Abstract: The nature of adsorbed species on catalytic surface
over an industrial precipitated iron-based high temperature catalyst
during FTS was investigated by in-situ DRIFTS and chemical
trapping. The formulation of the mechanism of oxygenates formation
and key intermediates were also discussed. Numerous oxygenated
precursors and crucial intermediates were found by in-situ DRIFTS,
such as surface acetate, acetyl and methoxide. The results showed that
adsorbed molecules on surface such as methanol or acetaldehyde
could react with basic sites such as lattice oxygen or free surface
hydroxyls. Adsorbed molecules also had reactivity of oxidizing.
Moreover, acetyl as a key intermediate for oxygenates was observed
by investigation of CH3OH + CO and CH3I + CO + H2. Based on the
nature of surface properties, the mechanism of oxygenates formation
on precipitated iron-based high temperature catalyst was discussed.
Abstract: Effect of high temperature exposure on properties of cement mortar containing municipal solid waste incineration (MSWI) bottom ash as partial natural aggregate replacement is analyzed in the paper. The measurements of mechanical properties, bulk density, matrix density, total open porosity, sorption and desorption isotherms are done on samples exposed to the temperatures of 20°C to 1000°C. TGA analysis is performed as well. Finally, the studied samples are analyzed by IR spectroscopy in order to evaluate TGA data.
Abstract: Within this work High Temperature Single Impact
Studies were performed to evaluate deformation mechanisms at
different energy and momentum levels. To show the influence of
different microstructures and hardness levels and their response to
single impacts four different materials were tested at various
temperatures up to 700°C. One carbide reinforced NiCrBSi based
Metal Matrix Composite and three different steels were tested. The
aim of this work is to determine critical energies for fracture
appearance and the materials response at different energy and
momenta levels. Critical impact loadings were examined at elevated
temperatures to limit operating conditions in impact dominated
regimes at elevated temperatures. The investigations on the
mechanisms were performed using different means of microscopy at
the surface and in metallographic cross sections. Results indicate
temperature dependence of the occurrence of cracks in hardphase
rich materials, such as Metal Matrix Composites High Speed Steels
and the influence of different impact momenta at constant energies
on the deformation of different steels.
Abstract: Magnetic and semiconductor nanomaterials exhibit
novel magnetic and optical properties owing to their unique size and
shape-dependent effects. With shrinking the size down to nanoscale
region, various anomalous properties that normally not present in bulk
start to dominate. Ability in harnessing of these anomalous properties
for the design of various advance electronic devices is strictly
dependent on synthetic strategies. Hence, current research has focused
on developing a rational synthetic control to produce high quality
nanocrystals by using organometallic approach to tune both size and
shape of the nanomaterials. In order to elucidate the growth
mechanism, transmission electron microscopy was employed as a
powerful tool in performing real time-resolved morphologies and
structural characterization of magnetic (Fe3O4) and semiconductor
(ZnO) nanocrystals. The current synthetic approach is found able to
produce nanostructures with well-defined shapes. We have found that
oleic acid is an effective capping ligand in preparing oxide-based
nanostructures without any agglomerations, even at high temperature.
The oleate-based precursors and capping ligands are fatty acid
compounds, which are respectively originated from natural palm oil
with low toxicity. In comparison with other synthetic approaches in
producing nanostructures, current synthetic method offers an effective
route to produce oxide-based nanomaterials with well-defined shapes
and good monodispersity. The nanocystals are well-separated with
each other without any stacking effect. In addition, the as-synthesized
nanopellets are stable in terms of chemically and physically if
compared to those nanomaterials that are previous reported. Further
development and extension of current synthetic strategy are being
pursued to combine both of these materials into nanocomposite form
that will be used as “smart magnetic nanophotocatalyst" for industry
waste water treatment.
Abstract: The study of effect of laser scanning speed on
material efficiency in Ti6Al4V application is very important because unspent powder is not reusable because of high temperature oxygen
pick-up and contamination. This study carried out an extensive study
on the effect of scanning speed on material efficiency by varying the
speed between 0.01 to 0.1m/sec. The samples are wire brushed and
cleaned with acetone after each deposition to remove un-melted
particles from the surface of the deposit. The substrate is weighed before and after deposition. A formula was developed to calculate the
material efficiency and the scanning speed was compared with the
powder efficiency obtained. The results are presented and discussed.
