Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: The effect of thermally induced stress on the modal
properties of highly elliptical core optical fibers is studied in this
work using a finite element method. The stress analysis is carried out
and anisotropic refractive index change is calculated using both the
conventional plane strain approximation and the generalized plane
strain approach. After considering the stress optical effect, the modal
analysis of the fiber is performed to obtain the solutions of
fundamental and higher order modes. The modal effective index,
modal birefringence, group effective index, group birefringence, and
dispersion of different modes of the fiber are presented. For
propagation properties, it can be seen that the results depend much on
the approach of stress analysis.
Abstract: A new and novel approach in medicine is the use of
cold plasma for various applications such as sterilization blood
coagulation and cancer cell treatment. In this paper a pin-to-hole
plasma jet suitable for biological applications is investigated and
characterized and the possibility and feasibility of cancer cell
treatment is evaluated. The characterization includes power
consumption via Lissajous method, thermal behavior of plasma using
Infra-red camera as a novel method, Optical Emission Spectroscopy
(OES) to determine the species that are generated. Treatment of
leukemia cancer cells is also implemented and MTT assay is used to
evaluate viability.
Abstract: Films of pure tin oxide SnO2 and in presence of
antimony atoms (SnO2-Sb) deposited onto glass substrates have
shown a sufficiently high energy gap to be transparent in the visible
region, a high electrical mobility and a carrier concentration which
displays a good electrical conductivity [1]. In this work, the effects of
polycrystalline silicon substrate on the optical properties of pure and
Sb doped tin oxide is investigated.
We used the APCVD (atmospheric pressure chemical vapour
deposition) technique, which is a low-cost and simple technique,
under nitrogen ambient, for growing this material. A series of SnO2
and SnO2-Sb have been deposited onto polycrystalline silicon
substrates with different contents of antimony atoms at the same
conditions of deposition (substrate temperature, flow oxygen,
duration and nitrogen atmosphere of the reactor). The effect of the
substrate in terms of morphology and nonlinear optical properties,
mainly the reflectance, was studied. The reflectance intensity of the
device, compared to the reflectance of tin oxide films deposited
directly on glass substrate, is clearly reduced on the overall
wavelength range. It is obvious that the roughness of the poly-c
silicon plays an important role by improving the reflectance and
hence the optical parameters.
A clear shift in the minimum of the reflectance upon doping level
is observed. This minimum corresponds to strong free carrier
absorption, resulting in different plasma frequency. This effect is
followed by an increase in the reflectance depending of the antimony
doping. Applying the extended Drude theory to the combining
optical and electrical obtained results these effects are discussed.
Abstract: Optical Character Recognition (OCR) is a very old and of great interest in pattern recognition field. In this paper we introduce a very powerful approach to recognize Persian text. We have used morphological operators, especially Hit/Miss operator to descript each sub-word and by using a template matching approach we have tried to classify generated description. We used just one font in two different sizes to verify our approach. We achieved a very good rate, up to 99.9%.
Abstract: This paper reports on the theoretical performance
analysis of the 1.3 μm In0.42Ga0.58As /In0.26Ga0.74As multiple quantum
well (MQW) vertical cavity surface emitting laser (VCSEL) on the
ternary In0.31Ga0.69As substrate. The output power of 2.2 mW has
been obtained at room temperature for 7.5 mA injection current. The
material gain has been estimated to be ~3156 cm-1 at room
temperature with the injection carrier concentration of 2×1017 cm-3.
The modulation bandwidth of this laser is measured to be 9.34 GHz
at room temperature for the biasing current of 2 mA above the
threshold value. The outcomes reveal that the proposed InGaAsbased
MQW laser is the promising one for optical communication
system.
Abstract: This paper presented a MATLAB-based system named Smart Access Network Testing, Analyzing and Database (SANTAD), purposely for in-service transmission surveillance and self restoration against fiber fault in fiber-to-the-home (FTTH) access network. The developed program will be installed with optical line terminal (OLT) at central office (CO) to monitor the status and detect any fiber fault that occurs in FTTH downwardly from CO towards residential customer locations. SANTAD is interfaced with optical time domain reflectometer (OTDR) to accumulate every network testing result to be displayed on a single computer screen for further analysis. This program will identify and present the parameters of each optical fiber line such as the line's status either in working or nonworking condition, magnitude of decreasing at each point, failure location, and other details as shown in the OTDR's screen. The failure status will be delivered to field engineers for promptly actions, meanwhile the failure line will be diverted to protection line to ensure the traffic flow continuously. This approach has a bright prospect to improve the survivability and reliability as well as increase the efficiency and monitoring capabilities in FTTH.
