Abstract: This paper investigates the application of Particle Swarm Optimization (PSO) technique for coordinated design of a Power System Stabilizer (PSS) and a Thyristor Controlled Series Compensator (TCSC)-based controller to enhance the power system stability. The design problem of PSS and TCSC-based controllers is formulated as a time domain based optimization problem. PSO algorithm is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. To compare the capability of PSS and TCSC-based controller, both are designed independently first and then in a coordinated manner for individual and coordinated application. The proposed controllers are tested on a weakly connected power system. The eigenvalue analysis and non-linear simulation results are presented to show the effectiveness of the coordinated design approach over individual design. The simulation results show that the proposed controllers are effective in damping low frequency oscillations resulting from various small disturbances like change in mechanical power input and reference voltage setting.
Abstract: In this paper the supersonic ejectors are
experimentally and analytically studied. Ejector is a device that
uses the energy of a fluid to move another fluid. This device works
like a vacuum pump without usage of piston, rotor or any other
moving component. An ejector contains an active nozzle, a passive
nozzle, a mixing chamber and a diffuser. Since the fluid viscosity
is large, and the flow is turbulent and three dimensional in the
mixing chamber, the numerical methods consume long time and
high cost to analyze the flow in ejectors. Therefore this paper
presents a simple analytical method that is based on the precise
governing equations in fluid mechanics. According to achieved
analytical relations, a computer code has been prepared to analyze
the flow in different components of the ejector. An experiment has
been performed in supersonic regime 1.5
Abstract: In this paper, application of Sliding Mode Control (SMC) technique for an Active Magnetic Bearing (AMB) system with varying rotor speed is considered. The gyroscopic effect and mass imbalance inherited in the system is proportional to rotor speed in which this nonlinearity effect causes high system instability as the rotor speed increases. Transformation of the AMB dynamic model into regular system shows that these gyroscopic effect and imbalance lie in the mismatched part of the system. A H2-based sliding surface is designed which bound the mismatched parts. The solution of the surface parameter is obtained using Linear Matrix Inequality (LMI). The performance of the controller applied to the AMB model is demonstrated through simulation works under various system conditions.
Abstract: This work presents a comparison between the Annual
Energy Output (AEO) of two commercial vertical-axis wind turbines
(VAWTs) for a low-wind urban site: both a drag-driven and a liftdriven
concepts are examined in order to be installed on top of the
new Via dei Giustinelli building, Trieste (Italy). The power-curves,
taken from the product specification sheets, have been matched to the
wind characteristics of the selected installation site. The influence of
rotor swept area and rated power on the performance of the two
proposed wind turbines have been examined in detail, achieving a
correlation between rotor swept area, electrical generator size and
wind distribution, to be used as a guideline for the calculation of the
AEO.
Abstract: Control of commutation of switched reluctance (SR)
motor has been an area of interest for researchers for sometime now
with mixed successes in addressing the inherent challenges. New
technologies, processing schemes and methods have been adopted to
make sensorless SR drive a reality. There are a number of
conceptual, offline, analytical and online solutions in literature that
have varying complexities and achieved equally varying degree of
robustness and accuracies depending on the method used to address
the challenges and the SR drive application. Magnetic coupling is
one such challenge when using active probing techniques to
determine rotor position of a SR motor from stator winding. This
paper studies the effect of back-of-core saturation on the detected
rotor position and presents results on measurement made on a 4-
phase SR motor. The results shows that even for a four phase motor
which is excited one phase at a time and using the electrically
opposite phase for active position probing, the back-of-core
saturation effects should not be ignored.
Abstract: In this paper, we analyze the rotor eddy currents losses provoqued by the stator slot harmonics developed in the permanent magnets or pole pieces of synchronous machines. An analytical approach is presented to evaluate the effect of slot ripples on rotor field and losses calculation. This analysis is then tested on a model by 2D/3D finite element (FE) calculation. The results show a good agreement on loss calculations when skin effect is negligible and the magnet is considered.
Abstract: In this paper, we investigated vector control of an induction machine taking into account discretization problems of the command. In the purpose to show how to include in a discrete model of this current control and with rotor time constant update. The results of simulation obtained are very satisfaisant. That was possible thanks to the good choice of the values of the parameters of the regulators used which shows, the founded good of the method used, for the choice of the parameters of the discrete regulators. The simulation results are presented at the end of this paper.
