Abstract: Characterized as rich mineral substances, low
temperature, few bacteria, and stability with numerous implementation
aspects on aquaculture, food, drinking, and leisure, the deep sea water
(DSW) development has become a new industry in the world. It has
been report that marine algae contain various biologically active
compounds. This research focued on the affections in cultivating
Sagrassum cristaefolium with different concentration of deep sea
water(DSW) and surface sea water(SSW). After two and four weeks,
the total phenolic contents were compared in Sagrassum cristaefolium
culturing with different ways, and the reductive activity of them was
also be tried with potassium ferricyanide. Those fresh seaweeds were
dried with oven and were ground to powder. Progressively, the marine
algae we cultured was extracted by water under the condition with
heating them at 90Ôäâ for 1hr.The total phenolic contents were be
executed using Folin–Ciocalteu method. The results were explaining
as follows: the highest total phenolic contents and the best reductive
ability of all could be observed on the 1/4 proportion of DSW to SSW
culturing in two weeks. Furthermore, the 1/2 proportion of DSW to
SSW also showed good reductive ability and plentiful phenolic
compositions. Finally, we confirmed that difference proportion of
DSW and SSW is the major point relating to ether the total phenolic
components or the reductive ability in the Sagrassum cristaefolium. In
the future, we will use this way to mass production the marine algae or
other micro algae on industry applications.
Abstract: This paper describes the designs of a first and second
generation autonomous gas monitoring system and the successful
field trial of the final system (2nd generation). Infrared sensing
technology is used to detect and measure the greenhouse gases
methane (CH4) and carbon dioxide (CO2) at point sources. The
ability to monitor real-time events is further enhanced through the
implementation of both GSM and Bluetooth technologies to
communicate these data in real-time. These systems are robust,
reliable and a necessary tool where the monitoring of gas events in
real-time are needed.
Abstract: Supercritical carbon dioxide (SC-CO2) was used as a
solvent to extract oil from wheat bran. Extractions were carried out in a
semi-batch process at temperatures ranging from 40 to 60ºC and
pressures ranging from 10 to 30 MPa, with a carbon dioxide (CO2)
flow rate of 26.81 g/min. The oil obtained from wheat bran at different
extraction conditions was quantitatively measured to investigate the
solubility of oil in SC-CO2. The solubility of wheat bran oil was found
to be enhanced in high temperature and pressure. The composition of
fatty acids in wheat bran oil was measured by gas chromatography
(GC). Linoleic, palmitic, oleic and γ-linolenic acid were the major
fatty acids of wheat bran oil. Tocopherol contents in oil were analyzed
by high performance liquid chromatography (HPLC). The highest
amount of phenolics and tocopherols (α and β) were found at
temperature of 60ºC and pressure of 30 MPa.
Abstract: Methane is the second most important greenhouse gas
(GHG) after carbon dioxide. Amount of methane emission from
energy sector is increasing day by day with various activities. In
present work, various sources of methane emission from upstream,
middle stream and downstream of oil & gas sectors are identified and
categorised as per IPCC-2006 guidelines. Data were collected from
various oil & gas sector like (i) exploration & production of oil & gas
(ii) supply through pipelines (iii) refinery throughput & production
(iv) storage & transportation (v) usage. Methane emission factors for
various categories were determined applying Tier-II and Tier-I
approach using the collected data. Total methane emission from
Indian Oil & Gas sectors was thus estimated for the year 1990 to
2007.
Abstract: The work reported in this paper proposes
Swarm-Array computing, a novel technique inspired by swarm
robotics, and built on the foundations of autonomic and parallel
computing. The approach aims to apply autonomic computing
constructs to parallel computing systems and in effect achieve the
self-ware objectives that describe self-managing systems. The
constitution of swarm-array computing comprising four constituents,
namely the computing system, the problem/task, the swarm and the
landscape is considered. Approaches that bind these constituents
together are proposed. Space applications employing FPGAs are
identified as a potential area for applying swarm-array computing for
building reliable systems. The feasibility of a proposed approach is
validated on the SeSAm multi-agent simulator and landscapes are
generated using the MATLAB toolkit.
