Abstract: This study presents an investigation of
electrochemical variables and an application of the optimal
parameters in operating a continuous upflow electrocoagulation
reactor in removing dye. Direct red 23, which is azo-based, was used
as a representative of direct dyes. First, a batch mode was employed
to optimize the design parameters: electrode type, electrode distance,
current density and electrocoagulation time. The optimal parameters
were found to be iron anode, distance between electrodes of 8 mm
and current density of 30 A·m-2 with contact time of 5 min. The
performance of the continuous upflow reactor with these parameters
was satisfactory, with >95% color removal and energy consumption
in the order of 0.6-0.7 kWh·m-3.
Abstract: A first intermediate roll of Sendzirmir mills was failure
by surface spalling during operation. After analyzing by visual, stereo
microscope, optical microscope, scanning electron microscope,
glow-discharged spectrometer and hardness test, respectively, the
results show that some voids and cracks existed on the contact surface
as well as subsurface. Further examination verified inadequate
hardness and inclusions were responsible for the failure of surface
spalling.
Abstract: Cast metal inlays can be used on molars requiring a
class II restoration instead amalgam and offer a durable alternative.
Because it is known that class II inlays may increase the
susceptibility to fracture, it is important to ensure optimal
performance in selection of the adequate preparation design to reduce
stresses in teeth structures and also in the restorations. The aim of the
study was to investigate the influence of preparation design on stress
distribution in molars with different class II preparations and in cast
metal inlays. The first step of the study was to achieve 3D models in
order to analyze teeth and cast metal class II inlays. The geometry of
the intact tooth was obtained by 3D scanning using a manufactured
device. With a NURBS modeling program the preparations and the
appropriately inlays were designed. 3D models of first upper molars
of the same shape and size were created. Inlay cavities designs were
created using literature data. The geometrical model was exported
and the mesh structure of the solid 3D model was created for
structural simulations. Stresses were located around the occlusal
contact areas. For the studied cases, the stress values were not
significant influenced by the taper of the preparation. it was
demonstrated stresses are higher in the cast metal restorations and
therefore the strength of the teeth is not affected.
Abstract: To understand the seismic behavior of the offshore
structures, the dynamic interaction of the water-structure-soil should
be assessed. In this regard the role of the water dynamic properties in
magnifying or reducing of the effects of earthquake induced motions
on offshore structures haven't been investigated in precise manner in
available literature. In this paper the sea water level fluctuations
effects on the seismic behavior of a sample of offshore structures has
been investigated by emphasizing on the water-structure interaction
phenomenon. For this purpose a two dimensional finite element
model of offshore structures as well as surrounded water has been
developed using ANSYS software. The effect of soil interaction with
embedded pile foundation has been imposed by using a series of
nonlinear springs in horizontal and vertical directions in soil-piles
contact points. In the model, the earthquake induced motions have
been applied on springs and consequently the motions propagated
upward to the structure and surrounded water. As a result of
numerical study, the horizontal deformations of the offshore deck as
well as internal force and buckling coefficient in structural elements
have been recorded and controlled with and without water presence.
In part of study a parametric study has been accomplished on sea
water level fluctuations and effect of this parameter has been studied
on the aforementioned numerical results.
Abstract: Bentonitic material from South Aswan, Egypt was evaluated in terms of mineral-ogy and chemical composition as bleaching clay in refining of transformer oil before and after acid activation and thermal treatment followed by acid leaching using HCl and H2SO4 for different contact times. Structural modification and refining power of bento-nite were investigated during modification by means of X-ray diffraction and infrared spectroscopy. The results revealed that the activated bentonite could be used for refining of transformer oil. The oil parameters such as; dielectric strength, viscosity and flash point had been improved. The dielectric breakdown strength of used oil increased from 29 kV for used oil treated with unactivated bentonite to 74 kV after treatment with activated bentonite. Kinematic Viscosity changed from 19 to 11 mm2 /s after treatment with activated bentonite. However, flash point achieved 149 ºC.
Abstract: The experimental thermal performance of two heat
exchangers in closed-wet cooling tower (CWCT) was investigated in
this study. The test sections are heat exchangers which have multi path
that is used as the entrance of cooling water and are consisting of
bare-type copper tubes between 15.88mm and 19.05mm. The process
fluids are the cooling water that flows from top part of heat exchanger
to bottom side in the inner side of tube, and spray water that flows
gravitational direction in the outer side of it. Air contacts its outer side
of that as it counterflows. Heat and mass transfer coefficients and
cooling capacity were calculated with variations of process fluids,
multi path and different diameter tubes to figure out the performance
of characteristics of CWCT.
The main results were summarized as follows: The results show this
experiment is reliable with values of heat and mass transfer
coefficients comparing to values of correlations. Heat and mass
transfer coefficients and cooling capacity of two paths are higher than
these with one path using 15.88 and 19.05mm tubes. Cooling capacity
per unit volume with 15.88mm tube using one and two paths are
higher than 19.05mm tube due to increase of surface area per unit
volume.
