Abstract: In this paper, an analysis of a target location estimation
system using the best linear unbiased estimator (BLUE) for high
performance radar systems is presented. In synthetic environments,
we are here concerned with three key elements of radar system
modeling, which makes radar systems operates accurately in strategic
situation in virtual ground. Radar Cross Section (RCS) modeling
is used to determine the actual amount of electromagnetic waves
that are reflected from a tactical object. Pattern Propagation Factor
(PPF) is an attenuation coefficient of the radar equation that contains
the reflection from the surface of the earth, the diffraction, the
refraction and scattering by the atmospheric environment. Clutter is
the unwanted echoes of electronic systems. For the data fusion of
output results from radar detection in synthetic environment, BLUE
is used and compared with the mean values of each simulation results.
Simulation results demonstrate the performance of the radar system.
Abstract: Generation system reliability assessment is an
important task which can be performed using deterministic or
probabilistic techniques. The probabilistic approaches have
significant advantages over the deterministic methods. However,
more complicated modeling is required by the probabilistic
approaches. Power generation model is a basic requirement for this
assessment. One form of the generation models is the well known
capacity outage probability table (COPT). Different analytical
techniques have been used to construct the COPT. These approaches
require considerable mathematical modeling of the generating units.
The unit-s models are combined to build the COPT which will add
more burdens on the process of creating the COPT. Decimal to
Binary Conversion (DBC) technique is widely and commonly applied
in electronic systems and computing This paper proposes a novel
utilization of the DBC to create the COPT without engaging in
analytical modeling or time consuming simulations. The simple
binary representation , “0 " and “1 " is used to model the states o f
generating units. The proposed technique is proven to be an effective
approach to build the generation model.
Abstract: III-nitride quaternary InxAlyGa1-x-yN alloys have experienced considerable interest as potential materials for optoelectronic applications. Despite these interesting applications and the extensive efforts to understand their fundamental properties, research on its fundamental surface property, i.e., surface phonon polariton (SPP) has not yet been reported. In fact, the SPP properties have been shown to provide application for some photonic devices. Hence, there is an absolute need for thorough studies on the SPP properties of this material. In this work, theoretical study on the SPP modes in InAlGaN quaternary alloys are reported. Attention is focus on the wurtzite (α-) structure InxAlyGa1-x-yN semi-crystal with different In composition, x ranging from 0 to 0.10 and constant Al composition, y = 0.06. The SPP modes are obtained through the theoretical simulation by means of anisotropy model. The characteristics of SP dispersion curves are discussed. Accessible results in terms of the experimental point of view are also given. Finally, the results revealed that the SPP mode of α-InxAlyGa1-x-yN semiconductors exhibits two-mode behavior.
Abstract: By analyzing the sources of energy and power
loss in PWM (Pulse Width Modulation) controlled drivers of
water electrolysis cells, it is possible to reduce the power
dissipation and enhance the efficiency of such hydrogen
production units. A PWM controlled power driver is based on
a semiconductor switching element where its power
dissipation might be a remarkable fraction of the total power
demand of an electrolysis system. Power dissipation in a
semiconductor switching element is related to many different
parameters which could be fitted into two main categories:
switching losses and conduction losses. Conduction losses are
directly related to the built, structure and capabilities of a
switching device itself and indeed the conditions in which the
element is handling the switching application such as voltage,
current, temperature and of course the fabrication technology.
On the other hand, switching losses have some other
influencing variables other than the mentioned such as control
system, switching method and power electronics circuitry of
the PWM power driver. By analyzings the characteristics of
recently developed power switching transistors from different
families of Bipolar Junction Transistors (BJT), Metal Oxide
Semiconductor Field Effect Transistors (MOSFET) and
Insulated Gate Bipolar Transistors (IGBT), some
recommendations are made in this paper which are able to
lead to achieve higher hydrogen production efficiency by
utilizing PWM controlled water electrolysis cells.
