Abstract: In this paper, we proposed a novel SCR (Silicon Controlled
Rectifier) - based ESD (Electrostatic Discharge) protection device for I/O
and power clamp. The proposed device has a higher holding voltage
characteristic than conventional SCR. These characteristics enable to have
latch-up immunity under normal operating conditions as well as superior full
chip ESD protection. The proposed device was analyzed to figure out
electrical characteristics and tolerance robustness in term of individual
design parameters (D1, D2, D3). They are investigated by using the
Synopsys TCAD simulator. As a result of simulation, holding voltage
increased with different design parameters. The holding voltage of the
proposed device changes from 3.3V to 7.9V. Also, N-Stack structure ESD
device with the high holding voltage is proposed. In the simulation results,
2-stack has holding voltage of 6.8V and 3-stack has holding voltage of
10.5V. The simulation results show that holding voltage of stacking
structure can be larger than the operation voltage of high-voltage
application.
Abstract: In the present study, response surface methodology has been used to optimize turn-assisted deep cold rolling process of AISI 4140 steel. A regression model is developed to predict surface hardness and surface roughness using response surface methodology and central composite design. In the development of predictive model, deep cold rolling force, ball diameter, initial roughness of the workpiece, and number of tool passes are considered as model variables. The rolling force and the ball diameter are the significant factors on the surface hardness and ball diameter and numbers of tool passes are found to be significant for surface roughness. The predicted surface hardness and surface roughness values and the subsequent verification experiments under the optimal operating conditions confirmed the validity of the predicted model. The absolute average error between the experimental and predicted values at the optimal combination of parameter settings for surface hardness and surface roughness is calculated as 0.16% and 1.58% respectively. Using the optimal processing parameters, the surface hardness is improved from 225 to 306 HV, which resulted in an increase in the near surface hardness by about 36% and the surface roughness is improved from 4.84µm to 0.252 µm, which resulted in decrease in the surface roughness by about 95%. The depth of compression is found to be more than 300µm from the microstructure analysis and this is in correlation with the results obtained from the microhardness measurements. Taylor hobson talysurf tester, micro vickers hardness tester, optical microscopy and X-ray diffractometer are used to characterize the modified surface layer.
Abstract: In this study, we demonstrate the production of natural gas hydrates from permeable marine sediments with simultaneous mechanisms for methane recovery and methane-air or methane-air/carbon dioxide replacement. The simultaneous melting happens until the chemical potentials become equal in both phases as natural gas hydrate depletion continues and self-regulated methane-air replacement occurs over an arbitrary point. We observed certain point between dissociation and replacement mechanisms in the natural gas hydrate reservoir, and we call this boundary as critical methane concentration. By the way, when carbon dioxide was added, the process of chemical exchange of methane by air/carbon dioxide was observed in the natural gas hydrate. The suggested process will operate well for most global natural gas hydrate reservoirs, regardless of the operating conditions or geometrical constraints.
Abstract: In a practical power system, the power plants are not
located at the same distance from the center of loads and their fuel
costs are different. Also, under normal operating conditions, the
generation capacity is more than the total load demand and losses.
Thus, there are many options for scheduling generation. In an
interconnected power system, the objective is to find the real and
reactive power scheduling of each power plant in such a way as to
minimize the operating cost. This means that the generator’s real and
reactive powers are allowed to vary within certain limits so as to meet
a particular load demand with minimum fuel cost. This is called
optimal power flow problem. In this paper, Economic Load Dispatch
(ELD) of real power generation is considered. Economic Load
Dispatch (ELD) is the scheduling of generators to minimize total
operating cost of generator units subjected to equality constraint of
power balance within the minimum and maximum operating limits of
the generating units. In this paper, genetic algorithms are considered.
ELD solutions are found by solving the conventional load flow
equations while at the same time minimizing the fuel costs.
Abstract: Advanced treatments such as forward osmosis (FO)
can be used to separate or reject nutrients from secondary treated
effluents. Forward osmosis uses the chemical potential across the
membrane, which is the osmotic pressure gradient, to induce water to
flow through the membrane from a feed solution (FS) into a draw
solution (DS). The performance of FO is affected by the membrane
characteristics, composition of the FS and DS, and operating
conditions. The aim of this study was to investigate the optimum
velocity and temperature for nutrient rejection and water flux
performance in FO treatments. MgCl2 was used as the DS in the FO
process. The results showed that higher cross flow velocities yielded
higher water fluxes. High rejection of nutrients was achieved by using
a moderate cross flow velocity at 0.25 m/s. Nutrient rejection was
insensitive to temperature variation, whereas water flux was
significantly impacted by it. A temperature of 25°C was found to be
good for nutrient rejection.
