Abstract: This paper describes simple implementation of
homotopy (also called continuation) algorithm for determining the proper resistance of the resistor to dissipate energy at a specified rate of an electric circuit. Homotopy algorithm can be considered as a developing of the classical methods in numerical computing such as Newton-Raphson and fixed
point methods. In homoptopy methods, an embedding
parameter is used to control the convergence. The method purposed in this work utilizes a special homotopy called Newton homotopy. Numerical example solved in MATLAB is given to show the effectiveness of the purposed method
Abstract: In this study, workplace environmental monitoring
systems were established using USN(Ubiquitous Sensor Networks)
and LabVIEW. Although existing direct sampling methods enable
finding accurate values as of the time points of measurement, those
methods are disadvantageous in that continuous management and
supervision are difficult and costs for are high when those methods are
used. Therefore, the efficiency and reliability of workplace
management by supervisors are relatively low when those methods are
used. In this study, systems were established so that information on
workplace environmental factors such as temperatures, humidity and
noises is measured and transmitted to the PC in real time to enable
supervisors to monitor workplaces through LabVIEW on the PC.
When any accidents have occurred in workplaces, supervisors can
immediately respond through the monitoring system and this system
enables integrated workplace management and the prevention of
safety accidents. By introducing these monitoring systems, safety
accidents due to harmful environmental factors in workplaces can be
prevented and these monitoring systems will be also helpful in finding
out the correlation between safety accidents and occupational diseases
by comparing and linking databases established by this monitoring
system with existing statistical data.
Abstract: E-Appointment Scheduling (EAS) has been developed
to handle appointment for UMP students, lecturers in Faculty of
Computer Systems & Software Engineering (FCSSE) and Student
Medical Center. The schedules are based on the timetable and
university activities. Constraints Logic Programming (CLP) has been
implemented to solve the scheduling problems by giving
recommendation to the users in part of determining any available
slots from the lecturers and doctors- timetable. By using this system,
we can avoid wasting time and cost because this application will set
an appointment by auto-generated. In addition, this system can be an
alternative to the lecturers and doctors to make decisions whether to
approve or reject the appointments.
Abstract: In this study, the existence and uniqueness of the solution of a nonlinear singular integral equation that is defined on a region in the complex plane is proven and a method is given for finding the solution.
Abstract: This paper presents a new approach for image
segmentation by applying Pillar-Kmeans algorithm. This
segmentation process includes a new mechanism for clustering the
elements of high-resolution images in order to improve precision and
reduce computation time. The system applies K-means clustering to
the image segmentation after optimized by Pillar Algorithm. The
Pillar algorithm considers the pillars- placement which should be
located as far as possible from each other to withstand against the
pressure distribution of a roof, as identical to the number of centroids
amongst the data distribution. This algorithm is able to optimize the
K-means clustering for image segmentation in aspects of precision
and computation time. It designates the initial centroids- positions
by calculating the accumulated distance metric between each data
point and all previous centroids, and then selects data points which
have the maximum distance as new initial centroids. This algorithm
distributes all initial centroids according to the maximum
accumulated distance metric. This paper evaluates the proposed
approach for image segmentation by comparing with K-means and
Gaussian Mixture Model algorithm and involving RGB, HSV, HSL
and CIELAB color spaces. The experimental results clarify the
effectiveness of our approach to improve the segmentation quality in
aspects of precision and computational time.
Abstract: A concrete structure is designed and constructed for its
purpose of use, and is expected to maintain its function for the target
durable years from when it was planned. Nevertheless, as time elapses
the structure gradually deteriorates and then eventually degrades to the
point where the structure cannot exert the function for which it was
planned. The performance of concrete that is able to maintain the level
of the performance required over the designed period of use as it has
less deterioration caused by the elapse of time under the designed
condition is referred to as Durability. There are a number of causes of
durability degradation, but especially chloride damage, carbonation,
freeze-thaw, etc are the main causes. In this study, carbonation, one of
the main causes of deterioration of the durability of a concrete
structure, was investigated via a microstructure analysis technique.
The method for the measurement of carbonation was studied using the
existing indicator method, and the method of measuring the progress
of carbonation in a quantitative manner was simultaneously studied
using a FT-IR (Fourier-Transform Infrared) Spectrometer along with
the microstructure analysis technique.
