Abstract: Solutions for the temperature profile around a moving
heat source are obtained using both analytic and finite element
(FEM) methods. Analytic and FEM solutions are applied to study the
temperature profile in welding. A moving heat source is represented
using both point heat source and uniform distributed disc heat source
models. Analytic solutions are obtained by solving the partial
differential equation for energy conservation in a solid, and FEM
results are provided by simulating welding using the ANSYS
software. Comparison is made for quasi steady state conditions. The
results provided by the analytic solutions are in good agreement with
results obtained by FEM.
Abstract: The main aim of this paper is to investigate the exponential stability of the Euler method for a stochastic age-dependent population equations with Poisson random measures. It is proved that the Euler scheme is exponentially stable in mean square sense. An example is given for illustration.
Abstract: In this work, study the location of interface in a stirred vessel with Rushton impeller by computational fluid dynamic was presented. To modeling rotating the impeller, sliding mesh (SM) technique was used and standard k-ε model was selected for turbulence closure. Mean tangential, radial and axial velocities and also turbulent kinetic energy (k) and turbulent dissipation rate (ε) in various points of tank was investigated. Results show sensitivity of system to location of interface and radius of 7 to 10cm for interface in the vessel with existence characteristics cause to increase the accuracy of simulation.
Abstract: Wind turbines with double output induction
generators can operate at variable speed permitting conversion
efficiency maximization over a wide range of wind velocities. This
paper presents the performance analysis of a wind driven double
output induction generator (DOIG) operating at varying shafts speed.
A periodic transient state analysis of DOIG equipped with two
converters is carried out using a hybrid induction machine model.
This paper simulates the harmonic content of waveforms in various
points of drive at different speeds, based on the hybrid model
(dqabc). Then the sinusoidal and trapezoidal pulse-width–modulation
control techniques are used in order to improve the power factor of
the machine and to weaken the injected low order harmonics to the
supply. Based on the frequency spectrum, total harmonics distortion,
distortion factor and power factor. Finally advantages of sinusoidal
and trapezoidal pulse width modulation techniques are compared.
Abstract: This study aims to clarify constructions which enable to improve socio-cultural values of environments and also to obtain new knowledge on selecting development plans. CVM is adopted as a method of evaluation. As a case of the research, university campus (CP; the following) is selected on account of its various environments, institutions and many users. Investigations were conducted from 4 points of view, total value and utility value of whole CP environments, values of each environment existing in CP or development plan assumed in CP. Furthermore, respondents- attributes were also investigated. In consequence, the following is obtained. 1) Almost all of total value of CP is composed of utility value of direct use. 2) Each of environment and development plans whose value is the highest is clarified. 3) Moreover, development plan to improve environmental value the most is specified.
Abstract: The shortest path (SP) problem concerns with finding the shortest path from a specific origin to a specified destination in a given network while minimizing the total cost associated with the path. This problem has widespread applications. Important applications of the SP problem include vehicle routing in transportation systems particularly in the field of in-vehicle Route Guidance System (RGS) and traffic assignment problem (in transportation planning). Well known applications of evolutionary methods like Genetic Algorithms (GA), Ant Colony Optimization, Particle Swarm Optimization (PSO) have come up to solve complex optimization problems to overcome the shortcomings of existing shortest path analysis methods. It has been reported by various researchers that PSO performs better than other evolutionary optimization algorithms in terms of success rate and solution quality. Further Geographic Information Systems (GIS) have emerged as key information systems for geospatial data analysis and visualization. This research paper is focused towards the application of PSO for solving the shortest path problem between multiple points of interest (POI) based on spatial data of Allahabad City and traffic speed data collected using GPS. Geovisualization of results of analysis is carried out in GIS.
Abstract: Software developed for a specific customer under contract
typically undergoes a period of testing by the customer before
acceptance. This is known as user acceptance testing and the process
can reveal both defects in the system and requests for changes to
the product. This paper uses nonhomogeneous Poisson processes to
model a real user acceptance data set from a recently developed
system. In particular a split Poisson process is shown to provide an
excellent fit to the data. The paper explains how this model can be
used to aid the allocation of resources through the accurate prediction
of occurrences both during the acceptance testing phase and before
this activity begins.
Abstract: In this paper, we study the existence of solution of
the four-point boundary value problem for second-order differential
equations with impulses by using leray-Schauder theory:
Abstract: Concrete performance is strongly affected by the
particle packing degree since it determines the distribution of the
cementitious component and the interaction of mineral particles. By
using packing theory designers will be able to select optimal
aggregate materials for preparing concrete with low cement content,
which is beneficial from the point of cost. Optimum particle packing
implies minimizing porosity and thereby reducing the amount of
cement paste needed to fill the voids between the aggregate particles,
taking also the rheology of the concrete into consideration. For
reaching good fluidity superplasticizers are required. The results from
pilot tests at Luleå University of Technology (LTU) show various
forms of the proposed theoretical models, and the empirical approach
taken in the study seems to provide a safer basis for developing new,
improved packing models.
