Abstract: The experience of engineers and architects practicing today is typically limited to current building code requirements and modern construction methods and materials. However, many cities have a mix of new and old buildings with many buildings constructed over one hundred years ago when building codes and construction methods were much different. When a brick building sustains damage, a structural engineer is often hired to determine the cause of damage as well as determine the necessary repairs. Forensic studies of dozens of brick buildings shows an appreciation of historical building methods and materials is needed to correctly identify the cause of damage and design an appropriate repair. Damage on an older, brick building can be mistakenly attributed to storms or seismic events when the real source of the damage is deficient original construction. Assessing and remediating damaged brickwork on older brick buildings requires an understanding of the original construction, an understanding of older repair methods, and, an understanding of current building code requirements.
Abstract: The main objective of this experimental study is to assess the shear strength and the crack behavior of the triplets built of perforated brickwork masonry elements. In order to observe the influence of shear resistance and energy dissipating before and after retrofitting applications by using the reinforcing system, static-cyclic shear tests were employed in the structural mechanics laboratory of Sakarya University. The reinforcing system is composed of hybrid multiaxial seismic fabric consisting of alkali resistant glass and polypropylene fibers. The plaster as bonding material used in the specimen’s retrofitting consists of expanded glass granular. In order to acquire exact measuring data about the failure behavior of the two mortar joints under shear stressing, vertical load-controlled cylinder having force capacity of 50 kN and loading rate of 1.5 mm/min. with an internal inductive displacement transducers is carried out perpendicular to the triplet specimens. In this study, a total of six triplet specimens with textile reinforcement were prepared for these shear bond tests. The three of them were produced as single-sided reinforced triplets with seismic fabric, while the others were strengthened on both sides. In addition, three triplet specimens without retrofitting and plaster were also tested as reference samples. The obtained test results were given in the manner of force-displacement relationships, ductility coefficients and shear strength parameters comparatively. It is concluded that two-side seismic textile applications on masonry elements with relevant plaster have considerably increased the sheer force resistance and the ductility capacity.
Abstract: This is report on experiment out to compare the sulphate resistance of sand mortar made with five different pozzolanic cement. The pozzolanic cement were prepared by blending powered burnt bricks from the Adamawa, Makurdi, Kano, Kaduna and Niger bricks factories with ordinary Portland cement in the ratio 1:4. Sand –pozzolanic cement mortars of mix ratio 1:6 and 1:3 with water-cement ratio of 0.65 and 0.40 respectively were used to prepare cubes and bars specimens. 150 mortar cubes of size 70mm x 70mm x 70mm and 35 mortar bars of 15mm x 15mm x 100mm dimensions were cast and cured for 28 days. The cured specimens then immersed in the solutions of K2SO4, (NH4)2SO4 and water for 28 days and then tested. The compressive strengths of cubes in water increased by 34% while those in the sulphate solutions decreased. Strength decreases of the cubes, cracking and warping of bars immersed in K2SO4 were less than those in (NH4)2SO4. Specimens made with Niger and Makurdi pulverized burnt bricks experienced less effect of the sulphates and can therefore be used as pozzolan in mortar and concrete to resist sulphate.
Abstract: There need to construct building walls with lightweight masonry bricks/blocks and mortar to reduce the weight and cost of cooling/heating of buildings in hot/cold climates is growing partly due to legislations on energy use and global warming. In this paper, the development of Palm Kernel Shell masonry mortar (PKSMM) prepared with Portland cement and crushed PKS fine aggregate (an agricultural waste) is demonstrated. We show that PKSMM can be used as a lightweight mortar for the construction of lightweight masonry walls with good thermal insulation efficiency than the natural river sand commonly used for masonry mortar production.