Abstract: Hydrothermal liquefaction (HTL) is a technique for obtaining clean biofuel from biomass in the presence of heat and pressure in an aqueous medium which leads to a decomposition of this biomass to the formation of various products. A role of operating conditions is essential for the bio-oil and other products’ yield and also quality of the products. The effects of these parameters were investigated in regards to the composition and yield of the products. Chlorellaceae microalgae were tested under different HTL conditions to clarify suitable conditions for extracting bio-oil together with value-added co-products. Firstly, different microalgae loading rates (5-30%) were tested and found that this parameter has not much significant to product yield. Therefore, 10% microalgae loading rate was selected as a proper economical solution for conditioned schedule at 250oC and 30 min-reaction time. Next, a range of temperature (210-290oC) was applied to verify the effects of each parameter by keeping the reaction time constant at 30 min. The results showed no linkage with the increase of the reaction temperature and some reactions occurred that lead to different product yields. Moreover, some nutrients found in the aqueous product are possible to be utilized for nutrient recovery.
Abstract: The distribution of a single global clock across a chip
has become the major design bottleneck for high performance VLSI
systems owing to the power dissipation, process variability and multicycle
cross-chip signaling. A Network-on-Chip (NoC) architecture
partitioned into several synchronous blocks has become a promising
approach for attaining fine-grain power management at the system
level. In a NoC architecture the communication between the blocks is
handled asynchronously. To interface these blocks on a chip
operating at different frequencies, an asynchronous FIFO interface is
inevitable. However, these asynchronous FIFOs are not required if
adjacent blocks belong to the same clock domain. In this paper, we
have designed and analyzed a 16-bit asynchronous micropipelined
FIFO of depth four, with the awareness of place and route on an
FPGA device. We have used a commercially available Spartan 3
device and designed a high speed implementation of the
asynchronous 4-phase micropipeline. The asynchronous FIFO
implemented on the FPGA device shows 76 Mb/s throughput and a
handshake cycle of 109 ns for write and 101.3 ns for read at the
simulation under the worst case operating conditions (voltage =
0.95V) on a working chip at the room temperature.
Abstract: Fixed-geometry hydrodynamic journal bearings are
one of the best supporting systems for several applications of rotating
machinery. Cylindrical journal bearings present excellent loadcarrying
capacity and low manufacturing costs, but they are subjected
to the oil-film instability at high speeds. An attempt of overcoming
this instability problem has been the development of non-circular
journal bearings. This work deals with an analysis of oil-lubricated
elliptical journal bearings using the finite element method. Steadystate
and dynamic performance characteristics of elliptical bearings
are rendered by zeroth- and first-order lubrication equations obtained
through a linearized perturbation method applied on the classical
Reynolds equation. Four-node isoparametric rectangular finite
elements are employed to model the bearing thin film flow. Curves of
elliptical bearing load capacity and dynamic force coefficients are
rendered at several operating conditions. The results presented in this
work demonstrate the influence of the bearing ellipticity on its
performance at different loading conditions.
Abstract: A three-dimensional numerical model of
thermoelectric generator (TEG) modules attached to a large chimney
plate is proposed and solved numerically using a control volume based
finite difference formulation. The TEG module consists of a
thermoelectric generator, an elliptical pin-fin heat sink, and a cold
plate for water cooling. In the chimney, the temperature of flue gases is
450-650K. Although the TEG hot-side temperature and thus the
electric power output can be increased by inserting an elliptical pin-fin
heat sink into the chimney tunnel to increase the heat transfer area, the
pin fin heat sink would cause extra pumping power at the same time.
The main purpose of this study is to analyze the effects of geometrical
parameters on the electric power output and chimney pressure drop
characteristics. The effects of different operating conditions, including
various inlet velocities (Vin= 1, 3, 5 m/s), inlet temperatures (Tgas = 450,
550, 650K) and different fin height (0 to 150 mm) are discussed in
detail. The predicted numerical data for the power vs. current (P-I)
curve are in good agreement (within 11%) with the experimental data.
Abstract: This paper shortly describes various types of biomass
and a growing number of facilities utilizing the biomass in the Czech
Republic. The considerable part of this paper deals with energy
parameters of the most frequently used types of biomass and results
of their gasification testing. Sixteen most used "Czech" woody plants
and grasses were selected; raw, element and biochemical analyses
were performed and basic calorimetric values, ash composition, and
ash characteristic temperatures were identified. Later, each biofuel
was tested in a fluidized bed gasifier. The essential part of this paper
provides results of the gasification of selected biomass types.
