Abstract: Implementing significant advantages in the supply of self-compacting concrete (SCC) is necessary because of the, negative features of SCC. Examples of these features are the ductility problem along with the very high cost of its constituted materials. Silica fume with steel fiber can fix this matter by improving the ductility and decreasing the total cost of SCC by varying the cement ingredients. Many different researchers have found that there have not been enough research carried out on the steel fiber-reinforced self-compacting concrete (SFRSCC) produced with silica fume. This paper inspects both the fresh and the mechanical properties of SFRSCC with silica fume, the fresh qualities where slump flow, slump T50 and V- funnel. While, the mechanical characteristics were the compressive strength, ultrasound pulse velocity (UPV) and elastic modulus of the concrete samples. The experimental results have proven that steel fiber can enhance the mechanical features. In addition, the silica fume within the entire hybrid mix may possibly adapt the fiber dispersion and strengthen deficits due to the fibers. It could also improve the strength plus the bond between the fiber and the matrix with a dense calcium silicate-hydrate gel in SFRSCC. The concluded result was predicted using linear mathematical models and was found to be in great agreement with the experimental results.
Abstract: The objective of this study is to present and to analyze the feasibility of using steel fibers as reinforcement in the cementations matrix to minimize the effect of free shrinkage which is a major cause of cracks that have can observe on concrete structures, also to improve the mechanical resistances of this concrete reinforced. The experimental study was performed on specimens with geometric characteristics adapted to the testing. The tests of shrinkage apply on prismatic specimens, equipped with rods fixed to the ends with different dosages of fibers, it should be noted that the fibers used are hooked end of 50mm length and 67 slenderness. The results show that the compressive strength and flexural strength increases as the degree of incorporation of fibbers increases. And the shrinkage deformations are generally less important for fibers-reinforced concrete to those appearing in the concrete without fibers.
Abstract: Natural fibers are considered to have potential use as reinforcing agents in polymer composite materials because of their principal benefits: moderate strength and stiffness, low cost, and being an environmental friendly, degradable, and renewable material. A study has been carried out to evaluate impact properties of composites made by areca fibers reinforced urea formaldehyde, melamine urea formaldehyde and epoxy resins. The extracted areca fibers from the areca husk were alkali treated with potassium hydroxide (KOH) to obtain better interfacial bonding between fiber and matrix. Then composites were produced by means of compression molding technique with varying process parameters, such as fiber condition (untreated and alkali treated), and fiber loading percentages (50% and 60% by weight). The developed areca fiber reinforced composites were then characterized by impact test. The results show that, impact strength increase with increase in the loading percentage. It is observed that, treated areca fiber reinforcement increases impact strength when compared to untreated areca fiber reinforcement.
Abstract: When concrete is exposed to high temperatures, some changes may occur in its physical and mechanical properties. Especially, high strength concrete (HSC), may exhibit damages such as cracks and spallings. To overcome this problem, incorporating polymer fibers such as polypropylene (PP) in concrete is a well-known method. In high temperatures, PP decomposes and releases harmful gases such as CO and CO2. This study researches the use of raw rice husk (RRH) as a sustainable material, instead of PP fibers considering its several favorable properties, and its usability in HSC. RRH and PP fibers were incorporated in concrete at 0.5-3% and 0.2-0.5% by weight of cement, respectively. Concrete specimens were exposed to 20 (control), 300, 600 and 900°C. Under these temperatures, residual compressive and splitting tensile strength was determined. During the high temperature effect, the amount of released harmful gases was measured by a gas detector.