Abstract: The aim of this study was to synthesize the single
walled carbon nanotubes (SWCNTs) and determine their hydrogen
storage capacities. SWCNTs were firstly synthesized by chemical
vapor deposition (CVD) of acetylene (C2H2) on a magnesium oxide
(MgO) powder impregnated with an iron nitrate (Fe(NO3)3·9H2O)
solution. The synthesis parameters were selected as: the synthesis
temperature of 800°C, the iron content in the precursor of 5% and the
synthesis time of 30 min. Purification process of SWCNTs was
fulfilled by microwave digestion at three different temperatures (120,
150 and 200 °C), three different acid concentrations (0.5, 1 and 1.5
M) and for three different time intervals (15, 30 and 60 min). Nitric
acid (HNO3) was used in the removal of the metal catalysts. The
hydrogen storage capacities of the purified materials were measured
using volumetric method at the liquid nitrogen temperature and gas
pressure up to 100 bar. The effects of the purification conditions such
as temperature, time and acid concentration on hydrogen adsorption
were investigated.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: This paper presents a novel methodology for Maximum Power Point Tracking (MPPT) of a grid-connected 20 kW Photovoltaic (PV) system using neuro-fuzzy network. The proposed method predicts the reference PV voltage guarantying optimal power transfer between the PV generator and the main utility grid. The neuro-fuzzy network is composed of a fuzzy rule-based classifier and three Radial Basis Function Neural Networks (RBFNN). Inputs of the network (irradiance and temperature) are classified before they are fed into the appropriated RBFNN for either training or estimation process while the output is the reference voltage. The main advantage of the proposed methodology, comparing to a conventional single neural network-based approach, is the distinct generalization ability regarding to the nonlinear and dynamic behavior of a PV generator. In fact, the neuro-fuzzy network is a neural network based multi-model machine learning that defines a set of local models emulating the complex and non-linear behavior of a PV generator under a wide range of operating conditions. Simulation results under several rapid irradiance variations proved that the proposed MPPT method fulfilled the highest efficiency comparing to a conventional single neural network.
Abstract: The main issue in sweetening natural gas is H2S
dissociation. The present study is concerned with simulating thermal
dissociation of H2S in industrial natural gas carbon black furnace.
The comparison of calculated results against experimental
measurements shows good agreement. The results show that sulfur
derived from H2S thermal dissociation peaked at φ=0.95. H2S
thermal dissociation is enhanced in equivalence ratio upper than 1
and H2S oxidization is increased in equivalence ratio lower than 1.
H2 concentration of H2S thermal dissociation is increased with
increase of equivalence ratio up to 1. Also, H2S concentration
decreased in outlet as equivalence ratio increases. H2S thermal
dissociation to hydrogen and Sulfur reduces its toxic characteristics
and make economical benefits.
Abstract: This paper compares planning results of the electricity and water generation inventory up to year 2030 in the State of
Kuwait. Currently, the generation inventory consists of oil and gas fired technologies only. The planning study considers two main cases. The first case, Reference case, examines a generation inventory based on oil and gas fired generation technologies only.
The second case examines the inclusion of renewables as part of the generation inventory under two scenarios. In the first scenario, Ref-RE, renewable build-out is based on optimum economic performance
of overall generation system. Result shows that the optimum installed
renewable capacity with electric energy generation of 11% . In the second scenario, Ref-RE20, the renewable capacity build-out is
forced to provide 20% of electric energy by 2030. The respective energy systems costs of Reference, Ref-RE and Ref-RE20 case
scenarios reach US dollar 24, 10 and 14 billion annually in 2030.
Abstract: The modified Claus process is commonly used in oil
refining and gas processing to recover sulfur and destroy
contaminants formed in upstream processing. A Claus furnace feed
containing a relatively low concentration of H2S may be incapable of
producing a stable flame. Also, incomplete combustion of
hydrocarbons in the feed can lead to deterioration of the catalyst in
the reactors due to soot or carbon deposition. Therefore, special
consideration is necessary to achieve the appropriate overall sulfur
recovery. In this paper, some configurations available to treat lean
acid gas streams are described and the most appropriate ones are
studied to overcome low H2S concentration problems. As a result,
overall sulfur recovery is investigated for feed preheating and hot gas
configurations.
