Abstract: Large full frequency band gaps of surface and bulk
acoustic waves in two-dimensional phononic band structures with
hollow cylinders are addressed in this paper. It is well-known that
absolute frequency band gaps are difficultly obtained in a band
structure consisted of low-acoustic-impedance cylinders in
high-acoustic-impedance host materials such as PMMA/Ni band
structures. Phononic band structures with hollow cylinders are
analyzed and discussed to obtain large full frequency band gaps not
only for bulk modes but also for surface modes. The tendency of
absolute frequency band gaps of surface and bulk acoustic waves is
also addressed by changing the inner radius of hollow cylinders in this
paper. The technique and this kind of band structure are useful for
tuning the frequency band gaps and the design of acoustic waveguides.
Abstract: UK breweries generate extensive by products in the
form of spent grain, slurry and yeast. Much of the spent grain is
produced by large breweries and processed in bulk for animal feed.
Spent brewery grains contain up to 20% protein dry weight and up to
60% fiber and are useful additions to animal feed. Bulk processing is
economic and allows spent grain to be sold so providing an income
to the brewery. A proportion of spent grain, however, is produced by
small local breweries and is more variably distributed to farms or
other users using intermittent collection methods. Such use is much
less economic and may incur losses if not carefully assessed for
transport costs. This study reports an economic returns of using wet
brewery spent grain (WBSG) in animal feed using the Co-product
Optimizer Decision Evaluator model (Cattle CODE) developed by
the University of Nebraska to predict performance and economic
returns when byproducts are fed to finishing cattle. The results
indicated that distance from brewery to farm had a significantly
greater effect on the economics of use of small brewery spent grain
and that alternative uses than cattle feed may be important to
develop.
Abstract: fibers of pure cellulose can be made from some bacteria such as acetobacter xylinum. Bacterial cellulose fibers are very pure, tens of nm across and about 0.5 micron long. The fibers are very stiff and, although nobody seems to have measured the strength of individual fibers. Their stiffness up to 70 GPa. Fundamental strengths should be at least greater than those of the best commercial polymers, but best bulk strength seems to about the same as that of steel. They can potentially be produced in industrial quantities at greatly lowered cost and water content, and with triple the yield, by a new process. This article presents a critical review of the available information on the bacterial cellulose as a biological nonwoven fabric with special emphasis on its fermentative production and applications. Characteristics of bacterial cellulose biofabric with respect to its structure and physicochemical properties are discussed. Current and potential applications of bacterial cellulose in textile, nonwoven cloth, paper, films synthetic fiber coating, food, pharmaceutical and other industries are also presented.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: Li1.5Al0.5Ti1.5 (PO4)3(LATP) has received much
attention as a solid electrolyte for lithium batteries. In this study, the
LATP solid electrolyte is prepared by the co-precipitation method
using Li3PO4 as a Li source. The LATP is successfully prepared and
the Li ion conductivities of bulk (inner crystal) and total (inner crystal
and grain boundary) are 1.1 × 10-3 and 1.1 × 10-4 S cm-1, respectively.
These values are comparable to the reported values, in which Li2C2O4
is used as the Li source. It is conclude that the LATP solid electrolyte
can be prepared by the co-precipitation method using Li3PO4 as the Li
source and this procedure has an advantage in mass production over
previous procedure using Li2C2O4 because Li3PO4 is lower price
reagent compared with Li2C2O4.
Abstract: Ambient hydrolysis products in moist air and
hydrolysis kinetics in argon with humidity of RH1.5% for
polycrystalline LiH powders and sintered bulks were investigated by
X-ray diffraction, Raman spectroscopy and gravimetry. The results
showed that the hydrolysis products made up a layered structure of
LiOH•H2O/LiOH/Li2O from surface of the sample to inside. In low
humid argon atmosphere, the primary hydrolysis product was Li2O
rather than LiOH. The hydrolysis kinetic curves of LiH bulks present a
paralinear shape, which could be explained by the “Layer Diffusion
Control" model. While a three-stage hydrolysis kinetic profile was
observed for LiH powders under the same experimental conditions.
