Abstract: In the present work, a study has been made on the combination of the electrical discharge machining (EDM) with ultrasonic vibrations to improve the machining efficiency. In experiments the graphite used as tool electrode and material of workpiece was AISIH13 tool steel. The parameters such as discharge peak current and pulse duration were changed to explore their effect on the material removal rate (MRR), relative tool wear ratio (TWR) and surface roughness. From the experimental result it can be seen that ultrasonic vibration of the workpiece can significantly reduces the inactive pulses and improves the stability of process. It was found that ultrasonic assisted EDM (US-EDM) is effective in attaining a high material removal rate (MRR) in finishing regime.
Abstract: This paper proposes a novel architecture for At-
Home medical care which enables senior citizens, patients
with chronic ailments and patients requiring post- operative
care to be remotely monitored in the comfort of their homes.
This architecture is implemented using sensors and wireless
networking for transmitting patient data to the hospitals,
health- care centers for monitoring by medical professionals.
Patients are equipped with sensors to measure their
physiological parameters, like blood pressure, pulse rate etc.
and a Wearable Data Acquisition Unit is used to transmit the
patient sensor data. Medical professionals can be alerted to
any abnormal variations in these values for diagnosis and
suitable treatment. Security threats and challenges inherent to
wireless communication and sensor network have been
discussed and a security mechanism to ensure data
confidentiality and source authentication has been proposed.
Symmetric key algorithm AES has been used for encrypting
the data and a patent-free, two-pass block cipher mode CCFB
has been used for implementing semantic security.
Abstract: One of the most important problems to solve is eye
location for a driver fatigue monitoring system. This paper presents an
efficient method to achieve fast and accurate eye location in grey level
images obtained in the real-word driving conditions. The structure of
eye region is used as a robust cue to find possible eye pairs. Candidates
of eye pair at different scales are selected by finding regions which
roughly match with the binary eye pair template. To obtain real one,
all the eye pair candidates are then verified by using support vector
machines. Finally, eyes are precisely located by using binary vertical
projection and eye classifier in eye pair images. The proposed method
is robust to deal with illumination changes, moderate rotations, glasses
wearing and different eye states. Experimental results demonstrate its
effectiveness.
Abstract: This paper presents a experiment to estimate the
influences of cutting conditions in microstructure changes of
machining austenitic 304 stainless steel, especially for wear insert. The
wear insert were prefabricated with a width of 0.5 mm. And the forces,
temperature distribution, RS, and microstructure changes were
measured by force dynamometer, infrared thermal camera, X-ray
diffraction, XRD, SEM, respectively. The results told that the different
combinations of machining condition have a significant influence on
machined surface microstructure changes. In addition to that, the
ANOVA and AOMwere used to tell the different influences of cutting
speed, feed rate, and wear insert.
Abstract: In order to define a new model of Tunisian foot
sizes and for building the most comfortable shoes, Tunisian
industrialists must be able to offer for their customers products able
to put on and adjust the majority of the target population concerned.
Moreover, the use of models of shoes, mainly from others
country, causes a mismatch between the foot and comfort of the
Tunisian shoes.
But every foot is unique; these models become uncomfortable for
the Tunisian foot. We have a set of measures produced from a
3D scan of the feet of a diverse population (women, men ...) and we
try to analyze this data to define a model of foot specific to the
Tunisian footwear design.
In this paper we propose tow new approaches to modeling a new
foot sizes model. We used, indeed, the neural networks, and specially
the Kohonen network.
Next, we combine neural networks with the concept of half-foot
size to improve the models already found. Finally, it was necessary to
compare the results obtained by applying each approach and we
decide what-s the best approach that give us the most model of foot
improving more comfortable shoes.