Abstract: The stochastic nature of tool life using conventional discrete-wear data from experimental tests usually exists due to many individual and interacting parameters. It is a common practice in batch production to continually use the same tool to machine different parts, using disparate machining parameters. In such an environment, the optimal points at which tools have to be changed, while achieving minimum production cost and maximum production rate within the surface roughness specifications, have not been adequately studied. In the current study, two relevant aspects are investigated using coated and uncoated inserts in turning operations: (i) the accuracy of using machinability information, from fixed parameters testing procedures, when variable parameters situations are emerged, and (ii) the credibility of tool life machinability data from prior discrete testing procedures in a non-stop machining. A novel technique is proposed and verified to normalize the conventional fixed parameters machinability data to suit the cases when parameters have to be changed for the same tool. Also, an experimental investigation has been established to evaluate the error in the tool life assessment when machinability from discrete testing procedures is employed in uninterrupted practical machining.
Abstract: The paper presents a compressor anti-surge control
system, that results in maximizing compressor throughput with
pressure standard deviation reduction, increased safety margin
between design point and surge limit line and avoiding possible
machine surge. Alternative control strategies are presented.
Abstract: The paper presents a technique suitable in robot
vision applications where it is not possible to establish the object position from one view. Usually, one view pose calculation methods
are based on the correspondence of image features established at a
training step and exactly the same image features extracted at the
execution step, for a different object pose. When such a
correspondence is not feasible because of the lack of specific features
a new method is proposed. In the first step the method computes
from two views the 3D pose of feature points. Subsequently, using a
registration algorithm, the set of 3D feature points extracted at the execution phase is aligned with the set of 3D feature points extracted
at the training phase. The result is a Euclidean transform which have
to be used by robot head for reorientation at execution step.
Abstract: Interest in Human Consciousness has been revived in the late 20th century from different scientific disciplines. Consciousness studies involve both its understanding and its application. In this paper, a computational model of the minimum consciousness functions necessary in my point of view for Artificial Intelligence applications is presented with the aim of improving the way computations will be made in the future. In section I, human consciousness is briefly described according to the scope of this paper. In section II, a minimum set of consciousness functions is defined - based on the literature reviewed - to be modelled, and then a computational model of these functions is presented in section III. In section IV, an analysis of the model is carried out to describe its functioning in detail.
Abstract: For this study, this researcher conducted a precision
network adjustment with QOCA, the precision network adjustment
software developed by Jet Propulsion Laboratory, to perform an
integrated network adjustment on the Unified Control Points managed
by the National Geographic Information Institute. Towards this end,
275 Unified Control Points observed in 2008 were selected before a
network adjustment is performed on those 275 Unified Control Points.
The RMSE on the discrepancies of coordinates as compared to the
results of GLOBK was ±6.07mm along the N axis, ±2.68mm along the
E axis and ±6.49mm along the U axis.
Abstract: Enhancement of the performance of a reverse osmosis
(RO) unit through periodic control is studied. The periodic control
manipulates the feed pressure and flow rate of the RO unit. To ensure
the periodic behavior of the inputs, the manipulated variables (MV)
are transformed into the form of sinusoidal functions. In this case, the
amplitude and period of the sinusoidal functions become the
surrogate MV and are thus regulated via nonlinear model predictive
control algorithm. The simulation results indicated that the control
system can generate cyclic inputs necessary to enhance the closedloop
performance in the sense of increasing the permeate production
and lowering the salt concentration. The proposed control system can
attain its objective with arbitrary set point for the controlled outputs.
Successful results were also obtained in the presence of modeling
errors.
Abstract: Due to the non-linear characteristics of photovoltaic
(PV) array, PV systems typically are equipped with the capability of
maximum power point tracking (MPPT) feature. Moreover, in the
case of PV array under partially shaded conditions, hotspot problem
will occur which could damage the PV cells. Partial shading causes
multiple peaks in the P-V characteristic curves. This paper presents a
hybrid algorithm of Particle Swarm Optimization (PSO) and
Artificial Neural Network (ANN) MPPT algorithm for the detection
of global peak among the multiple peaks in order to extract the true
maximum energy from PV panel. The PV system consists of PV
array, dc-dc boost converter controlled by the proposed MPPT
algorithm and a resistive load. The system was simulated using
MATLAB/Simulink package. The simulation results show that the
proposed algorithm performs well to detect the true global peak
power. The results of the simulations are analyzed and discussed.
Abstract: The paper proposes a way of parallel processing of
SURF and Optical Flow for moving object recognition and tracking.
The object recognition and tracking is one of the most important task
in computer vision, however disadvantage are many operations cause
processing speed slower so that it can-t do real-time object recognition
and tracking. The proposed method uses a typical way of feature
extraction SURF and moving object Optical Flow for reduce
disadvantage and real-time moving object recognition and tracking,
and parallel processing techniques for speed improvement. First
analyse that an image from DB and acquired through the camera using
SURF for compared to the same object recognition then set ROI
(Region of Interest) for tracking movement of feature points using
Optical Flow. Secondly, using Multi-Thread is for improved
processing speed and recognition by parallel processing. Finally,
performance is evaluated and verified efficiency of algorithm
throughout the experiment.