The first two sections were similar to that of the bulk samples, and the
third section also presents a linear reaction kinetics but with a smaller
reaction rate compared to the second section because of a larger
exothermic effect for the hydrolysis reaction of LiH powder.
Abstract: Hydrate phase equilibria for the binary CO2+water and
CH4+water mixtures in silica gel pore of nominal diameters 6, 30, and
100 nm were measured and compared with the calculated results based
on van der Waals and Platteeuw model. At a specific temperature,
three-phase hydrate-water-vapor (HLV) equilibrium curves for pore
hydrates were shifted to the higher-pressure condition depending on
pore sizes when compared with those of bulk hydrates. Notably,
hydrate phase equilibria for the case of 100 nominal nm pore size were
nearly identical with those of bulk hydrates. The activities of water in
porous silica gels were modified to account for capillary effect, and
the calculation results were generally in good agreement with the
experimental data. The structural characteristics of gas hydrates in
silica gel pores were investigated through NMR spectroscopy.
Abstract: e-mail has become an important means of electronic
communication but the viability of its usage is marred by Unsolicited
Bulk e-mail (UBE) messages. UBE consists of many types
like pornographic, virus infected and 'cry-for-help' messages as well
as fake and fraudulent offers for jobs, winnings and medicines. UBE
poses technical and socio-economic challenges to usage of e-mails.
To meet this challenge and combat this menace, we need to
understand UBE. Towards this end, the current paper presents a
content-based textual analysis of more than 2700 body enhancement
medicinal UBE. Technically, this is an application of Text Parsing
and Tokenization for an un-structured textual document and we
approach it using Bag Of Words (BOW) and Vector Space Document
Model techniques. We have attempted to identify the most
frequently occurring lexis in the UBE documents that advertise
various products for body enhancement. The analysis of such top
100 lexis is also presented. We exhibit the relationship between
occurrence of a word from the identified lexis-set in the given UBE
and the probability that the given UBE will be the one advertising for
fake medicinal product. To the best of our knowledge and survey of
related literature, this is the first formal attempt for identification of
most frequently occurring lexis in such UBE by its textual analysis.
Finally, this is a sincere attempt to bring about alertness against and
mitigate the threat of such luring but fake UBE.
Abstract: Method of determining of moisture diffusivity on two types of autoclaved aerated concretes with different bulk density is represented in the paper. On the specimens were measured one dimensional water transport only on liquid phase. Ever evaluation was done from moisture profiles measured in specific times by capacitance moisture meter. All values from capacitance meter were recalculated to moisture content by mass. Moisture diffusivity was determined in dependence on both moisture and temperature. The experiment temperatures were set at values 55, 65, 75 and 85°C.
Abstract: In this work, simulation algorithms for contact drying
of agitated particulate materials under vacuum and at atmospheric
pressure were developed. The implementation of algorithms gives a
predictive estimation of drying rate curves and bulk bed temperature
during contact drying. The calculations are based on the penetration
model to describe the drying process, where all process parameters
such as heat and mass transfer coefficients, effective bed properties,
gas and liquid phase properties are estimated with proper
correlations. Simulation results were compared with experimental
data from the literature. In both cases, simulation results were in good
agreement with experimental data. Few deviations were identified
and the limitations of the predictive capabilities of the models are
discussed. The programs give a good insight of the drying behaviour
of the analysed powders.
Abstract: In this study, Li4SiO4 powder was successfully
synthesized via sol gel method followed by drying at 150oC. Lithium
oxide, Li2O and silicon oxide, SiO2 were used as the starting
materials with citric acid as the chelating agent. The obtained powder
was then sintered at various temperatures. Crystallographic phase
analysis, morphology and ionic conductivity were investigated
systematically employing X-ray diffraction, Fourier Transform
Infrared, Scanning Electron Microscopy and AC impedance
spectroscopy. XRD result showed the formation of pure monoclinic
Li4SiO4 crystal structure with lattice parameters a = 5.140 Å, b =
6.094 Å, c = 5.293 Å, β = 90o in the sample sintered at 750oC. This
observation was confirmed by FTIR analysis. The bulk conductivity
of this sample at room temperature was 3.35 × 10-6 S cm-1 and the
highest bulk conductivity of 1.16 × 10-4 S cm-1 was obtained at
100°C. The results indicated that, the Li4SiO4 compound has
potential to be used as host for LISICON structured solid electrolyte
for low temperature application.
