Abstract: This paper presents an experimental investigation of
transformer dielectric response and solid insulation water content.
The dielectric response was carried out on the base of Hybrid
Frequency Dielectric Spectroscopy and Polarization Current
measurements method (FDS &PC). The calculation of the water
content in paper is based on the water content in oil and the obtained
equilibrium curves. A reference measurements were performed at
equilibrium conditions for water content in oil and paper of
transformer at different stable temperatures (25, 50, 60 and 70°C) to
prepare references to evaluate the insulation behavior at the not
equilibrium conditions. Some measurements performed at the
different simulated normal working modes of transformer operation
at the same temperature where the equilibrium conditions. The
obtained results show that when transformer temperature is mach
more than the its ambient temperature, the transformer temperature
decreases immediately after disconnecting the transformer from the
network and this temperature reduction influences the transformer
insulation condition in the measuring process. In addition to the oil
temperature at the near places to the sensors, the temperature
uniformity in transformer which can be changed by a big change in
the load of transformer before the measuring time will influence the
result. The investigations have shown that the extremely influence of
the time between disconnecting the transformer and beginning the
measurements on the results. And the online monitoring for water
content in paper measurements, on the basis of the oil water content
on line monitoring and the obtained equilibrium curves. The
measurements where performed continuously and for about 50 days
without any disconnection in the prepared the adiabatic room.
Abstract: Monitoring of microbial flora in aquacultured sea bream, in relation to the physicochemical parameters of the rearing seawater, ended to a model describing the influence of the last to the quality of the fisheries. Fishes were sampled during eight months from four aqua farms in Western Greece and analyzed for psychrotrophic, H2S producing bacteria, Salmonella sp., heterotrophic plate count (PCA), with simultaneous physical evaluation. Temperature, dissolved oxygen, pH, conductivity, TDS, salinity, NO3 - and NH4 + ions were recorded. Temperature, dissolved oxygen and conductivity were correlated, respectively, to PCA, Pseudomonas sp. and Shewanella sp. counts. These parameters were the inputs of the model, which was driving, as outputs, to the prediction of PCA, Vibrio sp., Pseudomonas sp. and Shewanella sp. counts, and fish microbiological quality. The present study provides, for the first time, a ready-to-use predictive model of fisheries hygiene, leading to an effective management system for the optimization of aquaculture fisheries quality.
Abstract: Regarding previous research studies it was concluded
that thin-walled fiber-cement composites are able to conduct electric
current under specific conditions. This property is ensured by using
of various kinds of carbon materials. Though carbon fibers are less
conductive than metal fibers, composites with carbon fibers were
evaluated as better current conductors than the composites with metal
fibers. The level of electric conductivity is monitored by the means of
impedance measurement of designed samples. These composites
could be used for a range of applications such as heating of
trafficable surfaces or shielding of electro-magnetic fields.
The aim of the present research was to design an element with the
ability to monitor internal processes in building structures and
prevent them from collapsing. As a typical element for laboratory
testing there was chosen a concrete column, which was repeatedly
subjected to load by simple pressure with continual monitoring of
changes in electrical properties.
Abstract: Ionanofluids are a new and innovative class of heat transfer fluids which exhibit fascinating thermophysical properties compared to their base ionic liquids. This paper deals with the findings of thermal conductivity and specific heat capacity of ionanofluids as a function of a temperature and concentration of nanotubes. Simulation results using ionanofluids as coolants in heat exchanger are also used to access their feasibility and performance in heat transfer devices. Results on thermal conductivity and heat capacity of ionanofluids as well as the estimation of heat transfer areas for ionanofluids and ionic liquids in a model shell and tube heat exchanger reveal that ionanofluids possess superior thermal conductivity and heat capacity and require considerably less heat transfer areas as compared to those of their base ionic liquids. This novel class of fluids shows great potential for advanced heat transfer applications.
