Abstract: Axisymmetric vibration of an infinite Pyrocomposite
circular hollow cylinder made of inner and outer pyroelectric layer of
6mm-class bonded together by a Linear Elastic Material with Voids
(LEMV) layer is studied. The exact frequency equation is obtained
for the traction free surfaces with continuity condition at the
interfaces. Numerical results in the form of data and dispersion
curves for the first and second mode of the axisymmetric vibration of
the cylinder BaTio3 / Adhesive / BaTio3 by taking the Adhesive layer
as an existing Carbon Fibre Reinforced Polymer (CFRP) are
compared with a hypothetical LEMV layer with and without voids
and as well with a pyroelectric hollow cylinder. The damping is
analyzed through the imaginary parts of the complex frequencies.
Abstract: Ambiguities in effects of earthquake on various
structures in all earthquake codes would necessitate more study and
research concerning influential factors on dynamic behavior.
Previous studies which were done on different features in different
buildings play a major role in the type of response a structure makes
to lateral vibrations. Diagnosing each of these irregularities can help
structure designers in choosing appropriate setbacks for decreasing
possible damages. Therefore vertical setback is one of the irregularity
factors in the height of the building where can be seen in skyscrapers
and hotels. Previous researches reveal notable changes in the place of
these setbacks showing dynamic response of the structure.
Consequently analyzing 48 models of concrete frames for 3, 6 and 9
stories heights with three different bays in general shape of a surface
decline by height have been constructed in ETABS2000 software,
and then the shape effect of each and every one of these frames in
period scale has been discussed. The result of this study reveals that
not only mass, stiffness and height but also shape of the frame is
influential.
Abstract: This paper describes a combined mathematicalgraphical
approach for optimum tool path planning in order to
improve machining efficiency. A methodology has been used that
stabilizes machining operations by adjusting material removal rate in
pocket milling operations while keeping cutting forces within limits.
This increases the life of cutting tool and reduces the risk of tool
breakage, machining vibration, and chatter. Case studies reveal the
fact that application of this approach could result in a slight increase
of machining time, however, a considerable reduction of tooling cost,
machining vibration, noise and chatter can be achieved in addition to
producing a better surface finish.
Abstract: The main objective of the present paper is to derive an easy numerical technique for the analysis of the free vibration through the stepped regions of plates. Based on the utilities of the step by step integration initial values IV and Finite differences FD methods, the present improved Initial Value Finite Differences (IVFD) technique is achieved. The first initial conditions are formulated in convenient forms for the step by step integrations while the upper and lower edge conditions are expressed in finite difference modes. Also compatibility conditions are created due to the sudden variation of plate thickness. The present method (IVFD) is applied to solve the fourth order partial differential equation of motion for stepped plate across two different panels under the sudden step compatibility in addition to different types of end conditions. The obtained results are examined and the validity of the present method is proved showing excellent efficiency and rapid convergence.
Abstract: The gel-supported precipitation (GSP) process can be
used to make spherical particles (spherules) of nuclear fuel,
particularly for very high temperature reactors (VHTR) and even for
implementing the process called SPHEREPAC. In these different
cases, the main characteristics are the sphericity of the particles to be
manufactured and the control over their grain size. Nonetheless,
depending on the specifications defined for these spherical particles,
the GSP process has intrinsic limits, particularly when fabricating
very small particles. This paper describes the use of secondary
fragmentation (water, water/PVA and uranyl nitrate) on solid
surfaces under varying temperature and vibration conditions to assess
the relevance of using this new technique to manufacture very small
spherical particles by means of a modified GSP process. The
fragmentation mechanisms are monitored and analysed, before the
trends for its subsequent optimised application are described.