The study revealed that the optimum scanning speed exists for this study at 0.01m/sec, above and below which the powder efficiency
will drop
Abstract: A good green building design project, designers should consider not only energy consumption, but also healthy and comfortable needs of inhabitants. In recent years, the Taiwan government paid attentions on both carbon reduction and indoor air quality issues, which be presented in the legislation of Building Codes and other regulations. Taiwan located in hot and humid climates, dampness in buildings leads to significant microbial pollution and building damage. This means that the high temperature and humidity present a serious indoor air quality issue. The interactions between vapor transfers and energy fluxes are essential for the whole building Heat Air and Moisture (HAM) response. However, a simulation tool with short calculation time, property accuracy and interface is needed for practical building design processes. In this research, we consider the vapor transfer phenomenon of building materials as well as temperature and humidity and energy consumption in a building space. The simulation bases on the EMPD method, which was performed by EnergyPlus, a simulation tool developed by DOE, to simulate the indoor moisture variation in a one-zone residential unit based on the Effective Moisture Penetration Depth Method, which is more suitable for practical building design processes.
Abstract: A group of Stellite alloys are studied in consideration
of temperature effects on their hardness and wear resistance. The
hardness test is conducted on a micro-hardness tester with a hot stage
equipped that allows heating the specimen up to 650°C. The wear
resistance of each alloy is evaluated using a pin-on-disc tribometer
with a heating furnace built-in that provides the temperature capacity
up to 450°C. The experimental results demonstrate that the hardness
and wear resistance of Stellite alloys behave differently at room
temperature and at high temperatures. The wear resistance of Stellite
alloys at room temperature mainly depends on their carbon content and
also influenced by the tungsten content in the alloys. However, at high
temperatures the wear mechanisms of Stellite alloys become more
complex, involving multiple factors. The relationships between
chemical composition, microstructure, hardness and wear resistance of
these alloys are studied, with focus on temperature effect on these
relations.
Abstract: In this paper, creep constitutive equations of base
(Parent) and weld materials of the weldment for cold-drawn 304L
stainless steel have been obtained experimentally. For this purpose,
test samples have been generated from cold drawn bars and weld
material according to the ASTM standard. The creep behavior and
properties have been examined for these materials by conducting uniaxial
creep tests. Constant temperatures and constant load uni-axial
creep tests have been carried out at two high temperatures, 680 and
720 oC, subjected to constant loads, which produce initial stresses
ranging from 240 to 360 MPa. The experimental data have been used
to obtain the creep constitutive parameters using numerical
optimization techniques.
Abstract: Recently, a growing interest has emerged on the
development of new and efficient energy sources, due to the inevitable extinction of the nonrenewable energy reserves. One of
these alternative sources which has a great potential and sustainability to meet up the energy demand is biomass energy. This
significant energy source can be utilized with various energy
conversion technologies, one of which is biomass gasification in
supercritical water.
Water, being the most important solvent in nature, has very important characteristics as a reaction solvent under supercritical
circumstances. At temperatures above its critical point (374.8oC and
22.1 MPa), water becomes more acidic and its diffusivity increases.
Working with water at high temperatures increases the thermal
reaction rate, which in consequence leads to a better dissolving of the
organic matters and a fast reaction with oxygen. Hence, supercritical water offers a control mechanism depending on solubility, excellent
transport properties based on its high diffusion ability and new reaction possibilities for hydrolysis or oxidation.
In this study the gasification of a real biomass, namely olive mill
wastewater (OMW), in supercritical water is investigated with the
use of Pt/Al2O3 and Ni/Al2O3 catalysts. OMW is a by-product
obtained during olive oil production, which has a complex nature
characterized by a high content of organic compounds and
polyphenols. These properties impose OMW a significant pollution
potential, but at the same time, the high content of organics makes
OMW a desirable biomass candidate for energy production.
All of the catalytic gasification experiments were made with five
different reaction temperatures (400, 450, 500, 550 and 600°C),
under a constant pressure of 25 MPa. For the experiments conducted
with Ni/Al2O3 catalyst, the effect of five reaction times (30, 60, 90,
120 and 150 s) was investigated. However, procuring that similar
gasification efficiencies could be obtained at shorter times, the experiments were made by using different reaction times (10, 15, 20,
25 and 30 s) for the case of Pt/Al2O3 catalyst. Through these experiments, the effects of temperature, time and catalyst type on the
gasification yields and treatment efficiencies were investigated.
