Abstract: The Hall Coefficient (HC) and the Magnetoresistance (MR) have been studied in two-dimensional systems. The HC and the MR in Rectangular Quantum Wire (RQW) subjected to a crossed DC electric field and magnetic field in the presence of a Strong Electromagnetic Wave (EMW) characterized by electric field are studied in this work. Using the quantum kinetic equation for electrons interacting with optical phonons, we obtain the analytic expressions for the HC and the MR with a dependence on magnetic field, EMW frequency, temperatures of systems and the length characteristic parameters of RQW. These expressions are different from those obtained for bulk semiconductors and cylindrical quantum wires. The analytical results are applied to GaAs/GaAs/Al. For this material, MR depends on the ratio of the EMW frequency to the cyclotron frequency. Indeed, MR reaches a minimum at the ratio 5/4, and when this ratio increases, it tends towards a saturation value. The HC can take negative or positive values. Each curve has one maximum and one minimum. When magnetic field increases, the HC is negative, achieves a minimum value and then increases suddenly to a maximum with a positive value. This phenomenon differs from the one observed in cylindrical quantum wire, which does not have maximum and minimum values.
Abstract: Brushless DC motors (BLDC) are widely used in
industrial areas. The BLDC motors are driven either by indirect ACAC
converters or by direct AC-AC converters. Direct AC-AC
converters i.e. matrix converters are used in this paper to drive the
three phase BLDC motor and it eliminates the bulky DC link energy
storage element. A matrix converter converts the AC power supply to
an AC voltage of variable amplitude and variable frequency. A
control technique is designed to generate the switching pulses for the
three phase matrix converter. For the control of speed of the BLDC
motor a separate PI controller and Fuzzy Logic Controller (FLC) are
designed and a hysteresis current controller is also designed for the
control of motor torque. The control schemes are designed and tested
separately. The simulation results of both the schemes are compared
and contrasted in this paper. The results show that the fuzzy logic
control scheme outperforms the PI control scheme in terms of
dynamic performance of the BLDC motor. Simulation results are
validated with the experimental results.
Abstract: The research on thermoelectric has been a blooming field of research for the latest decade, owing to large amount of heat source available to be harvested, being eco-friendly and static in operation. This paper provides the performance of thermoelectric generator (TEG) with bulk material of bismuth telluride, Bi2Te3. Later, the performance of the TEGs is evaluated by considering attaching the TEGs on a plastic (polyethylene sheet) in contrast to the common method of attaching the TEGs on the metal surface.
Abstract: Si-Ge solid solutions (bulk poly- and mono-crystalline
samples, thin films) are characterized by high perspectives for
application in semiconductor devices, in particular, optoelectronics
and microelectronics. From this point of view, complex studying of
structural state of the defects and structural-sensitive physical
properties of Si-Ge solid solutions depending on the contents of Si
and Ge components is very important. Present work deals with the
investigations of microstructure, microhardness, internal friction and
shear modulus of Si1-xGex(x≤0,02) bulk monocrystals conducted at
room temperature. Si-Ge bulk crystals were obtained by Czochralski
method in [111] crystallographic direction. Investigated
monocrystalline Si-Ge samples are characterized by p-type
conductivity and carriers’ concentration 5.1014-1.1015cm-3.
Microhardness was studied on Dynamic Ultra Micro hardness Tester
DUH-201S with Berkovich indenter. Investigate samples are characterized with 0,5x0,5x(10-15)mm3
sizes, oriented along [111] direction at torsion oscillations ≈1Hz,
multistage changing of internal friction and shear modulus has been
revealed in an interval of strain amplitude of 10-5-5.10-3. Critical
values of strain amplitude have been determined at which hysteretic
changes of inelastic characteristics and microplasticity are observed. The critical strain amplitude and elasticity limit values are also
determined. Dynamic mechanical characteristics decreasing trend is
shown with increasing Ge content in Si-Ge solid solutions. Observed
changes are discussed from the point of view of interaction of various
dislocations with point defects and their complexes in a real structure
of Si-Ge solid solutions.
Abstract: Chitosan polyacrylic acid composite membranes were
prepared by a bulk polymerization method in presence of N, N'-
methylene bisacrylamide (crosslinker) and ammonium persulphate as
initiator. Membranes prepared from this copolymer in presence and
absence of Ag nanoparticles were characterized by measuring
mechanical and physical properties, water up-take and antibacterial
properties. The results obtained indicated that the prepared
membranes have antibacterial properties which increase with adding
Ag nanoparticles.
