Abstract: Thermal water hammer is a special type of water
hammer which rarely occurs in heat exchangers. In biphasic fluids, if
steam bubbles are surrounded by condensate, regarding lower
condensate temperature than steam, they will suddenly collapse. As a
result, the vacuum caused by an extreme change in volume lead to
movement of the condensates in all directions and their collision the
force produced by this collision leads to a severe stress in the pipe
wall. This phenomenon is a special type of water hammer. According
to fluid mechanics, this phenomenon is a particular type of transient
flows during which abrupt change of fluid leads to sudden pressure
change inside the tube. In this paper, the mechanism of abrupt failure
of 80 tubes of 481 tubes of a methanol heat exchanger is discussed.
Initially, due to excessive temperature differences between heat
transfer fluids and simultaneous failure of 80 tubes, thermal shock
was presupposed as the reason of failure. Deeper investigation on
cross-section of failed tubes showed that failure was, ductile type of
failure, so the first hypothesis was rejected. Further analysis and more
accurate experiments revealed that failure of tubes caused by thermal
water hammer. Finally, the causes of thermal water hammer and
various solutions to avoid such mechanism are discussed.
Abstract: The essential oil of M. × piperita L. was formulated
into a topical gel. The prepared gel was characterized for its pH,
viscosity, spreadiblity, consistency and extrudiblity, while its stability
was evaluated under different temperature conditions. The prepared
M. × piperita oil gel was clear and transparent. The pH value of
developed gel was 6.6, while its viscosity was 1200 cP. Spreadability
and consistency of the M. × piperita oil gel was 10.7 g.cm/sec and 7
mm, respectively. The prepared gel showed good extrudiblity. During
the stability studies, no significant change in pH and viscosity as a
function of time for gel was observed, indicating stability of prepared
formulation. The gel developed in this study is expected to forward
the usage of M. × piperita essential towards commercial application.
Abstract: In textile industry, besides the conventional textile
products, technical textile goods, that have been brought external
functional properties into, are being developed for technical textile
industry. Especially these products produced with weaving
technology are widely preferred in areas such as sports, geology,
medical, automotive, construction and marine sectors. These textile
products are exposed to various stresses and large deformations under
typical conditions of use. At this point, sufficient and reliable data
could not be obtained with uniaxial tensile tests for determination of
the mechanical properties of such products due to mainly biaxial
stress state. Therefore, the most preferred method is a biaxial tensile
test method and analysis. These tests and analysis is applied to fabrics
with different functional features in order to establish the textile
material with several characteristics and mechanical properties of the
product. Planar biaxial tensile test, cylindrical inflation and bulge
tests are generally required to apply for textile products that are used
in automotive, sailing and sports areas and construction industry to
minimize accidents as long as their service life. Airbags, seat belts
and car tires in the automotive sector are also subject to the same
biaxial stress states, and can be characterized by same types of
experiments. In this study, in accordance with the research literature
related to the various biaxial test methods are compared. Results with
discussions are elaborated mainly focusing on the design of a biaxial
test apparatus to obtain applicable experimental data for developing a
finite element model. Sample experimental results on a prototype
system are expressed.
Abstract: The effects of upflow liquid velocity (ULV) on
performance of expanded granular sludge bed (EGSB) system were
investigated. The EGSB reactor, made from galvanized steel pipe
0.10 m diameter and 5 m height, had been used to treat piggery
wastewater, after passing through acidification tank. It consisted of
39.3 l working volume in reaction zone and 122 l working volume in
sedimentation zone, at the upper part. The reactor was seeded with
anaerobically digested sludge and operated at the ULVs of 4, 8, 12
and 16 m/h, consecutively, corresponding to organic loading rates of
9.6 – 13.0 kg COD/ (m3.d). The average COD concentrations in the
influent were 9,601 – 13,050 mg/l. The COD removal was not
significantly different, i.e. 93.0% - 94.0%, except at ULV 12 m/h where
SS in the influent was exceptionally high so that VSS washout had
occurred, leading to low COD removal. The FCOD and VFA
concentrations in the effluent of all experiments were not much
different, indicating the same range of treatment performance. The
biogas production decreased at higher ULV and ULV of 4 m/h is
suggested as design criterion for EGSB system.
Abstract: This paper presents a new type of mechanism and trajectory planning strategy for bipedal walking robot. The newly designed mechanism is able to improve the performance of bipedal walking robot in terms of energy efficiency and weight reduction by utilizing minimum number of actuators. The usage of parallelogram mechanism eliminates the needs of having an extra actuator at the knee joint. This mechanism works together with the joint space trajectory planning in order to realize straight legged walking which cannot be achieved by conventional inverse kinematics trajectory planning due to the singularity. The effectiveness of the proposed strategy is confirmed by computer simulation results.
Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: In the semiconductor manufacturing process, large
amounts of data are collected from various sensors of multiple
facilities. The collected data from sensors have several different characteristics
due to variables such as types of products, former processes
and recipes. In general, Statistical Quality Control (SQC) methods
assume the normality of the data to detect out-of-control states of
processes. Although the collected data have different characteristics,
using the data as inputs of SQC will increase variations of data,
require wide control limits, and decrease performance to detect outof-
control. Therefore, it is necessary to separate similar data groups
from mixed data for more accurate process control. In the paper,
we propose a regression tree using split algorithm based on Pearson
distribution to handle non-normal distribution in parametric method.
The regression tree finds similar properties of data from different
variables. The experiments using real semiconductor manufacturing
process data show improved performance in fault detecting ability.
Abstract: Radial flow reactor was focused for large scale
methanol synthesis and in which the heat transfer type was cross-flow.