Abstract: In this paper we present discretization and decomposition methods for a multi-component transport model of a chemical vapor deposition (CVD) process. CVD processes are used to manufacture deposition layers or bulk materials. In our transport model we simulate the deposition of thin layers. The microscopic model is based on the heavy particles, which are derived by approximately solving a linearized multicomponent Boltzmann equation. For the drift-process of the particles we propose diffusionreaction equations as well as for the effects of heat conduction. We concentrate on solving the diffusion-reaction equation with analytical and numerical methods. For the chemical processes, modelled with reaction equations, we propose decomposition methods and decouple the multi-component models to simpler systems of differential equations. In the numerical experiments we present the computational results of our proposed models.
Abstract: In this study, some physical and mechanical properties
of jujube fruits, were measured and compared at constant moisture
content of 15.5% w.b. The results showed that the mean length, width
and thickness of jujube fruits were 18.88, 16.79 and 15.9 mm,
respectively. The mean projected areas of jujube perpendicular to
length, width, and thickness were 147.01, 224.08 and 274.60 mm2,
respectively. The mean mass and volume were 1.51 g and 2672.80
mm3, respectively. The arithmetic mean diameter, geometric mean
diameter and equivalent diameter varied from 14.53 to 20 mm, 14.5
to 19.94 mm, and 14.52 to 19.97 mm, respectively. The sphericity,
aspect ratio and surface area of jujube fruits were 0.91, 0.89 and
926.28 mm2, respectively. Whole fruit density, bulk density and
porosity of jujube fruits were measured and found to be 1.52 g/cm3,
0.3 g/cm3 and 79.3%, respectively. The angle of repose of jujube fruit
was 14.66° (±0.58°). The static coefficient of friction on galvanized
iron steel was higher than that on plywood and lower than that on
glass surface. The values of rupture force, deformation, hardness and
energy absorbed were found to be between 11.13-19.91N, 2.53-
4.82mm, 3.06-5.81N mm and 20.13-39.08 N/mm, respectively.
Abstract: In competitive electricity markets all over the world, an adoption of suitable transmission pricing model is a problem as transmission segment still operates as a monopoly. Transmission pricing is an important tool to promote investment for various transmission services in order to provide economic, secure and reliable electricity to bulk and retail customers. The nodal pricing based on SRMC (Short Run Marginal Cost) is found extremely useful by researchers for sending correct economic signals. The marginal prices must be determined as a part of solution to optimization problem i.e. to maximize the social welfare. The need to maximize the social welfare subject to number of system operational constraints is a major challenge from computation and societal point of views. The purpose of this paper is to present a nodal transmission pricing model based on SRMC by developing new mathematical expressions of real and reactive power marginal prices using GA-Fuzzy based optimal power flow framework. The impacts of selecting different social welfare functions on power marginal prices are analyzed and verified with results reported in literature. Network revenues for two different power systems are determined using expressions derived for real and reactive power marginal prices in this paper.
Abstract: The dissolution of spherical particles in liquids is analyzed dynamically. Here, we consider the case the dissolution of solute yields a solute-free solid phase in the outer portion of a particle. As dissolution proceeds, the interface between the undissolved solid phase and the solute-free solid phase moves towards the center of the particle. We assume that there exist two resistances for the diffusion of solute molecules: the resistance due to the solute-free portion of the particle and that due to a surface layer near solid-liquid interface. In general, the equation governing the dynamic behavior of dissolution needs to be solved numerically. However, analytical expressions for the temporal variation of the size of the undissoved portion of a particle and the variation of dissolution time can be obtained in some special cases. The present analysis takes the effect of variable bulk solute concentration on dissolution into account.