Abstract: This paper summarizes the results of a survey on
smart non-structural element dynamic dissipation when installed
in modern high-rise mega-frame prototypes. An innovative glazed
curtain wall was designed using Shape Memory Alloy (SMA)
joints in order to increase the energy dissipation and enhance
the seismic/wind response of the structures. The studied buildings
consisted of thirty- and sixty-storey planar frames, extracted from
reference three-dimensional steel Moment Resisting Frame (MRF)
with outriggers and belt trusses. The internal core was composed of
a CBF system, whilst outriggers were placed every fifteen stories
to limit second order effects and inter-storey drifts. These structural
systems were designed in accordance with European rules and
numerical FE models were developed with an open-source code,
able to account for geometric and material nonlinearities. With
regard to the characterization of non-structural building components,
full-scale crescendo tests were performed on aluminium/glass curtain
wall units at the laboratory of the Construction Technologies
Institute (ITC) of the Italian National Research Council (CNR),
deriving force-displacement curves. Three-dimensional brick-based
inelastic FE models were calibrated according to experimental results,
simulating the fac¸ade response. Since recent seismic events and
extreme dynamic wind loads have generated the large occurrence of
non-structural components failure, which causes sensitive economic
losses and represents a hazard for pedestrians safety, a more
dissipative glazed curtain wall was studied. Taking advantage of the
mechanical properties of SMA, advanced smart joints were designed
with the aim to enhance both the dynamic performance of the single
non-structural unit and the global behavior. Thus, three-dimensional
brick-based plastic FE models were produced, based on the innovated
non-structural system, simulating the evolution of mechanical
degradation in aluminium-to-glass and SMA-to-glass connections
when high deformations occurred. Consequently, equivalent nonlinear
links were calibrated to reproduce the behavior of both tested and
smart designed units, and implemented on the thirty- and sixty-storey
structural planar frame FE models. Nonlinear time history analyses
(NLTHAs) were performed to quantify the potential of the new
system, when considered in the lateral resisting frame system (LRFS)
of modern high-rise MRFs. Sensitivity to the structure height was
explored comparing the responses of the two prototypes. Trends
in global and local performance were discussed to show that, if
accurately designed, advanced materials in non-structural elements provide new sources of energy dissipation.
Abstract: In recent years, nanotechnology has played an important role in the design of an efficient radiation shielding polymeric composites. It is well known that, high loading of nanomaterials with radiation absorption properties can enhance the radiation attenuation efficiency of shielding structures. However, due to difficulties in dispersion of nanomaterials into polymer matrices, there has been a limitation in higher loading percentages of nanoparticles in the polymer matrix. Therefore, the objective of the present work is to provide a methodology to fabricate and then to characterize the functionally graded radiation shielding structures, which can provide an efficient radiation absorption property along with good structural integrity. Sandwich structures composed of Ultra High Molecular Weight Polyethylene (UHMWPE) fabric as face sheets and functionally graded epoxy nanocomposite as core material were fabricated. A method to fabricate a functionally graded core panel with controllable gradient dispersion of nanoparticles is discussed. In order to optimize the design of functionally graded sandwich composites and to analyze the stress distribution throughout the sandwich composite thickness, a finite element method was used. The sandwich panels were discretized using 3-Dimensional 8 nodded brick elements. Classical laminate analysis in conjunction with simplified micromechanics equations were used to obtain the properties of the face sheets. The presented finite element model would provide insight into deformation and damage mechanics of the functionally graded sandwich composites from the structural point of view.
Abstract: The economy of Botswana has increased extensively since its independence. In contrast to this increase, the construction industry which is one of the key indicators of a developing nation continues to be highly dependent on imported building material products from the neighbouring countries of South Africa, Namibia, Zimbabwe, and Zambia. Only two companies in the country currently blend cement. Even then, the overwhelming majority of raw materials used in the blends are imported. Furthermore, there are no glass manufacturers in Botswana. The ceramic industry is limited to the manufacture of clay bricks notwithstanding a few studios on crockery and sanitary ware which nonetheless use imported clay. This paper presents natural resources and industrial waste products in Botswana that can be used for the development of sustainable building materials. It also investigates at the distribution and cost of other widely used building materials in the country. Finally, the present paper looks at projects and national strategies aimed at a country-wide development of a sustainable building materials industry together with their successes and hitches.
