Abstract: Construction delay is unavoidable in developing
countries including Malaysia. It is defined as time overrun or
extension of time for completion of a project. The purpose of the
study is to determine the causes of delay in Malaysian construction
industries based on previous worldwide research. The field survey
conducted includes the experienced developers, consultants and
contractors in Malaysia. 34 causes of the construction delay have
been determined and 24 have been selected using the Rasch model
analysis. The analysis result will be used as the baseline for the next
research to find the causes of delay in the Malaysian construction
industry taking place in Malaysian higher learning institutions.
Abstract: Traditionally, wind tunnel models are made of metal
and are very expensive. In these years, everyone is looking for ways
to do more with less. Under the right test conditions, a rapid
prototype part could be tested in a wind tunnel. Using rapid prototype
manufacturing techniques and materials in this way significantly
reduces time and cost of production of wind tunnel models. This
study was done of fused deposition modeling (FDM) and their ability
to make components for wind tunnel models in a timely and cost
effective manner. This paper discusses the application of wind tunnel
model configuration constructed using FDM for transonic wind
tunnel testing. A study was undertaken comparing a rapid
prototyping model constructed of FDM Technologies using
polycarbonate to that of a standard machined steel model. Testing
covered the Mach range of Mach 0.3 to Mach 0.75 at an angle-ofattack
range of - 2° to +12°. Results from this study show relatively
good agreement between the two models and rapid prototyping
Method reduces time and cost of production of wind tunnel models.
It can be concluded from this study that wind tunnel models
constructed using rapid prototyping method and materials can be
used in wind tunnel testing for initial baseline aerodynamic database
development.
Abstract: The aerodynamic performances of vertical axis wind
turbines are highly affected by tip vortexes. In the present
work, different tip devices are considered and simulated against
a baseline rotor configuration, with the aim of identifying the
best tip architecture. Three different configurations are tested:
winglets, an elliptic termination and an aerodynamic bulkhead.
A comparative analysis on the most promising architectures is
conducted, focusing also on blade torque evolution during a full
revolution of the rotor blade. The most promising technology is
concluded to be a well designed winglet.
Abstract: Efficient preprocessing is very essential for automatic
recognition of handwritten documents. In this paper, techniques on
segmenting words in handwritten Arabic text are presented. Firstly,
connected components (ccs) are extracted, and distances among
different components are analyzed. The statistical distribution of this
distance is then obtained to determine an optimal threshold for words
segmentation. Meanwhile, an improved projection based method is
also employed for baseline detection. The proposed method has been
successfully tested on IFN/ENIT database consisting of 26459
Arabic words handwritten by 411 different writers, and the results
were promising and very encouraging in more accurate detection of
the baseline and segmentation of words for further recognition.
Abstract: The Aggregate Production Plan (APP) is a schedule of
the organization-s overall operations over a planning horizon to
satisfy demand while minimizing costs. It is the baseline for any
further planning and formulating the master production scheduling,
resources, capacity and raw material planning. This paper presents a
methodology to model the Aggregate Production Planning problem,
which is combinatorial in nature, when optimized with Genetic
Algorithms. This is done considering a multitude of constraints of
contradictory nature and the optimization criterion – overall cost,
made up of costs with production, work force, inventory, and
subcontracting. A case study of substantial size, used to develop the
model, is presented, along with the genetic operators.
Abstract: Multimedia information availability has increased
dramatically with the advent of video broadcasting on handheld
devices. But with this availability comes problems of maintaining the
security of information that is displayed in public. ISMA Encryption
and Authentication (ISMACryp) is one of the chosen technologies for
service protection in DVB-H (Digital Video Broadcasting-
Handheld), the TV system for portable handheld devices. The
ISMACryp is encoded with H.264/AVC (advanced video coding),
while leaving all structural data as it is. Two modes of ISMACryp are
available; the CTR mode (Counter type) and CBC mode (Cipher
Block Chaining) mode. Both modes of ISMACryp are based on 128-
bit AES algorithm. AES algorithms are more complex and require
larger time for execution which is not suitable for real time
application like live TV. The proposed system aims to gain a deep
understanding of video data security on multimedia technologies and
to provide security for real time video applications using selective
encryption for H.264/AVC. Five level of security proposed in this
paper based on the content of NAL unit in Baseline Constrain profile
of H.264/AVC. The selective encryption in different levels provides
encryption of intra-prediction mode, residue data, inter-prediction
mode or motion vectors only. Experimental results shown in this
paper described that fifth level which is ISMACryp provide higher
level of security with more encryption time and the one level provide
lower level of security by encrypting only motion vectors with lower
execution time without compromise on compression and quality of
visual content. This encryption scheme with compression process
with low cost, and keeps the file format unchanged with some direct
operations supported. Simulation was being carried out in Matlab.