Abstract: In this paper, an analytical approach is used to study the coupled lateral-torsional vibrations of laminated composite beam. It is known that in such structures due to the fibers orientation in various layers, any lateral displacement will produce a twisting moment. This phenomenon is modeled by the bending-twisting material coupling rigidity and its main feature is the coupling of lateral and torsional vibrations. In addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies. Then, the governing differential equations are derived using the Hamilton-s principle and the mathematical model matches the Timoshenko beam model when neglecting the effect of bending-twisting rigidity. The equations of motion which form a system of three coupled PDEs are solved analytically to study the free vibrations of the beam in lateral and rotational modes due to the bending, as well as the torsional mode caused by twisting. The analytic solution is carried out in three steps: 1) assuming synchronous motion for the kinematic variables which are the lateral, rotational and torsional displacements, 2) solving the ensuing eigenvalue problem which contains three coupled second order ODEs and 3) imposing different boundary conditions related to combinations of simply, clamped and free end conditions. The resulting natural frequencies and mode shapes are compared with similar results in the literature and good agreement is achieved.
Abstract: The dynamic model of a drill in drilling process was
proposed and investigated in this study. To assure a good drilling quality, the vibration variation on the drill tips during high speed
drilling is needed to be investigated. A pre-twisted beam is used to
simulate the drill. The moving Winkler-Type elastic foundation is used to characterize the tip boundary variation in drilling. Due to the
variation of the drill depth, a time dependent dynamic model for the drill is proposed. Results simulated from this proposed model indicate that an abrupt natural frequencies drop are experienced as the drill tip
tough the workpiece, and a severe vibration is induced. The effects of parameters, e.g. drilling speed, depth, drill size and thrust force on the
drill tip responses studied.
Abstract: In this study, the adhesion of ice to solid substrates
with different surface properties is compared. Clear ice, similar to
atmospheric in-flight icing encounters, is accreted on the different
substrates under controlled conditions. The ice adhesion behavior is
investigated by means of a dynamic vibration testing technique with
an electromagnetic shaker initiating ice de-bonding in the interface
between the substrate and the ice. The results of the experiments
reveal that the affinity for ice accretion is significantly influenced by
the water contact angle of the respective sample.
Abstract: This work has been conducted to study on comfort level of drivers of suspended cabin tractor semitrailer. Some drivers suffer from low back pain caused by vibration. The practical significance of applying suspended cabin type of tractor semi trailer was tested at different road conditions, different speed as well as different load conditions for comfortable driver seat interface (x, y, z ) and the process parameters have been prioritized using Taguchi-s L27 orthogonal array. Genetic Algorithm (GA) is used to optimize the human comfort vibration of suspended cabin tractor semitrailer drivers. The practical significance of applying GA to human comfort to reaction of suspended cabin tractor semitrailer has been validated by means of computing the deviation between predicted and experimentally obtained human comfort to vibration. The optimized acceleration data indicate a little uncomfortable ride for suspended cabin tractor semitrailer.
Abstract: In most cases, it is considerably difficult to directly measure structural vibration with a lot of sensors because of complex
geometry, time and equipment cost. For this reason, this paper deals
with the problem of locating sensors on a plate model by four advanced sensor placement optimization (S.P.O) techniques. It also
suggests the evaluation index representing the characteristic of orthogonal between each of natural modes. The index value provides the assistance to selecting of proper S.P.O technique and optimal
positions for monitoring of dynamic systems without the experiment.
Abstract: An accurate procedure to determine free vibrations of
beams and plates is presented.
The natural frequencies are exact solutions of governing vibration
equations witch load to a nonlinear homogeny system.
The bilinear and linear structures considered simulate a bridge.
The dynamic behavior of this one is analyzed by using the theory of
the orthotropic plate simply supported on two sides and free on the
two others. The plate can be excited by a convoy of constant or
harmonic loads. The determination of the dynamic response of the
structures considered requires knowledge of the free frequencies and
the shape modes of vibrations. Our work is in this context. Indeed,
we are interested to develop a self-consistent calculation of the Eigen
frequencies.
The formulation is based on the determination of the solution of
the differential equations of vibrations. The boundary conditions
corresponding to the shape modes permit to lead to a homogeneous
system. Determination of the noncommonplace solutions of this
system led to a nonlinear problem in Eigen frequencies.