Abstract: In this paper, a procedure for the evaluation of seismic behavior of slender masonry structures (towers, bell towers, chimneys, minarets, etc.) is presented. The presented procedure is based on a full three-dimensional modal analyses and frequency measurements. As well-known, masonry is a composite material formed by bricks, or stone blocks, and mortar arranged more or less regularly and adopted for many centuries as structural material. Dynamic actions may represent the major risk of collapse of brickworks, and despite the progress achieved so far in science and mechanics; the assessment of their seismic performance remains a challenging task. Then, reliable physical and numerical models are worthy of recommendation. In this paper, attention is paid to the historical bell tower of the Basilica of Santa Maria Gloriosa dei Frari - usually called Frari - one of the greatest churches in Venice, Italy.
Abstract: As a developing country, Bangladesh has to face numerous challenges. Self Independence in electricity, contributing to climate change by reducing carbon emission and bringing the backward population of society to the mainstream is more challenging for them. Therefore, it is essential to ensure recycled use of local products to the maximum level in every sector. Some private organizations have already worked alongside government to bring the backward population to the mainstream by developing their financial capacities. As rice husk is the largest single category of the total energy supply in Bangladesh. As part of this strategy, rice husk can play a great as a promising renewable energy source, which is readily available, has considerable environmental benefits and can produce electricity and ensure multiple uses of byproducts in construction technology. For the first time in Bangladesh, an experimental multidimensional project depending on Rice Husk Electricity and Rice Husk Ash (RHA) concrete brick/block under Green Eco-Tech Limited has already been started. Project analysis, opportunity, sustainability, the high monitoring component, limitations and finally evaluated data reflecting the viability of establishing more projects using rice husk are discussed in this paper. The by-product of rice husk from the production of green electricity, RHA, can be used for making, in particular, RHA concrete brick/block in Bangladeshi aspects is also discussed here.
Abstract: This study presents a simple inverse heat transfer procedure for predicting the wall erosion and the time-varying thickness of the protective bank that covers the inside surface of the refractory brick wall of a melting furnace. The direct problem is solved by using the Finite-Volume model. The melting/solidification process is modeled using the enthalpy method. The inverse procedure rests on the Levenberg-Marquardt method combined with the Broyden method. The effect of the location of the temperature sensors and of the measurement noise on the inverse predictions is investigated. Recommendations are made concerning the location of the temperature sensor.
Abstract: This study presents an inverse analysis for predicting the thermal conductivities and the heat flux of a high-temperature metallurgical reactor simultaneously. Once these thermal parameters are predicted, the time-varying thickness of the protective phase-change bank that covers the inside surface of the brick walls of a metallurgical reactor can be calculated. The enthalpy method is used to solve the melting/solidification process of the protective bank. The inverse model rests on the Levenberg-Marquardt Method (LMM) combined with the Broyden method (BM). A statistical analysis for the thermal parameter estimation is carried out. The effect of the position of the temperature sensors, total number of measurements and measurement noise on the accuracy of inverse predictions is investigated. Recommendations are made concerning the location of temperature sensors.
Abstract: Environmental performance of artisanal brick manufacture was studied by Lifecycle Assessment (LCA) methodology and Computational Fluid Dynamics (CFD) analysis in Mexico. The main objective of this paper is to evaluate the environmental impact during artisanal brick manufacture. LCA cradle-to-gate approach was complemented with CFD analysis to carry out an Environmental Impact Assessment (EIA). The lifecycle includes the stages of extraction, baking and transportation to the gate. The functional unit of this study was the production of a single brick in Chihuahua, Mexico and the impact categories studied were carcinogens, respiratory organics and inorganics, climate change radiation, ozone layer depletion, ecotoxicity, acidification/ eutrophication, land use, mineral use and fossil fuels. Laboratory techniques for fuel characterization, gas measurements in situ, and AP42 emission factors were employed in order to calculate gas emissions for inventory data. The results revealed that the categories with greater impacts are ecotoxicity and carcinogens. The CFD analysis is helpful in predicting the thermal diffusion and contaminants from a defined source. LCA-CFD synergy complemented the EIA and allowed us to identify the problem of thermal efficiency within the system.
