Abstract: Numerical modeling of fluid flows, whether compressible or incompressible, laminar or turbulent presents a considerable contribution in the scientific and industrial fields. However, the development of an approximate model of a supersonic flow requires the introduction of specific and more precise techniques and methods. For this purpose, the object of this paper is modeling a supersonic flow of inviscid fluid around a dihedral airfoil. Based on the thin airfoils theory and the non-dimensional stationary Steichen equation of a two-dimensional supersonic flow in isentropic evolution, we obtained a solution for the downstream velocity potential of the oblique shock at the second order of relative thickness that characterizes a perturbation parameter. This result has been dealt with by the asymptotic analysis and characteristics method. In order to validate our model, the results are discussed in comparison with theoretical and experimental results. Indeed, firstly, the comparison of the results of our model has shown that they are quantitatively acceptable compared to the existing theoretical results. Finally, an experimental study was conducted using the AF300 supersonic wind tunnel. In this experiment, we have considered the incident upstream Mach number over a symmetrical dihedral airfoil wing. The comparison of the different Mach number downstream results of our model with those of the existing theoretical data (relative margin between 0.07% and 4%) and with experimental results (concordance for a deflection angle between 1° and 11°) support the validation of our model with accuracy.
Abstract: The choice of high-speed, low budget hatchback car with diversified options is increasing for meeting the new generation buyers trend. This paper is aimed to augment the current speed of the hatchback cars through the aerodynamic drag reduction technique. The inverted airfoils are facilitated at the bottom of the car for generating the downward force for negating the lift while increasing the current speed range for achieving a better road performance. The numerical simulations have been carried out using a 2D steady pressure-based k-ɛ realizable model with enhanced wall treatment. In our numerical studies, Reynolds-averaged Navier-Stokes model and its code of solution are used. The code is calibrated and validated using the exact solution of the 2D boundary layer displacement thickness at the Sanal flow choking condition for adiabatic flows. We observed through the parametric analytical studies that the inverted airfoil integrated with the bottom surface at various predesigned locations of Hatchback cars can improve its overall aerodynamic efficiency through drag reduction, which obviously decreases the fuel consumption significantly and ensure an optimum road performance lucratively with maximum permissible speed within the framework of the manufactures constraints.
Abstract: The aim of the research work is to modify the NACA 4215 airfoil with flap and rotary cylinder at the leading edge of the airfoil and experimentally study the static pressure distribution over the airfoil completed with flap and leading-edge vortex generator. In this research, NACA 4215 wing model has been constructed by generating the profile geometry using the standard equations and design software such as AutoCAD and SolidWorks. To perform the experiment, three wooden models are prepared and tested in subsonic wind tunnel. The experiments were carried out in various angles of attack. Flap angle and momentum injection rate are changed to observe the characteristics of pressure distribution. In this research, a new concept of flow separation control mechanism has been introduced to improve the aerodynamic characteristics of airfoil. Control of flow separation over airfoil which experiences a vortex generator (rotating cylinder) at the leading edge of airfoil is experimentally simulated under the effects of momentum injection. The experimental results show that the flow separation control is possible by the proposed mechanism, and benefits can be achieved by momentum injection technique. The wing performance is significantly improved due to control of flow separation by momentum injection method.
Abstract: In this paper, we show shallow water in a tin box as an analogous simulation tool for high-speed aerodynamics education and research. It is customary that we use a water tank to create shallow water flow. While a flow in a water tank is not necessarily uniform and is sometimes wavy, we can visualize a clear supercritical flow even when we move a body manually in stationary water in a simple shallow tin box. We can visualize a blunt shock wave around a moving circular cylinder together with a shock pattern around a diamond airfoil. Another interesting analogous experiment is a hydrodynamic shock tube with water and tea. We observe the contact surface clearly due to color difference of the two liquids those are invisible in the real gas dynamics experiment. We first revisit the similarities between high-speed aerodynamics and shallow water hydraulics. Several educational and research experiments are then introduced for engineering students. Shallow water experiments in a tin box simulate properly the high-speed flows.
Abstract: In the present study, the aerodynamic performance of a rigid two-dimensional pitching bio-inspired corrugate airfoil was numerically investigated at Reynolds number of 14000. The Open Field Operations And Manipulations (OpenFOAM) computational fluid dynamic tool is used to solve flow governing equations numerically. The k-ω SST turbulence model with low Reynolds correction (k-ω SST LRC) and the pimpleDyMFOAM solver are utilized to simulate the flow field around pitching bio-airfoil. The lift and drag coefficients of the airfoil are calculated at reduced frequencies k=1.24-4.96 and the angular amplitude of A=5°-20°. Results show that in a fixed reduced frequency, the absolute value of the sectional lift and drag coefficients increase with increasing pitching amplitude. In a fixed angular amplitude, the absolute value of the lift and drag coefficients increase as the pitching reduced frequency increases.