Abstract: These days, the industrial trend is moving away from heavy and bulky passive components to power converter systems that use more and more semiconductor elements. Also, it is difficult to connect the traditional converters to the high and medium voltage. For these reasons, a new family of multilevel inverters has appeared as a solution for working with higher voltage levels. Different modulation topologies like Sinusoidal Pulse Width Modulation (SPWM), Selective Harmonic Elimination Pulse Width Modulation (SHE-PWM) are available for multilevel inverters. In this work, different hybrid modulation techniques which are combination of fundamental frequency modulation and multilevel sinusoidal-modulation are compared. The main characteristic of these modulations are reduction of switching losses with good harmonic performance and balanced power loss dissipation among the device. The proposed hybrid modulation schemes are developed and simulated in Matlab/Simulink for cascaded H-bridge inverter. The results validate the applicability of the proposed schemes for cascaded multilevel inverter.
Abstract: The composite flour blend consisting of corn, pearl
millet, black gram and wheat bran in the ratio of 80:5:10:5 was taken
to prepare the extruded product and their effect on physical properties
of extrudate was studied. The extrusion process was conducted in
laboratory by using twin screw extruder. The physical characteristics
evaluated include lateral expansion, bulk density, water absorption
index, water solubility index, and rehydration ratio and moisture
retention. The Central Composite Rotatable Design (CCRD) was
used to decide the level of processing variables i.e. feed moisture
content (%), screw speed (rpm), and barrel temperature (oC) for the
experiment. The data obtained after extrusion process were analyzed
by using response surface methodology. A second order polynomial
model for the dependent variables was established to fit the
experimental data. The numerical optimization studies resulted in
127°C of barrel temperature, 246 rpm of screw speed, and 14.5% of
feed moisture as optimum variables to produce acceptable extruded
product. The responses predicted by the software for the optimum
process condition resulted in lateral expansion 126%, bulk density
0.28 g/cm3, water absorption index 4.10 g/g, water solubility index
39.90%, rehydration ratio 544% and moisture retention 11.90% with
75% desirability.
Abstract: Mustard leaves are rich in folates, vitamin A, K and
B-complex. Mustard greens are low in calories and fats and rich in
dietary fiber. They are rich in potassium, manganese, iron, copper,
calcium, magnesium and low in sodium. It is very rich in antioxidants
and Phytonutrients. For the optimization of process variables
(moisture content and mustard leave powder), the experiments were
conducted according to central composite Face Centered Composite
design of RSM. The mustard leaves powder was replaced with
composite flour (a combination of rice, chickpea and corn in the ratio
of 70:15:15). The extrudate was extruded in a twin screw extruder at
a barrel temperature of 120°C. The independent variables were
mustard leaves powder (2-10 %) and moisture content (12-20 %).
Responses analyzed were bulk density, water solubility index, water
absorption index, lateral expansion, antioxidant activity, total
phenolic content, and overall acceptability. The optimum conditions
obtained were 7.19 g mustard leaves powder in 100g premix having
16.8% moisture content (w.b).
Abstract: In this paper, we investigated the athermal pressure
behavior of the structural and elastic properties of scheelite BaWO4
phase up to 7 GPa using the ab initio pseudo-potential method. The
calculated lattice parameters pressure relation have been compared
with the experimental values and found to be in good agreement with
these results. Moreover, we present for the first time the investigation
of the elastic properties of this compound using the density functional
perturbation theory (DFPT). It is shown that this phase is
mechanically stable up to 7 GPa after analyzing the calculated elastic
constants. Other relevant quantities such as bulk modulus, pressure
derivative of bulk modulus, shear modulus; Young’s modulus,
Poisson’s ratio, anisotropy factors, Debye temperature and sound
velocity have been calculated. The obtained results, which are
reported for the first time to the best of the author’s knowledge, can
facilitate assessment of possible applications of the title material.
Abstract: We report herein the development and preliminary mechanical characterization of fully-dense multi-wall carbon nanotube (MWCNT)-reinforced ceramics and glasses based on a completely new methodology termed High Shear Compaction (HSC). The tubes are introduced and bound to the matrix grains by aid of polymeric binders to form flexible green bodies which are sintered and densified by spark plasma sintering to unprecedentedly high densities of 100% of the pure-matrix value. The strategy was validated across a PyrexTM glass / MWCNT composite while no identifiable factors limit application to other types of matrices. Nondestructive evaluation, based on ultrasonics, of the dynamic mechanical properties of the materials including elastic, shear and bulk modulus as well as Poisson’s ratio showed optimum property improvement at 0.5 %wt tube loading while evidence of nanoscalespecific energy dissipative characteristics acting complementary to nanotube bridging and pull-out indicate a high potential in a wide range of reinforcing and multifunctional applications.
