Abstract: In the present work flow past circular cylinder and
cylinder with rectangular and triangular wake splitter is studied to
improve aerodynamic parameters. The Comparison of drag
coefficient is tabulated for bare cylinder, cylinder with rectangular
and triangular wake splitters. Flow past circular cylinder and cylinder
with triangular and rectangular wake splitter is performed at
Reynoldsnumber 5, 20, 40, 50,80, 100.An incompressible PISO finite
volume code employing a non-staggered grid arrangement is used, a
second order upwind scheme is used for convective terms. The time
discretization is implicit and a Second order Crank-Nicholson scheme
is employed. Length of wake splitter in both configurations is taken
to be equal to diameter of cylinder. Wake length is found to be less
with rectangular wake splitter when compared to bare cylinder and
cylinder with triangular wake splitter. Coefficient of drag is found to
be less for triangular wake splitter when compared to bare cylinder &
cylinder with rectangular wake splitter.
Abstract: the work contains the results of complex investigation
related to the evaluation of condition of working blades of gas turbine
engines during fatigue tests by applying the acoustic emission
method. It demonstrates the possibility of estimating the fatigue
damage of blades in the process of factory tests. The acoustic
emission criteria for detecting and testing the kinetics of fatigue crack
distribution were detected. It also shows the high effectiveness of the
method for non-destructive testing of condition of solid and cooled
working blades for high-temperature gas turbine engines.
Abstract: The world demand for potable water is
increasing every day with growing population. Desalination
using solar energy is suitable for potable water production
from brackish and seawater. In this paper, we present a
theoretical study of solar distillation in a single basin under
the open environmental conditions of Chabahar-Iran. The still
has a base area of 2000mm×500mm with a glass cover
inclined at 25° in order to obtain extra solar energy. We model
the still and conduct its energy balance equations under minor
assumptions. We computed the temperatures of glass cover,
seawater interface, moist air and bottom using numerical
method. The investigation addressed the following: The still
productivity, distilled water salinity and still performance in
terms of the still efficiency. Calculated still productivity in
July was higher than December. So in this paper, we show
that still productivity is directly functioning of solar radiation.
Abstract: Car failure detection is a complicated process and
requires high level of expertise. Any attempt of developing an expert
system dealing with car failure detection has to overcome various
difficulties. This paper describes a proposed knowledge-based
system for car failure detection. The paper explains the need for an
expert system and the some issues on developing knowledge-based
systems, the car failure detection process and the difficulties involved
in developing the system. The system structure and its components
and their functions are described. The system has about 150 rules for
different types of failures and causes. It can detect over 100 types of
failures. The system has been tested and gave promising results.
Abstract: The emergence of mobile application services and App
Store has led to the explosive growth of user innovation, which users
voluntarily contribute to. User innovation communities where end
users freely reveal innovative ideas and needs with other community
members are becoming increasingly influential in this area. However,
user-s ideas in user innovation community are not enough to be new
service opportunity, because some of them can already developed as
existing services in App Store. Moreover, the existing services similar
to new service opportunity can be significant references to apply
analogy to develop service concept. In response, this research
proposes Case-Based Reasoning approach to matching the user needs
and existing services, identifying unmet opportunistic user needs, and
retrieving similar services with opportunity. Due to its intuitive and
transparent algorithm, users related to App Store innovation
communities can easily employ Case-Based Reasoning based
approach to their innovation.
Abstract: By employing BS (Base Station) cooperation we can
increase substantially the spectral efficiency and capacity of cellular
systems. The signals received at each BS are sent to a central unit that
performs the separation of the different MT (Mobile Terminal) using
the same physical channel. However, we need accurate sampling and
quantization of those signals so as to reduce the backhaul
communication requirements.
In this paper we consider the optimization of the quantizers for BS
cooperation systems. Four different quantizer types are analyzed and
optimized to allow better SQNR (Signal-to-Quantization Noise
Ratio) and BER (Bit Error Rate) performance.
Abstract: An empirical study of web applications that use
software frameworks is presented here. The analysis is based on two
approaches. In the first, developers using such frameworks are
required, based on their experience, to assign weights to parameters
such as database connection. In the second approach, a performance
testing tool, OpenSTA, is used to compute start time and other such
measures. From such an analysis, it is concluded that open source
software is superior to proprietary software. The motivation behind
this research is to examine ways in which a quantitative assessment
can be made of software in general and frameworks in particular.