Abstract: Noise disturbance is one of the major factors considered in the fast development of aircraft technology. This paper reviews the flow field, which is examined on the 2D NACA0015 and 3D NACA0012 blade profile using SST k-ω turbulence model to compute the unsteady flow field. We inserted the time-dependent flow area variables in Ffowcs-Williams and Hawkings (FW-H) equations as an input and Sound Pressure Level (SPL) values will be computed for different angles of attack (AoA) from the microphone which is positioned in the computational domain to investigate effect of augmentation of unsteady 2D and 3D airfoil region noise level. The computed results will be compared with experimental data which are available in the open literature. As results; one of the calculated Cp is slightly lower than the experimental value. This difference could be due to the higher Reynolds number of the experimental data. The ANSYS Fluent software was used in this study. Fluent includes well-validated physical modeling capabilities to deliver fast, accurate results across the widest range of CFD and multiphysics applications. This paper includes a study which is on external flow over an airfoil. The case of 2D NACA0015 has approximately 7 million elements and solves compressible fluid flow with heat transfer using the SST turbulence model. The other case of 3D NACA0012 has approximately 3 million elements.
Abstract: The fuel consumption of modern, high wing loading, commercial aircraft in the first stage of flight is high because the usable flight level is lower and the weather conditions (jet stream) have great impact on aircraft performance. To reduce the fuel consumption, it is necessary to raise during first stage of flight the L/D ratio value within Cl 0.55-0.65. Different variable geometrical wing trailing edge modifications of SC(2)-410 airfoil were compared at M 0.78 using the CFD software STAR-CCM+ simulation based Reynolds-averaged Navier-Stokes (RANS) equations. The numerical results obtained show that by increasing the width of the airfoil by 4% and by modifying the trailing edge airfoil, it is possible to decrease airfoil drag at Cl 0.70 for up to 26.6% and at the same time to increase commercial aircraft L/D ratio for up to 5.0%. Fuel consumption can be reduced in proportion to the increase in L/D ratio.
Abstract: Effect of plunging motion on the pitch oscillating NACA0012 airfoil is investigated using computational fluid dynamics (CFD). A simulation model based on overset grid technology and k - ω shear stress transport (SST) turbulence model is established, and the numerical simulation results are compared with available experimental data and other simulations. Two cases of phase angle φ = 0, μ which represents the phase difference between the pitching and plunging motions of an airfoil are performed. Airfoil vortex generation, moving, and shedding are discussed in detail. Good agreements have been achieved with the available literature. The upward plunging motion made the equivalent angle of attack less than the actual one during pitching analysis. It is observed that the formation of the stall vortex is suppressed, resulting in a decrease in the lift coefficient and a delay of the stall angle. However, the downward plunging motion made the equivalent angle of attack higher the actual one.
Abstract: Computations for two-dimensional flow past a stationary and harmonically pitching wind turbine airfoil at a moderate value of Reynolds number (400000) are carried out by progressively increasing the angle of attack for stationary airfoil and at fixed pitching frequencies for rotary one. The incompressible Navier-Stokes equations in conjunction with Unsteady Reynolds Average Navier-Stokes (URANS) equations for turbulence modeling are solved by OpenFOAM package to investigate the aerodynamic phenomena occurred at stationary and pitching conditions on a NACA 6-series wind turbine airfoil. The aim of this study is to enhance the accuracy of numerical simulation in predicting the aerodynamic behavior of an oscillating airfoil in OpenFOAM. Hence, for turbulence modelling, k-ω-SST with low-Reynolds correction is employed to capture the unsteady phenomena occurred in stationary and oscillating motion of the airfoil. Using aerodynamic and pressure coefficients along with flow patterns, the unsteady aerodynamics at pre-, near-, and post-static stall regions are analyzed in harmonically pitching airfoil, and the results are validated with the corresponding experimental data possessed by the authors. The results indicate that implementing the mentioned turbulence model leads to accurate prediction of the angle of static stall for stationary airfoil and flow separation, dynamic stall phenomenon, and reattachment of the flow on the surface of airfoil for pitching one. Due to the geometry of the studied 6-series airfoil, the vortex on the upper surface of the airfoil during upstrokes is formed at the trailing edge. Therefore, the pattern flow obtained by our numerical simulations represents the formation and change of the trailing-edge vortex at near- and post-stall regions where this process determines the dynamic stall phenomenon.