Abstract: This work presents the results of a study carried out to
determine the sliding wear behavior and its effect on the process
parameters of components manufactured by direct metal laser
sintering (DMLS). A standard procedure and specimen had been used
in the present study to find the wear behavior. Using Taguchi-s
experimental technique, an orthogonal array of modified L8 had been
developed. Sliding wear testing using pin-on-disk machine was
carried out and analysis of variance (ANOVA) technique was used to
investigate the effect of process parameters and to identify the main
process parameter that influences the properties of wear behavior on
the DMLS components. It has been found that part orientation, one
of the selected process parameter had more influence on wear as
compared to other selected process parameters.
Abstract: According to historical legend, after the revelation of the holy Qur'an, which gave the hijab compulsory and women were required to cover the head and body with a handkerchief, and the general form of clothing in her veil, Muslim women have begun to comply with this worthy tradition. This article discusses the history of the rise and spread of the hijab and its types. And here is described in detail types of hijab and its intended value, style hijab in different regions. Now wearing the hijab, hijab in general the problem is important not only in the Arab world, but also in the world.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece using copper tools are being optimized
according to its individual machining characteristic i.e. Electrode
Wear Ratio (EWR). Higher EWR would give bad dimensional
precision for the EDM machined workpiece because of high
electrode wear. Hence, the quality characteristic for EWR is set to
lower-the-better to achieve the optimum dimensional precision for
the machined workpiece. Taguchi method has been used for the
construction, layout and analysis of the experiment for EWR
machining characteristic. The use of Taguchi method in the
experiment saves a lot of time and cost of preparing and machining
the experiment samples. Therefore, an L18 Orthogonal array
which was the fundamental component in the statistical design of
experiments has been used to plan the experiments and Analysis of
Variance (ANOVA) is used to determine the optimum machining
parameters for this machining characteristic. The control
parameters selected for this optimization experiments are polarity,
pulse on duration, discharge current, discharge voltage, machining
depth, machining diameter and dielectric liquid pressure. The
result had shown that negative polarity machining parameter
setting will decreases EWR.
Abstract: In the present work, a comparative study on the
microstructure and mechanical properties of as cast, cast aged and
forged aged A356 alloy has been investigated. The study reveals that
mechanical properties of A356 alloy are highly influenced by melt
treatment and solid state processing. Cast aged alloys achieve highest
strength and hardness compared to as cast and forge aged ones. Ones
treated with combined addition of grain refiners and modifiers
achieve maximum strength and hardness. Cast aged A356 alloy
possesses higher wear resistance compared to as cast and forge aged
ones. Forging improves both strength and ductility of alloys over as
cast ones. However, the improvement in ductility is perceptible only
for properly grain refined and modified alloys. Ones refined with
0.65% Al-3Ti shows highest improvement in ductility while ones
treated with 0.20% Al-10Sr exhibits less improvement in ductility.
Abstract: Recently, the issue of machine condition monitoring
and fault diagnosis as a part of maintenance system became global
due to the potential advantages to be gained from reduced
maintenance costs, improved productivity and increased machine
availability. The aim of this work is to investigate the effectiveness
of a new fault diagnosis method based on power spectral density
(PSD) of vibration signals in combination with decision trees and
fuzzy inference system (FIS). To this end, a series of studies was
conducted on an external gear hydraulic pump. After a test under
normal condition, a number of different machine defect conditions
were introduced for three working levels of pump speed (1000, 1500,
and 2000 rpm), corresponding to (i) Journal-bearing with inner face
wear (BIFW), (ii) Gear with tooth face wear (GTFW), and (iii)
Journal-bearing with inner face wear plus Gear with tooth face wear
(B&GW). The features of PSD values of vibration signal were
extracted using descriptive statistical parameters. J48 algorithm is
used as a feature selection procedure to select pertinent features from
data set. The output of J48 algorithm was employed to produce the
crisp if-then rule and membership function sets. The structure of FIS
classifier was then defined based on the crisp sets. In order to
evaluate the proposed PSD-J48-FIS model, the data sets obtained
from vibration signals of the pump were used. Results showed that
the total classification accuracy for 1000, 1500, and 2000 rpm
conditions were 96.42%, 100%, and 96.42% respectively. The results
indicate that the combined PSD-J48-FIS model has the potential for
fault diagnosis of hydraulic pumps.