Abstract: This paper evaluate the multilevel modulation for
different techniques such as amplitude shift keying (M-ASK), MASK,
differential phase shift keying (M-ASK-Bipolar), Quaternary
Amplitude Shift Keying (QASK) and Quaternary Polarization-ASK
(QPol-ASK) at a total bit rate of 107 Gbps. The aim is to find a costeffective
very high speed transport solution. Numerical investigation
was performed using Monte Carlo simulations. The obtained results
indicate that some modulation formats can be operated at 100Gbps
in optical communication systems with low implementation effort
and high spectral efficiency.
Abstract: This paper presented a new approach for centralized
monitoring and self-protected against fiber fault in fiber-to-the-home
(FTTH) access network by using Smart Access Network Testing,
Analyzing and Database (SANTAD). SANTAD will be installed
with optical line terminal (OLT) at central office (CO) for in-service
transmission surveillance and fiber fault localization within FTTH
with point-to-multipoint (P2MP) configuration downwardly from CO
towards customer residential locations based on the graphical user
interface (GUI) processing capabilities of MATLAB software.
SANTAD is able to detect any fiber fault as well as identify the
failure location in the network system. SANTAD enable the status of
each optical network unit (ONU) connected line is displayed onto
one screen with capability to configure the attenuation and detect the
failure simultaneously. The analysis results and information will be
delivered to the field engineer for promptly actions, meanwhile the
failure line will be diverted to protection line to ensure the traffic
flow continuously. This approach has a bright prospect to improve
the survivability and reliability as well as increase the efficiency and
monitoring capabilities in FTTH.
Abstract: The motivation of this work was to find a suitable 3D
scanner for human body parts digitalization in the field of prosthetics
and orthotics. The main project objective is to compare the three
hand-held portable scanners (two optical and one laser) and two
optical tripod scanners. The comparison was made with respect of
scanning detail, simplicity of operation and ability to scan directly on
the human body. Testing was carried out on a plaster cast of the
upper limb and directly on a few volunteers. The objective monitored
parameters were time of digitizing and post-processing of 3D data
and resulting visual data quality. Subjectively, it was considered level
of usage and handling of the scanner. The new tripod was developed
to improve the face scanning conditions. The results provide an
overview of the suitability of different types of scanners.
Abstract: In high powered dense wavelength division
multiplexed (WDM) systems with low chromatic dispersion,
four-wave mixing (FWM) can prove to be a major source of noise.
The MultiCanonical Monte Carlo Method (MCMC) and the Split
Step Fourier Method (SSFM) are combined to accurately evaluate the
probability density function of the decision variable of a receiver,
limited by FWM. The combination of the two methods leads to more
accurate results, and offers the possibility of adding other optical
noises such as the Amplified Spontaneous Emission (ASE) noise.
Abstract: We demonstrate a 40Gbps downstream PON
transmission based on PM-QPSK modulation using commercial DFB
lasers without optical amplifier in the ODN, obtaining 40dB power
budget. We discuss this solution within NG-PON2 architectures.
Abstract: In order to implement flexibility as well as survivable
capacities over passive optical network (PON), a new automatic
random fault-recovery mechanism with array-waveguide-grating
based (AWG-based) optical switch (OSW) is presented. Firstly,
wavelength-division-multiplexing and optical code-division
multiple-access (WDM/OCDMA) scheme are configured to meet the
various geographical locations requirement between optical network
unit (ONU) and optical line terminal (OLT). The AWG-base optical
switch is designed and viewed as central star-mesh topology to
prohibit/decrease the duplicated redundant elements such as fiber and
transceiver as well. Hence, by simple monitoring and routing switch
algorithm, random fault-recovery capacity is achieved over
bi-directional (up/downstream) WDM/OCDMA scheme. When error
of distribution fiber (DF) takes place or bit-error-rate (BER) is higher
than 10-9 requirement, the primary/slave AWG-based OSW are
adjusted and controlled dynamically to restore the affected ONU
groups via the other working DFs immediately.
Abstract: To establish optical communication between any two
satellites, the transmitter satellite must track the beacon of the
receiver satellite and point the information optical beam in its
direction. Optical tracking and pointing systems for free space suffer
during tracking from high-amplitude vibration because of
background radiation from interstellar objects such as the Sun, Moon,
Earth, and stars in the tracking field of view or the mechanical
impact from satellite internal and external sources. The vibrations of
beam pointing increase the bit error rate and jam communication
between the two satellites. One way to overcome this problem is the
use of very small transmitter beam divergence angles of too narrow
divergence angle is that the transmitter beam may sometimes miss
the receiver satellite, due to pointing vibrations. In this paper we
propose the use of genetic algorithm to optimize the BER as function
of transmitter optics aperture.
