Abstract: This paper presents a new method of fault detection and isolation (FDI) for polymer electrolyte membrane (PEM) fuel cell (FC) dynamic systems under an open-loop scheme. This method uses a radial basis function (RBF) neural network to perform fault identification, classification and isolation. The novelty is that the RBF model of independent mode is used to predict the future outputs of the FC stack. One actuator fault, one component fault and three sensor faults have been introduced to the PEMFC systems experience faults between -7% to +10% of fault size in real-time operation. To validate the results, a benchmark model developed by Michigan University is used in the simulation to investigate the effect of these five faults. The developed independent RBF model is tested on MATLAB R2009a/Simulink environment. The simulation results confirm the effectiveness of the proposed method for FDI under an open-loop condition. By using this method, the RBF networks able to detect and isolate all five faults accordingly and accurately.
Abstract: Computational fluid dynamics (CFD) simulations
carried out in this paper show that spacer orientation has a major
influence on temperature patterns and on the heat transfer rates. The
local heat flux values significantly vary from high to very low values
at each filament when spacer touches the membrane surface. The
heat flux profile is more uniform when spacer filaments are not in
contact with the membrane thus making this arrangement more
beneficial. The temperature polarization is also found to be less in
this case when compared to the empty channel.
Abstract: In this study is presented a general methodology to
predict the performance of a continuous near-critical fluid extraction
process to remove compounds from aqueous solutions using hollow
fiber membrane contactors. A comprehensive 2D mathematical
model was developed to study Porocritical extraction process. The
system studied in this work is a membrane based extractor of ethanol
and acetone from aqueous solutions using near-critical CO2.
Predictions of extraction percentages obtained by simulations have
been compared to the experimental values reported by Bothun et al.
[5]. Simulations of extraction percentage of ethanol and acetone
show an average difference of 9.3% and 6.5% with the experimental
data, respectively. More accurate predictions of the extraction of
acetone could be explained by a better estimation of the transport
properties in the aqueous phase that controls the extraction of this
solute.
Abstract: The dynamics of Min proteins plays a center role in
accurate cell division. Although the nucleoids may presumably play
an important role in prokaryotic cell division, there is a lack of
models to account for its participation. In this work, we apply the
lattice Boltzmann method to investigate protein oscillation based on a
mesoscopic model that takes into account the nucleoid-s role. We
found that our numerical results are in reasonably good agreement
with the previous experimental results On comparing with the other
computational models without the presence of nucleoids, the
highlight of our finding is that the local densities of MinD and MinE
on the cytoplasmic membrane increases, especially along the cell
width, when the size of the obstacle increases, leading to a more
distinct cap-like structure at the poles. This feature indicated the
realistic pattern and reflected the combination of Min protein
dynamics and nucleoid-s role.
Abstract: In this paper, removal of chromium(VI) from aqueous
solution has been researched using reverse osmosis. The influence of
transmembrane pressure and feed concentration on permeate flux,
water recovery, permeate concentration, and salt rejection was
studied. The results showed that according to the variation of
transmembrane pressure and feed concentration, the permeate flux
and salt rejection were in the range 19.17 to 58.75 l/m2.min and
99.51 to 99.8 %, respectively. The highest permeate flux, 58.75
l/m2.min, and water recovery, 42.47 %, were obtained in the highest
pressure and the lowest feed concentration. On the other hand, the
lowest permeate concentration, 0.01 mg/l, and the highest salt
rejection, 99.8 %, were obtained in the highest pressure and the
lowest feed concentration.
Abstract: The beneficial effects of Si are mainly associated with
its high deposition in plant tissue and enhancing their strength and
rigidity. We investigated the role of Si against cadmium stress in
(Echium C) in house green condition. When the seventh leaves was
be appeared, plants were pretreated with five levels of Si: 0, 0.2, 0.5,
0.7and 1.5 mM Si (as sodium trisilicate, Na2(SiO2)3) and after that
plants were treated with two levels of Cd (30 and 90 mM). The
effects of Silicon and Cd were investigated on some physiological
and biochemical parameters such as: lipid peroxidation
(malondialdehyde (MDA) and other aldehydes, antocyanin and
flavonoid content. Our results showed that Cd significantly increased
MDA, other aldehydes, antocyanin and flavonoids content in
Echium and silicon offset the negative effect and increased tolerance
of Echium against Cd stress. From this results we concluded that Si
increase membrane integrity and antioxidative ability in this plant
against cd stress.