We thus, develop a computer code for the determination of the
eigenvalues. It is based on a method of bisection with interpolation
whose precision reaches 10 -12. Moreover, to determine the
corresponding modes, the calculation algorithm that we develop uses
the method of Gauss with a partial optimization of the "pivots"
combined with an inverse power procedure. The Eigen frequencies
of a plate simply supported along two opposite sides while
considering the two other free sides are thus analyzed. The results
could be generalized with the case of a beam by regarding it as a
plate with low width.
We give, in this paper, some examples of treated cases. The
comparison with results presented in the literature is completely
satisfactory.
Abstract: Numerical design optimization is a powerful tool that
can be used by engineers during any stage of the design process.
There are many different applications for structural optimization. A
specific application that will be discussed in the following paper is
experimental data matching. Data obtained through tests on a physical
structure will be matched with data from a numerical model of that
same structure. The data of interest will be the dynamic characteristics
of an antenna structure focusing on the mode shapes and modal
frequencies. The structure used was a scaled and simplified model of
the Karoo Array Telescope-7 (KAT-7) antenna structure.
This kind of data matching is a complex and difficult task. This
paper discusses how optimization can assist an engineer during the
process of correlating a finite element model with vibration test data.
Abstract: In this paper the problems associated with immunity
of embedded systems used in Motor-Drive systems are investigated
and appropriate solutions are presented. Integration of VSD motor
systems (Integral Motor) while partially reducing some of these
effects, adds to immunity problem of their embedded systems. Fail
safe operation of an Integral Motor in arduous industrial
environments is considered. In this paper an integral motor with a
unique design is proposed to overcome critical issues such as heat,
vibration and electromagnetic interference which are damaging to
sensitive electronics without requirement of any additional cooling
system. Advantages of the proposed Integral motor are compactness
of combo motor and drive system with no external cabling/wiring.
This motor provides a perfect shielding for least amount of radiated
emission. It has an inbuilt filter for EMC compliance and has been
designed to provide lower EMC noise for immunity of the internal
electronics as well as the other neighbouring systems.
Abstract: An investigation of noise in a micro stepping motor is
considered to study in this article. Because of the trend towards higher
precision and more and more small 3C (including Computer,
Communication and Consumer Electronics) products, the micro
stepping motor is frequently used to drive the micro system or the
other 3C products. Unfortunately, noise in a micro stepped motor is
too large to accept by the customs. To depress the noise of a micro
stepped motor, the dynamic characteristics in this system must be
studied. In this article, a Visual Basic (VB) computer program speed
controlled micro stepped motor in a digital camera is investigated.
Karman KD2300-2S non-contract eddy current displacement sensor,
probe microphone, and HP 35670A analyzer are employed to analyze
the dynamic characteristics of vibration and noise in a motor. The
vibration and noise measurement of different type of bearings and
different treatment of coils are compared. The rotating components,
bearings, coil, etc. of the motor play the important roles in producing
vibration and noise. It is found that the noise will be depressed about
3~4 dB and 6~7 dB, when substitutes the copper bearing with plastic
one and coats the motor coil with paraffin wax, respectively.
Abstract: Chaiyaphum Starch Co. Ltd. is one of many starch
manufacturers that has introduced machinery to aid in manufacturing.
Even though machinery has replaced many elements and is now a
significant part in manufacturing processes, problems that must be
solved with respect to current process flow to increase efficiency still
exist. The paper-s aim is to increase productivity while maintaining
desired quality of starch, by redesigning the flipping machine-s
mechanical control system which has grossly low functional lifetime.
Such problems stem from the mechanical control system-s bearings,
as fluids and humidity can access into said bearing directly, in
tandem with vibrations from the machine-s function itself. The wheel
which is used to sense starch thickness occasionally falls from its
shaft, due to high speed rotation during operation, while the shaft
may bend from impact when processing dried bread. Redesigning its
mechanical control system has increased its efficiency, allowing
quality thickness measurement while increasing functional lifetime
an additional 62 days.
