90:10, 70:30 and 50:50 wt.%) at room temperature by flash
evaporation technique. These deposited ZTO film were annealed at
450 0C in vacuum. These films were characterized to study the effect
of annealing on the structural, electrical, and optical properties.
Atomic force microscopy (AFM) and Scanning electron microscopy
(SEM) images manifest the surface morphology of these ZTO thin
films. The apparent growth of surface features revealed the formation
of nanostructure ZTO thin films. The small value of surface
roughness (root mean square RRMS) ensures the usefulness in
optical coatings. The sheet resistance was also found to be decreased
for both types of films with increasing concentration of SnO2. The
optical transmittance found to be decreased however blue shift has
been observed after annealing.
Abstract: In recent years Malaysia has included renewable
energy as an alternative fuel to help in diversifying the country-s
energy reliance on oil, natural gas, coal and hydropower with
biomass and solar energy gaining priority. The scope of this paper is
to look at the designing procedures and analysis of a solar thermal
parabolic trough concentrator by simulation utilizing meteorological
data in several parts of Malaysia. Parameters which include the
aperture area, the diameter of the receiver and the working fluid may
be varied to optimize the design. Aperture area is determined by
considering the width and the length of the concentrator whereas the
geometric concentration ratio (CR) is obtained by considering the
width and diameter of the receiver. Three types of working fluid are
investigated. Theoretically, concentration ratios can be very high in
the range of 10 to 40 000 depending on the optical elements used and
continuous tracking of the sun. However, a thorough analysis is
essential as discussed in this paper where optical precision and
thermal analysis must be carried out to evaluate the performance of
the parabolic trough concentrator as the theoretical CR is not the only
factor that should be considered.
Abstract: Although silicon photonic devices provide a significantly larger bandwidth and dissipate a substantially less power than the electronic devices, they suffer from a large size due to the fundamental diffraction limit and the weak optical response of Si. A potential solution is to exploit Si plasmonics, which may not only miniaturize the photonic device far beyond the diffraction limit, but also enhance the optical response in Si due to the electromagnetic field confinement. In this paper, we discuss and summarize the recently developed metal-insulator-Si-insulator-metal nanoplasmonic waveguide as well as various passive and active plasmonic components based on this waveguide, including coupler, bend, power splitter, ring resonator, MZI, modulator, detector, etc. All these plasmonic components are CMOS compatible and could be integrated with electronic and conventional dielectric photonic devices on the same SOI chip. More potential plasmonic devices as well as plasmonic nanocircuits with complex functionalities are also addressed.
Abstract: Corner detection and optical flow are common techniques for feature-based video stabilization. However, these algorithms are computationally expensive and should be performed at a reasonable rate. This paper presents an algorithm for discarding irrelevant feature points and maintaining them for future use so as to improve the computational cost. The algorithm starts by initializing a maintained set. The feature points in the maintained set are examined against its accuracy for modeling. Corner detection is required only when the feature points are insufficiently accurate for future modeling. Then, optical flows are computed from the maintained feature points toward the consecutive frame. After that, a motion model is estimated based on the simplified affine motion model and least square method, with outliers belonging to moving objects presented. Studentized residuals are used to eliminate such outliers. The model estimation and elimination processes repeat until no more outliers are identified. Finally, the entire algorithm repeats along the video sequence with the points remaining from the previous iteration used as the maintained set. As a practical application, an efficient video stabilization can be achieved by exploiting the computed motion models. Our study shows that the number of times corner detection needs to perform is greatly reduced, thus significantly improving the computational cost. Moreover, optical flow vectors are computed for only the maintained feature points, not for outliers, thus also reducing the computational cost. In addition, the feature points after reduction can sufficiently be used for background objects tracking as demonstrated in the simple video stabilizer based on our proposed algorithm.
Abstract: This work contains information about the influence low-level optical irradiation on sperm motility of sturgeon fish. On the basis of given and earlier received data the following conclusion has been made. Among the photophysical processes of a resonant and not resonant nature (oriented action of light; action of gradient forces; dipole-dipole interaction; termooptical processes), which are capable to cause the photobiological effects depended on such laserspecific characteristics as polarization and coherency, determining influence belongs to oriented action of light and dipole-dipole interactions among the processes studied in the present work.
Abstract: Internet infrastructures in most places of the world
have been supported by the advancement of optical fiber technology,
most notably wavelength division multiplexing (WDM) system.
Optical technology by means of WDM system has revolutionized
long distance data transport and has resulted in high data capacity,
cost reductions, extremely low bit error rate, and operational
simplification of the overall Internet infrastructure. This paper
analyses and compares the system impairments, which occur at data
transmission rates of 2.5Gb/s and 10 Gb/s per wavelength channel in
our proposed optical WDM system for Internet infrastructure in
Tanzania. The results show that the data transmission rate of 2.5 Gb/s
has minimum system impairments compared with a rate of 10 Gb/s
per wavelength channel, and achieves a sufficient system
performance to provide a good Internet access service.
