Abstract: The rapid industrialisation and population growth have led to a steady fall in freshwater supplies worldwide. As a result, water systems are affected by modern methods upon use due to secondary contamination. The application of novel adsorbents derived from natural polymer holds a great promise in addressing challenges in water treatment. In this study, the UV irradiation technique was used to prepare acrylamide (AAm) monomer, and acrylic acid (AA) monomer grafted xanthan gum (XG) copolymer. Furthermore, the factors affecting rhodamine B (RhB) adsorption from aqueous media, such as pH, dosage, concentration, and time were also investigated. The FTIR results confirmed the formation of graft copolymer by the strong vibrational bands at 1709 cm-1 and 1612 cm-1 for AA and AAm, respectively. Additionally, more irregular, porous and wrinkled surface observed from SEM of XG-g-AAm/AA indicated copolymerization interaction of monomers. The optimum conditions for removing RhB dye with a maximum adsorption capacity of 313 mg/g at 25 0C from aqueous solution were pH approximately 5, initial dye concentration = 200 ppm, adsorbent dose = 30 mg. Also, the detailed investigation of the isothermal and adsorption kinetics of RhB from aqueous solution showed that the adsorption of the dye followed a Freundlich model (R2 = 0.96333) and pseudo-second-order kinetics. The results further indicated that this absorbent based on XG had the universality to remove dye through the mechanism of chemical adsorption. The outstanding adsorption potential of the grafted copolymer could be used to remove cationic dyes from aqueous solution as a low-cost product.
Abstract: During the past two decades, photoinitiated polymerization has been attracting a great interest in terms of scientific and industrial activity. The wide recognition of UV treatment in the polymer industry results not only from its many practical applications but also from its advantage for low-cost processes. Unlike most thermal curing systems, radiation-curable systems can polymerize at room temperature without additional heat, and the curing is completed in a very short time. The advantage of cationic UV technology is that post-cure can continue in the ‘dark’ after radiation. In this study, bio-based acrylated epoxidized soybean oil (AESO) was cured with UV radiation using radicalic photoinitiator Irgacure 184. Triarylsulphonium hexafluoroantimonate was used as cationic photoinitiator for curing of 3,4-epoxycyclohexylmethyl-3,4-epoxycyclohexanecarboxylate. The effect of curing time and the amount of initiators on the curing degree and thermal properties were investigated. The thermal properties of the coating were analyzed after crosslinking UV irradiation. The level of crosslinking in the coating was evaluated by FTIR analysis. Cationic UV-cured coatings demonstrated excellent adhesion and corrosion resistance properties. Therefore, our study holds a great potential with its simple and low-cost applications.
Abstract: This study attempts to understand the effect of different UV irradiation methods on the intercalation of LDPE/MMT nanocomposites, and its molecular behavior at certain isothermal crystallization temperature. Three different methods of UV exposure were employed using single composition of LDPE/MMT nanocomposites. All samples were annealed for 5 hours at a crystallization temperature of 100oC. The crystallization temperature was chosen to be at large supercooling temperature to ensure quick and complete crystallization. The raw material of LDPE consisted of two stable monoclinic and orthorhombic phases according to XRD results. The thermal behavior of both phases acted differently when UV exposure method was changed. The monoclinic phase was more dependent on the method used compared to the orthorhombic phase. The intercalation of clay, as well as, the non-isothermal crystallization temperature, has also shown a clear dependency on the type of UV exposure. A third phase that is thermally less stable was also observed. Its respond to UV irradiation was greater since it contains low molecular weight entities which make it more vulnerable to any UV exposure.
Abstract: Si ion implantation was widely used to synthesize
specimens of SiO2 containing supersaturated Si and subsequent high
temperature annealing induces the formation of embedded
luminescent Si nanocrystals. In this work, the potentialities of excimer
UV-light (172 nm, 7.2 eV) irradiation and rapid thermal annealing
(RTA) to enhance the photoluminescence and to achieve low
temperature formation of Si nanocrystals have been investigated. The
Si ions were introduced at acceleration energy of 180 keV to fluence of
7.5 x 1016 ions/cm2. The implanted samples were subsequently
irradiated with an excimer-UV lamp. After the process, the samples
were rapidly thermal annealed before furnace annealing (FA).
Photoluminescence spectra were measured at various stages at the
process. We found that the luminescence intensity is strongly
enhanced with excimer-UV irradiation and RTA. Moreover, effective
visible photoluminescence is found to be observed even after FA at
900 oC, only for specimens treated with excimer-UV lamp and RTA.
We also prepared specimens of Si nanocrystals embedded in a SiO2 by
reactive pulsed laser deposition (PLD) in an oxygen atmosphere. We
will make clear the similarities and differences with the way of
preparation.
Abstract: Thin ZnO films are deposited on glass substrates via
sol–gel method and dip-coating. The films are prepared from zinc
acetate dehydrate as a starting reagent. After that the as-prepared
ZnO sol is aged for different periods (0, 1, 3, 5, 10, 15 and 30 days).
Nanocrystalline thin films are deposited from various sols. The
effect ZnO sols aging time on the structural and photocatalytic
properties of the films is studied. The films surface is studied by
Scanning Electron Microscopy. The effect of the aging time of the
starting solution is studied in the photocatalytic degradation of
Reactive Black 5 (RB5) by UV-vis spectroscopy. The experiments
are conducted upon UV-light illumination and in complete darkness.