Abstract: The onset of Marangoni convection in a horizontal
fluid layer with internal heat generation overlying a solid layer
heated from below is studied. The upper free surface of a fluid is
nondeformable and the bottom boundary are rigid and no-slip. The
resulting eigenvalue problem is solved exactly. The critical values of
the Marangoni numbers for the onset of Marangoni convection are
calculated and the latter is found to be critically dependent on the
internal heating, depth ratio and conductivity ratio. The effects of the
thermal conductivity and the thickness of the solid plate on the onset
of convective instability with internal heating are studied in detail.
Abstract: Radiofrequency (RF) lesioning of nerves have been commonly used to alleviate chronic pain, where RF current preventing transmission of pain signals through the nerve by heating the nerve causing the pain. There are some factors that affect the temperature distribution and the nerve lesion size, one of these factors is the inhomogeneities in the tissue medium. Our objective is to calculate the temperature distribution and the nerve lesion size in an inhomogeneous medium surrounding the RF electrode. A two 3-D finite element models are used to compare the temperature distribution in the homogeneous and inhomogeneous medium. Also the effect of temperature-dependent electric conductivity on maximum temperature and lesion size is observed. Results show that the presence of an inhomogeneous medium around the RF electrode has a valuable effect on the temperature distribution and lesion size. The dependency of electric conductivity on tissue temperature increased lesion size.
Abstract: This study presents the improvement of thermal
performance of heat pipe using copper nanofluid with aqueous
solution of n-Butanol. The nanofluids kept in the suspension of
conventional fluids have the potential of superior heat transfer
capability than the conventional fluids due to their improved thermal
conductivity. In this work, the copper nanofluid which has a 40 nm
size with a concentration of 100 mg/lit is kept in the suspension of
the de-ionized (DI) water and an aqueous solution of n-Butanol and
these fluids are used as a working medium in the heat pipe. The study
discusses about the effect of heat pipe inclination, type of working
fluid and heat input on the thermal efficiency and thermal resistance.
The experimental results are evaluated in terms of its performance
metrics and are compared with that of DI water.
Abstract: This study was designed to formulate,
pharmaceutically evaluate a topical skin-care cream (w/o emulsion)
of Aloe Vera versus its vehicle (Base) as control and determine their
effects on Stratum Corneum (SC) water content and Transepidermal
water loss (TEWL). Base containing no extract and a Formulation
containing 3% concentrated extract of Aloe Vera was developed by
entrapping in the inner aqueous phase of w/o emulsion (cream).
Lemon oil was incorporated to improve the odor. Both the Base and
Formulation were stored at 8°C ±0.1°C (in refrigerator), 25°C±0.1°C,
40°C±0.1°C and 40°C± 0.1°C with 75% RH (in incubator) for a
period of 4 weeks to predict their stability. The evaluation parameters
consisted of color, smell, type of emulsion, phase separation,
electrical conductivity, centrifugation, liquefaction and pH. Both the
Base and Formulation were applied to the cheeks of 21 healthy
human volunteers for a period of 8 weeks Stratum corneum (SC)
water content and Transepidermal water loss (TEWL) were
monitored every week to measure any effect produced by these
topical creams. The expected organoleptic stability of creams was
achieved from 4 weeks in-vitro study period. Odor was disappeared
with the passage of time due to volatilization of lemon oil. Both the
Base and Formulation produced significant (p≤0.05) changes in
TEWL with respect to time. SC water content was significantly
(p≤0.05) increased by the Formulation while the Base has
insignificant (p 0.05) effects on SC water content. The newly
formulated cream of Aloe Vera, applied is suitable for improvement
and quantitative monitoring of skin hydration level (SC water
content/ moisturizing effects) and reducing TEWL in people with dry
skin.