Abstract: In this work study the location of interface in a stirred vessel with a Concave impeller by computational fluid dynamic was presented. To modeling rotating the impeller, sliding mesh (SM) technique was used and standard k-ε model was selected for turbulence closure. Mean tangential, radial and axial velocities and also turbulent kinetic energy (k) and turbulent dissipation rate (ε) in various points of tank was investigated. Results show sensitivity of system to location of interface and radius of 7 to 10cm for interface in the vessel with existence characteristics cause to increase the accuracy of simulation.
Abstract: Image Searching was always a problem specially when these images are not properly managed or these are distributed over different locations. Currently different techniques are used for image search. On one end, more features of the image are captured and stored to get better results. Storing and management of such features is itself a time consuming job. While on the other extreme if fewer features are stored the accuracy rate is not satisfactory. Same image stored with different visual properties can further reduce the rate of accuracy. In this paper we present a new concept of using polynomials of sorted histogram of the image. This approach need less overhead and can cope with the difference in visual features of image.
Abstract: This paper presents a hybrid fuzzy-PD plus PID
(HFPP) controller and its application to steam distillation process for
essential oil extraction system. Steam temperature is one of the most
significant parameters that can influence the composition of essential
oil yield. Due to parameter variations and changes in operation
conditions during distillation, a robust steam temperature controller becomes nontrivial to avoid the degradation of essential oil quality.
Initially, the PRBS input is triggered to the system and output of steam temperature is modeled using ARX model structure. The
parameter estimation and tuning method is adopted by simulation
using HFPP controller scheme. The effectiveness and robustness of
proposed controller technique is validated by real time
implementation to the system. The performance of HFPP using 25 and 49 fuzzy rules is compared. The experimental result demonstrates the proposed HFPP using 49 fuzzy rules achieves a
better, consistent and robust controller compared to PID when considering the test on tracking the set point and the effects due to disturbance.
Abstract: Exclusive breastfeeding is the feeding of a baby on no other milk apart from breast milk. Exclusive breastfeeding during the first 6 months of life is of fundamental importance because it supports optimal growth and development during infancy and reduces the risk of obliterating diseases and problems. Moreover, in developed countries, exclusive breastfeeding has decreased the incidence and/or severity of diarrhea, lower respiratory infection and urinary tract infection. In this paper, we study the factors that influence exclusive breastfeeding and use the Generalized Poisson regression model to analyze the practices of exclusive breastfeeding in Mauritius. We develop two sets of quasi-likelihood equations (QLE)to estimate the parameters.
Abstract: This paper discuss the separation of the miscible
liquids by means of fractional distillation. For complete separation of
liquids, the process of heating, condensation, separation and storage
is done automatically to achieve the objective. PIC micro-controller
has been used to control each and every process of the work. The
controller also controls the storage process by activating and deactivating
the conveyors. The liquids are heated which on reaching
their respective boiling points evaporate and enter the condensation
chamber where they convert into liquid. The liquids are then directed
to their respective tanks by means of stepper motor which moves in
three directions, each movement into different tank. The tank on
filling sends the signal to controller which then opens the solenoid
valves. The tank is emptied into the beakers below the nozzle. As the
beaker filled, the nozzle closes and the conveyors come into
operation. The filled beaker is replaced by an empty beaker from
behind. The work can be used in oil industries, chemical industries
and paint industries.
Abstract: Dengue disease is an infectious vector-borne viral
disease that is commonly found in tropical and sub-tropical regions,
especially in urban and semi-urban areas, around the world and
including Malaysia. There is no currently available vaccine or
chemotherapy for the prevention or treatment of dengue disease.
Therefore prevention and treatment of the disease depend on vector
surveillance and control measures. Disease risk mapping has been
recognized as an important tool in the prevention and control
strategies for diseases. The choice of statistical model used for
relative risk estimation is important as a good model will
subsequently produce a good disease risk map. Therefore, the aim of
this study is to estimate the relative risk for dengue disease based
initially on the most common statistic used in disease mapping called
Standardized Morbidity Ratio (SMR) and one of the earliest
applications of Bayesian methodology called Poisson-gamma model.
This paper begins by providing a review of the SMR method, which
we then apply to dengue data of Perak, Malaysia. We then fit an
extension of the SMR method, which is the Poisson-gamma model.
