Abstract: The paper analyzes the large power transformer unit regimes, indicating the criteria for the management of the voltage operating conditions, as well as the change in the operating conditions with the load connected to the secondary winding of the transformer unit. Further, the paper presents the software application for the evaluation of the transformer unit operation under different conditions. The software application was developed by means of virtual instrumentation.
Abstract: In this paper, we consider Wiener nonlinear model for solid oxide fuel cell (SOFC). The Wiener model of the SOFC consists of a linear dynamic block and a static output non-linearity followed by the block, in which linear part is approximated by state-space model and the nonlinear part is identified by a polynomial form. To control the SOFC system, we have to consider various view points such as operating conditions, another constraint conditions, change of load current and so on. A change of load current is the significant one of these for good performance of the SOFC system. In order to keep the constant stack terminal voltage by changing load current, the nonlinear model predictive control (MPC) is proposed in this paper. After primary control method is designed to guarantee the fuel utilization as a proper constant, a nonlinear model predictive control based on the Wiener model is developed to control the stack terminal voltage of the SOFC system. Simulation results verify the possibility of the proposed Wiener model and MPC method to control of SOFC system.
Abstract: A rigorous two-dimensional model is developed for simulating the operation of a less-investigated type steam reformer having a considerably lower operating Reynolds number, higher tube diameter, and non-availability of extra steam in the feed compared with conventional steam reformers. Simulation results show that reasonable predictions can only be achieved when certain correlations for wall to fluid heat transfer equations are applied. Due to severe operating conditions, in all cases, strong radial temperature gradients inside the reformer tubes have been found. Furthermore, the results show how a certain catalyst loading profile will affect the operation of the reformer.
Abstract: Cooktop burners are widely used nowadays. In
cooktop burner design, nozzle efficiency and greenhouse
gas(GHG) emissions mainly depend on heat transfer from the
premixed flame to the impinging surface. This is a complicated
issue depending on the individual and combined effects of various
input combustion variables. Optimal operating conditions for
sustainable burner design were rarely addressed, especially in the
case of multiple slot-jet burners. Through evaluating the optimal
combination of combustion conditions for a premixed slot-jet
array, this paper develops a practical approach for the sustainable
design of gas cooktop burners. Efficiency, CO and NOx emissions
in respect of an array of slot jets using premixed flames were
analysed. Response surface experimental design were applied to
three controllable factors of the combustion process, viz.
Reynolds number, equivalence ratio and jet-to-vessel distance.
Desirability Function Approach(DFA) is the analytic technique
used for the simultaneous optimization of the efficiency and
emission responses.
Abstract: In this work Artificial Intelligence (AI) techniques like Fuzzy logic, Genetic Algorithms and Particle Swarm Optimization have been used to improve the performance of the Automatic Generation Control (AGC) system. Instead of applying Genetic Algorithms and Particle swarm optimization independently for optimizing the parameters of the conventional AGC with PI controller, an intelligent tuned Fuzzy logic controller (acting as the secondary controller in the AGC system) has been designed. The controller gives an improved dynamic performance for both hydrothermal and thermal-thermal power systems under a variety of operating conditions.
Abstract: In this paper a new maximum power point tracking
algorithm for photovoltaic arrays is proposed. The algorithm detects
the maximum power point of the PV. The computed maximum
power is used as a reference value (set point) of the control system.
ON/OFF power controller with hysteresis band is used to control the
operation of a Buck chopper such that the PV module always
operates at its maximum power computed from the MPPT algorithm.
The major difference between the proposed algorithm and other
techniques is that the proposed algorithm is used to control directly
the power drawn from the PV.
The proposed MPPT has several advantages: simplicity, high
convergence speed, and independent on PV array characteristics. The
algorithm is tested under various operating conditions. The obtained
results have proven that the MPP is tracked even under sudden
change of irradiation level.
