Abstract: Significant legislative changes are set to revolutionise the commercial shipping industry. Upcoming emissions restrictions will force operators to look at technologies that can improve the efficiency of their vessels -reducing fuel consumption and emissions. A device which may help in this challenge is the Ship Wind-Assisted Propulsion system (SWAP), an actively controlled aerofoil mounted vertically on the deck of a ship. The device functions in a similar manner to a sail on a yacht, whereby the aerodynamic forces generated by the sail reach an equilibrium with the hydrodynamic forces on the hull and a forward velocity results. Numerical and experimental testing of the SWAP device is presented in this study. Circulation control takes the form of a co-flow jet aerofoil, utilising both blowing from the leading edge and suction from the trailing edge. A jet at the leading edge uses the Coanda effect to energise the boundary layer in order to delay flow separation and create high lift with low drag. The SWAP concept has been originated by the research and development team at SMAR Azure Ltd. The device will be retrofitted to existing ships so that a component of the aerodynamic forces acts forward and partially reduces the reliance on existing propulsion systems. Wind tunnel tests have been carried out at the de Havilland wind tunnel at the University of Glasgow on a 1:20 scale model of this system. The tests aim to understand the airflow characteristics around the aerofoil and investigate the approximate lift and drag coefficients that an early iteration of the SWAP device may produce. The data exhibits clear trends of increasing lift as injection momentum increases, with critical flow attachment points being identified at specific combinations of jet momentum coefficient, Cµ, and angle of attack, AOA. Various combinations of flow conditions were tested, with the jet momentum coefficient ranging from 0 to 0.7 and the AOA ranging from 0° to 35°. The Reynolds number across the tested conditions ranged from 80,000 to 240,000. Comparisons between 2D computational fluid dynamics (CFD) simulations and the experimental data are presented for multiple Reynolds-Averaged Navier-Stokes (RANS) turbulence models in the form of normalised surface pressure comparisons. These show good agreement for most of the tested cases. However, certain simulation conditions exhibited a well-documented shortcoming of RANS-based turbulence models for circulation control flows and over-predicted surface pressures and lift coefficient for fully attached flow cases. Work must be continued in finding an all-encompassing modelling approach which predicts surface pressures well for all combinations of jet injection momentum and AOA.
Abstract: Effect of plunging motion on the pitch oscillating NACA0012 airfoil is investigated using computational fluid dynamics (CFD). A simulation model based on overset grid technology and k - ω shear stress transport (SST) turbulence model is established, and the numerical simulation results are compared with available experimental data and other simulations. Two cases of phase angle φ = 0, μ which represents the phase difference between the pitching and plunging motions of an airfoil are performed. Airfoil vortex generation, moving, and shedding are discussed in detail. Good agreements have been achieved with the available literature. The upward plunging motion made the equivalent angle of attack less than the actual one during pitching analysis. It is observed that the formation of the stall vortex is suppressed, resulting in a decrease in the lift coefficient and a delay of the stall angle. However, the downward plunging motion made the equivalent angle of attack higher the actual one.
Abstract: Numerical investigations are performed to analyze the flow behavior over NACA0015 and to evaluate the efficiency of synthetic jet as active control device. The second objective of this work is to investigate the influence of momentum coefficient of synthetic jet on the flow behaviour. The unsteady Reynolds-averaged Navier-Stokes equations of the turbulent flow are solved using, k-ω SST provided by ANSYS CFX-CFD code. The model presented in this paper is a comprehensive representation of the information found in the literature. Comparison of obtained numerical flow parameters with the experimental ones shows that the adopted computational procedure reflects nearly the real flow nature. Also, numerical results state that use of synthetic jets devices has positive effects on the flow separation, and thus, aerodynamic performance improvement of NACA0015 airfoil. It can also be observed that the use of synthetic jet increases the lift coefficient about 13.3% and reduces the drag coefficient about 52.7%.