Abstract: The aerodynamic performances of vertical axis wind
turbines are highly affected by tip vortexes. In the present
work, different tip devices are considered and simulated against
a baseline rotor configuration, with the aim of identifying the
best tip architecture. Three different configurations are tested:
winglets, an elliptic termination and an aerodynamic bulkhead.
A comparative analysis on the most promising architectures is
conducted, focusing also on blade torque evolution during a full
revolution of the rotor blade. The most promising technology is
concluded to be a well designed winglet.
Abstract: This paper discusses a genetic algorithm (GA) based optimal load shedding that can apply for electrical distribution networks with and without dispersed generators (DG). Also, the proposed method has the ability for considering constant and variable capacity deficiency caused by unscheduled outages in the bulked generation and transmission system of bulked power supply. The genetic algorithm (GA) is employed to search for the optimal load shedding strategy in distribution networks considering DGs in two cases of constant and variable modelling of bulked power supply of distribution networks. Electrical power distribution systems have a radial network and unidirectional power flows. With the advent of dispersed generations, the electrical distribution system has a locally looped network and bidirectional power flows. Therefore, installed DG in the electrical distribution systems can cause operational problems and impact on existing operational schemes. Introduction of DGs in electrical distribution systems has introduced many new issues in operational and planning level. Load shedding as one of operational issue has no exempt. The objective is to minimize the sum of curtailed load and also system losses within the frame-work of system operational and security constraints. The proposed method is tested on a radial distribution system with 33 load points for more practical applications.
Abstract: Snoring is prevalent and is the most significant feature
of sleep-disordered breathing (SDB). Ignore the therapies of SDB will
lead to serious problems in health. Based on the research of
mechanisms, diagnosis, and treatments of snoring, oral appliances are
ensured in therapeutic effect and compliance, especially the
mandibular advancement devices (MADs). Market survey includes
commercial product reviews and patent analyses. Due to pay more
attention to the sleep medicine, the oral appliances are considered as a
standard treatment of snoring that promoted by American Academy of
Sleep Medicine (AASM). There are more and more adjustable MADs
developed since 1995. According to the patent analyses, there are
many drawbacks existed in the present design, such as uncomfortable,
high cost, bulky volume, and complex adjustment. In this study,
several new designs of the MAD are proposed.
Abstract: with increasing circuits- complexity and demand to
use portable devices, power consumption is one of the most
important parameters these days. Full adders are the basic block of
many circuits. Therefore reducing power consumption in full adders
is very important in low power circuits. One of the most powerconsuming
modules in full adders is XOR/XNOR circuit. This paper
presents two new full adders based on two new logic approaches. The
proposed logic approaches use one XOR or XNOR gate to implement
a full adder cell. Therefore, delay and power will be decreased. Using
two new approaches and two XOR and XNOR gates, two new full
adders have been implemented in this paper. Simulations are carried
out by HSPICE in 0.18μm bulk technology with 1.8V supply voltage.
The results show that the ten-transistors proposed full adder has 12%
less power consumption and is 5% faster in comparison to MB12T
full adder. 9T is more efficient in area and is 24% better than similar
10T full adder in term of power consumption. The main drawback of
the proposed circuits is output threshold loss problem.
Abstract: This study numerically investigates the effects of Electrohydrodynamic on flow patterns and heat transfer enhancement within a cavity which is on the lower wall of channel. In this simulation, effects of using ground wire and ground plate on the flow patterns are compared. Moreover, the positions of electrode wire respecting with ground are tested in the range of angles θ = 0 - 180o. High electrical voltage exposes to air is 20 kV. Bulk mean velocity and temperature of inlet air are controlled at 0.1 m/s and 60 OC, respectively. The result shows when electric field is applied, swirling flow is appeared in the channel. In addition, swirling flow patterns in the main flow of using ground plate are widely spreader than that of using ground wire. Moreover, direction of swirling flow also affects the flow pattern and heat transfer in a cavity. These cause the using ground wire to give the maximum temperature and heat transfer higher than using ground plate. Furthermore, when the angle is at θ = 60o, high shear flow effect is obtained. This results show high strength of swirling flow and effective heat transfer enhancement.