Abstract: This paper reports an experimental work that aimed to investigate the effects of clay brick waste, as part of fine aggregate, on rendering mortar performance. The brick, in crushed form, was from a local brick manufacturer that was rejected due to being of-standard. It was used to replace 33.33 %, 50 %, 66.66 % and 100 % by weight of the quarry sand in mortar. Effects of the brick replacement on the mortar key properties intended for wall plastering were investigated; these are workability, compressive strength, flexural strength, linear shrinkage, water absorption by total immersion and by capillary suction. The results showed that as the brick replacement level increased, the mortar workability reduced. The linear shrinkage increases over time and decreases with the introduction of brick waste. The compressive and flexural strengths decrease with the increase of brick waste because of their great water absorption.
Abstract: Coal fly ash, an industrial by product of coal
combustion thermal power plants is considered as a hazardous
material and its improper disposal has become an environmental
issue. On the other hand, manufacturing conventional clay bricks
involves on consumption of large amount of clay and leads
substantial depletion of topsoil. This paper unveils the possibility of
using fly ash as a partial replacement of clay for brick manufacturing
considering the local technology practiced in Bangladesh. The effect
of fly ash with different replacing ratio (0%, 20%, 30%, 40%, and
50% by volume) of clay on properties of bricks was studied. Bricks
were made in the field parallel to ordinary bricks marked with
specific number for different percentage to identify them at time of
testing. No physical distortion is observed in fly ash brick after
burning in the kiln. Results from laboratory test show that
compressive strength of brick is decreased with the increase of fly
ash and maximum compressive strength is found to be 19.6 MPa at
20% of fly ash. In addition, water absorption of fly ash brick is
increased with the increase of fly ash. The abrasion value and
Specific gravity of coarse aggregate prepared from brick with fly ash
also studied and the results of this study suggests that 20% fly ash
can be considered as the optimum fly ash content for producing good
quality bricks utilizing present practiced technology.
Abstract: The ventilated façade has great advantages when
compared to traditional façades as it reduces the air conditioning
thermal loads due to the stack effect induced by solar radiation in the
air chamber. Optimizing energy consumption by using a ventilated
façade can be used not only in newly built buildings but also it can be
implemented in existing buildings, opening the field of
implementation to energy building retrofitting works. In this sense, the following three prototypes of façade where
designed, built and further analyzed in this research: non-ventilated
façade (NVF); slightly ventilated façade (SLVF) and strongly
ventilated façade (STVF). The construction characteristics of the
three facades are based on the Spanish regulation of building
construction “Technical Building Code”. The façades have been
monitored by type-k thermocouples in a representative day of the
summer season in Madrid (Spain). Moreover, an analysis of variance
(ANOVA) with repeated measures, studying the thermal lag in the
ventilated and no-ventilated façades has been designed. Results show that STVF façade presents higher levels of thermal
inertia as the thermal lag reduces up to 17% (daily mean) compared
to the non-ventilated façade. In addition, the statistical analysis
proves that an increase of the ventilation holes size in STVF façades
can improve the thermal lag significantly (p >0.05) when compared
to the SLVF façade.
Abstract: In this study, the feasibility of incorporating ceramic
waste from bricks (perforated brick and double hollow brick) and
extruded polystyrene (XPS) waste, is analysed.
Results show that it is possible to incorporate up to 25% of
ceramic waste and 4% of XPS waste over the weight of gypsum in a
gypsum matrix. Furthermore, with the addition of ceramic waste an
8% of surface hardness increase and a 25% of capillary water
absorption reduction can be obtained. On the other hand, with the
addition of XPS, a 26% reduction of density and a 37% improvement
of thermal conductivity can be obtained.
The obtained results are favorable to use these materials in order to
produce prefabricated gypsum and also as material for interior
cladding walls.
Abstract: This study investigates the suitability of using plastic,
such as polyethylene terephthalate (PET), as a partial replacement of
natural coarse and fine aggregates (for example, brick chips and
natural sand) to produce lightweight concrete for load bearing
structural members. The plastic coarse aggregate (PCA) and plastic
fine aggregate (PFA) were produced from melted polyethylene
terephthalate (PET) bottles. Tests were conducted using three
different water–cement (w/c) ratios, such as 0.42, 0.48, and 0.57,
where PCA and PFA were used as 50% replacement of coarse and
fine aggregate respectively. Fresh and hardened properties of
concrete have been compared for natural aggregate concrete (NAC),
PCA concrete (PCC) and PFA concrete (PFC). The compressive
strength of concrete at 28 days varied with the water–cement ratio for
both the PCC and PFC. Between PCC and PFC, PFA concrete
showed the highest compressive strength (23.7 MPa) at 0.42 w/c ratio
and also the lowest compressive strength (13.7 MPa) at 0.57 w/c
ratio. Significant reduction in concrete density was mostly observed
for PCC samples, ranging between 1977–1924 kg/m³. With the
increase in water–cement ratio PCC achieved higher workability
compare to both NAC and PFC. It was found that both the PCA and
PFA contained concrete achieved the required compressive strength
to be used for structural purpose as partial replacement of the natural
aggregate; but to obtain the desired lower density as lightweight
concrete the PCA is most suited.