Abstract: In this paper are illustrated the principal aspects
connected with the numerical evaluation of thermal stress induced by high gradient temperature in the concrete beam. The reinforced concrete beam has many advantages over steel
beam, such as high resistance to high temperature, high resistance to thermal shock, Better resistance to fatigue and buckling, strong
resistance against, fire, explosion, etc.
The main drawback of the reinforced concrete beam is its poor resistance to tensile stresses. In order to investigate the thermal
induced tensile stresses, a numerical model of a transient thermal
analysis is presented for the evaluation of thermo-mechanical
response of concrete beam to the high temperature, taking into account the temperature dependence of the thermo physical properties of the concrete like thermal conductivity and specific heat.
Abstract: In this paper the combination of thermal oxidation and
electrochemical anodizing processes is used to produce titanium
oxide layers. The response of titanium alloy Ti6Al4V to oxidation
processes at various temperatures and electrochemical anodizing in
various voltages are investigated. Scanning electron microscopy
(SEM); X-Ray Diffraction (XRD) and porosity determination have
been used to characterize the oxide layer thickness, surface
morphology, oxide layer-substrate adhesion and porosity. In the first
experiment, samples modified by thermal oxidation process then
followed by electrochemical anodizing. Second experiment consists
of surfaces modified by electrochemical anodizing process and then
followed by thermal oxidation. The first method shows better
properties than other one. In second experiment, Surfaces modified
were achieved by thicker and more adherent thick oxide layers on
titanium surface. The existence of an electrochemical anodized oxide
layer did not improve the adhesion of thermal oxide layer. The high
temperature, thermal formation of an oxide layer leads to a coarse
oxide grain morphology and a complete oxidative particle. In
addition, in high temperature oxidation porosity content is increased.
The oxide layer of thermal oxidation and electrochemical anodizing
processes; on Ti–6Al–4V substrate was covered with different
colored oxide layers.
Abstract: Carbon fibers are fabricated from different materials,
such as special polyacrylonitrile (PAN) fibers, rayon fibers and pitch.
Among these three groups of materials, PAN fibers are the most
widely used precursor for the manufacture of carbon fibers. The
process of fabrication carbon fibers from special PAN fibers includes
two steps; oxidative stabilization at low temperature and
carbonization at high temperatures in an inert atmosphere. Due to the
high price of raw materials (special PAN fibers), carbon fibers are
still expensive.
In the present work the main goal is making carbon fibers from
low price commercial PAN fibers with modified chemical
compositions. The results show that in case of conducting completes
stabilization process, it is possible to produce carbon fibers with
desirable tensile strength from this type of PAN fibers. To this
matter, thermal characteristics of commercial PAN fibers were
investigated and based upon the obtained results, with some changes
in conventional procedure of stabilization in terms of temperature
and time variables; the desirable conditions of complete stabilization
is achieved.
Abstract: Several models have been introduced so far for single
electron box, SEB, which all of them were restricted to DC response
and or low temperature limit. In this paper we introduce a new time
dependent, high temperature analytical model for SEB for the first
time. DC behavior of the introduced model will be verified against
SIMON software and its time behavior will be verified against a
newly published paper regarding step response of SEB.
Abstract: The C3 plants are frequently suffering from exposure
to high temperature stress which limits the growth and yield of these
plants. This study seeks to clarify the physiological mechanisms of
heat tolerance in relation to oxidative stress in C3 species. Fifteen C3
species were exposed to prolonged moderately high temperature
stress 36/30°C for 40 days in a growth chamber. Chlorophyll
fluorescence (Fv/Fm) showed great difference among species at 40
days of the stress. The species showed decreases in Fv/Fm and
increases in malondialdehyde (MDA) content under stress condition
as well as negative correlation between Fv/Fm and MDA (r = -0.61*)
at 40 days of the stress. Hydrogen peroxide (H2O2) content before
and after stress in addition to its response under stress showed great
differences among species. The results suggest that the difference in
heat tolerance among C3 species is closely associated with the ability
to suppress oxidative damage but not with the content of reactive
oxygen species (ROS) which is regulated by complex network.