Abstract: Severe damages may occur during the drilling of carbon fiber reinforced plastics (CFRP). In practice, this damage is limited by adding a backup support to the drilled parts. For some aeronautical parts with curvatures, backing up parts is a demanding process. In order to simplify the operation, this research studies the effect of using a configurable setup to support parts on the resulting quality of drilled holes. The test coupons referenced in this study are twenty four-plies unidirectional laminates made of carbon fibers and epoxy resin. Different signals were measured during the drilling process for these laminates, including the thrust force, the displacement and the acceleration. The processing of these signals demonstrated that the damage is due to the combination of two main factors: the spring-back of the thin part and the thrust force. The results found were confirmed for different feeds and speeds. When the distance between supports is increased, it is observed that the spring-back increases but the thrust force decreases. The study proves the feasibility of unsupported drilling of thin CFRP laminates without creating any observable damage.
Abstract: We constructed an atomic structure model for a PAN-based carbon fiber containing amorphous structures using molecular dynamics methods. It was found that basic physical properties such as crystallinity, Young’s modulus, and thermal conductivity of our model were nearly identical to those of real carbon fibers. We then obtained the tensile strength of a carbon fiber, which has no macro defects. We finally determined that the limitation of the tensile strength was 19 GPa.
Abstract: According to previous studies, some muscles present a non-homogeneous spatial distribution of its muscle fiber types and motor unit types. However, available muscle models only deal with muscles with homogeneous distributions. In this paper, a new architecture muscle model is proposed to permit the construction of non-uniform distributions of muscle fibers within the muscle cross section. The idea behind is the use of a motor unit placement algorithm that controls the spatial overlapping of the motor unit territories of each motor unit type. Results show the capabilities of the new algorithm to reproduce arbitrary muscle fiber type distributions.
Abstract: Nano fibers produced by electrospinning are of industrial and scientific attention due to their special characteristics such as long length, small diameter and high surface area. Applications of electrospun structures in nanotechnology are included tissue scaffolds, fibers for drug delivery, composite reinforcement, chemical sensing, enzyme immobilization, membrane-based filtration, protective clothing, catalysis, solar cells, electronic devices and others. Many polymer and ceramic precursor nano fibers have been successfully electrospun with diameters in the range from 1 nm to several microns. The process is complex so that fiber diameter is influenced by various material, design and operating parameters. The objective of this work is to apply genetic algorithm on the parameters of electrospinning which have the most significant effect on the nano fiber diameter to determine the optimum parameter values before doing experimental set up. Effective factors including initial polymer concentration, initial jet radius, electrical potential, relaxation time, initial elongation, viscosity and distance between nozzle and collector are considered to determine finest diameter which is selected by user.
Abstract: Phytophthora cinnamomi (P. c) is a plant pathogenic
oomycete that is capable of damaging plants in commercial production
systems and natural ecosystems worldwide. The most common
methods for the detection and diagnosis of P. c infection are
expensive, elaborate and time consuming. This study was carried out
to examine whether species specific and life cycle specific volatile
organic compounds (VOCs) can be absorbed by solid-phase
microextraction fibers and detected by gas chromatography that are
produced by P. c and another oomycete Pythium dissotocum. A
headspace solid-phase microextraction (HS-SPME) together with gas
chromatography (GC) method was developed and optimized for the
identification of the VOCs released by P. c. The optimized parameters
included type of fiber, exposure time, desorption temperature and
desorption time. Optimization was achieved with the analytes of P.
c+V8A and V8A alone. To perform the HS-SPME, six types of fiber
were assayed and compared: 7μm Polydimethylsiloxane (PDMS),
100μm Polydimethylsiloxane (PDMS), 50/30μm
Divinylbenzene/CarboxenTM/Polydimethylsiloxane
DVB/CAR/PDMS), 65μm Polydimethylsiloxane/Divinylbenzene
(PDMS/DVB), 85μm Polyacrylate (PA) fibre and 85μm CarboxenTM/
Polydimethylsiloxane (Carboxen™/PDMS). In a comparison of the
efficacy of the fibers, the bipolar fiber DVB/CAR/PDMS had a higher
extraction efficiency than the other fibers. An exposure time of 16h
with DVB/CAR/PDMS fiber in the sample headspace was enough to
reach the maximum extraction efficiency. A desorption time of 3min
in the GC injector with the desorption temperature of 250°C was
enough for the fiber to desorb the compounds of interest. The chromatograms and morphology study confirmed that the VOCs from
P. c+V8A had distinct differences from V8A alone, as did different
life cycle stages of P. c and different taxa such as Pythium dissotocum.