Abstract: Experimental production methods of Chevreul’s salt
being an intermediate stage product in copper recovery were
investigated on this article. Chevreul’s salt, Cu2SO3.CuSO3.2H2O,
being a mixed valence copper sulphite compound, has been obtained
by using different methods and reagents. Chevreul’s salt has an
intense brick-red color. It is highly stable and expensive. The
production of Chevreul’s salt plays a key role in hydrometallurgy.
Thermodynamic tendency on precipitation of Chevreul’s salt is
related to pH and temperature. Besides, SO2 gaseous is a versatile
reagent for precipitating of copper sulphites, Using of SO2 for
selective precipitation can be made by appropriate adjustments of pH
and temperature. Chevreul’s salt does not form in acidic solutions if
those solutions contains considerable amount of sulfurous acid. It is
necessary to maintain between pH 2–4.5, because, solubility of
Chevreul’s salt increases with decreasing of pH values. Also, the
region which Chevreul’s salt is stable can be seen from the potentialpH
diagram.
Abstract: Asphaltic concrete for pavement construction in India
are produced by using crushed stone, gravels etc. as aggregate. In
north-Eastern region of India, there is a scarcity of stone aggregate.
Therefore the road engineers are always in search of an optional
material as aggregate which can replace the regularly used material.
The purpose of this work was to evaluate the utilization of
substandard or marginal aggregates in flexible pavement
construction. The investigation was undertaken to evaluate the effects
of using lower quality aggregates such as over burnt brick aggregate
on the preparation of asphalt concrete for flexible pavements. The
scope of this work included a review of available literature and
existing data, a laboratory evaluation organized to determine the
effects of marginal aggregates and potential techniques to upgrade
these substandard materials, and a laboratory evaluation of these
upgraded marginal aggregate asphalt mixtures. Over burnt brick
aggregates are water susceptible and can leads to moisture damage.
Moisture damage is the progressive loss of functionality of the
material owing to loss of the adhesion bond between the asphalt
binder and the aggregate surface. Hence zycosoil as an anti striping
additive were evaluated in this study. This study summarizes the
results of the laboratory evaluation carried out to investigate the
properties of asphalt concrete prepared with zycosoil modified over
burnt brick aggregate. Marshall specimen were prepared with stone
aggregate, zycosoil modified stone aggregate, over burnt brick
aggregate and zycosoil modified over burnt brick aggregate. Results
show that addition of zycosoil with stone aggregate increased
stability by 6% and addition of zycosoil with over burnt brick
aggregate increased stability by 30%.
Abstract: This entry concerned with dense silica bricks
microstructure was produced as a part of a project within the
Technology Agency of the Czech Republic which is being
implemented in cooperation of the biggest producer of refractories
the P-D Refractories CZ company with the research organisation
Brno University of Technology. The paper is focused on the
influence of mixture homogenisation and the influence of grain size
of the mineraliser on the resulting utility properties of the material as
well as its microstructure. It has a decisive influence on the durability
of the material in a building structure. This paper is a continuation of
a previously published study dealing with the suitability of various
types of mineralising agents in terms of density, strength and mineral
composition of silica brick.
The entry describes the influence of the method of mixture
homogenisation and the influence of granulometry of the applied Femineralising
agent on the resulting silica microstructure. Porosity,
density, phase composition and microstructure of the experimentally
prepared silica bricks samples were examined and the results were
discussed in context with the technology of homogenisation and
firing temperature used. The properties of silica bricks samples were
compared to the sample without any Fe-mineraliser.