Abstract: The fixed partial dentures are mainly used in the frontal
part of the dental arch because of their great esthetics. There are
several factors that are associated with the stress state created in
ceramic restorations, including: thickness of ceramic layers,
mechanical properties of the materials, elastic modulus of the
supporting substrate material, direction, magnitude and frequency of
applied load, size and location of occlusal contact areas, residual
stresses induced by processing or pores, restoration-cement
interfacial defects and environmental defects. The purpose of this
study is to evaluate the capability of Polarization Sensitive Optical
Coherence Tomography (PSOCT) in detection and analysis of
possible material defects in metal-ceramic and integral ceramic fixed
partial dentures. As a conclusion, it is important to have a non
invasive method to investigate fixed partial prostheses before their
insertion in the oral cavity in order to satisfy the high stress
requirements and the esthetic function.
Abstract: The present study attempted to improve the Mercury
(Hg) sorption capacity of kanuma volcanic ash soil (KVAS) by
impregnating the cupper (Cu). Impregnation was executed by 1 and
5% Cu powder and sorption characterization of optimum Hg
removing Cu impregnated KVAS was performed under different
operational conditions, contact time, solution pH, sorbent dosage and
Hg concentration using the batch operation studies. The 1% Cu
impregnated KVAS pronounced optimum improvement (79%) in
removing Hg from water compare to control. The present
investigation determined the equilibrium state of maximum Hg
adsorption at 6 h contact period. The adsorption revealed a pH
dependent response and pH 3.5 showed maximum sorption capacity
of Hg. Freundlich isotherm model is well fitted with the experimental
data than that of Langmuir isotherm. It can be concluded that the Cu
impregnation improves the Hg sorption capacity of KVAS and 1%
Cu impregnated KVAS could be employed as cost-effective
adsorbent media for treating Hg contaminated water.
Abstract: In this study, the adhesion of ice to solid substrates
with different surface properties is compared. Clear ice, similar to
atmospheric in-flight icing encounters, is accreted on the different
substrates under controlled conditions. The ice adhesion behavior is
investigated by means of a dynamic vibration testing technique with
an electromagnetic shaker initiating ice de-bonding in the interface
between the substrate and the ice. The results of the experiments
reveal that the affinity for ice accretion is significantly influenced by
the water contact angle of the respective sample.
Abstract: This paper is concerned with an investigation into the
localized non-stability of a thin elastic orthotropic semi-infinite plate.
In this study, a semi-infinite plate, simply supported on two edges
and different boundary conditions, clamped, hinged, sliding contact
and free on the other edge, are considered. The mathematical model
is used and a general solution is presented the conditions under which
localized solutions exist are investigated.
Abstract: Interaction of inorganic water-soluble salts and building stones is studied in the paper. Two types of sandstone and one type of spongillite as representatives of materials used in historical masonry are subjected to experimental testing. Within the performed experiments, measurement of moisture and chloride concentration profiles is done in order to get input data for computational inverse analysis. Using the inverse analysis, moisture diffusivity and chloride diffusion coefficient of investigated materials are accessed. Additionally, the effect of salt presence on water vapor storage is investigated using dynamic vapor sorption device. The obtained data represents valuable information for restoration of historical masonry and give evidence on the performance of studied stones in contact with water soluble salts.
Abstract: Relevant agricultural information disseminator
(extension agent) ratio of 1:3500 farm families which become a
menace to agricultural production capacity in developing countries
necessitate this study. Out of 4 zones in the state, 24 extension agents
in each zone, 4 extension agents using cell phones and 120 farmers
using cell phone and 120 other farmers not using cell phone were
purposively selected to give 240 farmers that participated in the
research. Data were collected using interview guide and analysized
using frequency, percentage and t-test.. Frequency of contact with
agricultural information centers revealed that cell phone user farmers
had greater means score of X 41.43 contact as against the low mean
X19.32 contact recorded by farmers receiving agricultural
information from extension agents not using cell phone and their
production was statistically significant at P < 0.05. Usage of cell
phone increase extension agent contact and increase farmers-
production capacity.
Abstract: In this paper, a generalized self-consistent scheme, or “three phase model", is used to set up a micro-mechanics model for rough surface contact with randomly distributed asperities. The dimensionless average real pressure p is obtained as function of the ratio of the real contact area to the apparent contact area, 0 A / A r . Both elastic and plastic materials are considered, and the influence of the plasticity of material on p is discussed. Both two-dimensional and three-dimensional rough surface contact problems are considered.
Abstract: To achieve accurate and precise results of finite
element analysis (FEA) of bones, it is important to represent the
load/boundary conditions as identical as possible to the human body
such as the bone properties, the type and force of the muscles, the
contact force of the joints, and the location of the muscle attachment.