Abstract: We present design, fabrication, and characterization of
a small (12 mm × 12 mm × 8 mm) movable railway vehicle for sensor
carrying. The miniature railway vehicle (MRV) was mainly composed
of a vibrational structure and three legs. A railway was designed and
fabricated to power and guide the MRV. It also transmits the sensed
data from the MRV to the signal processing unit. The MRV with legs
on the railway was moving due to its high-frequency vibration. A
model was derived to describe the motion. Besides, FEM simulations
were performed to design the legs. Then, the MRV and the railway
were fabricated by precision machining. Finally, an infrared sensor
was carried and tested. The result shows that the MRV without loading
was moving along the railway and its maximum speed was 12.2 mm/s.
Moreover, the testing signal was sensed by the MRV.
Abstract: This paper is concerned with propagation of thermoelastic longitudinal vibrations of an infinite circular cylinder, in the context of the linear theory of generalized thermoelasticity with two relaxation time parameters (Green and Lindsay theory). Three displacement potential functions are introduced to uncouple the equations of motion. The frequency equation, by using the traction free boundary conditions, is given in the form of a determinant involving Bessel functions. The roots of the frequency equation give the value of the characteristic circular frequency as function of the wave number. These roots, which correspond to various modes, are numerically computed and presented graphically for different values of the thermal relaxation times. It is found that the influences of the thermal relaxation times on the amplitudes of the elastic and thermal waves are remarkable. Also, it is shown in this study that the propagation of thermoelastic longitudinal vibrations based on the generalized thermoelasticity can differ significantly compared with the results under the classical formulation. A comparison of the results for the case with no thermal effects shows well agreement with some of the corresponding earlier results.
Abstract: This paper investigates the occurrence of regenerative
chatter vibrations in facing and turning processes. Orthogonal turning
(facing) and normal turning experiments are carried out under stable
as well as in the presence of controlled chatter vibrations. The effects
of chatter vibrations on various sensor signals are captured and
analyzed using frequency domain methods, which successfully
detected the chatter vibrations close to the dominant mode of the
machine tool system.
Abstract: A method based on the power series solution is proposed to solve the natural frequency of flapping vibration for the rotating inclined Euler beam with constant angular velocity. The vibration of the rotating beam is measured from the position of the corresponding steady state axial deformation. In this paper the governing equations for linear vibration of a rotating Euler beam are derived by the d'Alembert principle, the virtual work principle and the consistent linearization of the fully geometrically nonlinear beam theory in a rotating coordinate system. The governing equation for flapping vibration of the rotating inclined Euler beam is linear ordinary differential equation with variable coefficients and is solved by a power series with four independent coefficients. Substituting the power series solution into the corresponding boundary conditions at two end nodes of the rotating beam, a set of homogeneous equations can be obtained. The natural frequencies may be determined by solving the homogeneous equations using the bisection method. Numerical examples are studied to investigate the effect of inclination angle on the natural frequency of flapping vibration for rotating inclined Euler beams with different angular velocity and slenderness ratio.
Abstract: Real-time measurement of applied forces, like tension, compression, torsion, and bending moment, identifies the transferred energies being applied to the bottomhole assembly (BHA). These forces are highly detrimental to measurement/logging-while-drilling tools and downhole equipment. Real-time measurement of the dynamic downhole behavior, including weight, torque, bending on bit, and vibration, establishes a real-time feedback loop between the downhole drilling system and drilling team at the surface. This paper describes the numerical analysis of the strain data acquired by the measurement tool at different locations on the strain pockets. The strain values obtained by FEA for various loading conditions (tension, compression, torque, and bending moment) are compared against experimental results obtained from an identical experimental setup. Numerical analyses results agree with experimental data within 8% and, therefore, substantiate and validate the FEA model. This FEA model can be used to analyze the combined loading conditions that reflect the actual drilling environment.