Abstract: The purpose of this study is to present a non invasive
method for the marginal adaptation evaluation in class V composite
restorations. Standardized class V cavities, prepared in human
extracted teeth, were filled with Premise (Kerr) composite. The
specimens were thermo cycled. The interfaces were examined by
Optical Coherence Tomography method (OCT) combined with the
confocal microscopy and fluorescence. The optical configuration
uses two single mode directional couplers with a superluminiscent
diode as the source at 1300 nm. The scanning procedure is similar to
that used in any confocal microscope, where the fast scanning is enface
(line rate) and the depth scanning is much slower (at the frame
rate). Gaps at the interfaces as well as inside the composite resin
materials were identified. OCT has numerous advantages which
justify its use in vivo as well as in vitro in comparison with
conventional techniques.
Abstract: The Block Sorting problem is to sort a given
permutation moving blocks. A block is defined as a substring
of the given permutation, which is also a substring of the
identity permutation. Block Sorting has been proved to be
NP-Hard. Until now two different 2-Approximation algorithms
have been presented for block sorting. These are the best known
algorithms for Block Sorting till date. In this work we present
a different characterization of Block Sorting in terms of a
transposition cycle graph. Then we suggest a heuristic,
which we show to exhibit a 2-approximation performance
guarantee for most permutations.
Abstract: A subcarrier - spectral amplitude coding optical code
division multiple access system using the Khazani-Syed code with
Complementary subtraction detection technique is proposed. The
proposed system has been analyzed by taking into account the effects
of phase-induced intensity noise, shot noise, thermal noise and intermodulation
distortion noise. The performance of the system has been
compared with the spectral amplitude coding optical code division
multiple access system using the Hadamard code and the Modified
Quadratic Congruence code. The analysis shows that the proposed
system can eliminate the multiple access interference using the
Complementary subtraction detection technique, and hence improve
the overall system performance.
Abstract: Proximate (moisture, protein, total fat, total ash) and mineral (K, P, Na, Mg, Ca, Zn, Fe, Cu and Mn) composition of chicken giblets (heart, liver and gizzard) were investigated. Phosphorous content, as well as proximate composition, were determined according to recommended ISO methods. The content of all elements, except phosphorus, of the giblets tissues were determined using inductively coupled plasma-optical emission spectrometry (ICP-OES), after dry ashing mineralization. Regarding proximate composition heart was the highest in total fat content, and the lowest in protein content. Liver was the highest in protein and total ash content, while gizzard was the highest in moisture and the lowest in total fat content. Regarding mineral composition liver was the highest for K, P, Ca, Mg, Fe, Zn, Cu, and Mn, while heart was the highest for Na content. The contents of almost all investigated minerals in analysed giblets tissues of chickens from Vojvodina were similar to values reported in the literature, i.e. in national food composition databases of other countries.
Abstract: ZnS nanoparticles of different size have been
synthesized using a colloidal particles method. Zns nanoparticles
prepared with capping agent (mercaptoethanol) then were
characterized using X-ray diffraction (XRD) and UV-Vis
spectroscopy. The particle size of the nanoparticles calculated from
the XRD patterns has been found in the range 1.85-2.44nm.
Absorption spectra have been obtained using UV-Vis
spectrophotometer to find the optical band gap and the obtained
values have been founded to being range 3.83-4.59eV. It was also
found that energy band gap increase with the increase in molar
capping agent solution.
Abstract: Two seperate experiments by barley and alfalfa were
conducted to a 2×8 factorial completely randomised design, with four
replicates. Factors were inoculation (M) with Gomus mosseae or uninoculation
(M0) and seven levels of contaminants (Co, Cd, Pb and
combinations) plus an uncontaminated control treatment (C). Heavy
metals in plant tissues and soil were quantified by Inductively
Coupled Plasma Optical Emission Spectrometer (ICP-OES) (Variant-
Liberty 150AX Turbo). Phytoextraction coefficient of contaminants
calculated by concentration of heavy metals in the shoot (mgkg-1) /
concentration of heavy metals in soil (mgkg-1). In the barley, the
highest rate of phytoextraction coefficient of Pb, Cd and Co was in
M0Pb, M0PbCoCd and MCo, respectively (P