Abstract: Tribological behavior and wear regimes of ascast
and heattreted Al-Cu-Mg matrix composites containing SiC
particles were studied using a pin-on-disc wear testing apparatus
against an EN32 steel counterface giving emphasis on wear rate as
a function of applied pressures (0.2, 0.6, 1.0 and 1.4 MPa) at
different sliding distances (1000, 2000, 3000, 4000 and 5000
meters) and at a fixed sliding speed of 3.35m/s. The results showed
that the composite exhibited lower wear rate than that of the matrix
alloy and the wear rate of the composites is noted to be invariant to
the sliding distance and is reducing by heat treatment. Wear
regimes such as low, mild and severe wear were observed as per the
Archard-s wear calculations. It is very interesting to note that the
mild wear is almost constant in all the wear regimes.
Abstract: The field of biomedical materials plays an imperative
requisite and a critical role in manufacturing a variety of biological
artificial replacements in a modern world. Recently, titanium (Ti)
materials are being used as biomaterials because of their superior
corrosion resistance and tremendous specific strength, free- allergic
problems and the greatest biocompatibility compared to other
competing biomaterials such as stainless steel, Co-Cr alloys,
ceramics, polymers, and composite materials. However, regardless of
these excellent performance properties, Implantable Ti materials have
poor shear strength and wear resistance which limited their
applications as biomaterials. Even though the wear properties of Ti
alloys has revealed some improvements, the crucial effectiveness of
biomedical Ti alloys as wear components requires a comprehensive
deep understanding of the wear reasons, mechanisms, and techniques
that can be used to improve wear behavior. This review examines
current information on the effect of thermal and thermomechanical
processing of implantable Ti materials on the long-term prosthetic
requirement which related with wear behavior. This paper focuses
mainly on the evolution, evaluation and development of effective
microstructural features that can improve wear properties of bio
grade Ti materials using thermal and thermomechanical treatments.
Abstract: The aim of the study was to identify seat belt wearing
factor among road users in Malaysia. Evidence-based approach
through in-depth crash investigation was utilised to determine the
intended objectives. The objective was scoped into crashes
investigated by Malaysian Institute of Road Safety Research
(MIROS) involving passenger vehicles within 2007 and 2010. Crash
information of a total of 99 crash cases involving 240 vehicles and
864 occupants were obtained during the study period. Statistical test
and logistic regression analysis have been performed. Results of the
analysis revealed that gender, seat position and age were associated
with seat belt wearing compliance in Malaysia. Males are 97.6%
more likely to wear seat belt compared to females (95% CI 1.317 to
2.964). By seat position, the finding indicates that frontal occupants
were 82 times more likely to be wearing seat belt (95% CI 30.199 to
225.342) as compared to rear occupants. It is also important to note
that the odds of seat belt wearing increased by about 2.64% (95% CI
1.0176 to 1.0353) for every one year increase in age. This study is
essential in understanding the Malaysian tendency in belting up
while being occupied in a vehicle. The factors highlighted in this
study should be emphasized in road safety education in order to
increase seat belt wearing rate in this country and ultimately in
preventing deaths due to road crashes.
Abstract: In this paper, the full state feedback controllers
capable of regulating and tracking the speed trajectory are presented.
A fourth order nonlinear mean value model of a 448 kW turbocharged
diesel engine published earlier is used for the purpose.
For designing controllers, the nonlinear model is linearized and
represented in state-space form. Full state feedback controllers
capable of meeting varying speed demands of drivers are presented.
Main focus here is to investigate sensitivity of the controller to the
perturbations in the parameters of the original nonlinear model.
Suggested controller is shown to be highly insensitive to the
parameter variations. This indicates that the controller is likely
perform with same accuracy even after significant wear and tear of
engine due to its use for years.