Abstract: In this paper, an automated algorithm to estimate and remove the continuous baseline from measured spectra containing both continuous and discontinuous bands is proposed. The algorithm uses previous information contained in a Continuous Database Spectra (CDBS) to obtain a linear basis, with minimum number of sampled vectors, capable of representing a continuous baseline. The proposed algorithm was tested by using a CDBS of flame spectra where Principal Components Analysis and Non-negative Matrix Factorization were used to obtain linear bases. Thus, the radical emissions of natural gas, oil and bio-oil flames spectra at different combustion conditions were obtained. In order to validate the performance in the baseline estimation process, the Goodness-of-fit Coefficient and the Root Mean-squared Error quality metrics were evaluated between the estimated and the real spectra in absence of discontinuous emission. The achieved results make the proposed method a key element in the development of automatic monitoring processes strategies involving discontinuous spectral bands.
Abstract: The aim of the work presented here was to either use
existing forest dynamic simulation models or calibrate a new one
both within the SYMFOR framework with the purpose of examining
changes in stand level basal area and functional composition in
response to selective logging considering trees > 10 cm d.b.h for two
areas of undisturbed Amazonian non flooded tropical forest in Brazil
and one in Peru. Model biological realism was evaluated for forest in
the undisturbed and selectively logged state and it was concluded that
forest dynamics were realistically represented. Results of the logging
simulation experiments showed that in relation to undisturbed forest
simulation subject to no form of harvesting intervention there was a
significant amount of change over a 90 year simulation period that
was positively proportional to the intensity of logging. Areas which
had in the dynamic equilibrium of undisturbed forest a greater
proportion of a specific ecological guild of trees known as the light
hardwoods (LHW’s) seemed to respond more favorably in terms of
less deviation but only within a specific range of baseline forest
composition beyond which compositional diversity became more
important. These finds are in line partially with practical management
experience and partiality basic systematics theory respectively.
Abstract: We investigated the response of testosterone (T),
growth hormone (GH), cortisol (C), steroid hormone binding
globulin (SHBG), insulin-like growth factor (IGF-1), insulin-like
growth factor binding protein-3 (IGFBP-3), and some anaboliccatabolic
indexes, i.e.: T/C, T/SHBG, and IGF-1/IGFBP-3 to
maximal exercise in endurance-trained athletes (TREN) and
untrained subjects (CG). The baseline concentration of IGF-1 was
higher in athletes (TREN) when compared to the CG (p
Abstract: The increased use of biodiesel implies variations on both greenhouse gases and air pollutant emissions. Some studies point out that the use of biodiesel blends on diesel can help in controlling air pollution and promote a reduction of CO2 emissions. Reductions on PM, SO2, VOC and CO emissions are also expected, however NOx emissions may increase, which may potentiate O3 formation. This work aims to assess the impact of the biodiesel use on air quality, through a numerical modeling study, taking the Northern region of Portugal as a case study. The emission scenarios are focused on 2008 (baseline year) and 2020 (target year of Renewable Energy Directive-RED) and on three biodiesel blends (B0, B10 and B20). In a general way the use of biodiesel by 2020 will reduce the CO2 and air pollutants emissions in the Northern Portugal, improving air quality. However it will be in a very small extension.