Abstract: Numerical investigations are performed to analyze the flow behavior over NACA0015 and to evaluate the efficiency of synthetic jet as active control device. The second objective of this work is to investigate the influence of momentum coefficient of synthetic jet on the flow behaviour. The unsteady Reynolds-averaged Navier-Stokes equations of the turbulent flow are solved using, k-ω SST provided by ANSYS CFX-CFD code. The model presented in this paper is a comprehensive representation of the information found in the literature. Comparison of obtained numerical flow parameters with the experimental ones shows that the adopted computational procedure reflects nearly the real flow nature. Also, numerical results state that use of synthetic jets devices has positive effects on the flow separation, and thus, aerodynamic performance improvement of NACA0015 airfoil. It can also be observed that the use of synthetic jet increases the lift coefficient about 13.3% and reduces the drag coefficient about 52.7%.
Abstract: The boundary layer separation and new active flow control of a NACA 0025 airfoil were studied experimentally. This new flow control is sometimes known as a co-flow jet (cfj) airfoil. This paper presents the fluctuating velocity in a wall jet over the co-flow jet airfoil subjected to an adverse pressure gradient and a curved surface. In these results, the fluctuating velocity at the inner part increasing by increased the angle of attack up to 12o and this has due to the jet energized, while the angle of attack 20o has different. The airfoil cord based Reynolds number has 105.
Abstract: This paper presents the results of a Finite Element
based vibration analysis of a solar powered Unmanned Aerial
Vehicle (UAV). The purpose of this paper was to quantify the free
vibration, forced vibration response due to differing point inputs in
order to predict the relative response magnitudes and frequencies at
various wing locations of vibration induced power generators
(magnet in coil) excited by gust and/or control surface pulse-decays
used to help power the flight of the electric UAV. A Fluid Structure
Interaction (FSI) study was performed in order to ascertain pertinent
design stresses and deflections as well as aerodynamic parameters of
the UAV airfoil. The 10 ft span airfoil is modeled using Mylar as the
primary material. Results show that the free mode in bending is 4.8
Hz while the first forced bending mode is on range of 16.2 to 16.7 Hz
depending on the location of excitation. The free torsional bending
mode is 28.3 Hz, and the first forced torsional mode is range of 26.4
to 27.8 Hz, depending on the location of excitation. The FSI results
predict the coefficients of aerodynamic drag and lift of 0.0052 and
0.077, respectively, which matches hand-calculations used to validate
the Finite Element based results. FSI based maximum von Mises
stresses and deflections were found to be 0.282 MPa and 3.4 mm,
respectively. Dynamic pressures on the airfoil range from 1.04 to
1.23 kPa corresponding to velocity magnitudes in range of 22 to 66
m/s.
Abstract: The main objective of aircraft aerodynamics is to
enhance the aerodynamic characteristics and maneuverability of the
aircraft. This enhancement includes the reduction in drag and stall
phenomenon. The airfoil which contains dimples will have
comparatively less drag than the plain airfoil. Introducing dimples on
the aircraft wing will create turbulence by creating vortices which
delays the boundary layer separation resulting in decrease of pressure
drag and also increase in the angle of stall. In addition, wake
reduction leads to reduction in acoustic emission. The overall
objective of this paper is to improve the aircraft maneuverability by
delaying the flow separation point at stall and thereby reducing the
drag by applying the dimple effect over the aircraft wing. This project
includes both computational and experimental analysis of dimple
effect on aircraft wing, using NACA 0018 airfoil. Dimple shapes of
Semi-sphere, hexagon, cylinder, square are selected for the analysis;
airfoil is tested under the inlet velocity of 30m/s and 60m/s at
different angle of attack (5˚, 10˚, 15˚, 20˚, and 25˚). This analysis
favors the dimple effect by increasing L/D ratio and thereby
providing the maximum aerodynamic efficiency, which provides the
enhanced performance for the aircraft.
Abstract: An active slat is developed to increase the lift and delay
the separation for a DU96-W180 airfoil. The active slat is a fixed slat
that can be closed, fully opened or intermittently opened by a rotating
vane depending on the need. Experimental results show that the active
slat has reduced the mean pressure and increased the mean velocity
on the suction side of the airfoil for all positive angles of attack,
indicating an increase of lift. The experimental data and numerical
simulations also show that the direction of actuator vane rotation can
influence the mixing of the flow streams on the suction side and
hence influence the aerodynamic performance.