Abstract: Gold coated silica core nanoparticles have an optical
response dictated by the plasmon resonance. The wavelength at
which the resonance occurs depends on the core and shell sizes,
allowing nanoshells to be tailored for particular applications. The
purposes of this study was to synthesize and use different
concentration of gold nanoshells as exogenous material for skin
tissue soldering and also to examine the effect of laser soldering
parameters on the properties of repaired skin. Two mixtures of
albumin solder and different concentration of gold nanoshells were
prepared. A full thickness incision of 2×20 mm2 was made on the
surface and after addition of mixtures it was irradiated by an 810nm
diode laser at different power densities. The changes of tensile
strength σt due to temperature rise, number of scan (Ns), and scan
velocity (Vs) were investigated. The results showed at constant laser
power density (I), σt of repaired incisions increases by increasing the
concentration of gold nanoshells, Ns and decreasing Vs. It is therefore
important to consider the trade off between the scan velocity and the
surface temperature for achieving an optimum operating condition. In
our case this corresponds to σt =1610 gr/cm2 at I~ 60 Wcm-2, T ~
65ºC, Ns =10 and Vs=0.2mms-1.
Abstract: Microparticles carrier systems made from naturally occurring polymers based on chitosan/casein system appears to be a promising carrier for the sustained release of orally and parenteral administered drugs. In the current study we followed a microencapsulation technique based aqueous coacervation method to prepare chitosan/casein microparticles of compositions 1:1, 1:2 and 1:5 incorporated with chloramphenicol. Glutaraldehyde was used as a chemical cross-linking agent. The microparticles were prepared by aerosol method and studied by optical microscopy, infrared spectroscopy, thermo gravimetric analysis, swelling studies and drug release studies at various pH. The percentage swelling of the polymers are found to be in the order pH 4 > pH 10 > pH 7 and the increase in casein composition decrease the swelling percentage. The drug release studies also follow the above order.
Abstract: One of the popular methods for recognition of facial
expressions such as happiness, sadness and surprise is based on
deformation of facial features. Motion vectors which show these
deformations can be specified by the optical flow. In this method, for
detecting emotions, the resulted set of motion vectors are compared
with standard deformation template that caused by facial expressions.
In this paper, a new method is introduced to compute the quantity of
likeness in order to make decision based on the importance of
obtained vectors from an optical flow approach. For finding the
vectors, one of the efficient optical flow method developed by
Gautama and VanHulle[17] is used. The suggested method has been
examined over Cohn-Kanade AU-Coded Facial Expression Database,
one of the most comprehensive collections of test images available.
The experimental results show that our method could correctly
recognize the facial expressions in 94% of case studies. The results
also show that only a few number of image frames (three frames) are
sufficient to detect facial expressions with rate of success of about
83.3%. This is a significant improvement over the available methods.
Abstract: We focus on the excitation and propagation properties
of surface plasmon polariton (SPP). We have developed a SPP
excitation device in combination with a grating structures fabricated
by using the scanning probe lithography. Perturbation approach was
used to investigate the coupling properties of SPP with a spatial
harmonic wave supported by a metallic grating. A phase shift grating
SPP coupler has been fabricated and the optical property was
evaluated by the Fraunhofer diffraction formula. We have been
experimentally confirmed the induced stop band by diffraction
measurement. We have also observed the wavenumber shift of the
resonance condition of SPP owing to effect of a phase shift.
Abstract: A tunable photonic microwave bandpass filter with
negative coefficient based on an electro-optic phase modulator (EOPM) and a variable polarization beamsplitter (VPBS) is
demonstrated. A two-tap microwave bandpass filter with one negative coefficient is presented. The chromatic dispersion and
optical coherence are not affected on this filter.
Abstract: the measurement of the angular distribution for the
elastic scattering of 16O, 14N and 12C on 27Al has been done at energy
1.75 MeV/nucleon. The optical potential code SPIVAL used in this
work to analyze the experimental results. A good agreement between
the experimental and theoretical results was obtained.
Abstract: The optical properties of InGaN/GaN laser diode based on quaternary alloys stopper and superlattice layers are numerically studied using ISE TCAD (Integrated System Engineering) simulation program. Improvements in laser optical performance have been achieved using quaternary alloy as superlattice layers in InGaN/GaN laser diodes. Lower threshold current of 18 mA and higher output power and slope efficiency of 22 mW and 1.6 W/A, respectively, at room temperature have been obtained. The laser structure with InAlGaN quaternary alloys as an electron blocking layer was found to provide better laser performance compared with the ternary AlxGa1-xN blocking layer.