In this study, the difference in the Von-Mises stress and the total
deformation was compared by classifying them into Case 1, which
shows the actual anatomical form of the muscle attached to the femur
when the same muscle force was applied, and Case 2, which gives a
simplified representation of the attached location. An inverse
dynamical musculoskeletal model was simulated using data from an
actual walking experiment to complement the accuracy of the
muscular force, the input value of FEA. The FEA method using the
results of the muscular force that were calculated through the
simulation showed that the maximum Von-Mises stress and the
maximum total deformation in Case 2 were underestimated by 8.42%
and 6.29%, respectively, compared to Case 1. The torsion energy and
bending moment at each location of the femur occurred via the stress
ingredient. Due to the geometrical/morphological feature of the femur
of having a long bone shape when the stress distribution is wide, as
shown in Case 1, a greater Von-Mises stress and total deformation are
expected from the sum of the stress ingredients. More accurate results
can be achieved only when the muscular strength and the attachment
location in the FEA of the bones and the attachment form are the same
as those in the actual anatomical condition under the various moving
conditions of the human body.
Abstract: Nowadays, computer worms, viruses and Trojan horse
become popular, and they are collectively called malware. Those
malware just spoiled computers by deleting or rewriting important
files a decade ago. However, recent malware seems to be born to earn
money. Some of malware work for collecting personal information so
that malicious people can find secret information such as password for
online banking, evidence for a scandal or contact address which relates
with the target. Moreover, relation between money and malware
becomes more complex. Many kinds of malware bear bots to get
springboards. Meanwhile, for ordinary internet users,
countermeasures against malware come up against a blank wall.
Pattern matching becomes too much waste of computer resources,
since matching tools have to deal with a lot of patterns derived from
subspecies. Virus making tools can automatically bear subspecies of
malware. Moreover, metamorphic and polymorphic malware are no
longer special. Recently there appears malware checking sites that
check contents in place of users' PC. However, there appears a new
type of malicious sites that avoids check by malware checking sites. In
this paper, existing protocols and methods related with the web are
reconsidered in terms of protection from current attacks, and new
protocol and method are indicated for the purpose of security of the
web.
Abstract: The feasibility of applying a simple and cost effective sliding friction testing apparatus to study the friction behaviour of a clutch facing material, effected by the variation of temperature and contact pressure, was investigated. It was found that the method used in this work was able to give a convenient and cost effective measurement of friction coefficients and their transitions of a clutch facing material. The obtained results will be useful for the development process of new facing materials.
Abstract: In Indonesia, goat milk is often consumed and
believed as anti-allergy. The objective of this research was to study
the effect of goat milk and their fractions (casein and whey)
supplementation on total serum IgE concentrations and leukocytes
count in rat sensitized with contact allergen dinitrochlorobenzene
(DNCB). Female Wistar rats 6-8 weeks old were divided into four
groups: 1) whey, 2) casein, 3) whole milk supplementation and 4)
phosphate-buffered saline/PBS (control). The results showed that
supplementation of goat milk on rats did not affects on total serum
IgE concentrations and number of leukocytes. After sensitized with
DNCB, the monocyte percentage in rats was higher (P
Abstract: With the rapid growth and development of information and communication technology, the Internet has played a definite and irreplaceable role in people-s social lives in Taiwan like in other countries. In July 2008, on a general social website, an unexpected phenomenon was noticed – that there were more than one hundred users who started forming clubs voluntarily and having face-to-face gatherings for specific purposes. In this study, it-s argued whether or not teenagers- social contact on the Internet is involved in their life context, and tried to reveal the teenagers- social preferences, values, and needs, which merge with and influence teenagers- social activities. Therefore, the study conducts multiple user experience research methods, which include practical observations and qualitative analysis by contextual inquiries and in-depth interviews. Based on the findings, several design implications for software related to social interactions and cultural inheritance are offered. It is concluded that the inherent values of a social behaviors might be a key issue in developing computer-mediated communication or interaction designs in the future.
Abstract: The present work was conducted for the synthesis of
nano size zerovalent iron (nZVI) and hexavalent chromium (Cr(VI))
removal as a highly toxic pollutant by using this nanoparticles. Batch
experiments were performed to investigate the effects of Cr(VI),
nZVI concentration, pH of solution and contact time variation on
the removal efficiency of Cr(VI). nZVI was synthesized by
reduction of ferric chloride using sodium borohydrid. SEM and
XRD examinations applied for determination of particle size and
characterization of produced nanoparticles. The results showed that
the removal efficiency decreased with Cr(VI) concentration and pH
of solution and increased with adsorbent dosage and contact time.
The Langmuir and Freundlich isotherm models were used for the
adsorption equilibrium data and the Langmuir isotherm model was
well fitted. Nanoparticle ZVI presented an outstanding ability to
remove Cr(VI) due to high surface area, low particle size and high
inherent activity.
Abstract: This paper numerically investigates the effects of input
speed on the overall dynamic characteristics of a multi-body system
with differently located revolute clearance joints without friction. A
typical planar slider-crank mechanism is used as a demonstration case
in which the effects of the input speed on the dynamic performance
of the mechanism with a revolute clearance joint between the crank
and connecting rod, and between the connecting rod and slider are
separately investigated with comprehensive observations numerically
presented. It is observed that, changing the driving speed of a multibody
system makes the behavior of the system to change from
either periodic to chaotic, or chaotic to periodic depending on which
joint has clearance. The location of the clearance revolute joint and
the operating speed of a multi-body system play a crucial role in
predicting accurately the dynamic responses of the system. Therefore
the dynamic behavior of one clearance revolute joint cannot be used
as a general case for a mechanical system.