Abstract: Noise has adverse effect on human health and
comfort. Noise not only cause hearing impairment, but it also acts as
a causal factor for stress and raising systolic pressure. Additionally it
can be a causal factor in work accidents, both by marking hazards
and warning signals and by impeding concentration. Industry
workers also suffer psychological and physical stress as well as
hearing loss due to industrial noise. This paper proposes an approach
to enable engineers to point out quantitatively the noisiest source for
modification, while multiple machines are operating simultaneously.
The model with the point source and spherical radiation in a free field
was adopted to formulate the problem. The procedure works very
well in ideal cases (point source and free field). However, most of the
industrial noise problems are complicated by the fact that the noise is
confined in a room. Reflections from the walls, floor, ceiling, and
equipment in a room create a reverberant sound field that alters the
sound wave characteristics from those for the free field. So the model
was validated for relatively low absorption room at NIT Kurukshetra
Central Workshop. The results of validation pointed out that the
estimated sound power of noise sources under simultaneous
conditions were on lower side, within the error limits 3.56 - 6.35 %.
Thus suggesting the use of this methodology for practical
implementation in industry. To demonstrate the application of the
above analytical procedure for estimating the sound power of noise
sources under simultaneous operating conditions, a manufacturing
facility (Railway Workshop at Yamunanagar, India) having five
sound sources (machines) on its workshop floor is considered in this
study. The findings of the case study had identified the two most
effective candidates (noise sources) for noise control in the Railway
Workshop Yamunanagar, India. The study suggests that the
modification in the design and/or replacement of these two identified
noisiest sources (machine) would be necessary so as to achieve an
effective reduction in noise levels. Further, the estimated data allows
engineers to better understand the noise situations of the workplace
and to revise the map when changes occur in noise level due to a
workplace re-layout.
Abstract: A kinetic model for propane dehydrogenation in an
industrial moving bed reactor is developed based on the reported
reaction scheme. The kinetic parameters and activity constant are
fine tuned with several sets of balanced plant data. Plant data at
different operating conditions is applied to validate the model and
the results show a good agreement between the model
predictions and plant observations in terms of the amount of main
product, propylene produced. The simulation analysis of key
variables such as inlet temperature of each reactor (Tinrx) and
hydrogen to total hydrocarbon ratio (H2/THC) affecting process
performance is performed to identify the operating condition to
maximize the production of propylene. Within the range of operating
conditions applied in the present studies, the operating condition to
maximize the propylene production at the same weighted average
inlet temperature (WAIT) is ΔTinrx1= -2, ΔTinrx2= +1, ΔTinrx3= +1 ,
ΔTinrx4= +2 and ΔH2/THC= -0.02. Under this condition, the surplus
propylene produced is 7.07 tons/day as compared with base case.
Abstract: This paper describes a novel monitoring scheme to
minimize total active power in digital circuits depend on the demand
frequency, by adjusting automatically both supply voltage and
threshold voltages based on circuit operating conditions such as
temperature, process variations, and desirable frequency. The delay
monitoring results, will be control and apply so as to be maintained at
the minimum value at which the chip is able to operate for a given
clock frequency. Design details of power monitor are examined using
simulation framework in 32nm BTPM model CMOS process.
Experimental results show the overhead of proposed circuit in terms
of its power consumption is about 40 μW for 32nm technology;
moreover the results show that our proposed circuit design is not far
sensitive to the temperature variations and also process variations.
Besides, uses the simple blocks which offer good sensitivity, high
speed, the continuously feedback loop. This design provides up to
40% reduction in power consumption in active mode.
Abstract: With the growth of modern civilization and
industrialization in worldwide, the demand for energy is increasing
day by day. Majority of the world-s energy needs are met through
fossil fuels and natural gas. As a result the amount of fossil fuels is
on diminishing from year to year. Since the fossil fuel is nonrenewable,
so fuel price is gouging as a consequence of spiraling
demand and diminishing supply. At present the power generation of
our country is mainly depends on imported fossil fuels. To reduce the
dependency on imported fuel, the use of renewable sources has
become more popular. In Bangladesh coconut is widely growing tree.
