Abstract: This paper deals with the harmonic decontamination of current in an electrical grid by an active shunt filter in order to improve power quality. The contribution of this paper is mainly based on the proposal of a control strategy for an active filter based on Duty Cycle Modulation (DCM). First, three-monophase method is applied for the identification of disturbing currents. A Simulink model of this method is given for one phase of the grid. Secondly, two orders were designed: the first one is the Hysteresis Control and the second one is the DCM Control. Finally, a comparative study of the two controls was performed. The results obtained show a significant improvement in the rate of harmonic distortion for both controls. The harmonic distortion for the Hysteresis control is limited by the non-controllability of the switching frequencies of the inverter's switches and reduces the harmonic distortion rate (THD) to 3.12% as opposed to the DCM control which limits the THD to 2.82% which makes it better.
Abstract: Here a methodology is considered aiming at evaluating the economic benefit of the provision of a primary frequency control unit using a Battery Energy Storage System (BESS). In this methodology, two control types (basic and hysteresis) are implemented and the corresponding minimum energy storage system power allowing to maintain the frequency drop inside a given threshold under a given contingency is identified and compared using DigSilent’s PowerFactory software. Following this step, the corresponding energy storage capacity (in MWh) is calculated. As PowerFactory is dedicated to dynamic simulation for transient analysis, a first order model related to the IEEE 9 bus grid used for the analysis under PowerFactory is characterized and implemented on MATLAB-Simulink. Primary frequency control is simulated using the two control types over one-month grid's frequency deviation data on this Simulink model. This simulation results in the energy throughput both basic and hysteresis BESSs. It emerges that the 15 minutes operation band of the battery capacity allocated to frequency control is sufficient under the considered disturbances. A sensitivity analysis on the width of the control deadband is then performed for the two control types. The deadband width variation leads to an identical sizing with the hysteresis control showing a better frequency control at the cost of a higher delivered throughput compared to the basic control. An economic analysis comparing the cost of the sized BESS to the potential revenues is then performed.
Abstract: Traveling Wave Ultrasonic Motor (TWUM) is a compact, precise, and silent actuator generating high torque at low speed without gears. Moreover, the TWUM has a high holding torque without supply, which makes this motor as an attractive solution for holding position of robotic arms. However, their nonlinear dynamics, and the presence of load-dependent dead zones often limit their use. Those issues can be overcome in closed loop with effective and precise controllers. In this paper, robust H-infinity (H∞) and discrete time RST position controllers are presented. The H∞ controller is designed in continuous time with additional weighting filters to ensure the robustness in the case of uncertain motor model and external disturbances. Robust RST controller based on the pole placement method is also designed and compared to the H∞. Simulink model of TWUM is used to validate the stability and the robustness of the two proposed controllers.
Abstract: This study presents a procedure for friction calculation of column electric power steering (C-EPS) system which affects handling and comfort in driving. The friction losses estimation is obtained from experimental tests and mathematical calculation. Parts in C-EPS mainly involved in friction losses are bearings and worm gear. In the theoretical approach, the gear geometry and Hertz law were employed to measure the normal load and the sliding velocity and contact areas from the worm gears driving conditions. The viscous friction generated in the worm gear was obtained with a theoretical approach and the result was applied to model the friction in the steering system. Finally, by viscous friction coefficient and Coulomb friction coefficient, values of friction in worm gear were calculated. According to the Bearing Company and the characteristics of each bearing, the friction torques due to load and due to speed were calculated. A MATLAB Simulink model for calculating the friction in bearings and worm gear in C-EPS were done and the total friction value was estimated.
Abstract: Among various active filters, shunt active filter is a
viable solution for reactive power and harmonics compensation. In
this paper, the SRF plan is used to generate current reference for
compensation and conventional PI controllers were used as the
controller to compensate the reactive power. The design of the closed
loop controllers is reserved simple by modeling them as first order
systems. Computationally uncomplicated and efficient SVM system
is used in the present work for better utilization of dc bus voltage.
The rating of shunt active filter has been finalized based on the
reactive power demand of the selected reactive load. The proposed
control and SVM technique are validated by simulating in MATLAB
software.