Abstract: Prior to the use of detectors, characteristics
comparison study was performed and baseline established. In patient
specific QA, the portal dosimetry mean values of area gamma,
average gamma and maximum gamma were 1.02, 0.31 and 1.31 with
standard deviation of 0.33, 0.03 and 0.14 for IMRT and the
corresponding values were 1.58, 0.48 and 1.73 with standard
deviation of 0.31, 0.06 and 0.66 for VMAT. With ImatriXX 2-D
array system, on an average 99.35% of the pixels passed the criteria
of 3%-3 mm gamma with standard deviation of 0.24 for dynamic
IMRT. For VMAT, the average value was 98.16% with a standard
deviation of 0.86. The results showed that both the systems can be
used in patient specific QA measurements for IMRT and VMAT.
The values obtained with the portal dosimetry system were found to
be relatively more consistent compared to those obtained with
ImatriXX 2-D array system.
Abstract: Increasing concerns over climate change have limited
the liberal usage of available energy technology options. India faces
a formidable challenge to meet its energy needs and provide adequate
energy of desired quality in various forms to users in sustainable
manner at reasonable costs. In this paper, work carried out with an
objective to study the role of various energy technology options
under different scenarios namely base line scenario, high nuclear
scenario, high renewable scenario, low growth and high growth rate
scenario. The study has been carried out using Model for Energy
Supply Strategy Alternatives and their General Environmental
Impacts (MESSAGE) model which evaluates the alternative energy
supply strategies with user defined constraints on fuel availability,
environmental regulations etc. The projected electricity demand, at
the end of study period i.e. 2035 is 500490 MWYr. The model
predicted the share of the demand by Thermal: 428170 MWYr,
Hydro: 40320 MWYr, Nuclear: 14000 MWYr, Wind: 18000 MWYr
in the base line scenario. Coal remains the dominant fuel for
production of electricity during the study period. However, the
import dependency of coal increased during the study period. In
baseline scenario the cumulative carbon dioxide emissions upto 2035
are about 11,000 million tones of CO2. In the scenario of high nuclear
capacity the carbon dioxide emissions reduced by 10 % when nuclear
energy share increased to 9 % compared to 3 % in baseline scenario.
Similarly aggressive use of renewables reduces 4 % of carbon
dioxide emissions.
Abstract: We investigated the effects of modified
preprogrammed training mode Chase Trainer from Balance Trainer
(BT3, HurLab, Tampere, Finland) on athlete who experienced
unilateral Patellofemoral Pain Syndrome (PFPS). Twenty-seven
athletes with mean age= 14.23 ±1.31 years, height = 164.89 ± 7.85
cm, weight = 56.94 ± 9.28 kg were randomly assigned to two groups:
experiment (EG; n = 14) and injured (IG; n = 13). EG performed a
series of Chase Trainer program which required them to shift their
body weight at different directions, speeds and angle of leaning twice
a week for duration of 8 weeks. The static postural control and
perceived pain level measures were taken at baseline, after 6 weeks
and 8 weeks of training. There was no significant difference in any of
tested variables between EG and IG before and after 6-week the
intervention period. However, after 8-week of training, the postural
control (eyes open) and perceived pain level of EG improved
compared to IG (p
Abstract: In this paper, the noise maps for the area encircled by
the Second Ring Road in Riyadh city are developed based on real
measured data. Sound level meters, GPS receivers to determine
measurement position, a database program to manage the measured
data, and a program to develop the maps are used. A baseline noise
level has been established at each short-term site so subsequent
monitoring may be conducted to describe changes in Riyadh-s noise
environment. Short-term sites are used to show typical daytime and
nighttime noise levels at specific locations by short duration grab
sampling.