Concepts such as metrics and architectural styles are discussed along
with previously published research.
Abstract: The most important parameter in transformers life
expectancy is the hot-spot temperature level which accelerates the
rate of aging of the insulation. The aim of this paper is to present
thermal models for transformers loaded at prefabricated MV/LV
transformer substations and outdoor situations. The hot-spot
temperature of transformers is studied using their top-oil temperature
rise models. The thermal models proposed for hot-spot and top-oil
temperatures of different operating situations are compared. Since the
thermal transfer is different for indoor and outdoor transformers
considering their operating conditions, their hot-spot thermal models
differ from each other. The proposed thermal models are verified by
the results obtained from the experiments carried out on a typical
1600 kVA, 30 /0.4 kV, ONAN transformer for both indoor and
outdoor situations.
Abstract: This paper presents a new method of analog fault diagnosis based on back-propagation neural networks (BPNNs) using wavelet decomposition and fractal dimension as preprocessors. The proposed method has the capability to detect and identify faulty components in an analog electronic circuit with tolerance by analyzing its impulse response. Using wavelet decomposition to preprocess the impulse response drastically de-noises the inputs to the neural network. The second preprocessing by fractal dimension can extract unique features, which are the fed to a neural network as inputs for further classification. A comparison of our work with [1] and [6], which also employs back-propagation (BP) neural networks, reveals that our system requires a much smaller network and performs significantly better in fault diagnosis of analog circuits due to our proposed preprocessing techniques.
Abstract: In this paper, we study a class of serially concatenated block codes (SCBC) based on matrix interleavers, to be employed in fixed wireless communication systems. The performances of SCBC¬coded systems are investigated under various interleaver dimensions. Numerical results reveal that the matrix interleaver could be a competitive candidate over conventional block interleaver for frame lengths of 200 bits; hence, the SCBC coding based on matrix interleaver is a promising technique to be employed for speech transmission applications in many international standards such as pan-European Global System for Mobile communications (GSM), Digital Cellular Systems (DCS) 1800, and Joint Detection Code Division Multiple Access (JD-CDMA) mobile radio systems, where the speech frame contains around 200 bits.
Abstract: Reciprocating compressors are flexible to handle wide capacity and condition swings, offer a very efficient method of compressing almost any gas mixture in wide range of pressure, can generate high head independent of density, and have numerous applications and wide power ratings. These make them vital component in various units of industrial plants. In this paper optimum reciprocating compressor configuration regarding interstage pressures, low suction pressure, non-lubricated cylinder, speed of machine, capacity control system, compressor valve, lubrication system, piston rod coating, cylinder liner material, barring device, pressure drops, rod load, pin reversal, discharge temperature, cylinder coolant system, performance, flow, coupling, special tools, condition monitoring (including vibration, thermal and rod drop monitoring), commercial points, delivery and acoustic conditions are presented.
Abstract: The paper deals with an application of quantitative analysis – the Data Envelopment Analysis (DEA) method to performance evaluation of the European Union Member States, in the reference years 2000 and 2011. The main aim of the paper is to measure efficiency changes over the reference years and to analyze a level of productivity in individual countries based on DEA method and to classify the EU Member States to homogeneous units (clusters) according to efficiency results. The theoretical part is devoted to the fundamental basis of performance theory and the methodology of DEA. The empirical part is aimed at measuring degree of productivity and level of efficiency changes of evaluated countries by basic DEA model – CCR CRS model, and specialized DEA approach – the Malmquist Index measuring the change of technical efficiency and the movement of production possibility frontier. Here, DEA method becomes a suitable tool for setting a competitive/uncompetitive position of each country because there is not only one factor evaluated, but a set of different factors that determine the degree of economic development.
Abstract: This paper aims at presenting the biotechnology used
to obtain collagen-based gels from shark (Squalus acanthias) and brill
skin, marine fish growing in the Black Sea. Due to the structure of its
micro-fibres, collagen can be considered a nanomaterial; in order to
use collagen-based matrixes as biomaterial, rheological studies must
be performed first, to state whether they are stable or not. For the
triple-helix structure to remain stable within these gels at room or
human body temperature, they must be stabilized by reticulation.