The variation of the absorption spectra shows the degradation of RB5
dissolved in water, as a result of the reaction, occurring on the surface
of the films and promoted by UV irradiation. The initial
concentrations of dye (5, 10 and 20 ppm) and the effect of the aging
time are varied during the experiments. The results show, that the
increasing aging time of starting solution with respect to ZnO
generally promotes photocatalytic activity. The thin films obtained
from ZnO sol, which is aged 30 days have best photocatalytic
degradation of the dye (97,22%) in comparison with the freshly
prepared ones (65,92%). The samples and photocatalytic
experimental results are reproducible. Nevertheless, all films exhibit
a substantial activity in both UV light and darkness, which is
promising for the development of new ZnO photocatalysts by sol-gel
method.
Abstract: Ficus deltoidea from the Moraceae family is a popular
medicinal herb in Malaysia. It possesses strong antioxidant and antiinflammatory
properties. In the present study, the anti-inflammatory
effects of F. deltoidea extract on UVB-irradiated HaCaT
Keratinocytes were investigated. HaCaT Keratinocytes were UVBirradiated
(12.5 mJ/cm3) and were treated with 0.05, 0.08 or 0.1% of
F. deltoidea extract. Cell viability following UVB irradiation was
significantly higher in the groups treated with the F. deltoidea extract
at doses of 0.05, 0.08 or 0.1% than in control group with UVB
irradiation only. Tumor necrosis factor-α (TNF-α), interleukin-1α
(IL-1α), interleukin-6 (IL-6) and cyclooxygenase (COX-2) play
primary roles in the inflammation process upon UV irradiation and
are known to be stimulated by UVB irradiation. Treatment with the
F. deltoidea extract dramatically inhibited the UV-induced TNF-α,
IL-1α, IL-6, and COX-2 expression. These results suggest that the F.
deltoidea extract inhibits the production of pro-inflammatory
cytokines and may be an effective protective agent for the treatment
of skin diseases.
Abstract: Overhead electrical insulators form an important link in an electric power system. Along with the traditional insulators (i.e. glass and porcelain, etc) presently the polymeric insulators are also used world widely. These polymeric insulators are very sensitive to various environmental parameters such temperature, environmental pollution, UV-radiations, etc. which seriously effect their electrical, chemical and hydrophobic properties. The UV radiation level in the central region of Saudi Arabia is high as compared to the IEC standard for the accelerated aging of the composite insulators. Commonly used suspension type of composite EPDM (Ethylene Propylene Diene Monomer) insulator was subjected to accelerated stress aging as per modified IEC standard simulating the inland arid deserts atmospheric condition and also as per IEC-61109 standard. The hydrophobic characteristics were studied by measuring the contact angle along the insulator surface before and after the accelerated aging of the samples. It was found that EPDM insulator loses it hydrophobic properties proportional to the intensity of UV irradiations and its rate of recovery is also very low as compared to Silicone Rubber insulator.KeywordsEPDM, composite insulators, accelerated aging, hydrophobicity, contact angle.
Abstract: ZnO nanostructure were synthesized via microwave
method using zinc acetate as starting material, guanidinium as
structure directing agents, and water as solvent.. This work
investigates the photodegradation of azo dyes using the ZnO Flowerlike
in aqueous solutions. As synthesized ZnO samples were
characterized using X-Ray powder diffraction (XRD), scanning
electron microscopy (SEM), and FTIR spectroscopy.In this work
photodecolorization of congored azo dye under UV irradiation by
nano ZnO was studied.
Abstract: Cu-mesoporous TiO2 is developed for removal acid
odor cooperated with ozone assistance and online- regeneration
system with/without UV irradiation (all weather) in study. The results
showed that Cu-mesoporous TiO2 present the desirable adsorption
efficiency of acid odor without UV irradiation, due to the larger
surface area, pore sizeand the additional absorption ability provided by
Cu. In the photocatalysis process, the material structure also benefits
Cu-mesoporous TiO2 to perform the more outstanding efficiency on
degrading acid odor. Cu also postponed the recombination of
electron-hole pairs excited from TiO2 to enhance photodegradation
ability. Cu-mesoporous TiO2 could gain the conspicuous increase on
photocatalysis ability from ozone assistance, but without any benefit
on adsorption. In addition, the online regeneration procedure could
process the used Cu-mesoporous TiO2 to reinstate the adsorption
ability and maintain the photodegradtion performance, depended on
scrubbing, desorping acid odor and reducing Cu to metal state.
Abstract: A study concerning the photocatalytic decolourization
of Congo red (CR) dye, over artificial UV irradiation is presented.
Photocatalysts based on a commercial titanium dioxide (TiO2)
modified with transition metals (Ni, Cu and Zn) were used. The
dopage method used was wet impregnation. A TiO2 sample without
salt was subjected to the same hydrothermal treatment to be used as
reference. Congo red solutions to several pH conditions (natural and
basic) were used to evaluate photocatalytic performance of each
doped catalysts. Photodecolourization percentage was measured
spectrofotrometically after 3 h of treatment to 499 nm as response
variable. Kinetics investigations of photodegradation indicated that
reactions obey to Langmuir-Hinshelwood model and pseudo–first
order law. The rate constant studies of photocatalytic decolourization
reactions for Zn–TiO2 and Cu–TiO2 photocatalysts indicated that in
all cases the rate constant of the reaction was higher than that of TiO2
undoped. These results show that nature of the metal modifying the
TiO2 influence on the efficiency of the photocatalyst evaluated in
process. Ni does not present an additional effect compared with TiO2,
while Zn enhances the photoactivity due to its electronic properties.