Abstract: The Korean government has applied preliminary feasibility study for new and huge R&D programs since 2008.The study is carried out from the viewpoints of technology, policy, and Economics. Then integrate the separate analysis and finally arrive at a definite result; whether a program is feasible or unfeasible, This paper describes the concept and method of the feasibility analysis focused on technological viability assessment for technical analysis. It consists of technology trend assessment and technology level assessment. Through the analysis, we can determine the chance of schedule delay or cost overrun occurring in the proposed plan.
Abstract: A research program is conducted to evaluate the
mechanical properties of Ultra High Performance Concrete, target
compressive strength at the age of 28 days being more than 150 MPa.
The methodology to develop such mix has been explained. The
material properties, mix design and curing regime are determined.
The material attributes are understood by studying the stress strain
behaviour of UHPC cylinders under uniaxial compressive loading.
The load –crack mouth opening displacement (cmod) of UHPC
beams, flexural strength and fracture energy was evaluated using
third point loading test. Compressive strength and Split tensile
strength results are determined to find out the compressive and tensile
behaviour. Residual strength parameters are presented vividly
explaining the flexural performance, toughness of concrete.Durability
studies were also done to compare the effect of fibre to that of a
control mix For all the studies the Mechanical properties were
evaluated by varying the percentage and aspect ratio of steel fibres
The results reflected that higher aspect ratio and fibre volume
produced drastic changes in the cube strength, cylinder strength, post
peak response, load-cmod, fracture energy flexural strength, split
tensile strength, residual strength and durability. In regards to null
application of UHPC in India, an initiative is undertaken to
comprehend the mechanical behaviour of UHPC, which will be vital
for longer run in commercialization for structural applications.
Abstract: Fracture process in mechanically loaded steel fiber
reinforced high-strength (SFRHSC) concrete is characterized by
fibers bridging the crack providing resistance to its opening.
Structural SFRHSC fracture model was created; material fracture
process was modeled, based on single fiber pull-out laws, which were
determined experimentally (for straight fibers, fibers with end hooks
(Dramix), and corrugated fibers (Tabix)) as well as obtained
numerically ( using FEM simulations). For this purpose experimental
program was realized and pull-out force versus pull-out fiber length
was obtained (for fibers embedded into concrete at different depth
and under different angle). Model predictions were validated by
15x15x60cm prisms 4 point bending tests. Fracture surfaces analysis
was realized for broken prisms with the goal to improve elaborated
model assumptions. Optimal SFRHSC structures were recognized.
Abstract: Internet security attack could endanger the privacy of
World Wide Web users and the integrity of their data. The attack can
be carried out on today's most secure systems- browsers, including
Netscape Navigator and Microsoft Internet Explorer. There are too
many types, methods and mechanisms of attack where new attack
techniques and exploits are constantly being developed and
discovered. In this paper, various types of internet security attack
mechanisms are explored and it is pointed out that when different
types of attacks are combined together, network security can suffer
disastrous consequences.
Abstract: The study explored varied types of human smiles and
extracted most of the key factors affecting the smiles. These key
factors then were converted into a set of control points which could
serve to satisfy the needs for creation of facial expression for 3D
animators and be further applied to the face simulation for robots in the
future. First, hundreds of human smile pictures were collected and
analyzed to identify the key factors for face expression. Then, the
factors were converted into a set of control points and sizing
parameters calculated proportionally. Finally, two different faces
were constructed for validating the parameters via the process of
simulating smiles of the same type as the original one.
Abstract: Weblog is an Internet tool that is believed to possess
great potential to facilitate learning in education. This study wants to
know if weblog can be used to promote students- critical thinking. It
used a group of secondary two students from a Singapore school to
write weblogs as a means of substitution for their traditional
handwritten assignments. The topics for the weblogging are taken
from History syllabus but modified to suit the purpose of this study.
Weblogs from the students were collected and analysed using a
known coding system for measuring critical thinking. Results show
that the topic for blogging is crucial in determining the types of
critical thinking employed by the students. Students are seen to
display critical thinking traits in the areas of information sourcing,
linking information to arguments and viewpoints justification.
Students- criticalness is more profound when the information for
writing a topic is readily available. Otherwise, they tend to be less
critical and subjective. The study also found that students lack the
ability to source for external information suggesting that students
may need to be taught information literacy in order to widen their use
of critical thinking skills.