Both results are displayed and compared using graph, tables and
maps. Results of the analysis shows that the latter method gives a
better relative risk estimates compared with using the SMR. The
Poisson-gamma model has been demonstrated can overcome the
problem of SMR when there is no observed dengue cases in certain
regions. However, covariate adjustment in this model is difficult and
there is no possibility for allowing spatial correlation between risks in
adjacent areas. The drawbacks of this model have motivated many
researchers to propose other alternative methods for estimating the
risk.
Abstract: Let p be a prime number, Fp be a finite field, and let k ∈ F*p. In this paper, we consider the number of rational points onconics Cp,k: x2 − ky2 = 1 over Fp. We proved that the order of Cp,k over Fp is p-1 if k is a quadratic residue mod p and is p + 1 if k is not a quadratic residue mod p. Later we derive some resultsconcerning the sums ΣC[x]p,k(Fp) and ΣC[y]p,k(Fp), the sum of x- and y-coordinates of all points (x, y) on Cp,k, respectively.
Abstract: Cameron Highlands is a mountainous area subjected
to torrential tropical showers. It extracts 5.8 million liters of water
per day for drinking supply from its rivers at several intake points.
The water quality of rivers in Cameron Highlands, however, has
deteriorated significantly due to land clearing for agriculture,
excessive usage of pesticides and fertilizers as well as construction
activities in rapidly developing urban areas. On the other hand, these
pollution sources known as non-point pollution sources are diverse
and hard to identify and therefore they are difficult to estimate.
Hence, Geographical Information Systems (GIS) was used to provide
an extensive approach to evaluate landuse and other mapping
characteristics to explain the spatial distribution of non-point sources
of contamination in Cameron Highlands. The method to assess
pollution sources has been developed by using Cameron Highlands
Master Plan (2006-2010) for integrating GIS, databases, as well as
pollution loads in the area of study. The results show highest annual
runoff is created by forest, 3.56 × 108 m3/yr followed by urban
development, 1.46 × 108 m3/yr. Furthermore, urban development
causes highest BOD load (1.31 × 106 kgBOD/yr) while agricultural
activities and forest contribute the highest annual loads for
phosphorus (6.91 × 104 kgP/yr) and nitrogen (2.50 × 105 kgN/yr),
respectively. Therefore, best management practices (BMPs) are
suggested to be applied to reduce pollution level in the area.
Abstract: An analysis is performed to study the influence of nonuniform double slot suction on a steady laminar boundary layer flow over a rotating sphere when fluid properties such as viscosity and Prandtl number are inverse linear functions of temperature. Nonsimilar solutions have been obtained from the starting point of the streamwise co-ordinate to the exact point of separation. The difficulties arising at the starting point of the streamwise co-ordinate, at the edges of the slot and at the point of separation have been overcome by applying an implicit finite difference scheme in combination with the quasi-linearization technique and an appropriate selection of the finer step sizes along the stream-wise direction. The present investigation shows that the point of ordinary separation can be delayed by nonuniform double slot suction if the mass transfer rate is increased and also if the slots are positioned further downstream. In addition, the investigation reveals that double slot suction is found to be more effective compared to a single slot suction in delaying ordinary separation. As rotation parameter increase the point of separation moves upstream direction.
Abstract: A numerical simulation of micro Poiseuille flow has
performed for rarefied and compressible flow at slip flow regimes.
The wall roughness is simulated in two cases with triangular
microelements and random micro peaks distributed on wall surfaces
to study the effects of roughness shape and distribution on flow field.
Two values of Mach and Knudsen numbers have used to investigate
the effects of rarefaction as well as compressibility. The numerical
results have also checked with available theoretical and experimental
relations and good agreements has achieved. High influence of
roughness shape can be seen for both compressible and
incompressible rarefied flows. In addition it is found that rarefaction
has more significant effect on flow field in microchannels with
higher relative roughness. It is also found that compressibility has
more significant effects on Poiseuille number when relative
roughness increases.
Abstract: In this paper, we have proposed a Haar wavelet quasilinearization
method to solve the well known Blasius equation. The
method is based on the uniform Haar wavelet operational matrix
defined over the interval [0, 1]. In this method, we have proposed the
transformation for converting the problem on a fixed computational
domain. The Blasius equation arises in the various boundary layer
problems of hydrodynamics and in fluid mechanics of laminar
viscous flows. Quasi-linearization is iterative process but our
proposed technique gives excellent numerical results with quasilinearization
for solving nonlinear differential equations without any
iteration on selecting collocation points by Haar wavelets. We have
solved Blasius equation for 1≤α ≤ 2 and the numerical results are
compared with the available results in literature. Finally, we
conclude that proposed method is a promising tool for solving the
well known nonlinear Blasius equation.