Abstract: This study investigated the influence of Cloisite-15A nanoclay on the physical, performance, and mechanical properties of bitumen binder. Cloisite-15A was blended in the bitumen in variegated percentages from 1% to 9% with increment of 2%. The blended bitumen was characterized using penetration, softening point, and dynamic viscosity using rotational viscometer, and compared with unmodified bitumen equally penetration grade 60/70. The rheological parameters were investigated using Dynamic Shear Rheometer (DSR), and mechanical properties were investigated by using Marshall Stability test. The results indicated an increase in softening point, dynamic viscosity and decrease in binder penetration. Rheological properties of bitumen increase complex modulus, decrease phase angle and improve rutting resistances as well. There was significant improvement in Marshall Stability, rather marginal improvement in flow value. The best improvement in the modified binder was obtained with 5% Cloisite-15A nanoclay.
Abstract: Bitumen has been widely used as the binder of aggregate in road pavement due to its good viscoelastic properties, as a viscous organic mixture with various chemical compositions. Bitumen is a liquid at high temperature and it becomes brittle at low temperatures, and this temperature-sensitivity can cause the rutting and cracking of the pavement and limit its application. Therefore, the properties of existing asphalt materials need to be enhanced. The pavement with polymer modified bitumen exhibits greater resistance to rutting and thermal cracking, decreased fatigue damage, as well as stripping and temperature susceptibility; however, they are expensive and their applications have disadvantages. Bituminous mixtures are composed of very irregular aggregates bound together with hydrocarbon-based asphalt, with a low volume fraction of voids dispersed within the matrix. Montmorillonite (MMT) is a layered silicate with low cost and abundance, which consists of layers of tetrahedral silicate and octahedral hydroxide sheets. Recently, the layered silicates have been widely used for the modification of polymers, as well as in many different fields. However, there are not too much studies related with the preparation of the modified asphalt with MMT, currently. In this study, organo-clay-modified bitumen, and calcareous aggregate and organo-clay blends were prepared by hot blending method with OMMT, which has been synthesized using a cationic surfactant (Cetyltrymethylammonium bromide, CTAB) and long chain hydrocarbon, and MMT. When the exchangeable cations in the interlayer region of pristine MMT were exchanged with hydrocarbon attached surfactant ions, the MMT becomes organophilic and more compatible with bitumen. The effects of the super hydrophobic OMMT onto the micro structural and mechanic properties (Marshall Stability and volumetric parameters) of the prepared blends were investigated. Stability and volumetric parameters of the blends prepared were measured using Marshall Test. Also, in order to investigate the morphological and micro structural properties of the organo-clay-modified bitumen and calcareous aggregate and organo-clay blends, their SEM and HRTEM images were taken. It was observed that the stability and volumetric parameters of the prepared mixtures improved significantly compared to the conventional hot mixes and even the stone matrix mixture. A micro structural analysis based on SEM images indicates that the organo-clay platelets dispersed in the bitumen have a dominant role in the increase of effectiveness of bitumen - aggregate interactions.
Abstract: With the strengthened regulation on the mandatory use
of recycled aggregate, development of construction materials using
recycled aggregate has recently increased. This study aimed to secure
the performance of asphalt concrete mixture by developing
recycled-modified asphalt using recycled basalt aggregate from the
Jeju area. The strength of the basalt aggregate from the Jeju area used
in this study was similar to that of general aggregate, while the specific
surface area was larger due to the development of pores. Modified
asphalt was developed using a general aggregate-recycled aggregate
ratio of 7:3, and the results indicated that the Marshall stability
increased by 27% compared to that of asphalt concrete mixture using
only general aggregate, and the flow values showed similar levels.
Also, the indirect tensile strength increased by 79%, and the toughness
increased by more than 100%. In addition, the TSR for examining
moisture resistance was 0.95 indicating that the reduction in the
indirect tensile strength due to moisture was very low (5% level), and
the developed recycled-modified asphalt could satisfy all the quality
standards of asphalt concrete mixture.
Abstract: Asphalt concrete pavements have a short life cycle,
failing mainly due to temperature changes, traffic loading and ageing.
Modified asphalt mixtures provide the technology to produce a
bituminous binder with improved viscoelastic properties, which
remain in balance over a wider temperature range and loading
conditions. In this research, 60/70 penetration grade asphalt binder
was modified by adding 2, 4, 6, 8 and 10 percent by weight of asphalt
binder following the wet process and the mineral aggregate was
modified by adding 1, 2, 3, 4 and 5 percent crumb rubber by volume
of the mineral aggregate following the dry process. The LDPE
modified asphalt binder rheological properties were evaluated. The
laboratory results showed an increase in viscosity, softening point
and stiffness of the binder. The modified asphalt was then used in
preparing asphalt mixtures by Marshall Mix design procedure. The
Marshall Stability values for mixes containing 2% crumb rubber and
4% LDPE were found to be 30% higher than the conventional asphalt
concrete mix.