Abstract: This research paper presents highly optimized barrel
shifter at 22nm Hi K metal gate strained Si technology node. This
barrel shifter is having a unique combination of static and dynamic
body bias which gives lowest power delay product. This power delay
product is compared with the same circuit at same technology node
with static forward biasing at ‘supply/2’ and also with normal reverse
substrate biasing and still found to be the lowest. The power delay
product of this barrel sifter is .39362X10-17J and is lowered by
approximately 78% to reference proposed barrel shifter at 32nm bulk
CMOS technology. Power delay product of barrel shifter at 22nm Hi
K Metal gate technology with normal reverse substrate bias is
2.97186933X10-17J and can be compared with this design’s PDP of
.39362X10-17J. This design uses both static and dynamic substrate
biasing and also has approximately 96% lower power delay product
compared to only forward body biased at half of supply voltage. The
NMOS model used are predictive technology models of Arizona state
university and the simulations to be carried out using HSPICE
simulator.
Abstract: One of the main challenges in using the Discrete
Element Method (DEM) is to specify the correct input parameter
values. In general, the models are sensitive to the input parameter
values and accurate results can only be achieved if the correct values
are specified. For the linear contact model, micro-parameters such as
the particle density, stiffness, coefficient of friction, as well as the
particle size and shape distributions are required. There is a need for
a procedure to accurately calibrate these parameters before any
attempt can be made to accurately model a complete bulk materials
handling system. Since DEM is often used to model applications in
the mining and quarrying industries, a calibration procedure was
developed for materials that consist of relatively large (up to 40 mm
in size) particles. A coarse crushed aggregate was used as the test
material. Using a specially designed large shear box with a diameter
of 590 mm, the confined Young’s modulus (bulk stiffness) and
internal friction angle of the material were measured by means of the
confined compression test and the direct shear test respectively. DEM
models of the experimental setup were developed and the input
parameter values were varied iteratively until a close correlation
between the experimental and numerical results was achieved. The
calibration process was validated by modelling the pull-out of an
anchor from a bed of material. The model results compared well with
experimental measurement.
Abstract: The exponential growth of social media arouses much
attention on public opinion information. The online forums, blogs,
micro blogs are proving to be extremely valuable resources and are
having bulk volume of information. However, most of the social
media data is unstructured and semi structured form. So that it is
more difficult to decipher automatically. Therefore, it is very much
essential to understand and analyze those data for making a right
decision. The online forums hotspot detection is a promising research
field in the web mining and it guides to motivate the user to take right
decision in right time. The proposed system consist of a novel
approach to detect a hotspot forum for any given time period. It uses
aging theory to find the hot terms and E-K-means for detecting the
hotspot forum. Experimental results demonstrate that the proposed
approach outperforms k-means for detecting the hotspot forums with
the improved accuracy.
Abstract: Microalgae Meyerella planktonica is a potential
biofuel source because it can grow in bulk in either autotrophic or
heterotrophic condition. However, the quantitative growth of this
algal type is still low as it tends to precipitates on the bottom.
Besides, the lipid concentration is still low when grown in
autotrophic condition. In contrast, heterotrophic condition can
enhance the lipid concentration. The combination of autotrophic
condition and agitation treatment was conducted to increase the
density of the culture. On the other hand, a heterotrophic condition
was set up to raise the lipid production. A two-stage experiment
was applied to increase the density at the first step and to increase
the lipid concentration in the next step. The autotrophic condition
resulted higher density but lower lipid concentration compared to
heterotrophic one. The agitation treatment produced higher density
in both autotrophic and heterotrophic conditions. The two-stage
experiment managed to enhance the density during the autotrophic
stage and the lipid concentration during the heterotrophic stage.
The highest yield was performed by using 0.4% v/v glycerol as a
carbon source (2.9±0.016 x 10^6 cells w/w) attained 7 days after the
heterotrophic stage began. The lipid concentration was stable
starting from day 7.
Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. This paper describes experimental
investigation on the response of new advanced materials to low and
high velocity load. Blast wave energy absorbers were designed using
two types of porous lightweight raw particle materials based on
expanded glass and ceramics with dimensions of 0.5-1 mm,
combined with polymeric binder. The effect of binder amount on the
static and dynamic properties of designed materials was observed.
