Abstract: This paper presents an exact solution and a finite element method (FEM) for a Piezoceramic Rod under static load. The cylindrical rod is made from polarized ceramics (piezoceramics) with axial poling. The lateral surface of the rod is traction-free and is unelectroded. The two end faces are under a uniform normal traction. Electrically, the two end faces are electroded with a circuit between the electrodes, which can be switched on or off. Two cases of open and shorted electrodes (short circuit and open circuit) will be considered. Finally, a finite element model will be used to compare the results with an exact solution. The study uses ABAQUS (v.6.7) software to derive the finite element model of the ceramic rod.
Abstract: Today with the rapid growth of telecommunications equipment, electronic and developing more and more networks of power, influence of electromagnetic waves on one another has become hot topic discussions. So in this article, this issue and appropriate mechanisms for EMC operations have been presented. First, a source of alternating current (50 Hz) and a clear victim in a certain distance from the source is placed. With this simple model, the effects of electromagnetic radiation from the source to the victim will be investigated and several methods to reduce these effects have been presented. Therefore passive and active shields have been used. In some steps, shielding effectiveness of proposed shields will be compared. . It should be noted that simulations have been done by the finite element method (FEM).
Abstract: In this paper, a study on the modes of collapse of
compress- expand members are presented. Compress- expand member
is a compact, multiple-combined cylinders, to be proposed as energy
absorbers. Previous studies on the compress- expand member have
clarified its energy absorption efficiency, proposed an approximate
equation to describe its deformation characteristics and also
highlighted the improvement that it has brought. However, for the
member to be practical, the actual range of geometrical dimension that
it can maintain its applicability must be investigated. In this study,
using a virtualized materials that comply the bilinear hardening law,
Finite element Method (FEM) analysis on the collapse modes of
compress- expand member have been conducted. Deformation maps
that plotted the member's collapse modes with regards to the member's
geometric and material parameters were then presented in order to
determine the dimensional range of each collapse modes.
Abstract: –In this paper the damage in clamped-free, clampedclamped and free-free beam are analyzed considering samples
without and with structural modifications. The damage location is
investigated by the use of the bispectrum and wavelet analysis. The
mathematical models are obtained using 2D elasticity theory and the
Finite Element Method (FEM). The numerical and experimental data
are approximated using the Particle Swarm Optimizer (PSO) method
and this way is possible to adjust the localization and the severity of
the damage. The experimental data are obtained through
accelerometers placed along the sample. The system is excited using
impact hammer.
Abstract: This paper proposes a set of quasi-static mathematical
model of magnetic fields caused by high voltage conductors of
distribution transformer by using a set of second-order partial
differential equation. The modification for complex magnetic field
analysis and time-harmonic simulation are also utilized. In this
research, transformers were study in both balanced and unbalanced
loading conditions. Computer-based simulation utilizing the threedimensional
finite element method (3-D FEM) is exploited as a tool
for visualizing magnetic fields distribution volume a distribution
transformer. Finite Element Method (FEM) is one among popular
numerical methods that is able to handle problem complexity in
various forms. At present, the FEM has been widely applied in most
engineering fields. Even for problems of magnetic field distribution,
the FEM is able to estimate solutions of Maxwell-s equations
governing the power transmission systems. The computer simulation
based on the use of the FEM has been developed in MATLAB
programming environment.
Abstract: This paper deals with the thermo-mechanical deformation behavior of shear deformable functionally graded ceramicmetal (FGM) plates. Theoretical formulations are based on higher order shear deformation theory with a considerable amendment in the transverse displacement using finite element method (FEM). The mechanical properties of the plate are assumed to be temperaturedependent and graded in the thickness direction according to a powerlaw distribution in terms of the volume fractions of the constituents. The temperature field is supposed to be a uniform distribution over the plate surface (XY plane) and varied in the thickness direction only. The fundamental equations for the FGM plates are obtained using variational approach by considering traction free boundary conditions on the top and bottom faces of the plate. A C0 continuous isoparametric Lagrangian finite element with thirteen degrees of freedom per node have been employed to accomplish the results. Convergence and comparison studies have been performed to demonstrate the efficiency of the present model. The numerical results are obtained for different thickness ratios, aspect ratios, volume fraction index and temperature rise with different loading and boundary conditions. Numerical results for the FGM plates are provided in dimensionless tabular and graphical forms. The results proclaim that the temperature field and the gradient in the material properties have significant role on the thermo-mechanical deformation behavior of the FGM plates.