Especially in the southern part of the country a large area will be
found where coconut tree is considered as natural asset. So, our
endeavor was to use the coconut oil as a renewable and alternative
fuel. This article shows the prospect of coconut oil as a renewable
and alternative fuel of diesel fuel. Since diesel engine has a versatile
uses including small electricity generation, an experimental set up is
then made to study the performance of a small diesel engine using
different blends of bio diesel converted from coconut oil. It is found
that bio diesel has slightly different properties than diesel. With
biodiesel the engine is capable of running without difficulty.
Different blends of bio diesel (i.e. B80, B60, and B 50 etc.) have
been used to avoid complicated modification of the engine or the fuel
supply system. Finally, a comparison of engine performance for
different blends of biodiesel has been carried out to determine the
optimum blend for different operating conditions.
Abstract: This paper investigates the development of weld zone
in Resistance Spot Welding (RSW) which focuses on weld nugget and Heat Affected Zone (HAZ). The effects of four factors namely
weld current, weld time, electrode force and hold time were studied using a general 24 factorial design augmented by five centre points. The results of the analysis showed that all selected factors except
hold time exhibit significant effect on weld nugget radius and HAZ size. Optimization of the welding parameters (weld current, weld
time and electrode force) to normalize weld nugget and to minimize
HAZ size was then conducted using Central Composite Design (CCD) in Response Surface Methodology (RSM) and the optimum
parameters were determined. A regression model for radius of weld nugget and HAZ size was developed and its adequacy was evaluated.
The experimental results obtained under optimum operating conditions were then compared with the predicted values and were
found to agree satisfactorily with each other
Abstract: The bromination of five selected pharmaceuticals
(metoprolol, naproxen, amoxicillin, hydrochlorotiazide and
phenacetin) in ultrapure water and in three water matrices (a
groundwater, a surface water from a public reservoir and a secondary
effluent from a WWTP) was investigated. The apparent rate
constants for the bromination reaction were determined as a function
of the pH, and the sequence obtained for the reaction rate was
amoxicillin > naproxen >> hydrochlorotiazide ≈ phenacetin ≈
metoprolol. The proposal of a kinetic mechanism, which specifies the
dissociation of bromine and each pharmaceutical according to their
pKa values and the pH allowed the determination of the intrinsic rate
constants for every elementary reaction. The influence of the main
operating conditions (pH, initial bromine dose, and the water matrix)
on the degradation of pharmaceuticals was established. In addition,
the presence of bromide in chlorination experiments was
investigated. The presence of bromide in wastewaters and drinking
waters in the range of 10 to several hundred μg L-1 accelerated
slightly the oxidation of the selected pharmaceuticals during chorine
disinfection.
Abstract: Biological treatment of secondary effluent wastewater
by two combined denitrification/oxic filtration systems packed with
Lock type(denitrification filter) and ceramic ball (oxic filter) has been
studied for 5months. Two phases of operating conditions were carried
out with an influent nitrate and ammonia concentrations varied from
5.8 to 11.7mg/L and 5.4 to 12.4mg/L,respectively.
Denitrification/oxic filter treatment system were operated under an
EBCT (Empty Bed Contact Time) of 4h at system recirculation ratio in
the range from 0 to 300% (Linear Velocity increased 19.5m/d to
78m/d). The system efficiency of denitrification , nitrification over
95% respectively. Total nitrogen and COD removal range from
54.6%(recirculation 0%) to 92.3%(recirculation 300%) and 10% to
62.5%, respectively.
Abstract: Potassium monopersulfate has been decomposed in aqueous solution in the presence of Co(II). The process has been simulated by means of a mechanism based on elementary reactions. Rate constants have been taken from literature reports or, alternatively, assimilated to analogous reactions occurring in Fenton's chemistry. Several operating conditions have been successfully applied.