Abstract: Asphaltic concrete for pavement construction in India
are produced by using crushed stone, gravels etc. as aggregate. In
north-Eastern region of India, there is a scarcity of stone aggregate.
Therefore the road engineers are always in search of an optional
material as aggregate which can replace the regularly used material.
The purpose of this work was to evaluate the utilization of
substandard or marginal aggregates in flexible pavement
construction. The investigation was undertaken to evaluate the effects
of using lower quality aggregates such as over burnt brick aggregate
on the preparation of asphalt concrete for flexible pavements. The
scope of this work included a review of available literature and
existing data, a laboratory evaluation organized to determine the
effects of marginal aggregates and potential techniques to upgrade
these substandard materials, and a laboratory evaluation of these
upgraded marginal aggregate asphalt mixtures. Over burnt brick
aggregates are water susceptible and can leads to moisture damage.
Moisture damage is the progressive loss of functionality of the
material owing to loss of the adhesion bond between the asphalt
binder and the aggregate surface. Hence zycosoil as an anti striping
additive were evaluated in this study. This study summarizes the
results of the laboratory evaluation carried out to investigate the
properties of asphalt concrete prepared with zycosoil modified over
burnt brick aggregate. Marshall specimen were prepared with stone
aggregate, zycosoil modified stone aggregate, over burnt brick
aggregate and zycosoil modified over burnt brick aggregate. Results
show that addition of zycosoil with stone aggregate increased
stability by 6% and addition of zycosoil with over burnt brick
aggregate increased stability by 30%.
Abstract: Utilization of waste material in asphalt pavement
would be beneficial in order to find an alternative solution to increase
service life of asphalt pavement and reduce environmental pollution
as well. One of these waste materials is Polyethylene Terephthalate
(PET) which is a type of polyester material and is produced in a large
extent. This research program is investigating the effects of adding
waste PET particles into the asphalt mixture with a maximum size of
2.36 mm. Different percentages of PET were added into the mixture
during dry process. Gap-graded mixture (SMA 14) and PG 80-100
asphalt binder have been used for this study. To evaluate PET
reinforced asphalt mixture different laboratory investigations have
been conducted on specimens. Marshall Stability test was carried
out. Besides, stiffness modulus test and indirect tensile fatigue test
were conducted on specimens at optimum asphalt content. It was
observed that in many cases PET reinforced SMA mixture had better
mechanical properties in comparison with control mixture.
Abstract: This paper presents a research conducted to investigate the effect of mixing process on polypropylene (PP) modified bitumen mixed with well graded aggregate to form modified bituminous concrete mix. Two mode of mixing, namely dry and wet with different concentration of polymer polypropylene was used with 80/100 pen bitumen, to evaluate the bituminous concrete mix properties. Three percentages of polymer varying from 1-3% by the weight of bitumen was used in this study. Three mixes namely control mix, wet mix and dry mix were prepared. Optimum binder content was calculated considering Marshall Stability, flow, air voids and Marshall Quotient at different bitumen content varying from 4% - 6.5% for control, dry and wet mix. Engineering properties thus obtained at the calculated optimum bitumen content revealed that wet mixing process is advantageous in comparison to dry mixing as it increases the stiffness of the mixture with the increase in polymer content in bitumen. Stiffness value for wet mix increases with the increase in polymer content which is beneficial in terms of rutting. 1% PP dry mix also shows enhanced stiffness, with the air void content limited to 4%.The flow behaviour of dry mix doesn't indicate any major difference with the increase in polymer content revealing that polymer acting as an aggregate only without affecting the viscosity of the binder in the mix. Polypropylene (PP) when interacted with 80 pen base bitumen enhances its performance characteristics which were brought about by altered rheological properties of the modified bitumen. The decrease in flow with the increase in binder content reflects the increase in viscosity of binder which induces the plastic flow in the mix. Workability index indicates that wet mix were easy to compact up to desired void ratio in comparison to dry mix samples.
Abstract: The present study explains the effect of aggregate
gradation on moisture damage in bituminous mixes. Three types of
aggregate gradation and two types of binder; VG-30 and Polymer
modified bitumen (PMB-40) are used. Moisture susceptibility tests
like retained stability and tensile strength ratio (TSR) and static creep
test are conducted on Marshall specimens. The creep test was also
conducted for conditioned and unconditioned specimens to observe
the effect of moisture on creep behaviour. The results indicate that
Marshall stability value is higher in PMB-40 mix than VG-30 mixes.
Moisture susceptibility of PMB-40 mixes is low when compared with
mix using VG-30. The reduction in retained stability, and indirect
tensile strength and increase in creep are evaluated for finer, coarser
and normal gradation of aggregate to observe the effect of gradation
on moisture susceptibility of mixes. The retained stability is least
affected when compared with other moisture susceptibility
parameters