Abstract: Unsteady natural convection and heat transfer in a square cavity partially filled with porous media using a thermal
non-equilibrium model is studied in this paper. The left vertical wall is
maintained at a constant hot temperature Th and the right vertical wall
is maintained at a constant cold temperature Tc, while the horizontal
walls are adiabatic. The governing equations are obtained by applying
the Darcy model and Boussinesq approximation. COMSOL’s finite
element method is used to solve the non-dimensional governing
equations together with specified boundary conditions. The governing
parameters of this study are the Rayleigh number (Ra = 10^5, and Ra = 10^6 ), Darcy namber (Da = 10^−2, and Da = 10^−3),
the modified thermal conductivity ratio (10^−1 ≤ γ ≤ 10^4), the inter-phase heat transfer coefficien (10^−1 ≤ H ≤ 10^3) and the
time dependent (0.001 ≤ τ ≤ 0.2). The results presented for
values of the governing parameters in terms of streamlines in both
fluid/porous-layer, isotherms of fluid in fluid/porous-layer, isotherms
of solid in porous layer, and average Nusselt number.
Abstract: Synthetic juice clarification was done through spiral
wound ultrafiltration (UF) membrane module. Synthetic juice was
clarified at two different operating conditions, such as, with and
without permeates recycle at turbulent flow regime. The performance
of spiral wound ultrafiltration membrane was analyzed during
clarification of synthetic juice. Synthetic juice was the mixture of
deionized water, sucrose and pectin molecule. The operating
conditions are: feed flowrate of 10 lpm, pressure drop of 413.7 kPa
and Reynolds no of 5000. Permeate sample was analyzed in terms of
volume reduction factor (VRF), viscosity (Pa.s), ⁰Brix, TDS (mg/l),
electrical conductivity (μS) and turbidity (NTU). It was observe that
the permeate flux declined with operating time for both conditions of
with and without permeate recycle due to increase of concentration
polarization and increase of gel layer on membrane surface. For
without permeate recycle, the membrane fouling rate was faster
compared to with permeate recycle. For without permeate recycle,
the VRF rose up to 5 and for with recycle permeate the VRF is 1.9.
The VRF is higher due to adsorption of solute (pectin) molecule on
membrane surface and resulting permeateflux declined with VRF.
With permeate recycle, quality was within acceptable limit. Fouled
membrane was cleaned by applying different processes (e.g.,
deionized water, SDS and EDTA solution). Membrane cleaning was
analyzed in terms of permeability recovery.
Abstract: Nanocrystalline thin film of Na0.1V2O5.nH2O xerogel
obtained by sol gel synthesis was used as gas sensor. Gas sensing
properties of different gases such as hydrogen, petroleum and
humidity were investigated. Applying XRD and TEM the size of the
nanocrystals is found to be 7.5 nm. SEM shows a highly porous
structure with submicron meter-sized voids present throughout the
sample. FTIR measurement shows different chemical groups
identifying the obtained series of gels. The sample was n-type
semiconductor according to the thermoelectric power and electrical
conductivity. It can be seen that the sensor response curves from
130oC to 150oC show a rapid increase in sensitivity for all types of
gas injection, low response values for heating period and the rapid
high response values for cooling period. This result may suggest that
this material is able to act as gas sensor during the heating and
cooling process.
Abstract: This experiment discusses the effects of fracture
parameters such as depth, length, width, angle and the number of the
fracture to the conductance properties of laterite using the DUK-2B
digital electrical measurement system combined with the method of
simulating the fractures. The results of experiment show that the
changes of fracture parameters produce effects to the conductance
properties of laterite. There is a clear degressive period of the
conductivity of laterite during increasing the depth, length, width, or
the angle and the quantity of fracture gradually. When the depth of
fracture exceeds the half thickness of the soil body, the conductivity of
laterite shows evidently non-linear diminishing pattern and the
amplitude of decrease tends to increase. The length of fracture has
fewer effects than the depth to the conductivity. When the width of
fracture reaches some fixed values, the change of the conductivity is
less sensitive to the change of the width, and at this time, the
conductivity of laterite maintains at a stable level. When the angle of
fracture is less than 45°, the decrease of the conductivity is more
clearly as the angle increases. But when angle is more than 45°,
change of the conductivity is relatively gentle as the angle increases.