Abstract: Traditionally, Yemini Sidr honey has been reported to
cure liver problems, stomach ulcers, and respiratory disorders. In this
experiment, we evaluated Yemeni Sidr honey for its ability to protect
inflammations caused by acetic acid and formalin -induced writhing,
carrageenan and histamine-induced paw oedema in experimental rat
model. Hyperpyrexia, membrane stabilizing activity, and
phytochemical screening of the honey was also examined. Yemini
Sidr Honey at (100, 200 and 500 mg/kg) exhibited a concentration
dependant inhibition of acetic acid induced and formalin induced
writhing, paw oedema induced by carrageenan & histamine, and
hyperpyrexia induced by brewer's yeast, it also inhibited membrane
stabilizing activity. Phytochemical screenings of the honey reveal the
presence of flavonoids, steroid, alkaloids, saponins and tannins. This
study suggested that Yemeni Sidr honey possess very strong antiinflammatory,
analgesic and antipyretic effects and these effects
would be a result of the phytochemicals present.
Abstract: Analyse of locally manufactured Low Density Polyethylene (LDPE) durability, used within lining systems at bottom of Municipal Solid Waste (landfill), is done in the present work. For this end, short and middle time creep behavior under tension of the analyzed material is carried out. The locally manufactured material is tested and compared to the European one (LDPE-CE). Both materials was tested in 03 various mediums: ambient and two aggressive (salty water and foam water), using three specimens in each case. A testing campaign is carried out using an especially designed and achieved testing bench. Moreover, characterisation tests were carried out to evaluate the medium effect on the mechanical properties of the tested material (LDPE). Furthermore, experimental results have been used to establish a law regression which can be used to predict creep behaviour of the analyzed material. As a result, the analyzed LDPE material has showed a good stability in different ambient and aggressive mediums; as well, locally manufactured LDPE seems more flexible, compared with the European one. This makes it more useful to the desired application.
Abstract: A novel sponge submerged membrane bioreactor
(SSMBR) was developed to effectively remove organics and
nutrients from wastewater. Sponge is introduced within the SSMBR
as a medium for the attached growth of biomass. This paper evaluates
the effects of new and acclimatized sponges for dissolved organic
carbon (DOC) removal from wastewater at different mixed liquor
suspended solids- (MLSS) concentration of the sludge. It was
observed in a series of experimental studies that the acclimatized
sponge performed better than the new sponge whilst the optimum
DOC removal could be achieved at 10g/L of MLSS with the
acclimatized sponge. Moreover, the paper analyses the relationships
between the MLSSsponge/MLSSsludge and the DOC removal efficiency
of SSMBR. The results showed a non-linear relationship between the
biomass parameters of the sponge and the sludge, and the DOC
removal efficiency of SSMBR. A second-order polynomial function
could reasonably represent these relationships.
Abstract: The triumph of inductive neuro-stimulation since its rediscovery in the 1980s has been quite spectacular. In lots of branches ranging from clinical applications to basic research this system is absolutely indispensable. Nevertheless, the basic knowledge about the processes underlying the stimulation effect is still very rough and rarely refined in a quantitative way. This seems to be not only an inexcusable blank spot in biophysics and for stimulation prediction, but also a fundamental hindrance for technological progress. The already very sophisticated devices have reached a stage where further optimization requires better strategies than provided by simple linear membrane models of integrate-and-fire style. Addressing this problem for the first time, we suggest in the following text a way for virtual quantitative analysis of a stimulation system. Concomitantly, this ansatz seems to provide a route towards a better understanding by using nonlinear signal processing and taking the nerve as a filter that is adapted for neuronal magnetic stimulation. The model is compact and easy to adjust. The whole setup behaved very robustly during all performed tests. Exemplarily a recent innovative stimulator design known as cTMS is analyzed and dimensioned with this approach in the following. The results show hitherto unforeseen potentials.
