Abstract: This article presents a method of using the one
dimensional piezo-electric patch on beam model for structural
identification. A hybrid element constituted of one dimensional
beam element and a PZT sensor is used with reduced material
properties. This model is convenient and simple for identification
of beams. Accuracy of this element is first verified against a
corresponding 3D finite element model (FEM). The structural
identification is carried out as an inverse problem whereby
parameters are identified by minimizing the deviation between
the predicted and measured voltage response of the patch, when
subjected to excitation. A non-classical optimization algorithm
Particle Swarm Optimization is used to minimize this objective
function. The signals are polluted with 5% Gaussian noise to
simulate experimental noise. The proposed method is applied on
beam structure and identified parameters are stiffness and damping.
The model is also validated experimentally.
Abstract: A torsional piezoelectric ultrasonic transducer design
is proposed to measure shear moduli in soft tissue with direct
access availability, using shear wave elastography technique. The
measurement of shear moduli of tissues is a challenging problem,
mainly derived from a) the difficulty of isolating a pure shear wave,
given the interference of multiple waves of different types (P, S,
even guided) emitted by the transducers and reflected in geometric
boundaries, and b) the highly attenuating nature of soft tissular
materials. An immediate application, overcoming these drawbacks,
is the measurement of changes in cervix stiffness to estimate the
gestational age at delivery. The design has been optimized using
a finite element model (FEM) and a semi-analytical estimator of
the probability of detection (POD) to determine a suitable geometry,
materials and generated waves. The technique is based on the time
of flight measurement between emitter and receiver, to infer shear
wave velocity. Current research is centered in prototype testing and
validation. The geometric optimization of the transducer was able
to annihilate the compressional wave emission, generating a quite
pure shear torsional wave. Currently, mechanical and electromagnetic
coupling between emitter and receiver signals are being the research
focus. Conclusions: the design overcomes the main described
problems. The almost pure shear torsional wave along with the short
time of flight avoids the possibility of multiple wave interference.
This short propagation distance reduce the effect of attenuation, and
allow the emission of very low energies assuring a good biological
security for human use.
Abstract: Below-knee amputees commonly experience
asymmetrical gait patterns. It is generally believed that ischemia is
related to the formation of pressure sores due to uneven distribution
of forces. Micro-vascular responses can reveal local malnutrition.
Changes in local skin blood supply under various external loading
conditions have been studied for a number of years. Radionuclide
clearance, photo-plethysmography, trans-cutaneous oxygen tension
along with other studies showed that the blood supply would be
influenced by the epidermal forces, and the rate and the amount of
blood supply would decrease with increased epidermal loads being
shear forces or normal forces. Several cases of socket designs were
investigated using Finite Element Model (FEM) and Design of
Experiment (DOE) to increase flexibility and minimize the pressure
at the limb/socket interface using ultra high molecular weight
polyethylene (UHMWPE) and polyamide 6 (PA6) or Duraform. The
pressure reliefs at designated areas where reducing thickness is
involved are seen to be critical in determination of amputees’ comfort
and are very important to clinical applications. Implementing a hole
between the Patellar Tendon (PT) and Distal Tibia (DT) would
decrease stiffness and increase prosthesis range of motion where
flexibility is needed. In addition, displacement and prosthetic energy
storage increased without compromising mechanical efficiency and
prosthetic design integrity.
Abstract: To understand the factors which affect impact damage on composite structures, particularly the effects of impact position and ribs. In this paper, a finite element model (FEM) of low-velocity impact damage on the composite structure was established via the nonlinear finite element method, combined with the user-defined materials subroutine (VUMAT) of the ABAQUS software. The structural elements chosen for the investigation comprised a series of stiffened composite panels, representative of real aircraft structure. By impacting the panels at different positions relative to the ribs, the effect of relative position of ribs was found out. Then the simulation results and the experiments data were compared. Finally, the factors which affect impact damage on the structures were discussed. The paper was helpful for the design of stiffened composite structures.
Abstract: This study evaluates the back calculation of stiffness of a pavement section on Interstate 40 (I-40)in New Mexico through numerical analysis. Falling Weight Deflectometer (FWD) test has been conducted on a section on I-40. Layer stiffness of the pavement has been backcalculated by a backcalculation software, ELMOD, using the FWD test data. Commercial finite element software, ABAQUS, has been used to develop the Finite Element Model (FEM) of this pavement section. Geometry and layer thickness are collected from field coring. Input parameters i.e. stiffnesses of different layers of the pavement are used as the backcalculated ones. Resulting surface deflections at different radial distances from the FEM analysis are compared with field FWD deflection values. It shows close agreement between the FEM and FWD outputs. Therefore, the FWD test method can be considered to be a reliable test procedure for evaluating the in situ stiffness of pavement material.
Abstract: Stiffness of Hot Mix Asphalt (HMA) in flexible pavement is largely dependent of temperature, mode of testing and age of pavement. Accurate measurement of HMA stiffness is thus quite challenging. This study determines HMA stiffness based on Finite Element Model (FEM) and validates the results using field data. As a first step, stiffnesses of different layers of a pavement section on Interstate 40 (I-40) in New Mexico were determined by Falling Weight Deflectometer (FWD) test. Pavement temperature was not measured at that time due to lack of temperature probe. Secondly, a FE model is developed in ABAQUS. Stiffness of the base, subbase and subgrade were taken from the FWD test output obtained from the first step. As HMA stiffness largely varies with temperature it was assigned trial and error approach. Thirdly, horizontal strain and vertical stress at the bottom of the HMA and temperature at different depths of the pavement were measured with installed sensors on the whole day on December 25th, 2012. Fourthly, outputs of FEM were correlated with measured stress-strain responses. After a number of trials a relationship was developed between the trial stiffness of HMA and measured mid-depth HMA temperature. At last, the obtained relationship between stiffness and temperature is verified by further FWD test when pavement temperature was recorded. A promising agreement between them is observed. Therefore, conclusion can be drawn that linear elastic FEM can accurately predict the stiffness and the structural response of flexible pavement.
Abstract: Numerical design optimization is a powerful tool that
can be used by engineers during any stage of the design process.
There are many different applications for structural optimization. A
specific application that will be discussed in the following paper is
experimental data matching. Data obtained through tests on a physical
structure will be matched with data from a numerical model of that
same structure. The data of interest will be the dynamic characteristics
of an antenna structure focusing on the mode shapes and modal
frequencies. The structure used was a scaled and simplified model of
the Karoo Array Telescope-7 (KAT-7) antenna structure.
This kind of data matching is a complex and difficult task. This
paper discusses how optimization can assist an engineer during the
process of correlating a finite element model with vibration test data.