Abstract: High precision in motion is required to manipulate the
micro objects in precision industries for micro assembly, cell
manipulation etc. Precision manipulation is achieved based on the
appropriate mechanism design of micro devices such as
microgrippers. Design of a compliant based mechanism is the better
option to achieve a highly precised and controlled motion. This
research article highlights the method of designing a compliant based
three fingered microgripper suitable for holding asymmetric objects.
Topological optimization technique, a systematic method is
implemented in this research work to arrive a topologically optimized
design of the mechanism needed to perform the required micro
motion of the gripper. Optimization technique has a drawback of
generating senseless regions such as node to node connectivity and
staircase effect at the boundaries. Hence, it is required to have post
processing of the design to make it manufacturable. To reduce the
effect of post processing stage and to preserve the edges of the image,
a cubic spline interpolation technique is introduced in the MATLAB
program. Structural performance of the topologically developed
mechanism design is tested using finite element method (FEM)
software. Further the microgripper structure is examined to find its
fatigue life and vibration characteristics.
Abstract: This paper presents an approach which is based on the
use of supervised feed forward neural network, namely multilayer
perceptron (MLP) neural network and finite element method (FEM)
to solve the inverse problem of parameters identification. The
approach is used to identify unknown parameters of ferromagnetic
materials. The methodology used in this study consists in the
simulation of a large number of parameters in a material under test,
using the finite element method (FEM). Both variations in relative
magnetic permeability and electrical conductivity of the material
under test are considered. Then, the obtained results are used to
generate a set of vectors for the training of MLP neural network.
Finally, the obtained neural network is used to evaluate a group of
new materials, simulated by the FEM, but not belonging to the
original dataset. Noisy data, added to the probe measurements is used
to enhance the robustness of the method. The reached results
demonstrate the efficiency of the proposed approach, and encourage
future works on this subject.
Abstract: This paper presents the simulation results of electric field and potential distributions along surface of silicone rubber polymer insulators under clean and various contamination conditions with/without water droplets. Straight sheds insulator having leakage distance 290 mm was used in this study. Two type of contaminants, playwood dust and cement dust, have been studied the effect of contamination on the insulator surface. The objective of this work is to comparison the effect of contamination on potential and electric field distributions along the insulator surface when water droplets exist on the insulator surface. Finite element method (FEM) is adopted for this work. The simulation results show that contaminations have no effect on potential distribution along the insulator surface while electric field distributions are obviously depended on contamination conditions.
Abstract: Today with the rapid growth of telecommunications equipment, electronic and developing more and more networks of power, influence of electromagnetic waves on one another has become hot topic discussions. So in this article, this issue and appropriate mechanisms for EMC operations have been presented. First, impact of high voltage lines on the surrounding environment especially on the control room has been investigated, then to reduce electromagnetic radiation, various methods of shielding are provided and shielding effectiveness of them has been compared. It should be expressed that simulations have been done by the finite element method (FEM).
Abstract: In very narrow pathways, the speed of sound propagation and the phase of sound waves change due to the air viscosity. We have developed a new finite element method (FEM) that includes the effects of air viscosity for modeling a narrow sound pathway. This method is developed as an extension of the existing FEM for porous sound-absorbing materials. The numerical calculation results for several three-dimensional slit models using the proposed FEM are validated against existing calculation methods.
Abstract: In this paper, the computation of the electrical field distribution around AC high-voltage lines is demonstrated. The advantages and disadvantages of two different methods are described to evaluate the electrical field quantity. The first method is a seminumerical method using the laws of electrostatic techniques to simulate the two-dimensional electric field under the high-voltage overhead line. The second method which will be discussed is the finite element method (FEM) using specific boundary conditions to compute the two- dimensional electric field distributions in an efficient way.