Abstract: The objective of this study is to evaluate the
occurrence of fungi in aerobic and anoxic activated sludge from
membrane bioreactors (MBRs). Thirty-six samples of both aerobic
and anoxic activated sludge were taken from 2 MBR treating
domestic wastewater. Over a period of eight months 2 samples from
each plant were taken per month. The samples were prepared for
count and definition of fungi. The obtained data show that, sixty
species belonging to 27 genera were collected from activated sludge
samples under aerobic and anoxic conditions. Regarding to the fungi
definition, under aerobic condition the Geotrichum was found at
(8.8%) followed by Penicillium (75.0%), Yeasts (65.7%) and
Trichoderma (55.5%), while Yeasts (77.1%) Geotrichum
candidumand Penicillium (61.1%) species were the most prevalent in
anoxic activated sludge. The results indicate that activated sludge is
habitat for growth and sporulation of different groups of fungi, both
saprophytic and pathogenic.
Abstract: The study describes chitosan membrane platform
modified with nanostructure pattern which using nanotechnology to
fabricate. The cell-substrate interaction between neuro-2a neuroblasts
cell lines and chitosan membrane (flat, nanostructure and
nanostructure pattern types) was investigated. The adhered
morphology of neuro-2a cells depends on the topography of chitosan
surface. We have found that neuro-2a showed different morphogenesis
when cells adhered on flat and nanostructure chitosan membrane. The
cell projected area of neuro-2a on flat chitosan membrane is larger
than on nanostructure chitosan membrane. In addition, neuro-2a cells
preferred to adhere on flat chitosan surface region than on
nanostructure chitosan membrane to immobilize and differentiation.
The experiment suggests surface topography can be used as a critical
mechanism to isolate group of neuro-2a to a particular rectangle area
on chitosan membrane. Our finding will provide a platform to take
patch clamp to record electrophysiological behavior about neurons in
vitro in the future.
Abstract: We have developed a database for membrane protein functions, which has more than 3000 experimental data on functionally important amino acid residues in membrane proteins along with sequence, structure and literature information. Further, we have proposed different methods for identifying membrane proteins based on their functions: (i) discrimination of membrane transport proteins from other globular and membrane proteins and classifying them into channels/pores, electrochemical and active transporters, and (ii) β-signal for the insertion of mitochondrial β-barrel outer membrane proteins and potential targets. Our method showed an accuracy of 82% in discriminating transport proteins and 68% to classify them into three different transporters. In addition, we have identified a motif for targeting β-signal and potential candidates for mitochondrial β-barrel membrane proteins. Our methods can be used as effective tools for genome-wide annotations.
Abstract: In this study we investigate silica nanoparticle (SiO2- NP) effects on the structure and phase properties of supported lipid monolayers and bilayers, coupling surface pressure measurements, fluorescence microscopy and atomic force microscopy. SiO2-NPs typically in size range of 10nm to 100 nm in diameter are tested. Our results suggest first that lipid molecules organization depends to their nature. Secondly, lipid molecules in the vinicity of big aggregates nanoparticles organize in liquid condensed phase whereas small aggregates are localized in both fluid liquid-expanded (LE) and liquid-condenced (LC). We demonstrated also by atomic force microscopy that by measuring friction forces it is possible to get information as if nanoparticle aggregates are recovered or not by lipid monolayers and bilayers.
Abstract: For stricter drinking water regulations in the future, reducing the humic acid and disinfection byproducts in raw water, namely, trihalomethanes (THMs) and haloacetic acids (HAAs) is worthy for research. To investigate the removal of waterborne organic material using a lab-scale of bio-activated carbon filter under different EBCT, the concentrations of humic acid prepared were 0.01, 0.03, 0.06, 0.12, 0.17, 0.23, and 0.29 mg/L. Then we conducted experiments using a pilot plant with in-field of the serially connected bio-activated carbon filters and hollow fiber membrane processes employed in traditional water purification plants. Results showed under low TOC conditions of humic acid in influent (0.69 to 1.03 mg TOC/L) with an EBCT of 30 min, 40 min, and 50 min, TOC removal rates increases with greater EBCT, attaining about 39 % removal rate. The removal rate of THMs and HAAs by BACF was 54.8 % and 89.0 %, respectively.