The increasing quantity of the fracture causes the other fracture
parameters having great impact on the change of conductivity. When
moisture content and temperature were unchanged, depth and angle of
fractures are the major factors affecting the conductivity of laterite
soil; quantity, length, and width are minor influencing factors. The
sensitivity of fracture parameters affect conductivity of laterite soil is:
depth >angles >quantity >length >width.
Abstract: Aggregation behavior of sodium salicylate and sodium cumene sulfonate was studied in aqueous solution at different temperature. Specific conductivity and relative viscosity were measured at different temperature to find minimum hydrotropic concentration. The thermodynamic parameters (free energy, enthalpy and entropy) were evaluated in the temperature range of 30°C-70°C. The free energy decreased with increase in temperature. The aggregation was found to be exothermic in nature and favored by positive value of entropy.
Abstract: In this study, Li4SiO4 powder was successfully
synthesized via sol gel method followed by drying at 150oC. Lithium
oxide, Li2O and silicon oxide, SiO2 were used as the starting
materials with citric acid as the chelating agent. The obtained powder
was then sintered at various temperatures. Crystallographic phase
analysis, morphology and ionic conductivity were investigated
systematically employing X-ray diffraction, Fourier Transform
Infrared, Scanning Electron Microscopy and AC impedance
spectroscopy. XRD result showed the formation of pure monoclinic
Li4SiO4 crystal structure with lattice parameters a = 5.140 Å, b =
6.094 Å, c = 5.293 Å, β = 90o in the sample sintered at 750oC. This
observation was confirmed by FTIR analysis. The bulk conductivity
of this sample at room temperature was 3.35 × 10-6 S cm-1 and the
highest bulk conductivity of 1.16 × 10-4 S cm-1 was obtained at
100°C. The results indicated that, the Li4SiO4 compound has
potential to be used as host for LISICON structured solid electrolyte
for low temperature application.
Abstract: This study was conducted to evaluate factors
regulating groundwater quality in an area with agriculture as main
use. Under this study twelve groundwater samples have been
collected from Padra taluka, Dabhoi taluka and Savli taluka of
Vadodara district. Groundwater samples were chemically analyzed
for major physicochemical parameter in order to understand the
different geochemical processes affecting the groundwater quality.
The analytical results shows higher concentration of total dissolved
solids (16.67%), electrical conductivity (25%) and magnesium
(8.33%) for pre monsoon and total dissolved solids (16.67%),
electrical conductivity (33.3%) and magnesium (8.33%) for post
monsoon which indicates signs of deterioration as per WHO and BIS
standards. On the other hand, 50% groundwater sample is unsuitable
for irrigation purposes based on irrigation quality parameters. The
study revealed that application of fertilizer for agricultural
contributing the higher concentration of ions in aquifer of Vadodara
district.
Abstract: This paper presents a numerical study on surface heat
transfer characteristics of laminar air flows in parallel-plate dimpled
channels. The two-dimensional numerical model is provided by
commercial code FLUENT and the results are obtained for channels
with symmetrically opposing hemi-cylindrical cavities onto both
walls for Reynolds number ranging from 1000 to 2500. The influence
of variations in relative depth of dimples (the ratio of cavity depth to
the cavity curvature diameter), the number of them and the thermophysical
properties of channel walls on heat transfer enhancement is
studied. The results are evident for existence of an optimum value for
the relative depth of dimples in which the largest wall heat flux and
average Nusselt number can be achieved. In addition, the results of
conjugation simulation indicate that the overall influence of the ratio
of wall thermal conductivity to the one of the fluid on heat transfer
rate is not much significant and can be ignored.