Abstract: This paper examines the use of mechanical aerator for
oxidation-ditch process. The rotor, which controls the aeration, is the
main component of the aeration process. Therefore, the objective of
this study is to find out the variations in overall oxygen transfer
coefficient (KLa) and aeration efficiency (AE) for different
configurations of aerator by varying the parameters viz. speed of
aerator, depth of immersion, blade tip angles so as to yield higher
values of KLa and AE. Six different configurations of aerator were
developed and fabricated in the laboratory and were tested for abovementioned
parameters. The curved blade rotor (CBR) emerged as a
potential aerator with blade tip angle of 47°.
The mathematical models are developed for predicting the
behaviour of CBR w.r.t kLa and power. In laboratory studies, the
optimum value of KLa and AE were observed to be 10.33 h-1 and
2.269 kg O2/ kWh.
Abstract: In this paper a sliding-mode torque and flux control is
designed for encoderless synchronous reluctance motor drive. The
sliding-mode plus PI controllers are designed in the stator-flux field
oriented reference frame which is able to track the mentioned
reference signals with a minimum pulsations in the state condition. In
addition, with these controllers a fast dynamic response is also
achieved for the drive system. The proposed control scheme is robust
subject to parameters variation except to stator resistance. To solve
this problem a simple estimator is used for on-line detecting of this
parameter. Moreover, the rotor position and speed are estimated by
on-line obtaining of the stator-flux-space vector. The effectiveness
and capability of the proposed control approach is verified by both
the simulation and experimental results.
Abstract: This paper details a new concept of using compressed air as a potential zero pollution power source for motorbikes. In place of an internal combustion engine, the motorbike is equipped with an air turbine transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor diameters, casing diameters and ratio of rotor to casing diameters of the turbine have been considered and analyzed. It is concluded that the work output is found optimum for some typical values of rotor / casing diameter ratios. In this study, the maximum power works out to 3.825 kW (5.20 HP) for casing diameter of 200 mm and rotor to casing diameter ratio of 0.65 to 0.60 which is sufficient to run motorbike.
Abstract: This paper addresses control of commutation of switched reluctance (SR) motor without the use of a physical position detector. Rotor position detection schemes for SR motor based on magnetisation characteristics of the motor use normal excitation or applied current /voltage pulses. The resulting schemes are referred to as passive or active methods respectively. The research effort is in realizing an economical sensorless SR rotor position detector that is accurate, reliable and robust to suit a particular application. An effective and reliable means of generating commutation signals of an SR motor based on inductance profile of its stator windings determined using active probing technique is presented. The scheme has been validated online using a 4-phase 8/6 SR motor and an 8-bit processor.
Abstract: Two-dimensional heat conduction within a composed solid material with a constant internal heat generation has been investigated numerically in a sector of the rotor a generator. The heat transfer between two adjacent materials is assumed to be purely conduction. Boundary conditions are assumed to be forced convection on the fluid side and adiabatic on symmetry lines. The control volume method is applied for the diffusion energy equation. Physical coordinates are transformed to the general curvilinear coordinates. Then by using a line-by-line method, the temperature distribution in a sector of the rotor has been determined. Finally, the results are normalized and the effect of cooling fluid on the maximum temperature of insulation is investigated.
Abstract: Over the course of the past century, the global
automotive industry-s stance towards safety has evolved from one of
contempt to one nearing reverence. A suspension system that
provides safe handling and cornering capabilities can, with the help
of an efficient braking system, improve safety to a large extent. The
aim of this research is to propose a new automotive brake rotor
design and to compare it with automotive vented disk rotor. Static
structural and transient thermal analysis have been carried out on the
vented disk rotor and proposed rotor designs to evaluate and compare
their performance. Finite element analysis was employed for both
static structural and transient thermal analysis. Structural analysis
was carried out to study the stress and deformation pattern of the
rotors under extreme loads. Time varying temperature load was
applied on the rotors and the temperature distribution was analysed
considering cooling parameters (convection and radiation). This
dissertation illustrates the use of Finite Element Methods to examine
models, concluding with a comparative study of the proposed rotor
design and the conventional vented disk rotor for structural stability
and thermal efficiency.
Abstract: This paper focuses on a critical component of the situational awareness (SA), the control of autonomous vertical flight for tactical unmanned aerial vehicle (TUAV). With the SA strategy, we proposed a two stage flight control procedure using two autonomous control subsystems to address the dynamics variation and performance requirement difference in initial and final stages of flight trajectory for an unmanned helicopter model with coaxial rotor and ducted fan configuration. This control strategy for chosen model of TUAV has been verified by simulation of hovering maneuvers using software package Simulink and demonstrated good performance for fast stabilization of engines in hovering, consequently, fast SA with economy in energy can be asserted during search-and-rescue operations.