Abstract: In this study spatial-temporal speckle correlation techniques have been applied for the quality evaluation of three different Indian fruits namely apple, pear and tomato for the first time. The method is based on the analysis of variations of laser light scattered from biological samples. The results showed that crosscorrelation coefficients of biospeckle patterns change subject to their freshness and the storage conditions. The biospeckle activity was determined by means of the cross-correlation functions of the intensity fluctuations. Significant changes in biospeckle activity were observed during their shelf lives. From the study, it is found that the biospeckle activity decreases with the shelf-life storage time. Further it has been shown that biospeckle activity changes according to their respiration rates.
Abstract: The purpose of this paper is to examine the current
state of corporate social responsibility statements on corporate
websites of Malaysian and Singaporean corporations and analyze
how the CSR statements contribute in building a unique corporate
identity of corporations. Content analysis is employed to examine the
websites of Malaysian and Singaporean consumer corporations. It is
believed that generally most companies tend to publish and
communicate their CSR statements visibly to general stakeholders.
However, there is a significantly different outcome of the articulation
of CSR on practices on websites between Malaysian and Singaporean
consumer corporations. A number of Singaporean organizations were
found less concerned with CSR practices as compared to Malaysian
organizations. The findings indicate a need for corporations in
Malaysia and Singapore to orchestrate their core competence of CSR
activities in order to develop a unique corporate identity in a global
business environment.
Abstract: This paper presents the design related to the
electronic system design of the respiratory signal, including phases
for processing, followed by the transmission and reception of this
signal and finally display. The processing of this signal is added to
the ECG and temperature sign, put up last year. Under this scheme is
proposed that in future also be conditioned blood pressure signal
under the same final printed circuit and worked.
Abstract: Refractive index control of benzocyclobutene (BCB 4024-40) is achieved by facilitating different conditions during the thermal curing of BCB film. Refractive index (RI) change of 1.49% is obtained with curing of BCB film using an oven, while the RI change is 0.1% when the BCB is cured using a hotplate. The two different curing methods exhibit a temperature dependent refractive index change of the BCB photosensitive polymer. By carefully controlling the curing conditions, multiple layers of BCB with different RI can be fabricated, which can then be applied in the fabrication of optical waveguides.
Abstract: Undoubtedly, chassis is one of the most important
parts of a vehicle. Chassis that today are produced for vehicles are
made up of four parts. These parts are jointed together by screwing.
Transverse parts are called cross member.
This study reviews the stress generated by cyclic laboratory loads
in front cross member of Peugeot 405. In this paper the finite element
method is used to simulate the welding process and to determine the
physical response of the spot-welded joints. Analysis is done by the
Abaqus software.
The Stresses generated in cross member structure are generally
classified into two groups: The stresses remained in form of residual
stresses after welding process and the mechanical stress generated by
cyclic load. Accordingly the total stress must be obtained by
determining residual stress and mechanical stress separately and then
sum them according to the superposition principle.
In order to improve accuracy, material properties including
physical, thermal and mechanical properties were supposed to be
temperature-dependent. Simulation shows that maximum Von Misses
stresses are located at special points. The model results are then
compared to the experimental results which are reported by
producing factory and good agreement is observed.
Abstract: The oil and gas industry has moved towards Load and
Resistance Factor Design through API RP2A - LRFD and the
recently published international standard, ISO-19902, for design of
fixed steel offshore structures. The ISO 19902 is intended to provide
a harmonized design practice that offers a balanced structural fitness
for the purpose, economy and safety. As part of an ongoing work, the
reliability analysis of tubular joints of the jacket structure has been
carried out to calibrate the load and resistance factors for the design
of offshore platforms in Malaysia, as proposed in the ISO.
Probabilistic models have been established for the load effects (wave,
wind and current) and the tubular joints strengths. In this study the
First Order Reliability Method (FORM), coded in MATLAB
Software has been employed to evaluate the reliability index of the
typical joints, designed using API RP2A - WSD and ISO 19902.
Abstract: Short term electricity demand forecasts are required
by power utilities for efficient operation of the power grid. In a
competitive market environment, suppliers and large consumers also
require short term forecasts in order to estimate their energy
requirements in advance. Electricity demand is influenced (among
other things) by the day of the week, the time of year and special
periods and/or days such as Ramadhan, all of which must be
identified prior to modelling. This identification, known as day-type
identification, must be included in the modelling stage either by
segmenting the data and modelling each day-type separately or by
including the day-type as an input. Day-type identification is the
main focus of this paper. A Kohonen map is employed to identify the
separate day-types in Algerian data.