Abstract: This article presents a numerical study of the doublediffusive
mixed convection in a vertical channel filled with porous
medium by using non-equilibrium model. The flow is assumed
fully developed, uni-directional and steady state. The controlling
parameters are thermal Rayleigh number (RaT ), Darcy number (Da),
Forchheimer number (F), buoyancy ratio (N), inter phase heat transfer
coefficient (H), and porosity scaled thermal conductivity ratio
(γ). The Brinkman-extended non-Darcy model is considered. The
governing equations are solved by spectral collocation method. The
main emphasize is given on flow profiles as well as heat and solute
transfer rates, when two diffusive components in terms of buoyancy
ratio are in favor (against) of each other and solid matrix and fluid
are thermally non-equilibrium. The results show that, for aiding flow
(RaT = 1000), the heat transfer rate of fluid (Nuf ) increases upto a
certain value of H, beyond that decreases smoothly and converges
to a constant, whereas in case of opposing flow (RaT = -1000),
the result is same for N = 0 and 1. The variation of Nuf in (N,
Nuf )-plane shows sinusoidal pattern for RaT = -1000. For both cases
(aiding and opposing) the flow destabilize on increasing N by inviting
point of inflection or flow separation on the velocity profile. Overall,
the buoyancy force have significant impact on the non-Darcy mixed
convection under LTNE conditions.
Abstract: Vermicomposting is the conversion of organic waste
into bio-fertilizers through the action of earthworm. This technology
is widely used for organic solid waste management. Waste corn pulp
blended with cow dung manure was vermicomposted over 30 days
using Eisenia fetida earthworms species. pH, temperature, moisture
content, and electrical conductivity were daily monitored. The
feedstock, vermicompost and vermiwash were analyzed for nutrient
composition. The average temperature and moisture content in the
vermi-reactor was 22.5°C and 42.5% respectively. The vermicompost
and vermiwash had an almost neutral pH whilst the electrical
conductivity was 21% higher in the vermicompost. The nitrogen and
potassium content was 57% and 79.6% richer in the vermicompost
respectively compared to the vermiwash. However, the vermiwash
was 84% richer in phosphorous as compared to vermicompost.
Furthermore, the vermiwash was 89.1% and 97.6% richer in Ca and
Mg respectively and was 97.8% richer in Na salts compared to the
vermicompost. The vermiwash also indicated a significantly higher
amount of micronutrients. Both bio-fertilizers were rich in nutrients
specification for fertilizers.
Abstract: Study was conducted to determine the concentration of
copper, cadmium, lead and zinc in Cabomba furcata that found
abundance in Lake Chini. This aquatic plant was collected randomly
within the lake for heavy metal determination. Water quality
measurement was undertaken in situ for temperature, pH,
conductivity and dissolved oksigen using portable multi sensor probe
YSI model 556. The C. furcata was digested using wet digestion
method and heavy metal concentrations were analysed using Atomic
Absorption Spectrometer (AAS) Perkin Elmer 4100B (flame
method). Result of water quality classify Lake Chini between class II
to class III using Malaysian Water Quality Standard. According to
this standard, Lake Chini has moderate quality, which normal for
natural lake. Heavy metal concentrations in C.furcata were low and
found to be lower than the critical toxic value in aquatic plants. Oneway
ANOVA test indicated the heavy metal concentrations in
C.furcata were significantly differ between sampling location. Water
quality and heavy metal concentrations indicates that Lake Chini was
not receives anthropogenic load from nearby activities.
Abstract: Several trillion cigarettes produced worldwide annually lead to many thousands of kilograms of toxic waste. Cigarette butts (CBs) accumulate in the environment due to the poor biodegradability of the cellulose acetate filters. This paper presents some of the results from a continuing study on recycling CBs into fired clay bricks. Physico-mechanical properties of fired clay bricks manufactured with different percentages of CBs are reported and discussed. The results show that the density of fired bricks was reduced by up to 30 %, depending on the percentage of CBs incorporated into the raw materials. Similarly, the compressive strength of bricks tested decreased according to the percentage of CBs included in the mix. The thermal conductivity performance of bricks was improved by 51 and 58 % for 5 and 10 % CBs content respectively. Leaching tests were carried out to investigate the levels of possible leachates of heavy metals from the manufactured clay-CB bricks. The results revealed trace amounts of heavy metals.