Abstract: In this study, to clarify the effectiveness of an
aluminum/chromium/tungsten-based-coated tool for cutting sintered
steel, tool wear was experimentally investigated. The sintered steel
was turned with the (Al60,Cr25,W15)N-, (Al60,Cr25,W15)(C,N)- and
(Al64,Cr28,W8)(C,N)-coated cemented carbide tools according to the
physical vapor deposition (PVD) method. Moreover, the tool wear of
the aluminum/chromium/tungsten-based-coated item was compared
with that of the (Al,Cr)N coated tool. Furthermore, to clarify the tool
wear mechanism of the aluminum/chromium/tungsten-coating film for
cutting sintered steel, Scanning Electron Microscope observation and
Energy Dispersive x-ray Spectroscopy mapping analysis were
conducted on the abraded surface. The following results were
obtained: (1) The wear progress of the (Al64,Cr28,W8)(C,N)-coated
tool was the slowest among that of the five coated tools. (2) Adding
carbon (C) to the aluminum/chromium/tungsten-based-coating film
was effective for improving the wear-resistance. (3) The main wear
mechanism of the (Al60,Cr25,W15)N-, the (Al60,Cr25,W15)(C,N)-
and the (Al64,Cr28,W8)(C,N)-coating films was abrasive wear.
Abstract: Recently, there have been a lot of earthquakes in Japan.
It is necessary to promote seismic isolation devices for buildings. The
devices have been hardly diffused in attached houses, because the
devices are very expensive. We should develop a low-cost seismic
isolation device for detached houses. We suggested a new seismic
isolation device which uses a two-layer circular tube as a unit. If
hysteresis is produced in the two-layer circular tube under lateral
compression load, we think that the two-layer circular tube can have
energy absorbing capacity. It is necessary to contact the outer layer
and the inner layer to produce hysteresis. We have previously reported
how the inner layer comes in contact with the outer layer from a
perspective of analysis used mechanics of materials. We have clarified
that the inner layer comes in contact with the outer layer under a lateral
compression load. In this paper, we explored contact area between the
outer layer and the inner layer under a lateral compression load by
using FEA. We think that changing the inner layer’s thickness is
effective in increase the contact area. In order to change the inner
layer’s thickness, we changed the shape of the inner layer. As a result,
the contact area changes depending on the inner layer’s thickness.
Additionally, we experimented to check whether hysteresis occurs in
fact. As a consequence, we can reveal hysteresis in the two-layer
circular tube under the condition.
Abstract: In this study, WC-Ni-based cemented carbides having different nickel contents were used as the substrate for cutting tool materials. Hardened steel was turned by a (Ti,W,Si)N-coated WC-Ni-based cemented carbide tool, and the tool wear was experimentally investigated. The following results were obtained: (1) In the (Ti,W,Si)N-coated WC-Ni-based cemented carbide, the hardness of the coating film was not much different from the content of the binding material, Ni, and the adhesion strength increased with a decrease in Ni content. (2) There is little difference between the wear progress of the (Ti,W,Si)N-coated WC-7%Ni-based cemented carbide tool and that of the (Ti,W,Si)N-coated WC-6%Co-based cemented carbide tool. (3) The wear progress of the (Ti,W,Si)N-coated WC-Ni-based cemented carbide became slower with a decrease in Ni content.
From the above, it is has become clear that WC-Ni-based cemented carbide can be used as a substrate for cutting tool materials.
Abstract: In turning hardened steel, polycrystalline cubic boron
nitride (cBN) compacts are widely used, due to their higher hardness
and higher thermal conductivity. However, in milling hardened steel,
fracture of cBN cutting tools readily occurs because they have poor
fracture toughness. Therefore, coated cemented carbide tools, which
have good fracture toughness and wear resistance, are generally
widely used. In this study, hardened steel (ASTM D2, JIS SKD11,
60HRC) was milled with three physical vapor deposition
(PVD)-coated cemented carbide end mill cutters in order to determine
effective tool materials for cutting hardened steel at high cutting
speeds. The coating films used were (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating films. (Ti,W,Si,Al)N is a new type of
coating film. The inner layer of the (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating system is (Ti,W)N coating film, and
the outer layer is (Ti,W,Si)N and (Ti,W,Si,Al)N coating films,
respectively. Furthermore, commercial (Ti,Al)N-based coating film
was also used. The following results were obtained: (1) In milling
hardened steel at a cutting speed of 3.33 m/s, the tool wear width of the
(Ti,W)N/(Ti,W,Si,Al)N-coated tool was smaller than that of the
(Ti,W)N/(Ti,W,Si)N-coated tool. And, compared with the commercial
(Ti,Al)N, the tool wear width of the (Ti,W)N/(Ti,W,Si,Al)N-coated
tool was smaller than that of the (Ti,Al)N-coated tool. (2) The tool
wear of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool increased with an
increase in cutting speed. (3) The (Ti,W)N/(Ti,W,Si,Al)N-coated
cemented carbide was an effective tool material for high-speed cutting
below a cutting speed of 3.33 m/s.