Abstract: The unsteady flow field around oscillating OA-209 airfoil at a Reynolds number of 3.5×105 were investigated. Three different reduced frequencies were tested in order to see how it affects the hysteresis loop of an airfoil. At a reduced frequency of 0.05 the deep dynamic stall phenomenon was observed. Lift overshooting was observed as a result of dynamic stall vortex (DSV) shedding. Further investigation was carried out to find out the cause of DSV formation and shedding over airfoil. Particle image velocimetry (PIV) and CFD tools were used and it was found out that dynamic stall separation (DSS), which is separated from leading edge separation (LES) and trailing edge separation (TES), triggered the dynamic stall vortex (DSV).
Abstract: The development of biomimetic micro-aerial-vehicles
(MAVs) with flapping wings is the future trend in military/domestic
field. The successful flight of MAVs is strongly related to the
understanding of unsteady aerodynamic performance of low Reynolds
number airfoils under dynamic flapping motion. This study explored
the effects of flapping frequency, stroke amplitude, and the inclined
angle of stroke plane on lift force and thrust force of a bio-inspiration
corrugated airfoil with 33 full factorial design of experiment and
ANOVA analysis. Unsteady vorticity flows over a corrugated thin
airfoil executing flapping motion are computed with time-dependent
two-dimensional laminar incompressible Reynolds-averaged
Navier-Stokes equations with the conformal hybrid mesh. The tested
freestream Reynolds number based on the chord length of airfoil as
characteristic length is fixed of 103. The dynamic mesh technique is
applied to model the flapping motion of a corrugated airfoil. Instant
vorticity contours over a complete flapping cycle clearly reveals the
flow mechanisms for lift force generation are dynamic stall, rotational
circulation, and wake capture. The thrust force is produced as the
leading edge vortex shedding from the trailing edge of airfoil to form a
reverse von Karman vortex. Results also indicated that the inclined
angle is the most significant factor on both the lift force and thrust
force. There are strong interactions between tested factors which mean
an optimization study on parameters should be conducted in further
runs.
Abstract: This paper presents a mean for reducing the torque
variation during the revolution of a vertical-axis wind turbine
(VAWT) by increasing the blade number. For this purpose, twodimensional
CDF analysis have been performed on a straight-bladed
Darreius-type rotor. After describing the computational model, a
complete campaign of simulations based on full RANS unsteady
calculations is proposed for a three, four and five-bladed rotor
architecture characterized by a NACA 0025 airfoil. For each
proposed rotor configuration, flow field characteristics are
investigated at several values of tip speed ratio, allowing a
quantification of the influence of blade number on flow geometric
features and dynamic quantities, such as rotor torque and power.
Finally, torque and power curves are compared for the analyzed
architectures, achieving a quantification of the effect of blade number
on overall rotor performance.
Abstract: The problem of incompressible steady flow simulation around an airfoil is discussed. For some simplest airfoils (circular, elliptical, Zhukovsky airfoils) the exact solution is known from complex analysis. It allows to compute the intensity of vortex layer which simulates the airfoil. Some modifications of the vortex element method are proposed and test computations are carried out. It-s shown that the these approaches are much more effective in comparison with the classical numerical scheme.
Abstract: A potential flow model is used to study the unsteady
flow past two airfoils in configuration, each of which is suddenly set
into motion. The airfoil bound vortices are modeled using lumped
vortex elements and the wake behind the airfoil is modeled by discrete
vortices. This consists of solving a steady state flow problem at each
time-step where unsteadiness is incorporated through the “zero normal
flow on a solid surface" boundary condition at every time instant.
Additionally, along with the “zero normal flow on a solid surface"
boundary condition Kelvin-s condition is used to compute the strength
of the latest wake vortex shed from the trailing edge of the airfoil.
Location of the wake vortices is updated at each time-step to get the
wake shape at each time instant. Results are presented to show the
effect of airfoil-airfoil interaction and airfoil-wake interaction on the
aerodynamic characteristics of each airfoil.
Abstract: This paper presents a numerical analysis of the
performance of a three-bladed Darrieus vertical-axis wind turbine
based on the DU91-W2-250 airfoil. A complete campaign of 2-D
simulations, performed for several values of tip speed ratio and based
on RANS unsteady calculations, has been performed to obtain the
rotor torque and power curves. Rotor performances have been
compared with the results of a previous work based on the use of the
NACA 0021 airfoil. Both the power coefficient and the torque
coefficient have been determined as a function of the tip speed ratio.
The flow field around rotor blades has also been analyzed. As a final
result, the performance of the DU airfoil based rotor appears to be
lower than the one based on the NACA 0021 blade section. This
behavior could be due to the higher stall characteristics of the NACA
profile, being the separation zone at the trailing edge more extended
for the DU airfoil.