The study proved that P. c has species and life cycle specific VOCs,
which in turn demonstrated the feasibility of this method as means of
Abstract: Leprosy is an infectious disease caused by
Mycobacterium Leprae, this disease, generally, compromises
the neural fibers, leading to the development of disability.
Disabilities are changes that limit daily activities or social life
of a normal individual. When comes to leprosy, the study of
disability considered the functional limitation (physical
disabilities), the limitation of activity and social participation,
which are measured respectively by the scales: EHF, SALSA
and PARTICIPATION SCALE. The objective of this work is
to propose an on-line monitoring of leprosy patients, which is
based on information scales EHF, SALSA and
PARTICIPATION SCALE. It is expected that the proposed
system is applied in monitoring the patient during treatment
and after healing therapy of the disease. The correlations that
the system is between the scales create a variety of
information, presented the state of the patient and full of
changes or reductions in disability. The system provides
reports with information from each of the scales and the
relationships that exist between them. This way, health
professionals, with access to patient information, can
intervene with techniques for the Prevention of Disability.
Through the automated scale, the system shows the level of
the patient and allows the patient, or the responsible, to take a
preventive measure. With an online system, it is possible take
the assessments and monitor patients from anywhere.
Abstract: Nowadays, consumption of whole flours and flours
with high extraction rate is recommended, because of their high
amount of fibers, vitamins and minerals. Despite nutritional benefits
of whole flour, concentration of some undesirable components such
as phytic acid is higher than white flour. In this study, effect of
several lactic acid bacteria sourdough on Toast bread is investigated.
Sourdough from lactic acid bacteria (Lb. plantarum, Lb. reuteri) with
different dough yield (250 and 300) is made and incubated at 30°C
for 20 hour, then added to dough in the ratio of 10, 20 and 30%
replacement. Breads that supplemented with Lb. plantarum
sourdough had lower phytic acid. Higher replacement of sourdough
and higher DY cause higher decrease in phytic acid content.
Sourdough from Lb. plantarum, DY = 300 and 30% replacement
cause the highest decrease in phytic acid content (49.63 mg/100g).
As indicated by panelists, Lb. reuteri sourdough can present the
greatest effect on overall quality score of the breads. DY reduction
cause a decrease in bread quality score. Sensory score of Toast bread
is 81.71 in the samples that treated with Lb. reuteri sourdough with
DY = 250 and 20% replacement.
Abstract: Propagation of solitons in single-mode birefringent fibers is considered under the presence of third-order dispersion (TOD). The behavior of two neighboring solitons and their interaction is investigated under the presence of third-order dispersion with different group velocity dispersion (GVD) parameters. It is found that third-order dispersion makes the resultant soliton to deviate from its ideal position and increases the interaction between adjacent soliton pulses. It is also observed that this deviation due to third-order dispersion is considerably small when the optical pulse propagates at wavelengths relatively far from the zerodispersion. Modified coupled nonlinear Schrödinger-s equations (CNLSE) representing the propagation of optical pulse in single mode fiber with TOD are solved using split-step Fourier algorithm. The results presented in this paper reveal that the third-order dispersion can substantially increase the interaction between the solitons, but large group velocity dispersion reduces the interaction between neighboring solitons.
Abstract: Nylon 6-clay hybrid/neat nylon 6, sheath/core
bicomponent nanocomposite fibers containing 4 wt% of clay in
sheath section were melt spun at different take-up speeds. Their
orientation and crystalline structure were compared to those of neat
nylon 6 fibers. Birefringence measurements showed that the
orientation development in sheath and core parts of bicomponent
fibers was different. Crystallinity results showed that clay did not act
as a nucleating agent for bicomponent fibers. The neat nylon 6 fiber
had a smooth surface while striped pattern was appeared on the
surface of bicomponent fiber containing clay due to thermal
shrinkage of the core part.