Prism shaped specimens were prepared and loaded to obtain physicomechanical
parameters – bulk density, compressive and flexural
strength under quasistatic load, the dynamic response was determined
using Split Hopkinson Pressure bar apparatus. Numerical
investigation of the material behaviour in sandwich structure was
performed using implicit/explicit solver LS-Dyna. As the last step,
the developed material was used as the interlayer of blast resistant
litter bin, and it´s functionality was verified by real field blast tests.
Abstract: Thin-walled elements with a matrix set on a base of
high-valuable Portland cement with dispersed reinforcement from
alkali-resistant glass fibres are used in a range of applications as
claddings of buildings and infrastructure constructions as well as
various architectural elements of residential buildings.
Even though their elementary thickness and therefore total weight
is quite low, architects and building companies demand on even
further decreasing of the bulk density of these fibre-cement elements
for the reason of loading elimination of connected superstructures
and easier assembling in demand conditions.
By the means of various kinds of light-weight aggregates it is
possible to achieve light-weighing of these composite elements.
From the range of possible fillers with different material properties
granulated expanded glass worked the best.
By the means of laboratory testing an effect of two fillers based on
expanded glass on the fibre reinforced cement composite was
verified.
Practical applicability was tested in the production of commonly
manufactured glass fibre reinforced concrete elements, such as
channels for electrical cable deposition, products for urban equipment
and especially various cladding elements.
Even though these are not structural elements, it is necessary to
evaluate also strength characteristics and resistance to environment
for their durability in certain applications.
Abstract: In recent years, the hair building fiber has become
popular, in other words, it is an effective method which helps people
who suffer hair loss or sparse hair since the hair building fiber is
capable to create a natural look of simulated hair rapidly. In the
markets, there are a lot of hair fiber brands that have been designed to
formulate an intense bond with hair strands and make the hair appear
more voluminous instantly. However, those products have their own
set of properties. Thus, in this report, some measurement techniques
are proposed to identify those products. Up to five different brands of
hair fiber are tested. The electrostatic and dielectric properties of the
hair fibers are macroscopically tested using design DC and high
frequency microwave techniques. Besides, the hair fibers are
microscopically analysis by magnifying the structures of the fiber
using scanning electron microscope (SEM). From the SEM photos,
the comparison of the uniformly shaped and broken rate of the hair
fibers in the different bulk samples can be observed respectively.
Abstract: The objective of this study was to identify the optimal
level of partial replacement of Portland cement by the ashes
originating from burning straw and bagasse from sugar cane (ASB).
Order to this end, were made five series of flat plates and cylindrical
bodies: control and others with the partial replacement in 20, 30, 40
and 50% of ASB in relation to the mass of the Ordinary Portland
cement, and conducted a mechanical testing of simple axial
compression (cylindrical bodies) and the four-point bending (flat
plates) and determined water absorption (WA), bulk density (BD)
and apparent void volume (AVV) on both types of specimens. Based
on the data obtained, it may be noted that the control treatment
containing only Portland cement, obtained the best results. However,
the cylindrical bodies with 20% ashes showed better results
compared to the other treatments. And in the formulations plates, the
treatment which showed the best results was 30% cement
replacement by ashes.
Abstract: In this paper, we have compared and analyzed the
electroabsorption properties between with and without excitonic
effect bulk in high purity GaAs spatial light modulator for optical
fiber communication network. The eletroabsorption properties such
as absorption spectra, change in absorption spectra, change in
refractive index and extinction ration has been calculated. We have
also compared the result of absorption spectra and change in
absorption spectra with the experimental results and found close
agreement with experimental results.
Abstract: Physical properties of uranium dinitride (UN2) were
investigated in detail using first principle calculations based on
density functional theory (DFT). To study the strong correlation
effects due to 5f uranium valence electrons, the on-site coulomb
interaction correction U via the Hubbard-like term (DFT+U) was
employed. The UN2 structural, mechanical and thermodynamic
properties were calculated within DFT and Various U of DFT+U
approach.
The Perdew–Burke–Ernzerhof (PBE.5.2) version of the
generalized gradient approximation (GGA) is used to describe the
exchange-correlation with the projector-augmented wave (PAW)
pseudo potentials.
A comparative study shows that results are improved by using the
Hubbard formalism for a certain U value correction like the structural
parameter. For some physical properties the variation versus
Hubbard-U is strong like Young modulus but for others it is weakly
noticeable such as bulk modulus.
We noticed also that from U=7.5 eV, elastic results don’t agree
with the cubic cell because of the C44 values which turn out to be
negative.