Abstract: In this paper we introduce a novel method for
the characterization of synchronziation and coupling effects
in multivariate time series that can be used for the analysis
of EEG or ECoG signals recorded during epileptic seizures.
The method allows to visualize the spatio-temporal evolution
of synchronization and coupling effects that are characteristic
for epileptic seizures. Similar to other methods proposed for
this purpose our method is based on a regression analysis.
However, a more general definition of the regression together
with an effective channel selection procedure allows to use the
method even for time series that are highly correlated, which
is commonly the case in EEG/ECoG recordings with large
numbers of electrodes. The method was experimentally tested
on ECoG recordings of epileptic seizures from patients with
temporal lobe epilepsies. A comparision with the results from
a independent visual inspection by clinical experts showed
an excellent agreement with the patterns obtained with the
proposed method.
Abstract: In this paper we present a new multichannel high
voltage driver box to connect up to six MOEMS mirror devices to it that have resonant and also quasistatically driven actuating electrodes. It is possible to drive all resonant axes synchronously
while the amplitude of them can individually be controlled by separate microcontrollers that also operate the quasistatic axes.
Circuit simulations are compared with the measurements done on the
real system and also show the robust driving performance of a
MOEMS mirror.
Abstract: An approach and its implementation in 0.18 m CMOS process of the multichannel ASIC for capacitive (up to 30 pF) sensors are described in the paper. The main design aim was to study an analog data-driven architecture. The design was done for an analog derandomizing function of the 128 to 16 structure. That means that the ASIC structure should provide a parallel front-end readout of 128 input analog sensor signals and after the corresponding fast commutation with appropriate arbitration logic their processing by means of 16 output chains, including analog-to-digital conversion. The principal feature of the ASIC is a low power consumption within 2 mW/channel (including a 9-bit 20Ms/s ADC) at a maximum average channel hit rate not less than 150 kHz.
Abstract: For gamma radiation detection, assemblies having
scintillation crystals and a photomultiplier tube, also there is a
preamplifier connected to the detector because the signals from
photomultiplier tube are of small amplitude. After pre-amplification
the signals are sent to the amplifier and then to the multichannel
analyser. The multichannel analyser sorts all incoming electrical
signals according to their amplitudes and sorts the detected photons
in channels covering small energy intervals. The energy range of
each channel depends on the gain settings of the multichannel
analyser and the high voltage across the photomultiplier tube. The
exit spectrum data of the two main isotopes studied ,putting data in
biomass program ,process it by Matlab program to get the solid
holdup image (solid spherical nuclear fuel)
Abstract: This paper describes the implementation and testing
of a multichannel active noise control system (ANCS) based on the
filtered-inverse LMS (FILMS) algorithm. The FILMS algorithm is
derived from the well-known filtered-x LMS (FXLMS) algorithm
with the aim to improve the rate of convergence of the multichannel
FXLMS algorithm and to reduce its computational load. Laboratory
setup and techniques used to implement this system efficiently are
described in this paper. Experiments performed in order to test the
performance of the FILMS algorithm are discussed and the obtained
results presented.
Abstract: Capacitive electrocardiogram (ECG) measurement is an attractive approach for long-term health monitoring. However, there is little literature available on its implementation, especially for multichannel system in standard ECG leads. This paper begins from the design criteria for capacitive ECG measurement and presents a multichannel limb-lead capacitive ECG system with conductive fabric tapes pasted on a double layer PCB as the capacitive sensors. The proposed prototype system incorporates a capacitive driven-body (CDB) circuit to reduce the common-mode power-line interference (PLI). The presented prototype system has been verified to be stable by theoretic analysis and practical long-term experiments. The signal quality is competitive to that acquired by commercial ECG machines. The feasible size and distance of capacitive sensor have also been evaluated by a series of tests. From the test results, it is suggested to be greater than 60 cm2 in sensor size and be smaller than 1.5 mm in distance for capacitive ECG measurement.