Abstract: This paper studies the optimum design for reducing
optical loss of an 8x8 mechanical type optical switch due to the
temperature change. The 8x8 optical switch is composed of a base, 8
input fibers, 8 output fibers, 3 fixed mirrors and 17 movable mirrors.
First, an innovative switch configuration is proposed with
thermal-compensated design. Most mechanical type optical switches
have a disadvantage that their precision and accuracy are influenced
by the ambient temperature. Therefore, the thermal-compensated
design is to deal with this situation by using materials with different
thermal expansion coefficients (α). Second, a parametric modeling
program is developed to generate solid models for finite element
analysis, and the thermal and structural behaviors of the switch are
analyzed. Finally, an integrated optimum design program, combining
Autodesk Inventor Professional software, finite element analysis
software, and genetic algorithms, is developed for improving the
thermal behaviors that the optical loss of the switch is reduced. By
changing design parameters of the switch in the integrated design
program, the final optimum design that satisfies the design constraints
and specifications can be found.
Abstract: Viscous heating becomes significant in the high speed
resin coating process of glass fibers for optical fiber manufacturing.
This study focuses on the coating resin flows inside the capillary
coating die of optical fiber coating applicator and they are numerically
simulated to examine the effects of viscous heating and subsequent
temperature increase in coating resin. Resin flows are driven by fast
moving glass fiber and the pressurization at the coating die inlet, while
the temperature dependent viscosity of liquid coating resin plays an
important role in the resin flow. It is found that the severe viscous
heating near the coating die wall profoundly alters the radial velocity
profiles and that the increase of final coating thickness by die
pressurization is amplified if viscous heating is present.
Abstract: Carbon fibers have specific characteristics in
comparison with industrial and structural materials used in different
applications. Special properties of carbon fibers make them attractive
for reinforcing and fabrication of composites. These fibers have been
utilized for composites of metals, ceramics and plastics. However,
it-s mainly used in different forms to reinforce lightweight polymer
materials such as epoxy resin, polyesters or polyamides. The
composites of carbon fiber are stronger than steel, stiffer than
titanium, and lighter than aluminum and nowadays they are used in a
variety of applications. This study explains applications of carbon
fibers in different fields such as space, aviation, transportation,
medical, construction, energy, sporting goods, electronics, and the
other commercial/industrial applications. The last findings of
composites with polymer, metal and ceramic matrices containing
carbon fibers and their applications in the world investigated.
Researches show that carbon fibers-reinforced composites due to
unique properties (including high specific strength and specific
modulus, low thermal expansion coefficient, high fatigue strength,
and high thermal stability) can be replaced with common industrial
and structural materials.
Abstract: Nowadays due to globalization of economy and
competition environment, innovation and technology plays key role
at creation of wealth and economic growth of countries. In fact
prompt growth of practical and technologic knowledge may results in
social benefits for countries when changes into effective innovation.
Considering the importance of innovation for the development of
countries, this study addresses the radical technological innovation
introduced by nanopapers at different stages of producing paper
including stock preparation, using authorized additives, fillers and
pigments, using retention, calender, stages of producing conductive
paper, porous nanopaper and Layer by layer self-assembly. Research
results show that in coming years the jungle related products will lose
considerable portion of their market share, unless embracing radical
innovation. Although incremental innovations can make this industry
still competitive in mid-term, but to have economic growth and
competitive advantage in long term, radical innovations are
necessary. Radical innovations can lead to new products and
materials which their applications in packaging industry can produce
value added. However application of nanotechnology in this industry
can be costly, it can be done in cooperation with other industries to
make the maximum use of nanotechnology possible. Therefore this
technology can be used in all the production process resulting in the
mass production of simple and flexible papers with low cost and
special properties such as facility at shape, form, easy transportation,
light weight, recovery and recycle marketing abilities, and sealing.