Operating conditions are described in detail with a focus on
individual fuels properties. Gas composition and impurities content
are also identified. In terms of operating conditions and gas quality,
the essential difference occurred mainly between woody plants and
grasses. The woody plants were evaluated as more suitable fuels for
fluidized bed gasifiers. Testing results significantly help with a
decision-making process regarding suitability of energy plants for
growing and with a selection of optimal biomass-treatment
technology.
Abstract: In this paper, we discuss the performance of applying
hybrid spiral dynamic bacterial chemotaxis (HSDBC) optimisation
algorithm on an intelligent controller for a differential drive robot. A
unicycle class of differential drive robot is utilised to serve as a basis
application to evaluate the performance of the HSDBC algorithm. A
hybrid fuzzy logic controller is developed and implemented for the
unicycle robot to follow a predefined trajectory. Trajectories of
various frictional profiles and levels were simulated to evaluate the
performance of the robot at different operating conditions. Controller
gains and scaling factors were optimised using HSDBC and the
performance is evaluated in comparison to previously adopted
optimisation algorithms. The HSDBC has proven its feasibility in
achieving a faster convergence toward the optimal gains and resulted
in a superior performance.
Abstract: Diffusion stills have been effective in water
desalination. The present work represents a model of the distillation
process by using vertical single-effect diffusion stills. A semianalytical
model has been developed to model the process. A
software computer code using Engineering Equation Solver EES
software has been developed to solve the equations of the developed
model. An experimental setup has been constructed, and used for the
validation of the model. The model is also validated against former
literature results. The results obtained from the present experimental
test rig, and the data from the literature, have been compared with the
results of the code to find its best range of validity. In addition, a
parametric analysis of the system has been developed using the
model to determine the effect of operating conditions on the system's
performance. The dominant parameters that affect the productivity of
the still are the hot plate temperature that ranges from (55- 90°C) and
feed flow rate in range of (0.00694-0.0211 kg/m2-s).
Abstract: Presently, engine cooling pump is driven by toothed
belt. Therefore, the pump speed is dependent on engine speed which
varies their output. At normal engine operating conditions (Higher
RPM and low load, Higher RPM and high load), mechanical water
pumps in existing engines are inevitably oversized and so the use of
an electric water pump together with state-of-the-art thermal
management of the combustion engine has measurable advantages.
Demand-driven cooling, particularly in the cold-start phase, saves
fuel (approx 3 percent) and leads to a corresponding reduction in
emissions. The lack of dependence on a mechanical drive also results
in considerable flexibility in component packaging within the engine
compartment. This paper describes the testing and comparison of
existing mechanical water pump with that of the electric water pump.
When the existing mechanical water pump is replaced with the new
electric water pump the percentage gain in system efficiency is also
discussed.
Abstract: This paper presents the design analysis of saddle
support of a horizontal pressure vessel. Since saddle have the vital
role to support the pressure vessel and to maintain its stability, it
should be designed in such a way that it can afford the vessel load
and internal pressure of the vessel due to liquid contained in the
vessel. A model of horizontal pressure vessel and saddle support is
created in ANSYS. Stresses are calculated using mathematical
approach and ANSYS software. The analysis reveals the zone of high
localized stress at the junction part of the pressure vessel and saddle
support due to operating conditions. The results obtained by both the
methods are compared with allowable stress value for safe designing.
Abstract: Mass flow measurement is the basis of most technoeconomic
formulations in the chemical industry. This calls for
reliable and accurate detection of mass flow. Flow measurement
laboratory experiments were conducted using various instruments.
These consisted of orifice plates, various sized rotameters, wet gas
meter and soap bubble meter. This work was aimed at evaluating
appropriate operating conditions and accuracy of the aforementioned
devices. The experimental data collected were compared to
theoretical predictions from Bernoulli’s equation and calibration
curves supplied by the instrument’s manufacturers. The results
obtained showed that rotameters were more reliable for measuring
high and low flow rates; while soap-bubble meters and wet-gas
meters were found to be suitable for measuring low flow rates. The
laboratory procedures and findings of the actual work can assist
engineering students and professionals in conducting their flow
measurement laboratory test work.