Abstract: The incorporation of renewable energy sources for the sustainable electricity production is undertaking a more prominent role in electric power systems. Thus, it will be an indispensable incident that the characteristics of future power networks, their prospective stability for instance, get influenced by the imposed features of sustainable energy sources. One of the distinctive attributes of the sustainable energy sources is exhibiting the stochastic behavior. This paper investigates the impacts of this stochastic behavior on the small disturbance rotor angle stability in the upcoming electric power networks. Considering the various types of renewable energy sources and the vast variety of system configurations, the sensitivity analysis can be an efficient breakthrough towards generalizing the effects of new energy sources on the concept of stability. In this paper, the definition of small disturbance angle stability for future power systems and the iterative-stochastic way of its analysis are presented. Also, the effects of system parameters on this type of stability are described by performing a sensitivity analysis for an electric power test system.
Abstract: In this paper, we show that the association of the PI
regulators for the speed and stator currents with a control strategy
using the linearization by state feedback for an induction machine
without speed sensor, and with an adaptation of the rotor resistance.
The rotor speed is estimated by using the model reference adaptive
system approach (MRAS). This method consists of using two
models: The first is the reference model and the second is an
adjustable one in which two components of the stator flux, obtained
from the measurement of the currents and stator voltages are
estimated. The estimated rotor speed is then obtained by canceling
the difference between stator-flux of the reference model and those
of the adjustable one. Satisfactory results of simulation are obtained
and discussed in this paper to highlight the proposed approach.
Abstract: In this paper, stabilization of an Active Magnetic Bearing (AMB) system with varying rotor speed using Sliding Mode Control (SMC) technique is considered. The gyroscopic effect inherited in the system is proportional to rotor speed in which this nonlinearity effect causes high system instability as the rotor speed increases. Also, transformation of the AMB dynamic model into a new class of uncertain system shows that this gyroscopic effect lies in the mismatched part of the system matrix. Moreover, the current gain parameter is allowed to be varied in a known bound as an uncertainty in the input matrix. SMC design method is proposed in which the sufficient condition that guarantees the global exponential stability of the reduced-order system is represented in Linear Matrix Inequality (LMI). Then, a new chattering-free control law is established such that the system states are driven to reach the switching surface and stay on it thereafter. The performance of the controller applied to the AMB model is demonstrated through simulation works under various system conditions.
Abstract: In this paper, Speed Sensorless Indirect Field Oriented Control (IFOC) of a Permanent Magnet Synchronous machine (PMSM) is studied. The closed loop scheme of the drive system utilizes fuzzy speed and current controllers. Due to the well known drawbacks of the speed sensor, an algorithm is proposed in this paper to eliminate it. In fact, based on the model of the PMSM, the stator currents and rotor speed are estimated simultaneously using adaptive Luenberger observer for currents and MRAS (Model Reference Adaptive System) observer for rotor speed. To overcome the sensivity of this algorithm against parameter variation, adaptive for on line stator resistance tuning is proposed. The validity of the proposed method is verified by an extensive simulation work.
Abstract: Doubly fed induction machines DFIM are used
mainly for wind energy conversion in MW power plants. This paper
presents a new strategy of field oriented control ,it is based on the
principle of a double flux orientation of stator and rotor at the same
time. Therefore, the orthogonality created between the two oriented
fluxes, which must be strictly observed, leads to generate a linear and
decoupled control with an optimal torque. The obtained simulation
results show the feasibility and the effectiveness of the suggested
method.
Abstract: In this paper presents a technique for developing the
computational efficiency in simulating double output induction
generators (DOIG) with two rotor circuits where stator transients are
to be included. Iterative decomposition is used to separate the flux–
Linkage equations into decoupled fast and slow subsystems, after
which the model order of the fast subsystems is reduced by
neglecting the heavily damped fast transients caused by the second
rotor circuit using integral manifolds theory. The two decoupled
subsystems along with the equation for the very slowly changing slip
constitute a three time-scale model for the machine which resulted in
increasing computational speed. Finally, the proposed method of
reduced order in this paper is compared with the other conventional
methods in linear and nonlinear modes and it is shown that this
method is better than the other methods regarding simulation
accuracy and speed.