Abstract: Parabolic solar trough systems have seen limited
deployments in cold northern climates as they are more suitable for
electricity production in southern latitudes. A numerical dynamic
model is developed to simulate troughs installed in cold climates and
validated using a parabolic solar trough facility in Winnipeg. The
model is developed in Simulink and will be utilized to simulate a trigeneration
system for heating, cooling and electricity generation in
remote northern communities. The main objective of this simulation
is to obtain operational data of solar troughs in cold climates and use
the model to determine ways to improve the economics and address
cold weather issues.
In this paper the validated Simulink model is applied to simulate a
solar assisted absorption cooling system along with electricity
generation using Organic Rankine Cycle (ORC) and thermal storage.
A control strategy is employed to distribute the heated oil from solar
collectors among the above three systems considering the
temperature requirements. This modelling provides dynamic
performance results using measured meteorological data recorded
every minute at the solar facility location. The purpose of this
modeling approach is to accurately predict system performance at
each time step considering the solar radiation fluctuations due to
passing clouds. Optimization of the controller in cold temperatures is
another goal of the simulation to for example minimize heat losses in
winter when energy demand is high and solar resources are low.
The solar absorption cooling is modeled to use the generated heat
from the solar trough system and provide cooling in summer for a
greenhouse which is located next to the solar field.
The results of the simulation are presented for a summer day in
Winnipeg which includes comparison of performance parameters of
the absorption cooling and ORC systems at different heat transfer
fluid (HTF) temperatures.
Abstract: Robotic surgery is used to enhance minimally invasive
surgical procedure. It provides greater degree of freedom for surgical
tools but lacks of haptic feedback system to provide sense of touch to
the surgeon. Surgical robots work on master-slave operation, where
user is a master and robotic arms are the slaves. Current, surgical
robots provide precise control of the surgical tools, but heavily rely
on visual feedback, which sometimes cause damage to the inner
organs. The goal of this research was to design and develop a realtime
Simulink based robotic system to study force feedback
mechanism during instrument-object interaction. Setup includes three
VelmexXSlide assembly (XYZ Stage) for three dimensional
movement, an end effector assembly for forceps, electronic circuit for
four strain gages, two Novint Falcon 3D gaming controllers,
microcontroller board with linear actuators, MATLAB and Simulink
toolboxes. Strain gages were calibrated using Imada Digital Force
Gauge device and tested with a hard-core wire to measure
instrument-object interaction in the range of 0-35N. Designed
Simulink model successfully acquires 3D coordinates from two
Novint Falcon controllers and transfer coordinates to the XYZ stage
and forceps. Simulink model also reads strain gages signal through
10-bit analog to digital converter resolution of a microcontroller
assembly in real time, converts voltage into force and feedback the
output signals to the Novint Falcon controller for force feedback
mechanism. Experimental setup allows user to change forward
kinematics algorithms to achieve the best-desired movement of the
XYZ stage and forceps. This project combines haptic technology
with surgical robot to provide sense of touch to the user controlling
forceps through machine-computer interface.
Abstract: A Space Vector based Pulse Width Modulation
control technique for the three-phase PWM converter is proposed in
this paper. The proposed control scheme is based on a synchronous
reference frame model. High performance and efficiency is obtained
with regards to the DC bus voltage and the power factor
considerations of the PWM rectifier thus leading to low losses.
MATLAB/SIMULINK are used as a platform for the simulations and
a SIMULINK model is presented in the paper. The results show that
the proposed model demonstrates better performance and properties
compared to the traditional SPWM method and the method improves
the dynamic performance of the closed loop drastically.
For the Space Vector based Pulse Width Modulation, Sine signal
is the reference waveform and triangle waveform is the carrier
waveform. When the value sine signal is large than triangle signal,
the pulse will start produce to high. And then when the triangular
signals higher than sine signal, the pulse will come to low. SPWM
output will changed by changing the value of the modulation index
and frequency used in this system to produce more pulse width. The
more pulse width produced, the output voltage will have lower
harmonics contents and the resolution increase.