Abstract: The direct discharge of palm oil mill effluent (POME) wastewater causes serious environmental pollution due to its high chemical oxygen demand (COD) and biochemical oxygen demand (BOD). Traditional ways for POME treatment have both economical and environmental disadvantages. In this study, a membrane anaerobic system (MAS) was used as an alternative, cost effective method for treating POME. Six steady states were attained as a part of a kinetic study that considered concentration ranges of 8,220 to 15,400 mg/l for mixed liquor suspended solids (MLSS) and 6,329 to 13,244 mg/l for mixed liquor volatile suspended solids (MLVSS). Kinetic equations from Monod, Contois and Chen & Hashimoto were employed to describe the kinetics of POME treatment at organic loading rates ranging from 2 to 13 kg COD/m3/d. throughout the experiment, the removal efficiency of COD was from 94.8 to 96.5% with hydraulic retention time, HRT from 400.6 to 5.7 days. The growth yield coefficient, Y was found to be 0.62gVSS/g COD the specific microorganism decay rate was 0.21 d-1 and the methane gas yield production rate was between 0.25 l/g COD/d and 0.58 l/g COD/d. Steady state influent COD concentrations increased from 18,302 mg/l in the first steady state to 43,500 mg/l in the sixth steady state. The minimum solids retention time, which was obtained from the three kinetic models ranged from 5 to 12.3 days. The k values were in the range of 0.35 – 0.519 g COD/ g VSS • d and values were between 0.26 and 0.379 d-1. The solids retention time (SRT) decreased from 800 days to 11.6 days. The complete treatment reduced the COD content to 2279 mg/l equivalent to a reduction of 94.8% reduction from the original.
Abstract: This work deals with modeling and simulation of SO2 removal in a ceramic membrane by means of FEM. A mass transfer model was developed to predict the performance of SO2 absorption in a chemical solvent. The model was based on solving conservation equations for gas component in the membrane. Computational fluid dynamics (CFD) of mass and momentum were used to solve the model equations. The simulations aimed to obtain the distribution of gas concentration in the absorption process. The effect of the operating parameters on the efficiency of the ceramic membrane was evaluated. The modeling findings showed that the gas phase velocity has significant effect on the removal of gas whereas the liquid phase does not affect the SO2 removal significantly. It is also indicated that the main mass transfer resistance is placed in the membrane and gas phase because of high tortuosity of the ceramic membrane.
Abstract: In this paper we have proposed a methodology to
develop an amperometric biosensor for the analysis of glucose
concentration using a simple microcontroller based data acquisition
system. The work involves the development of Detachable
Membrane Unit (enzyme based biomembrane) with immobilized
glucose oxidase on the membrane and interfacing the same to the
signal conditioning system. The current generated by the biosensor
for different glucose concentrations was signal conditioned, then
acquired and computed by a simple AT89C51-microcontroller. The
optimum operating parameters for the better performance were found
and reported. The detailed performance evaluation of the biosensor
has been carried out. The proposed microcontroller based biosensor
system has the sensitivity of 0.04V/g/dl, with a resolution of
50mg/dl. It has exhibited very good inter day stability observed up to
30 days. Comparing to the reference method such as HPLC, the
accuracy of the proposed biosensor system is well within ± 1.5%.
The system can be used for real time analysis of glucose
concentration in the field such as, food and fermentation and clinical
(In-Vitro) applications.
Abstract: Bacillus subtilis strain LB5 produced lipopeptide
antibiotic iturin A-2 in liquid medium. Crude extract
from cell-free supernatant of B. subtilis cultivated broth extracted
with n-butanol showed antifungal activity to conidial germination of
Colletotrichum gloeosporioides. The germination of conidia was
completely inhibited by crude extract. The ultrastructure of conidia
after treated with crude extract was found an accumulation of vesiclelike
material between cell wall and plasma membrane while this
accumulation was not observed in untreated and germinated conidia.
Besides, the cell wall was not affected by crude extract.
Abstract: Extraction of lactic acid by emulsion liquid membrane technology (ELM) using n-trioctyl amine (TOA) in n-heptane as carrier within the organic membrane along with sodium carbonate as acceptor phase was optimized by using response surface methodology (RSM). A three level Box-Behnken design was employed for experimental design, analysis of the results and to depict the combined effect of five independent variables, vizlactic acid concentration in aqueous phase (cl), sodium carbonate concentration in stripping phase (cs), carrier concentration in membrane phase (ψ), treat ratio, and batch extraction time (τ)
with equal volume of organic and external aqueous phase on lactic acid extraction efficiency. The maximum lactic acid extraction efficiency (ηext) of 98.21%from aqueous phase in a batch reactor using ELM was found at the optimized values for test variables, cl, cs, ψ, and τ as 0.06 [M], 0.18 [M], 4.72 (%,v/v), 1.98 (v/v) and 13.36 min respectively.