Abstract: Using finite element method (FEM), the elastic
new strain-concentration factor (SNCF) of cylindrical bars
with circumferential flat-bottom groove is studied. This new
SNCF has been defined under triaxial stress state. The
employed specimens have constant groove depth with net
section and gross diameters of 10.0 and 16.7 mm,
respectively. The length of flatness ao has been varied form
0.0 ~12.5 mm to study the elastic SNCF of this type of
geometrical irregularities. The results that the elastic new
SNCF rapidly drops from its elastic value of the groove with
ao = 0.0, i.e. circumferential U-notch, and reaches minimum
value at ao = 2 mm. After that the elastic new SNCF becomes
nearly constant with increasing flatness length (ao). The value
of tensile load at yielding at the groove root increases with
increasing ao. The current results show that severity of the
notch decreases with increasing flatness length ao.
Abstract: This study is to investigate the electroencephalogram (EEG) differences generated from a normal and Alzheimer-s disease (AD) sources. We also investigate the effects of brain tissue distortions due to AD on EEG. We develop a realistic head model from T1 weighted magnetic resonance imaging (MRI) using finite element method (FEM) for normal source (somatosensory cortex (SC) in parietal lobe) and AD sources (right amygdala (RA) and left amygdala (LA) in medial temporal lobe). Then, we compare the AD sourced EEGs to the SC sourced EEG for studying the nature of potential changes due to sources and 5% to 20% brain tissue distortions. We find an average of 0.15 magnification errors produced by AD sourced EEGs. Different brain tissue distortion models also generate the maximum 0.07 magnification. EEGs obtained from AD sources and different brain tissue distortion levels vary scalp potentials from normal source, and the electrodes residing in parietal and temporal lobes are more sensitive than other electrodes for AD sourced EEG.
Abstract: In this paper presented initial design of Low Speed
Axial Flux Permanent Magnet (AFPM) Machine with Non-Slotted
TORUS topology type by use of certain algorithm (Appendix).
Validation of design algorithm studied by means of selected data of
an initial prototype machine. Analytically design calculation carried
out by means of design algorithm and obtained results compared with
results of Finite Element Method (FEM).
Abstract: The high temperature degree and uniform
Temperature Distribution (TD) on surface of cookware which contact
with food are effective factors for improving cookware application.
Additionally, the ability of pan material in retaining the heat and nonreactivity
with foods are other significant properties. It is difficult for
single material to meet a wide variety of demands such as superior
thermal and chemical properties. Multi-Layer Plate (MLP) makes
more regular TD. In this study the main objectives are to find the best
structure (single or multi-layer) and materials to provide maximum
temperature degree and uniform TD up side surface of pan. And also
heat retaining of used metals with goal of improving the thermal
quality of pan to economize the energy. To achieve this aim were
employed Finite Element Method (FEM) for analyzing transient
thermal behavior of applied materials. The analysis has been
extended for different metals, we achieved the best temperature
profile and heat retaining in Copper/ Stainless Steel MLP.
Abstract: Active Vibration Control (AVC) is an important
problem in structures. One of the ways to tackle this problem is to
make the structure smart, adaptive and self-controlling. The objective
of active vibration control is to reduce the vibration of a system by
automatic modification of the system-s structural response. This
paper features the modeling and design of a Periodic Output
Feedback (POF) control technique for the active vibration control of
a flexible Timoshenko cantilever beam for a multivariable case with
2 inputs and 2 outputs by retaining the first 2 dominant vibratory
modes using the smart structure concept. The entire structure is
modeled in state space form using the concept of piezoelectric
theory, Timoshenko beam theory, Finite Element Method (FEM) and
the state space techniques. Simulations are performed in MATLAB.
The effect of placing the sensor / actuator at 2 finite element
locations along the length of the beam is observed. The open loop
responses, closed loop responses and the tip displacements with and
without the controller are obtained and the performance of the smart
system is evaluated for active vibration control.