Abstract: This paper presents a novel methodology for Maximum Power Point Tracking (MPPT) of a grid-connected 20 kW Photovoltaic (PV) system using neuro-fuzzy network. The proposed method predicts the reference PV voltage guarantying optimal power transfer between the PV generator and the main utility grid. The neuro-fuzzy network is composed of a fuzzy rule-based classifier and three Radial Basis Function Neural Networks (RBFNN). Inputs of the network (irradiance and temperature) are classified before they are fed into the appropriated RBFNN for either training or estimation process while the output is the reference voltage. The main advantage of the proposed methodology, comparing to a conventional single neural network-based approach, is the distinct generalization ability regarding to the nonlinear and dynamic behavior of a PV generator. In fact, the neuro-fuzzy network is a neural network based multi-model machine learning that defines a set of local models emulating the complex and non-linear behavior of a PV generator under a wide range of operating conditions. Simulation results under several rapid irradiance variations proved that the proposed MPPT method fulfilled the highest efficiency comparing to a conventional single neural network.
Abstract: The aim of this work is to investigate on the internalflow
patterns in a plate heat exchanger channel, which affect the
rate of sedimentation fouling on the heat transfer surface of the
plate heat exchanger. The research methodologies were the
computer simulation using Computational Fluid Dynamics (CFD)
and the experimental works. COMSOL MULTIPHYSICS™
Version 3.3 was used to simulate the velocity flow fields to verify
the low and high flow regions. The results from the CFD technique
were then compared with the images obtained from the
experiments in which the fouling test rig was set up with a singlechannel
plate heat exchanger to monitor the fouling of calcium
carbonate. Two parameters were varied i.e., the crossing angle of
the two plate: 55/55, 10/10, and 55/10 degree, and the fluid flow
rate at the inlet: 0.0566, 0.1132 and 0.1698 m/s. The type of plate
“GX-12" (the surface area 0.12 m2, the depth 2.9 mm, the width of
fluid flow 215 mm and the thickness of stainless plate of 0.5 mm)
was used in this study. The results indicated that the velocity
distribution for the case of 55/55 degree seems to be very well
organized when compared with the others. Also, an increase in the
inlet velocity resulted in the reduction of fouling rate on the surface
of plate heat exchangers.
Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: Radial flow reactor was focused for large scale
methanol synthesis and in which the heat transfer type was cross-flow.
The effects of operating conditions including the reactor inlet air
temperature, the heating pipe temperature and the air flow rate on the
cross-flow heat transfer was investigated and the results showed that
the temperature profile of the area in front of the heating pipe was
slightly affected by all the operating conditions. The main area whose
temperature profile was influenced was the area behind the heating
pipe. The heat transfer direction according to the air flow directions. In
order to provide the basis for radial flow reactor design calculation, the
dimensionless number group method was used for data fitting of the
bed effective thermal conductivity and the wall heat transfer
coefficient which was calculated by the mathematical model with the
product of Reynolds number and Prandtl number. The comparison of
experimental data and calculated value showed that the calculated
value fit the experimental data very well and the formulas could be
used for reactor designing calculation.
Abstract: The use of renewable energy sources becomes more
necessary and interesting. As wider applications of renewable energy
devices at domestic, commercial and industrial levels has not only
resulted in greater awareness, but also significantly installed
capacities. In addition, biomass principally is in the form of woods,
which is a form of energy by humans for a long time. Gasification is
a process of conversion of solid carbonaceous fuel into combustible
gas by partial combustion. Many gasifier models have various
operating conditions; the parameters kept in each model are different.
This study applied experimental data, which has three inputs, which
are; biomass consumption, temperature at combustion zone and ash
discharge rate. One output is gas flow rate. For this paper, neural
network was used to identify the gasifier system suitable for the
experimental data. In the result,neural networkis usable to attain the
answer.
Abstract: This paper presents a new approach for busbar protection with stable operation of current transformer during saturation, using fuzzy neuro and symmetrical components theory. This technique uses symmetrical components of current signals to learn the hidden relationship existing in the input patterns. Simulation studies are preformed and the influence of changing system parameters such as inception fault and source impedance is studied. Details of the design procedure and the results of performance studies with the proposed relay are given in the paper. An analysis of the performance of the proposed technique during ct saturation conditions is presented. The performance of the technique was investigated for a variety of operating conditions and for several busbar configurations. Data generated by EMTDC simulations of model power systems were used in the investigations. The results indicate that the proposed technique is stable during ct saturation conditions.