Abstract: Numerical simulations of vortex-induced vibration of a three-dimensional flexible tube under uniform turbulent flow are calculated when Reynolds number is 1.35×104. In order to achieve the vortex-induced vibration, the three-dimensional unsteady, viscous, incompressible Navier-Stokes equation and LES turbulence model are solved with the finite volume approach, the tube is discretized according to the finite element theory, and its dynamic equilibrium equations are solved by the Newmark method. The fluid-tube interaction is realized by utilizing the diffusion-based smooth dynamic mesh method. Considering the vortex-induced vibration system, the variety trends of lift coefficient, drag coefficient, displacement, vertex shedding frequency, phase difference angle of tube are analyzed under different frequency ratios. The nonlinear phenomena of locked-in, phase-switch are captured successfully. Meanwhile, the limit cycle and bifurcation of lift coefficient and displacement are analyzed by using trajectory, phase portrait, and Poincaré sections. The results reveal that: when drag coefficient reaches its minimum value, the transverse amplitude reaches its maximum, and the “lock-in” begins simultaneously. In the range of lock-in, amplitude decreases gradually with increasing of frequency ratio. When lift coefficient reaches its minimum value, the phase difference undergoes a suddenly change from the “out-of-phase” to the “in-phase” mode.
Abstract: A two-dimensional numerical study for flow past a square cylinder in presence of flat plate both at upstream and downstream position is carried out using the single-relaxation-time lattice Boltzmann method for gap spacing 0.5 and 1. We select Reynolds numbers from 80 to 200. The wake structure mechanism within gap spacing and near wake region, vortex structures around and behind the main square cylinder in presence of flat plate are studied and compared with flow pattern around a single square cylinder. The results are obtained in form of vorticity contour, streamlines, power spectra analysis, time trace analysis of drag and lift coefficients. Four different types of flow patterns were observed in both configurations, named as (i) Quasi steady flow (QSF), (ii) steady flow (SF), (iii) shear layer reattachment (SLR), (iv) single bluff body (SBB). It is observed that upstream flat plate plays a vital role in significant drag reduction. On the other hand, rate of suppression of vortex shedding is high for downstream flat plate case at low Reynolds numbers. The reduction in mean drag force and root mean square value of drag force for upstream flat plate case are89.1% and 86.3% at (Re, g) = (80, 0.5d) and (120, 1d) and reduction for downstream flat plate case for mean drag force and root mean square value of drag force are 11.10% and 97.6% obtained at (180, 1d) and (180, 0.5d).
Abstract: Unsteady flow and heat transfer from a circular
cylinder in cross-flow is studied numerically. The governing
equations are solved by using finite volume method. Reynolds
number varies in range of 50 to 200; in this range flow is considered
to be laminar and unsteady. Al2O3 nanoparticle with volume fraction
in range of 5% to 20% is added to pure water. Effects of adding
nanoparticle to pure water on lift and drag coefficient and Nusselt
number is presented. Addition of Al2O3 has inconsiderable effect on
the value of drags and lift coefficient. However, it has significant
effect on heat transfer; results show that heat transfer of Al2O3
nanofluid is about 9% to 36% higher than pure water.
Abstract: Due to the interference effects, the intrinsic
aerodynamic parameters obtained from the individual component
testing are always fundamentally different than those obtained for
complete model testing. Consideration and limitation for such testing
need to be taken into account in any design work related to the
component buildup method. In this paper, the scaled model of a
straight rectangular canard of a hybrid buoyant aircraft is tested at 50
m/s in IIUM-LSWT (Low Speed Wind Tunnel). Model and its
attachment with the balance are kept rigid to have results free from
the aeroelastic distortion. Based on the velocity profile of the test
section’s floor; the height of the model is kept equal to the
corresponding boundary layer displacement. Balance measurements
provide valuable but limited information of overall aerodynamic
behavior of the model. Zero lift coefficient is obtained at -2.2o and
the corresponding drag coefficient was found to be less than that at
zero angle of attack. As a part of the validation of low fidelity tool,
plot of lift coefficient plot was verified by the experimental data and
except the value of zero lift coefficients, the overall trend has under
predicted the lift coefficient. Based on this comparative study, a
correction factor of 1.36 is proposed for lift curve slope obtained
from the panel method.