Abstract: This paper deals with the design of a moving sliding
surface in a variable structure plant for a second order system. The
chattering phenomena is also dealt with during the switching process
for an unstable sliding surface condition. The simulation examples
considered in this paper shows the effectiveness of the sliding mode
control method used for the design of the moving sliding surfaces. A
simulink model of the continuous system was also developed in
MATLAB-SIMULINK for the design and hence demonstrated. The
phase portraits and the state plots shows the demonstration of
the powerful control technique which can be applied for second
order systems.
Abstract: Temperature is one of the most principle factors affects aquaculture system. It can cause stress and mortality or superior environment for growth and reproduction. This paper presents the control of pond water temperature using artificial intelligence technique. The water temperature is very important parameter for shrimp growth. The required temperature for optimal growth is 34oC, if temperature increase up to 38oC it cause death of the shrimp, so it is important to control water temperature. Solar thermal water heating system is designed to supply an aquaculture pond with the required hot water in Mersa Matruh in Egypt. Neural networks are massively parallel processors that have the ability to learn patterns through a training experience. Because of this feature, they are often well suited for modeling complex and non-linear processes such as those commonly found in the heating system. Artificial neural network is proposed to control water temperature due to Artificial intelligence (AI) techniques are becoming useful as alternate approaches to conventional techniques. They have been used to solve complicated practical problems. Moreover this paper introduces a complete mathematical modeling and MATLAB SIMULINK model for the aquaculture system. The simulation results indicate that, the control unit success in keeping water temperature constant at the desired temperature by controlling the hot water flow rate.
Abstract: Fault tree analysis is a well-known method for
reliability and safety assessment of engineering systems. In the last 3
decades, a number of methods have been introduced, in the literature,
for automatic construction of fault trees. The main difference between these methods is the starting model from which the tree is constructed. This paper presents a new methodology for the construction of static and dynamic fault trees from a system Simulink
model. The method is introduced and explained in detail, and its correctness and completeness is experimentally validated by using an example, taken from literature. Advantages of the method are also mentioned.
Abstract: This paper is proposed the dynamic simulation of
small power induction motor based on Mathematical modeling. The
dynamic simulation is one of the key steps in the validation of the
design process of the motor drive systems and it is needed for
eliminating inadvertent design mistakes and the resulting error in the
prototype construction and testing. This paper demonstrates the
simulation of steady-state performance of induction motor by
MATLAB Program Three phase 3 hp induction motor is modeled
and simulated with SIMULINK model.
Abstract: A new observer based fault detection and diagnosis
scheme for predicting induction motors- faults is proposed in this
paper. Prediction of incipient faults, using different variants of
Kalman filter and their relative performance are evaluated. Only soft
faults are considered for this work. The data generation, filter
convergence issues, hypothesis testing and residue estimates are
addressed. Simulink model is used for data generation and various
types of faults are considered. A comparative assessment of the
estimates of different observers associated with these faults is
included.
Abstract: Wheeled Mobile Robots (WMRs) are built with their
Wheels- drive machine, Motors. Depend on their desire design of
WMR, Technicians made used of DC Motors for motion control. In
this paper, the author would like to analyze how to choose DC motor
to be balance with their applications of especially for WMR.
Specification of DC Motor that can be used with desire WMR is to
be determined by using MATLAB Simulink model. Therefore, this
paper is mainly focus on software application of MATLAB and
Control Technology. As the driving system of DC motor, a
Peripheral Interface Controller (PIC) based control system is
designed including the assembly software technology and H-bridge
control circuit. This Driving system is used to drive two DC gear
motors which are used to control the motion of WMR. In this
analyzing process, the author mainly focus the drive system on
driving two DC gear motors that will control with Differential Drive
technique to the Wheeled Mobile Robot . For the design analysis of
Motor Driving System, PIC16F84A is used and five inputs of sensors
detected data are tested with five ON/OFF switches. The outputs of
PIC are the commands to drive two DC gear motors, inputs of Hbridge
circuit .In this paper, Control techniques of PIC
microcontroller and H-bridge circuit, Mechanism assignments of
WMR are combined and analyzed by mainly focusing with the
“Modeling and Simulink of DC Motor using MATLAB".