Abstract: This paper describes the performance of TCP Vegas
over the wireless IPv6 network. The performance of TCP Vegas is
evaluated using network simulator (ns-2). The simulation experiment
investigates how packet spacing affects the network delay, network
throughput and network efficiency of TCP Vegas. Moreover, we
investigate how the variable FTP packet sizes affect the network
performance. The result of the simulation experiment shows that as
the packet spacing is implements, the network delay is reduces,
network throughput and network efficiency is optimizes. As the FTP
packet sizes increase, the ratio of delay per throughput decreases.
From the result of experiment, we propose the appropriate packet size
in transmitting file transfer protocol application using TCP Vegas
with packet spacing enhancement over wireless IPv6 environment in
ns-2. Additionally, we suggest the appropriate ratio in determining
the appropriate RTT and buffer size in a network.
Abstract: This paper presents the impact study of apparent
reactance injected by series Flexible AC Transmission System
(FACTS) i.e. Thyristor Controlled Series Reactor (TCSR) on the
measured impedance of a 400 kV single electrical transmission line
in the presence of phase to earth fault with fault resistance. The study
deals with an electrical transmission line of Eastern Algerian
transmission networks at Group Sonelgaz (Algerian Company of
Electrical and Gas) compensated by TCSR connected at midpoint of
the line. This compensator used to inject active and reactive powers
is controlled by three TCSR-s. The simulations results investigate the
impacts of the TCSR on the parameters of short circuit calculation
and parameters of measured impedance by distance relay in the
presence of earth fault for three cases study.
Abstract: To achieve reliable solutions, today-s numerical and
experimental activities need developing more accurate methods and
utilizing expensive facilities, respectfully in microchannels. The analytical
study can be considered as an alternative approach to alleviate
the preceding difficulties. Among the analytical solutions, those with
high robustness and low complexities are certainly more attractive.
The perturbation theory has been used by many researchers to analyze
microflows. In present work, a compressible microflow with constant
heat flux boundary condition is analyzed. The flow is assumed to be
fully developed and steady. The Mach and Reynolds numbers are also
assumed to be very small. For this case, the creeping phenomenon
may have some effect on the velocity profile. To achieve robustness
solution it is assumed that the flow is quasi-isothermal. In this study,
the creeping term which appears in the slip boundary condition
is formulated by different mathematical formulas. The difference
between this work and the previous ones is that the creeping term
is taken into account and presented in non-dimensionalized form.
The results obtained from perturbation theory are presented based
on four non-dimensionalized parameters including the Reynolds,
Mach, Prandtl and Brinkman numbers. The axial velocity, normal
velocity and pressure profiles are obtained. Solutions for velocities
and pressure for two cases with different Br numbers are compared
with each other and the results show that the effect of creeping
phenomenon on the velocity profile becomes more important when
Br number is less than O(ε).
Abstract: There is an urgent need to conserve the biological diversity of the Nigerian Environment for the future and present generation in the face of current energy resources development. This paper gives an in-depth analysis of the impact of oil and gas activities on the biological diversity of the Nigerian Niger Delta area and its consequences on the sustainable development of the host communities as it relates to their social, economic and environmental issues, particularly on the womenfolk who are the key managers of environmental resources. Also reviewed is the frustration of these communities that is reflected in unending conflicts.
Abstract: An experiment of vented gas explosions involving two
different cylinder vessel volumes (0.2 and 0.0065 m3) was reported,
with equivalence ratio (Φ) ranged from 0.3 to 1.6. Both vessels were
closed at the rear end and fitted at the other side with a circular
orifice plate that gives a constant vent coefficient (K =Av/V2/3) of
16.4. It was shown that end ignition gives higher overpressures than
central ignition, even though most of the published work on venting
uses central ignition. For propane and ethylene, it is found that rich
mixtures gave the highest overpressures and these mixtures are not
considered in current vent design guidance; which the guideline is
based on mixtures giving the maximum flame temperature. A strong
influence of the vessel volume at constant K was found for methane,
propane, ethylene and hydrogen-air explosions. It can be concluded
that self- acceleration of the flame, which is dependent on the
distance of a flame from the ignition and the ‘suction’ at the vent
opening are significant factors affecting the vent flow during
explosion development in vented gas explosion. This additional
volume influence on vented explosions is not taken into account in
the current vent design guidance.
Abstract: The product development process (PDP) in the
Technology group plays a very important role in the launch of any
product. While a manufacturing process encourages the use of certain
measures to reduce health, safety and environmental (HSE) risks on
the shop floor, the PDP concentrates on the use of Geometric
Dimensioning and Tolerancing (GD&T) to develop a flawless design.