The effects of operating conditions including the reactor inlet air
temperature, the heating pipe temperature and the air flow rate on the
cross-flow heat transfer was investigated and the results showed that
the temperature profile of the area in front of the heating pipe was
slightly affected by all the operating conditions. The main area whose
temperature profile was influenced was the area behind the heating
pipe. The heat transfer direction according to the air flow directions. In
order to provide the basis for radial flow reactor design calculation, the
dimensionless number group method was used for data fitting of the
bed effective thermal conductivity and the wall heat transfer
coefficient which was calculated by the mathematical model with the
product of Reynolds number and Prandtl number. The comparison of
experimental data and calculated value showed that the calculated
value fit the experimental data very well and the formulas could be
used for reactor designing calculation.
Abstract: In a wireless communication system, a
predistorter(PD) is often employed to alleviate nonlinear distortions
due to operating a power amplifier near saturation, thereby improving
the system performance and reducing the interference to adjacent
channels. This paper presents a new adaptive polynomial digital
predistorter(DPD). The proposed DPD uses Coordinate Rotation
Digital Computing(CORDIC) processors and PD process by pipelined
architecture. It is simpler and faster than conventional adaptive
polynomial DPD. The performance of the proposed DPD is proved by
MATLAB simulation.
Abstract: In order to study pressed pile test and ultimate bearing
capacity character of large-diameter steel pipe pile, based on two high-piled wharfs of Zhanjiang Port, pressed pile test and numerical simulation of three large-diameter steel pipe piles are analyzed in this
paper. Anchored pile method is used to pressed pile test, and the
curves of Q-s and ultimate bearing capacity are attained. Then the three piles are numerically simulated by ABAQUS, and results of numerical simulation and those of field test are comparatively analyzed. The results show that settlement value of numerical
simulation is larger than that of field test in the process of loading, the difference value is widening with the increasing of load, and the
ultimate difference value of settlement is 20% to 30%.
Abstract: In the Enhanced Oil Recovery (EOR) method, use of Carbon dioxide flooding whereby CO2 is injected into an oil reservoir to increase output when extracting oil resulted significant recovery worldwide. The carbon dioxide function as a pressurizing agent when mixed into the underground crude oil will reduce its viscosity and will enable a rapid oil flow. Despite the CO2’s advantage in the oil recovery, it may result to asphaltene precipitation a problem that will cause the reduction of oil produced from oil wells. In severe cases, asphaltene precipitation can cause costly blockages in oil pipes and machinery. This paper presents reviews of several studies done on mathematical modeling of asphaltene precipitation. The synthesized result from several researches done on this topic can be used as guide in order to better understand asphaltene precipitation. Likewise, this can be used as initial reference for students, and new researchers doing study on asphaltene precipitation.
Abstract: Load forecasting has always been the essential part of
an efficient power system operation and planning. A novel approach
based on support vector machines is proposed in this paper for annual
power load forecasting. Different kernel functions are selected to
construct a combinatorial algorithm. The performance of the new
model is evaluated with a real-world dataset, and compared with two
neural networks and some traditional forecasting techniques. The
results show that the proposed method exhibits superior performance.
Abstract: Grid environments include aggregation of
geographical distributed resources. Grid is put forward in three types
of computational, data and storage. This paper presents a research on
data grid. Data grid is used for covering and securing accessibility to
data from among many heterogeneous sources. Users are not worry
on the place where data is located in it, provided that, they should get
access to the data. Metadata is used for getting access to data in data
grid. Presently, application metadata catalogue and SRB middle-ware
package are used in data grids for management of metadata. At this
paper, possibility of updating, streamlining and searching is provided
simultaneously and rapidly through classified table of preserving
metadata and conversion of each table to numerous tables.
Meanwhile, with regard to the specific application, the most
appropriate and best division is set and determined. Concurrency of
implementation of some of requests and execution of pipeline is
adaptability as a result of this technique.
Abstract: Environment-assisted cracking (EAC) is one of the most serious causes of structural failure over a broad range of industrial applications including offshore structures. In EAC condition there is not a definite relation such as Paris equation in Linear Elastic Fracture Mechanics (LEFM). According to studying and searching a lot what the researchers said either a material has contact with hydrogen or any other corrosive environment, phenomenon of electrical and chemical reactions of material with its environment will be happened. In the literature, there are many different works to consider fatigue crack growing and solve it but they are experimental works. Thus, in this paper, authors have an aim to evaluate mathematically the pervious works in LEFM. Obviously, if an environment is more sour and corrosive, the changes of stress intensity factor is more and the calculation of stress intensity factor is difficult. A mathematical relation to deal with the stress intensity factor during the diffusion of sour environment especially hydrogen in a marine pipeline is presented. By using this relation having and some experimental relation an analytical formulation will be presented which enables the fatigue crack growth and critical crack length under cyclic loading to be predicted. In addition, we can calculate KSCC and stress intensity factor in the pipeline caused by EAC.
Abstract: Stuck-pipe in drilling operations is one of the most
pressing and expensive problems in the oil industry. This paper
describes a computational simulation and an experimental study of
the hydrodynamic vibrator, which may be used for liquidation of
stuck-pipe problems during well drilling. The work principle of the
vibrator is based upon the known phenomena of Vortex Street of
Karman and the resulting generation of vibrations. We will discuss
the computational simulation and experimental investigations of
vibrations in this device. The frequency of the vibration parameters
has been measured as a function of the wide range Reynolds Number.
The validity of the computational simulation and of the assumptions
on which it is based has been proved experimentally. The
computational simulation of the vibrator work and its effectiveness
was carried out using FLUENT software. The research showed high
degree of congruence with the results of the laboratory tests and
allowed to determine the effect of the granular material features upon
the pipe vibration in the well. This study demonstrates the potential
of using the hydrodynamic vibrator in a well drilling system.