Abstract: While the problem based learning (PBL) approach promotes unsupervised self-directed learning (SDL), many students experience difficulty juggling the role of being an information recipient and information seeker. Logbooks have been used to assess trainee doctors but not in other areas. This study aimed to determine the effectiveness of logbook for assessing SDL during PBL sessions in first year medical students. The log book included a learning checklist and knowledge and skills components. Comparisons with the baseline assessment of student performance in PBL and that at semester end after logbook intervention showed significant improvements in student performance (31.5 ± 8 vs. 17.7 ± 4.4; p
Abstract: The Prediction of aerodynamic characteristics and
shape optimization of airfoil under the ground effect have been carried
out by integration of computational fluid dynamics and the multiobjective
Pareto-based genetic algorithm. The main flow
characteristics around an airfoil of WIG craft are lift force, lift-to-drag
ratio and static height stability (H.S). However, they show a strong
trade-off phenomenon so that it is not easy to satisfy the design
requirements simultaneously. This difficulty can be resolved by the
optimal design. The above mentioned three characteristics are chosen
as the objective functions and NACA0015 airfoil is considered as a
baseline model in the present study. The profile of airfoil is
constructed by Bezier curves with fourteen control points and these
control points are adopted as the design variables. For multi-objective
optimization problems, the optimal solutions are not unique but a set
of non-dominated optima and they are called Pareto frontiers or Pareto
sets. As the results of optimization, forty numbers of non- dominated
Pareto optima can be obtained at thirty evolutions.
Abstract: Information is power. Geographical information is an
emerging science that is advancing the development of knowledge to
further help in the understanding of the relationship of “place" with
other disciplines such as crime. The researchers used crime data for
the years 2004 to 2007 from the Baguio City Police Office to
determine the incidence and actual locations of crime hotspots.
Combined qualitative and quantitative research methodology was
employed through extensive fieldwork and observation, geographic
visualization with Geographic Information Systems (GIS) and Global
Positioning Systems (GPS), and data mining. The paper discusses
emerging geographic visualization and data mining tools and
methodologies that can be used to generate baseline data for
environmental initiatives such as urban renewal and rejuvenation.
The study was able to demonstrate that crime hotspots can be
computed and were seen to be occurring to some select places in the
Central Business District (CBD) of Baguio City. It was observed that
some characteristics of the hotspot places- physical design and milieu
may play an important role in creating opportunities for crime. A list
of these environmental attributes was generated. This derived
information may be used to guide the design or redesign of the urban
environment of the City to be able to reduce crime and at the same
time improve it physically.
Abstract: A state of the art Speaker Identification (SI) system requires a robust feature extraction unit followed by a speaker modeling scheme for generalized representation of these features. Over the years, Mel-Frequency Cepstral Coefficients (MFCC) modeled on the human auditory system has been used as a standard acoustic feature set for SI applications. However, due to the structure of its filter bank, it captures vocal tract characteristics more effectively in the lower frequency regions. This paper proposes a new set of features using a complementary filter bank structure which improves distinguishability of speaker specific cues present in the higher frequency zone. Unlike high level features that are difficult to extract, the proposed feature set involves little computational burden during the extraction process. When combined with MFCC via a parallel implementation of speaker models, the proposed feature set outperforms baseline MFCC significantly. This proposition is validated by experiments conducted on two different kinds of public databases namely YOHO (microphone speech) and POLYCOST (telephone speech) with Gaussian Mixture Models (GMM) as a Classifier for various model orders.
Abstract: Concerns about low levels of children-s physical activity and motor skill development, prompted the Ministry of Education to trial a physical activity pilot project (PAPP) in 16 New Zealand primary schools. The project comprised professional development and training in physical education for lead teachers and introduced four physical activity coordinators to liaise with and increase physical activity opportunities in the pilot schools. A survey of generalist teachers (128 baseline, 155 post-intervention) from these schools looked at timetabled physical activity sessions and issues related to teaching physical education. The authors calculated means and standard deviations of data relating to timetabled PE sessions and used a one-way analysis of variance to determine significant differences. Results indicated time devoted to physical activity related subjects significantly increased over the course of the intervention. Teacher-s reported improved confidence and competence, which resulted in an improvement in quality physical education delivered more often.
Abstract: This study focuses on examining why the range of
experience with respect to HIV infection is so diverse, especially in
regard to the latency period. An agent-based approach in modelling
the infection is used to extract high-level behaviour which cannot be
obtained analytically from the set of interaction rules at the cellular
level. A prototype model encompasses local variation in baseline
properties, contributing to the individual disease experience, and is
included in a network which mimics the chain of lymph nodes. The
model also accounts for stochastic events such as viral mutations.
The size and complexity of the model require major computational
effort and parallelisation methods are used.