Furthermore, PDP distributes and coordinates activities between
different departments such as marketing, purchasing, and
manufacturing. However, it is seldom realized that PDP makes a
significant contribution to developing a product that reduces HSE
risks by encouraging the Technology group to use effective GD&T.
The GD&T is a precise communication tool that uses a set of
symbols, rules, and definitions to mathematically define parts to be
manufactured. It is a quality assurance method widely used in the oil
and gas sector. Traditionally it is used to ensure the
interchangeability of a part without affecting its form, fit, and
function. Parts that do not meet these requirements are rejected
during quality audits.
This paper discusses how the Technology group integrates this
quality assurance tool into the PDP and how the tool plays a major
role in helping the HSE department in its goal towards eliminating
HSE incidents. The PDP involves a thorough risk assessment and
establishes a method to address those risks during the design stage.
An illustration shows how GD&T helped reduce safety risks by
ergonomically improving assembling operations. A brief discussion
explains how tolerances provided on a part help prevent finger injury.
This tool has equipped Technology to produce fixtures, which are
used daily in operations as well as manufacturing. By applying
GD&T to create good fits, HSE risks are mitigated for operating
personnel. Both customers and service providers benefit from
reduced safety risks.
Abstract: Gas condensate Reservoirs show complicated thermodynamic behavior when their pressure reduces to under dew point pressure. Condensate blockage around the producing well cause significant reduction of production rate as well bottom-hole pressure drops below saturation pressure. The main objective of this work was to examine the well test analysis of naturally fractured lean gas condensate reservoir and investigate the effect of condensate formed around the well-bore on behavior of single phase pseudo pressure and its derivative curves. In this work a naturally fractured lean gas condensate reservoir is simulated with compositional simulator. Different sensitivity analysis done on Corry parameters and result of simulator is feed to analytical well testing software. For consideration of these phenomena eighteen compositional models with Capillary number effect are constructed. Matrix relative permeability obeys Corry relative permeability and relative permeability in fracture is linear. Well testing behavior of these models are studied and interpreted. Results show different sensitivity analysis on relative permeability of matrix does not have strong effect on well testing behavior even most part of the matrix around the well is occupied with condensate.
Abstract: In order to investigate a PROX microreactor
performance, two-dimensional modeling of the reacting flow
between two parallel plates is performed through a finite volume
method using an improved SIMPLE algorithm. A three-step surface
kinetics including hydrogen oxidation, carbon monoxide oxidation
and water-gas shift reaction is applied for a Pt-Fe/γ-Al2O3 catalyst
and operating temperatures of about 100ºC. Flow pattern, pressure
field, temperature distribution, and mole fractions of species are
found in the whole domain for all cases. Also, the required reactive
length for removing carbon monoxide from about 2% to less than 10
ppm is found. Furthermore, effects of hydraulic diameter, wall
temperature, and inlet mole fraction of air and water are investigated
by considering carbon monoxide selectivity and conversion. It is
found that air and water addition may improve the performance of
the microreactor in carbon monoxide removal in such operating
conditions; this is in agreement with the pervious published results.
Abstract: This paper has as its main aim to analyse how
corporate web pages can become an essential tool in order to detect
strategic trends by firms or sectors, and even a primary source for
benchmarking. This technique has made it possible to identify the key
issues in the strategic management of the most excellent large Spanish
firms and also to describe trends in their long-range planning, a way of
working that can be generalised to any country or firm group. More
precisely, two objectives were sought. The first one consisted in showing
the way in which corporate websites make it possible to obtain direct
information about the strategic variables which can define firms. This
tool is dynamic (since web pages are constantly updated) as well as
direct and reliable, since the information comes from the firm itself, not
from comments of third parties (such as journalists, academicians,
consultants...). When this information is analysed for a group of firms,
one can observe their characteristics in terms of both managerial tasks
and business management. As for the second objective, the methodology
proposed served to describe the corporate profile of the large Spanish
enterprises included in the Ibex35 (the Ibex35 or Iberia Index is the
reference index in the Spanish Stock Exchange and gathers periodically
the 35 most outstanding Spanish firms). An attempt is therefore made to
define the long-range planning that would be characteristic of the largest
Spanish firms.