Improving the resistance of the packaging materials without reducing
the performance of packaging materials enhances the quality and the
value added of packaging. Improving the cellulose at nano scale can
have considerable electron optical and magnetic effects leading to
improvement in packaging and value added. Comparing to the
specifications of thermoplastic products and ordinary papers,
nanopapers show much better performance in terms of effective
mechanical indexes such as the modulus of elasticity, tensile strength,
and strain-stress. In densities lower than 640 kgm -3, due to the
network structure of nanofibers and the balanced and randomized
distribution of NFC in flat space, these specifications will even
improve more. For nanopapers, strains are 1,4Gpa, 84Mpa and 17%,
13,3 Gpa, 214Mpa and 10% respectively. In layer by layer self
assembly method (LbL) the tensile strength of nanopaper with Tio3
particles and Sio2 and halloysite clay nanotube are 30,4 ±7.6Nm/g
and 13,6 ±0.8Nm/g and 14±0.3,3Nm/g respectively that fall within
acceptable range of similar samples with virgin fiber. The usage of
improved brightness and porosity index in nanopapers can create
more competitive advantages at packaging industry.
Abstract: The objective of this work was to investigate flow
properties of powdered infant formula samples. Samples were
purchased at a local pharmacy and differed in composition. Lactose
free infant formula, gluten free infant formula and infant formulas
containing dietary fibers and probiotics were tested and compared
with a regular infant formula sample which did not contain any of
these supplements. Particle size and bulk density were determined
and their influence on flow properties was discussed. There were no
significant differences in bulk densities of the samples, therefore the
connection between flow properties and bulk density could not be
determined. Lactose free infant formula showed flow properties
different to standard supplement-free sample. Gluten free infant
formula with addition of probiotic microorganisms and dietary fiber
had the narrowest particle size distribution range and exhibited the
best flow properties. All the other samples exhibited the same
tendency of decreasing compaction coefficient with increasing flow
speed, which means they all become freer flowing with higher flow
speeds.
Abstract: In this paper, an analytical approach is used to study the coupled lateral-torsional vibrations of laminated composite beam. It is known that in such structures due to the fibers orientation in various layers, any lateral displacement will produce a twisting moment. This phenomenon is modeled by the bending-twisting material coupling rigidity and its main feature is the coupling of lateral and torsional vibrations. In addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies. Then, the governing differential equations are derived using the Hamilton-s principle and the mathematical model matches the Timoshenko beam model when neglecting the effect of bending-twisting rigidity. The equations of motion which form a system of three coupled PDEs are solved analytically to study the free vibrations of the beam in lateral and rotational modes due to the bending, as well as the torsional mode caused by twisting. The analytic solution is carried out in three steps: 1) assuming synchronous motion for the kinematic variables which are the lateral, rotational and torsional displacements, 2) solving the ensuing eigenvalue problem which contains three coupled second order ODEs and 3) imposing different boundary conditions related to combinations of simply, clamped and free end conditions. The resulting natural frequencies and mode shapes are compared with similar results in the literature and good agreement is achieved.
Abstract: A simple microstructure optical fiber design based on an octagonal cladding structure is presented for simultaneously controlling dispersion and leakage properties. The finite difference method with anisotropic perfectly matched boundary layer is used to investigate the guiding properties. It is demonstrated that octagonal photonic crystal fibers with four rings can assume negative ultra-flattened dispersion of -19 + 0.23 ps/nm/km in the wavelength range of 1.275 μm to 1.68 μm, nearly zero ultra-flattened dispersion of 0 ± 0.40 ps/nm/km in a 1.38 to 1.64 μm, and low confinement losses less than 10-3 dB/km in the entire band of interest.