Abstract: In this research numerical simulations are performed,
using the multi-relaxation-time lattice Boltzmann method, in the
range 3 ≤ β = w[d] ≤ 30 at Re = 100, 200 and 300, where β the
blockage ratio, w is the equispaced distance between centers of
cylinders, d is the diameter of the cylinder and Re is the Reynolds
number, respectively. Special attention is paid to the effect of the
equispaced distance between centers of cylinders. Visualization of
the vorticity contour visualization are presented for some simulation
showing the flow dynamics and patterns for blockage effect. Results
show that the drag and mean drag coefficients, and Strouhal number,
in general, decrease with the increase of β for fixed Re. It is found
that the decreasing rate of drag and mean drag coefficients and
Strouhal number is more distinct in the range 3 ≤ β ≤ 15. We found
that when β > 15, the blockage effect almost diminishes. Our results
further indicate that the drag and mean drag coefficients, peak value
of the lift coefficient, root-mean-square value of the lift and drag
coefficients and the ratio between lift and drag coefficients decrease
with the increase of Re. The results indicate that symmetry boundary
condition have more blockage effect as compared to periodic
boundary condition.
Abstract: A two-dimensional numerical simulation of crossflow
around four cylinders in an in-line rectangular configuration is
studied by using the lattice Boltzmann method (LBM). Special
attention is paid to the effect of the spacing between the cylinders.
The Reynolds number ( Re ) is chosen to be e 100 R = and the
spacing ratio L / D is set at 0.5, 1.5, 2.5, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0
and 10.0. Results show that, as in the case of four cylinders in an inline
rectangular configuration , flow fields show four different
features depending on the spacing (single square cylinder, stable
shielding flow, wiggling shielding flow and a vortex shedding flow)
are observed in this study. The effects of spacing ratio on physical
quantities such as mean drag coefficient, Strouhal number and rootmean-
square value of the drag and lift coefficients are also presented.
There is more than one shedding frequency at small spacing ratios.
The mean drag coefficients for downstream cylinders are less than
that of the single cylinder for all spacing ratios. The present results
using the LBM are compared with some existing experimental data
and numerical studies. The comparison shows that the LBM can
capture the characteristics of the bluff body flow reasonably well and
is a good tool for bluff body flow studies.
Abstract: The performance of Advection Upstream Splitting
Method AUSM schemes are evaluated against experimental flow
fields at different Mach numbers and results are compared with
experimental data of subsonic, supersonic and hypersonic flow fields.
The turbulent model used here is SST model by Menter. The
numerical predictions include lift coefficient, drag coefficient and
pitching moment coefficient at different mach numbers and angle of
attacks. This work describes a computational study undertaken to
compute the Aerodynamic characteristics of different air vehicles
configurations using a structured Navier-Stokes computational
technique. The CFD code bases on the idea of upwind scheme for the
convective (convective-moving) fluxes. CFD results for GLC305
airfoil and cone cylinder tail fined missile calculated on above
mentioned turbulence model are compared with the available data.
Wide ranges of Mach number from subsonic to hypersonic speeds are
simulated and results are compared. When the computation is done
by using viscous turbulence model the above mentioned coefficients
have a very good agreement with the experimental values. AUSM
scheme is very efficient in the regions of very high pressure gradients
like shock waves and discontinuities. The AUSM versions simulate
the all types of flows from lower subsonic to hypersonic flow without
oscillations.
Abstract: Gliding during night without electric power is an efficient method to enhance endurance performance of solar aircrafts. The properties of maximum gliding endurance path are studied in this paper. The problem is formulated as an optimization problem about maximum endurance can be sustained by certain potential energy storage with dynamic equations and aerodynamic parameter constrains. The optimal gliding path is generated based on gauss pseudo-spectral method. In order to analyse relationship between altitude, velocity of solar UAVs and its endurance performance, the lift coefficient in interval of [0.4, 1.2] and flight envelopes between 0~30km are investigated. Results show that broad range of lift coefficient can improve solar aircrafts- long endurance performance, and it is possible for a solar aircraft to achieve the aim of long endurance during whole night just by potential energy storage.
Abstract: Numerical calculations of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann method at Reynolds number 150. The effects of upstream locations, downstream locations and blockage are investigated systematically. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The results had shown that the upstream, downstream and height of the computational domain are at least 7.5, 37.5 and 12 diameters of the cylinder, respectively.