Abstract: Recently, nanomaterials are developed in the form of nano-films, nano-crystals and nano-pores. Lanthanide phosphates as a material find extensive application as laser, ceramic, sensor, phosphor, and also in optoelectronics, medical and biological labels, solar cells and light sources. Among the different kinds of rare-earth orthophosphates, yttrium orthophosphate has been shown to be an efficient host lattice for rare earth activator ions, which have become a research focus because of their important role in the field of light display systems, lasers, and optoelectronic devices. It is in this context that the 4fn- « 4fn-1 5d transitions of rare earth in insulating materials, lying in the UV and VUV, are the aim of large number of studies .Though there has been a few reports on Eu3+, Nd3+, Pr3+,Er3+, Ce3+, Tm3+ doped YPO4. The 4fn- « 4fn-1 5d transitions of the rare earth dependent to the host-matrix, several matrices ions were used to study these transitions, in this work we are suggesting to study on a very specific class of inorganic material that are orthophosphate doped with rare earth ions. This study focused on the effect of Ce3+ concentration on the structural and optical properties of Ce3+ doped YPO4 yttrium orthophosphate with powder form prepared by the Sol Gel method.
Abstract: Cognitive Science appeared about 40 years ago,
subsequent to the challenge of the Artificial Intelligence, as common
territory for several scientific disciplines such as: IT, mathematics,
psychology, neurology, philosophy, sociology, and linguistics. The
new born science was justified by the complexity of the problems
related to the human knowledge on one hand, and on the other by the
fact that none of the above mentioned sciences could explain alone
the mental phenomena. Based on the data supplied by the
experimental sciences such as psychology or neurology, models of
the human mind operation are built in the cognition science. These
models are implemented in computer programs and/or electronic
circuits (specific to the artificial intelligence) – cognitive systems –
whose competences and performances are compared to the human
ones, leading to the psychology and neurology data reinterpretation,
respectively to the construction of new models. During these
processes if psychology provides the experimental basis, philosophy
and mathematics provides the abstraction level utterly necessary for
the intermission of the mentioned sciences.
The ongoing general problematic of the cognitive approach
provides two important types of approach: the computational one,
starting from the idea that the mental phenomenon can be reduced to
1 and 0 type calculus operations, and the connection one that
considers the thinking products as being a result of the interaction
between all the composing (included) systems. In the field of
psychology measurements in the computational register use classical
inquiries and psychometrical tests, generally based on calculus
methods. Deeming things from both sides that are representing the
cognitive science, we can notice a gap in psychological product
measurement possibilities, regarded from the connectionist
perspective, that requires the unitary understanding of the quality –
quantity whole. In such approach measurement by calculus proves to
be inefficient. Our researches, deployed for longer than 20 years,
lead to the conclusion that measuring by forms properly fits to the
connectionism laws and principles.
Abstract: This paper presents positive and negative full-wave
rectifier. The proposed structure is based on OTA using
commercially available ICs (LT1228). The features of the proposed
circuit are that: it can rectify and amplify voltage signal with
controllable output magnitude via input bias current: the output
voltage is free from temperature variation. The circuit description
merely consists of 1 single ended and 3 fully differential OTAs. The
performance of the proposed circuit are investigated though PSpice.
They show that the proposed circuit can function as positive/negative
full-wave rectifier, where the voltage input wide-dynamic range from
-5V to 5V. Furthermore, the output voltage is slightly dependent on
the temperature variations.
Abstract: Quality of 2D and 3D cross-sectional images produce
by Computed Tomography primarily depend upon the degree of
precision of primary and secondary X-Ray intensity detection.
Traditional method of primary intensity detection is apt to errors.
Recently the X-Ray intensity measurement system along with smart
X-Ray sensors is developed by our group which is able to detect
primary X-Ray intensity unerringly. In this study a new smart X-Ray
sensor is developed using Light-to-Frequency converter TSL230
from Texas Instruments which has numerous advantages in terms of
noiseless data acquisition and transmission. TSL230 construction is
based on a silicon photodiode which converts incoming X-Ray
radiation into the proportional current signal. A current to frequency
converter is attached to this photodiode on a single monolithic CMOS
integrated circuit which provides proportional frequency count to
incoming current signal in the form of the pulse train. The frequency
count is delivered to the center of PICDEM FS USB board with
PIC18F4550 microcontroller mounted on it. With highly compact
electronic hardware, this Demo Board efficiently read the smart
sensor output data. The frequency output approaches overcome
nonlinear behavior of sensors with analog output thus un-attenuated
X-Ray intensities could be measured precisely and better
normalization could be acquired in order to attain high resolution.