Abstract: This paper aims at finding a suitable neural network
for monitoring congestion level in electrical power systems. In this
paper, the input data has been framed properly to meet the target
objective through supervised learning mechanism by defining normal
and abnormal operating conditions for the system under study. The
congestion level, expressed as line congestion index (LCI), is
evaluated for each operating condition and is presented to the NN
along with the bus voltages to represent the input and target data.
Once, the training goes successful, the NN learns how to deal with a
set of newly presented data through validation and testing
mechanism. The crux of the results presented in this paper rests on
performance comparison of a multi-layered feed forward neural
network with eleven types of back propagation techniques so as to
evolve the best training criteria. The proposed methodology has been
tested on the standard IEEE-14 bus test system with the support of
MATLAB based NN toolbox. The results presented in this paper
signify that the Levenberg-Marquardt backpropagation algorithm
gives best training performance of all the eleven cases considered in
this paper, thus validating the proposed methodology.
Abstract: Most flexible rotors can be considered as beam-like
structures. In many cases, rotors are modeled as one-dimensional
bodies, made basically of beam-like shafts with rigid bodies attached
to them. This approach is typical of rotor dynamics, both analytical
and numerical, and several rotor dynamic codes, based on the finite
element method, follow this trend. In this paper, a finite element
model based on Timoshenko beam elements is utilized to analyze the
lateral dynamic behavior of a certain rotor-bearing system in
operating conditions.
Abstract: DC-DC converters are widely used as reliable power source for many industrial and military applications, computers and electronic devices. Several control methods were developed for DC-DC converters control mostly with asymptotic convergence. Synergetic control (SC) is a proven robust control approach and will be used here in a so called terminal scheme to achieve finite time convergence. Lyapounov synthesis is adopted to assure controlled system stability. Furthermore particle swarm optimization (PSO) algorithm, based on an integral time absolute of error (ITAE) criterion will be used to optimize controller parameters. Simulation of terminal synergetic control of a DC-DC converter is carried out for different operating conditions and results are compared to classic synergetic control performance, that which demonstrate the effectiveness and feasibility of the proposed control method.
Abstract: Effects of insertion of coiled wire in juxtaposition with twisted tapes on heat transfer rate and solar radiation without disturbing the flow inside the riser tubes in a solar flat plate collector is experimentally reconnoitered in this present work. The wire coil used as a turbulator is placed inside the riser tube while the twisted tape is inserted into the wire coil to create a continuous swirling flow along the tube wall. The results of the heat transfer have been compared well with the available results. The heat transfer rate in the collector has been found to be increased by 18% to 70%. Solar water heaters having inserts in the flow tubes perform better than the conventional plain ones. It has been observed that heat losses are reduced consequently increasing the thermal performance about 30% over the plain water heaters under the same operating conditions. The effect of twisted tape with wire coils, flow Reynolds number, and the intensity of solar radiation on the thermal performance of the solar water heater has been presented. Effects of insertion of coiled wire in juxtaposition with twisted tapes on heat transfer rate and solar radiation without disturbing the flow inside the riser tubes in a solar flat plate collector is experimentally reconnoitered in this present work. The wire coil used as a turbulator is placed inside the riser tube while the twisted tape is inserted into the wire coil to create a continuous swirling flow along the tube wall. The results of the heat transfer have been compared well with the available results. The heat transfer rate in the collector has been found to be increased by 18% to 70%. Solar water heaters having inserts in the flow tubes perform better than the conventional plain ones. It has been observed that heat losses are reduced consequently increasing the thermal performance about 30% over the plain water heaters under the same operating conditions. The effect of twisted tape with wire coils, flow Reynolds number, and the intensity of solar radiation on the thermal performance of the solar water heater has been presented.
Abstract: The hydrolysis of lactose using β-galactosidase is one of the most promising biotechnological applications, which has wide range of potential applications in food processing industries. However, due to intracellular location of the yeast enzyme, and expensive extraction methods, the industrial applications of enzymatic hydrolysis processes are being hampered. The use of permeabilization technique can help to overcome the problems associated with enzyme extraction and purification of yeast cells and to develop the economically viable process for the utilization of whole cell biocatalysts in food industries. In the present investigation, standardization of permeabilization process of novel yeast isolate was carried out using a statistical model approach known as Response Surface Methodology (RSM) to achieve maximal b-galactosidase activity. The optimum operating conditions for permeabilization process for optimal β-galactosidase activity obtained by RSM were 1:1 ratio of toluene (25%, v/v) and ethanol (50%, v/v), 25.0 oC temperature and treatment time of 12 min, which displayed enzyme activity of 1.71 IU /mg DW.