Abstract: Nowadays Multilevel inverters are widely using in various applications. Modulation strategy at fundamental switching frequency like, SHEPWM is prominent technique to eliminate lower order of harmonics with less switching losses and better harmonic profile. The equations which are formed by SHE are highly nonlinear transcendental in nature, there may exist single, multiple or even no solutions for a particular MI. However, some loads such as electrical drives, it is required to operate in whole range of MI. In order to solve SHE equations for whole range of MI, intelligent techniques are well suited to solve equations so as to produce lest %THDV. Hence, this paper uses Continuous genetic algorithm for minimising harmonics. This paper also presents wavelet based analysis of harmonics. The developed algorithm is simulated and %THD from FFT analysis and Wavelet analysis are compared. MATLAB programming environment and SIMULINK models are used whenever necessary.
Abstract: A basic conceptual study of TCSC device on Simulink is a teaching aid and helps in understanding the rudiments of the topic. This paper thus stems out from basics of TCSC device and analyzes the impedance characteristics and associated single & multi resonance conditions. The Impedance characteristics curve is drawn for different values of inductance in MATLAB using M-files. The study is also helpful in estimating the appropriate inductance and capacitance values which have influence on multi resonance point in TCSC device. The capacitor voltage, line current, thyristor current and capacitor current waveforms are discussed briefly as simulation results. Simulink model of TCSC device is given and corresponding waveforms are analyzed. The subsidiary topics e.g. power oscillation damping, SSR mitigation and transient stability is also brought out.
Abstract: In this paper, we proposed an efficient data
compression strategy exploiting the multi-resolution characteristic of
the wavelet transform. We have developed a sensor node called
“Smart Sensor Node; SSN". The main goals of the SSN design are
lightweight, minimal power consumption, modular design and robust
circuitry. The SSN is made up of four basic components which are a
sensing unit, a processing unit, a transceiver unit and a power unit.
FiOStd evaluation board is chosen as the main controller of the SSN
for its low costs and high performance. The software coding of the
implementation was done using Simulink model and MATLAB
programming language. The experimental results show that the
proposed data compression technique yields recover signal with good
quality. This technique can be applied to compress the collected data
to reduce the data communication as well as the energy consumption
of the sensor and so the lifetime of sensor node can be extended.
Abstract: This paper discusses coordinated reactive power -
voltage (Q-V) control in a multi machine steam power plant. The
drawbacks of manual Q-V control are briefly listed, and the design
requirements for coordinated Q-V controller are specified.
Theoretical background and mathematical model of the new
controller are presented next followed by validation of developed
Matlab/Simulink model through comparison with recorded
responses in real steam power plant and description of practical
realisation of the controller. Finally, the performance of
commissioned controller is illustrated on several examples of
coordinated Q-V control in real steam power plant and compared
with manual control.
Abstract: The paper presents a new system for the automat
control of the aircrafts- flight in lateral plane using the cinematic
model and the dynamic inversion. Starting from the equations of the
aircrafts- lateral movement, the authors use two axes systems and
obtained a control law that cancels the lateral deviation of the flying
objects from the runway line. This system makes the aircrafts-
direction angle to follow the direction angle of the runway line.
Simulations in Matlab/Simulink have been done for different
aircraft-s initial points and direction angles. The inconvenience of
this system is the long duration of the “transient regime". That is why
this system can be used independently, but the results are not very
good; thus, it can be a part (subsystem) of other systems. The main
system that cancels the lateral deviation from the runway line is
based on dynamic inversion and uses, as subsystem, the control
system for the lateral movement using the cinematic model. Using
complex Matlab/Simulink models, the authors obtained the time
evolution of the direction angle and the time evolution of the aircraft
lateral deviation with respect to the runway line, for different values
of the initial direction angle and for different wind types. The system
has a very good behavior for all initial direction angles and wind
types.
Abstract: The paper describes the evaluation of quality of
control for cases of controlled non-minimal phase plants. Control
circuits containing non-minimal phase plants have different
properties, they manifest reversed reaction at the beginning of unit
step response. For these types of plants are developed special
criterion of quality of control, which considers the difference and can
be helpful for synthesis of optimal controller tuning. All results are
clearly presented using Matlab/Simulink models.