Abstract: This article presents a current-mode quadrature
oscillator using differential different current conveyor (DDCC) and
voltage differencing transconductance amplifier (VDTA) as active
elements. The proposed circuit is realized fro m a non-inverting
lossless integrator and an inverting second order low-pass filter. The
oscillation condition and oscillation frequency can be
electronically/orthogonally controlled via input bias currents. The
circuit description is very simple, consisting of merely 1 DDCC, 1
VDTA, 1 grounded resistor and 3 grounded capacitors. Using only
grounded elements, the proposed circuit is then suitable for IC
architecture. The proposed oscillator has high output impedance
which is easy to cascade or dive the external load without the buffer
devices. The PSPICE simulation results are depicted, and the given
results agree well with the theoretical anticipation. The power
consumption is approximately 1.76mW at ±1.25V supply voltages.
Abstract: There are three approaches to complete Bayesian
Network (BN) model construction: total expert-centred, total datacentred,
and semi data-centred. These three approaches constitute the
basis of the empirical investigation undertaken and reported in this
paper. The objective is to determine, amongst these three
approaches, which is the optimal approach for the construction of a
BN-based model for the performance assessment of students-
laboratory work in a virtual electronic laboratory environment. BN
models were constructed using all three approaches, with respect to
the focus domain, and compared using a set of optimality criteria. In
addition, the impact of the size and source of the training, on the
performance of total data-centred and semi data-centred models was
investigated. The results of the investigation provide additional
insight for BN model constructors and contribute to literature
providing supportive evidence for the conceptual feasibility and
efficiency of structure and parameter learning from data. In addition,
the results highlight other interesting themes.
Abstract: A data cutting and sorting method (DCSM) is proposed
to optimize the performance of data mining. DCSM reduces the
calculation time by getting rid of redundant data during the data
mining process. In addition, DCSM minimizes the computational units
by splitting the database and by sorting data with support counts. In the
process of searching for the relationship between metabolic syndrome
and lifestyles with the health examination database of an electronics
manufacturing company, DCSM demonstrates higher search
efficiency than the traditional Apriori algorithm in tests with different
support counts.
Abstract: Group-III nitride material as particularly AlxGa1-xN is
one of promising optoelectronic materials to require for shortwavelength
devices. To achieve the high-quality AlxGa1-xN films for
a high performance of such devices, AlN-nucleation layers are the
important factor. To improve the AlN-nucleation layers with a
variation of Ga-addition, XRD measurements were conducted to
analyze the crystalline quality of the subsequent Al0.1Ga0.9N with the
minimum ω-FWHMs of (0002) and (10-10) reflections of 425 arcsec
and 750 arcsec, respectively. SEM and AFM measurements were
performed to observe the surface morphology and TEM
measurements to identify the microstructures and orientations.
Results showed that the optimized Ga-atoms in the Al(Ga)Nnucleation
layers improved the surface diffusion to form moreuniform
crystallites in structure and size, better alignment of each
crystallite, and better homogeneity of island distribution. This, hence,
improves the orientation of epilayers on the Si-surface and finally
improves the crystalline quality and reduces the residual strain of
subsequent Al0.1Ga0.9N layers.
Abstract: The daily growing use of agents in software environments, because of many reasons such as independence and intelligence is not a secret anymore. One of such environments in which there is a prominent job for the agents would be emarketplaces in which a user is able to give those agents the responsibility of buying and selling, instead of searching the emarketplace himself. Making up a framework which has sufficient attention to the required roles and their relations, is the first step of achieving such e-markets. In this paper, we suggest a framework in order to establish such e-markets and we will continue investigating the roles such as seller or buyer and the relations in JADE environment in details.