Abstract: In turning hardened steel, polycrystalline cubic boron
nitride (cBN) compacts are widely used, due to their higher hardness
and higher thermal conductivity. However, in milling hardened steel,
fracture of cBN cutting tools readily occurs because they have poor
fracture toughness. Therefore, coated cemented carbide tools, which
have good fracture toughness and wear resistance, are generally
widely used. In this study, hardened steel (ASTM D2, JIS SKD11,
60HRC) was milled with three physical vapor deposition
(PVD)-coated cemented carbide end mill cutters in order to determine
effective tool materials for cutting hardened steel at high cutting
speeds. The coating films used were (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating films. (Ti,W,Si,Al)N is a new type of
coating film. The inner layer of the (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating system is (Ti,W)N coating film, and
the outer layer is (Ti,W,Si)N and (Ti,W,Si,Al)N coating films,
respectively. Furthermore, commercial (Ti,Al)N-based coating film
was also used. The following results were obtained: (1) In milling
hardened steel at a cutting speed of 3.33 m/s, the tool wear width of the
(Ti,W)N/(Ti,W,Si,Al)N-coated tool was smaller than that of the
(Ti,W)N/(Ti,W,Si)N-coated tool. And, compared with the commercial
(Ti,Al)N, the tool wear width of the (Ti,W)N/(Ti,W,Si,Al)N-coated
tool was smaller than that of the (Ti,Al)N-coated tool. (2) The tool
wear of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool increased with an
increase in cutting speed. (3) The (Ti,W)N/(Ti,W,Si,Al)N-coated
cemented carbide was an effective tool material for high-speed cutting
below a cutting speed of 3.33 m/s.
Abstract: The stochastic nature of tool life using conventional discrete-wear data from experimental tests usually exists due to many individual and interacting parameters. It is a common practice in batch production to continually use the same tool to machine different parts, using disparate machining parameters. In such an environment, the optimal points at which tools have to be changed, while achieving minimum production cost and maximum production rate within the surface roughness specifications, have not been adequately studied. In the current study, two relevant aspects are investigated using coated and uncoated inserts in turning operations: (i) the accuracy of using machinability information, from fixed parameters testing procedures, when variable parameters situations are emerged, and (ii) the credibility of tool life machinability data from prior discrete testing procedures in a non-stop machining. A novel technique is proposed and verified to normalize the conventional fixed parameters machinability data to suit the cases when parameters have to be changed for the same tool. Also, an experimental investigation has been established to evaluate the error in the tool life assessment when machinability from discrete testing procedures is employed in uninterrupted practical machining.
Abstract: Integration of system process information obtained
through an image processing system with an evolving knowledge
database to improve the accuracy and predictability of wear particle
analysis is the main focus of the paper. The objective is to automate
intelligently the analysis process of wear particle using classification
via self organizing maps. This is achieved using relationship
measurements among corresponding attributes of various
measurements for wear particle. Finally, visualization technique is
proposed that helps the viewer in understanding and utilizing these
relationships that enable accurate diagnostics.
Abstract: Integration of system process information obtained
through an image processing system with an evolving knowledge
database to improve the accuracy and predictability of wear debris
analysis is the main focus of the paper. The objective is to automate
intelligently the analysis process of wear particle using classification
via self-organizing maps. This is achieved using relationship
measurements among corresponding attributes of various
measurements for wear debris. Finally, visualization technique is
proposed that helps the viewer in understanding and utilizing these
relationships that enable accurate diagnostics.
Abstract: The increasing influence of traffic on building
objects and people residing in them should be taken into account in
diagnosis and design. Users of buildings expect that vibrations
occurring in their environment, will not only lead to damage to the
building or its accelerated wear, but neither would affect the required
comfort in rooms designed to accommodate people. This article
describes the methods and principles useful in designing and building
diagnostics located near transportation routes, with particular
emphasis on the impact of traffic vibration on people in buildings. It
also describes the procedures used in obtaining information about the
parameters of vibrations in different cases of diagnostics and design.
A universal algorithm of procedure in diagnostics and design of
buildings taking into account assurance of human vibration comfort
of people residing in the these buildings was presented.