Abstract: Flow around a flat tube is studied numerically. Reynolds number is defined base on equivalent circular tube and it is varied in range of 100 to 300. Equations are solved by using finite volume method and results are presented in form of drag and lift coefficient. Results show that drag coefficient of flat tube is up to 66% lower than circular tube with equivalent diameter. In addition, by increasing l/D from 1 to 2, the drag coefficient of flat tube is decreased about 14-27%.
Abstract: A numerical simulation of vortex-induced vibration of
a 2-dimensional elastic circular cylinder with two degree of freedom
under the uniform flow is calculated when Reynolds is 200.
2-dimensional incompressible Navier-Stokes equations are solved
with the space-time finite element method, the equation of the cylinder
motion is solved with the new explicit integral method and the mesh
renew is achieved by the spring moving mesh technology. Considering
vortex-induced vibration with the low reduced damping parameter, the
variety trends of the lift coefficient, the drag coefficient, the
displacement of cylinder are analyzed under different oscillating
frequencies of cylinder. The phenomena of locked-in, beat and
phases-witch were captured successfully. The evolution of vortex
shedding from the cylinder with time is discussed. There are very
similar trends in characteristics between the results of the one degree
of freedom cylinder model and that of the two degree of freedom
cylinder model. The streamwise vibrations have a certain effect on the
lateral vibrations and their characteristics.
Abstract: Numerical investigation of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann methods at different Reynolds numbers. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations, streamlines and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The Reynolds numbers affected the physical quantities.
Abstract: The measurement of aerodynamic forces and moments
acting on an aircraft model is important for the development of wind
tunnel measurement technology to predict the performance of the full
scale vehicle. The potentials of an aircraft model with and without
winglet and aerodynamic characteristics with NACA wing No. 65-3-
218 have been studied using subsonic wind tunnel of 1 m × 1 m
rectangular test section and 2.5 m long of Aerodynamics Laboratory
Faculty of Engineering (University Putra Malaysia). Focusing on
analyzing the aerodynamic characteristics of the aircraft model, two
main issues are studied in this paper. First, a six component wind
tunnel external balance is used for measuring lift, drag and pitching
moment. Secondly, Tests are conducted on the aircraft model with
and without winglet of two configurations at Reynolds numbers
1.7×105, 2.1×105, and 2.5×105 for different angle of attacks. Fuzzy
logic approach is found as efficient for the representation,
manipulation and utilization of aerodynamic characteristics.
Therefore, the primary purpose of this work was to investigate the
relationship between lift and drag coefficients, with free-stream
velocities and angle of attacks, and to illustrate how fuzzy logic
might play an important role in study of lift aerodynamic
characteristics of an aircraft model with the addition of certain
winglet configurations. Results of the developed fuzzy logic were
compared with the experimental results. For lift coefficient analysis,
the mean of actual and predicted values were 0.62 and 0.60
respectively. The coreelation between actual and predicted values
(from FLS model) of lift coefficient in different angle of attack was
found as 0.99. The mean relative error of actual and predicted valus
was found as 5.18% for the velocity of 26.36 m/s which was found to
be less than the acceptable limits (10%). The goodness of fit of
prediction value was 0.95 which was close to 1.0.
Abstract: This work describes the aerodynamic characteristic for
aircraft wing model with and without bird feather like winglet. The
aerofoil used to construct the whole structure is NACA 653-218
Rectangular wing and this aerofoil has been used to compare the
result with previous research using winglet. The model of the
rectangular wing with bird feather like winglet has been fabricated
using polystyrene before design using CATIA P3 V5R13 software
and finally fabricated in wood. The experimental analysis for the
aerodynamic characteristic for rectangular wing without winglet,
wing with horizontal winglet and wing with 60 degree inclination
winglet for Reynolds number 1.66×105, 2.08×105 and 2.50×105 have
been carried out in open loop low speed wind tunnel at the
Aerodynamics laboratory in Universiti Putra Malaysia. The
experimental result shows 25-30 % reduction in drag coefficient and
10-20 % increase in lift coefficient by using bird feather like winglet
for angle of attack of 8 degree.