Abstract: In this study, the effect of nanofluids on the pool film
boiling was experimentally investigated at saturated condition under
atmospheric pressure. For this purpose, four different water-based
nanofluids (Al2O3, SiO2, TiO2 and CuO) with 0.1% particle volume
fraction were prepared. To investigate the boiling heat transfer, a
cylindrical rod with high temperature was used. The rod heated up to
high temperatures was immersed into nanofluids. The center
temperature of rod during the cooling process was recorded by using
a K-type thermocouple. The quenching curves showed that the pool
boiling heat transfer was strongly dependent on the nanoparticle
materials. During the repetitive quenching tests, the cooling time
decreased and thus, the film boiling vanished. Consequently, the
primary reason of this was the change of the surface characteristics
due to the nanoparticles deposition on the rod-s surface.
Abstract: The purpose of this work is fast design optimization of
the seal chamber. The study includes the mass transfer between lower
and upper chamber on seal chamber for hot water application pumps.
The use of Fluent 12.1 commercial code made it possible to capture
complex flow with heat-mass transfer, radiation, Tailor instability,
and buoyancy effect. Realizable k-epsilon model was used for
turbulence modeling. Radiation heat losses were taken into account.
The temperature distribution at seal region is predicted with respect
to heat addition.
Results show the possibilities of the model simplifications by
excluding the water domain in low chamber from calculations. CFD
simulations permit to improve seal chamber design to meet target
water temperature around the seal. This study can be used for the
analysis of different seal chamber configurations.
Abstract: Copper sulfide nanoparticles (CuS) were successfully synthesized by the pulsed plasma in liquid method, using two copper rod electrodes submerged in molten sulfur. Low electrical energy and no high temperature were applied for synthesis. Obtained CuS nanoparticles were then analyzed by means of X-ray diffraction, Low and High Resolution Transmission Electron Microscopy, Electron Diffraction, X-ray Photoelectron, Raman Spectroscopies and Field Emission Scanning Electron Microscopy. XRD analysis revealed peaks for CuS with hexagonal phase composition. TEM and HRTEM studies showed that sizes of CuS nanoparticles ranged between 10-60 nm, with the average size of about 20 nm. Copper sulfide nanoparticles have short nanorod-like structure. Raman spectroscopy found peak for CuS at 474.2cm-1of Raman region.
Abstract: In this work, we incorporated a quartic bond potential
into a coarse-grained bead-spring model to study lubricant adsorption
on a solid surface as well as depletion instability. The surface tension
density and the number density profiles were examined to verify the
solid-liquid and liquid-vapor interfaces during heat treatment. It was
found that both the liquid-vapor interfacial thickness and the
solid-vapor separation increase with the temperatureT* when T*is
below the phase transition temperature Tc
*. At high temperatures
(T*>Tc
*), the solid-vapor separation decreases gradually as the
temperature increases. In addition, we evaluated the lubricant weight
and bond loss profiles at different temperatures. It was observed that
the lubricant desorption is favored over decomposition and is the main
cause of the lubricant failure at the head disk interface in our
simulations.
Abstract: The performance of mortar subjected to high
temperature and cooled in normal ambient temperature was examined
in the laboratory to comply with the situation of burning & cooling of
a structure. Four series of cubical (5 X 5 X 5 cm) mortar specimens
were made from OPC, and partial replacement (10, 15, 20, 25 &
30%) of OPC by Rice Husk Ash (RHA) produced in the uncontrolled
environment. These specimens were heated in electric furnace to 200,
300, 400, 500 and 7000C. The specimens were kept in normal room
temperature for cooling. They were then tested for mechanical
properties and the results shows that particular 20% RHA mixed
mortar shows better fire performance.
Abstract: The power transformer is the most expensive, indispensable and arguably the most important equipment item in a power system Insulation failure in transformers can cause long term interruption to supply and loss of revenue and the condition assessment of the insulation is thus an important maintenance procedure. Oil-impregnated transformer insulation consists of mainly organic materials including mineral oil and cellulose-base paper and pressboard. The operating life of cellulose-based insulation, as with most organic insulation, depends heavily on its operating temperature rise above ambient. This paper reports results of a laboratory-based experimental investigation of partial discharge (PD) activity at high temperature in oil-impregnated insulation. The experiments reported here are part an on-going programme aimed at investigating the way in which insulation deterioration can be monitored and quantified by use of partial discharge diagnostics. Partial discharge patterns were recorded and analysed during increasing and decreasing phases of the temperature. The effect of ageing of the insulation on the PD patterns in oil and oil-impregnated insulation are also considered.