Abstract: In this study, we experiment on precise control outlet
temperature of water from the water cooler with hot-gas bypass
method based on PI control logic for machine tool. Recently, technical
trend for machine tools is focused on enhancement of speed and
accuracy. High speedy processing causes thermal and structural
deformation of objects from the machine tools. Water cooler has to be
applied to machine tools to reduce the thermal negative influence with
accurate temperature controlling system. The goal of this study is to
minimize temperature error in steady state. In addition, control period
of an electronic expansion valve were considered to increment of
lifetime of the machine tools and quality of product with a water
cooler.
Abstract: This article presents a voltage-mode universal
biquadratic filter performing simultaneous 3 standard functions: lowpass,
high-pass and band-pass functions, employing differential
different current conveyor (DDCC) and current controlled current
conveyor (CCCII) as active element. The features of the circuit are
that: the quality factor and pole frequency can be tuned independently
via the input bias currents: the circuit description is very simple,
consisting of 1 DDCC, 2 CCCIIs, 2 electronic resistors and 2
grounded capacitors. Without requiring component matching
conditions, the proposed circuit is very appropriate to further develop
into an integrated circuit. The PSPICE simulation results are
depicted. The given results agree well with the theoretical
anticipation.
Abstract: Online auctions are not very popular in Croatia. The
main reason for this is a very limited number of services which can
be used by Croatian users. Until recent times, even selling through
the most popular online auction site eBay wasn't possible because
PayPal services could not make payment to bank or debit card
accounts in Croatia. Furthermore, many foreign sellers do not offer
delivery of their products to Croatia which means that large
quantities of goods initially offered on such sites are not available.
With that in mind, it is necessary to analyze the buying and selling
habits of Croatian users and existing online auction sites, both
Croatian and foreign, and create a model for new domestic site. This
site will have to exploit every positive aspect of existing models and
neutralize every negative perception indicated by users in the survey
so that, hopefully, it would attract new users.
Abstract: This paper presents a new method of analog fault diagnosis based on back-propagation neural networks (BPNNs) using wavelet decomposition and fractal dimension as preprocessors. The proposed method has the capability to detect and identify faulty components in an analog electronic circuit with tolerance by analyzing its impulse response. Using wavelet decomposition to preprocess the impulse response drastically de-noises the inputs to the neural network. The second preprocessing by fractal dimension can extract unique features, which are the fed to a neural network as inputs for further classification. A comparison of our work with [1] and [6], which also employs back-propagation (BP) neural networks, reveals that our system requires a much smaller network and performs significantly better in fault diagnosis of analog circuits due to our proposed preprocessing techniques.
Abstract: This paper proposed a novel model for short term load
forecast (STLF) in the electricity market. The prior electricity
demand data are treated as time series. The model is composed of
several neural networks whose data are processed using a wavelet
technique. The model is created in the form of a simulation program
written with MATLAB. The load data are treated as time series data.
They are decomposed into several wavelet coefficient series using
the wavelet transform technique known as Non-decimated Wavelet
Transform (NWT). The reason for using this technique is the belief
in the possibility of extracting hidden patterns from the time series
data. The wavelet coefficient series are used to train the neural
networks (NNs) and used as the inputs to the NNs for electricity load
prediction. The Scale Conjugate Gradient (SCG) algorithm is used as
the learning algorithm for the NNs. To get the final forecast data, the
outputs from the NNs are recombined using the same wavelet
technique. The model was evaluated with the electricity load data of
Electronic Engineering Department in Mandalay Technological
University in Myanmar. The simulation results showed that the
model was capable of producing a reasonable forecasting accuracy in
STLF.
Abstract: Software testing is important stage of software development cycle. Current testing process involves tester and electronic documents with test case scenarios. In this paper we focus on new approach to testing process using automated test case generation and tester guidance through the system based on the model of the system. Test case generation and model-based testing is not possible without proper system model. We aim on providing better feedback from the testing process thus eliminating the unnecessary paper work.
Abstract: This paper presents the design related to the
electronic system design of the respiratory signal, including phases
for processing, followed by the transmission and reception of this
signal and finally display. The processing of this signal is added to
the ECG and temperature sign, put up last year. Under this scheme is
proposed that in future also be conditioned blood pressure signal
under the same final printed circuit and worked.