Abstract: This paper investigates the problem of automated defect
detection for textile fabrics and proposes a new optimal filter design
method to solve this problem. Gabor Wavelet Network (GWN) is
chosen as the major technique to extract the texture features from
textile fabrics. Based on the features extracted, an optimal Gabor filter
can be designed. In view of this optimal filter, a new semi-supervised
defect detection scheme is proposed, which consists of one real-valued
Gabor filter and one smoothing filter. The performance of the scheme
is evaluated by using an offline test database with 78 homogeneous
textile images. The test results exhibit accurate defect detection with
low false alarm, thus showing the effectiveness and robustness of the
proposed scheme. To evaluate the detection scheme comprehensively,
a prototyped detection system is developed to conduct a real time test.
The experiment results obtained confirm the efficiency and
effectiveness of the proposed detection scheme.
Abstract: Rolling element bearings are widely used in industry,
especially where high load capacity is required. The diagnosis of
their conditions is essential matter for downtime reduction and saving
cost of maintenance. Therefore, an intensive analysis of frequency
spectrum of their faults must be carried out in order to determine the
main reason of the fault. This paper focus on a beating phenomena
observed in the waveform (time domain) of a cylindrical rolling
element bearing. The beating frequencies were not related to any
sources nearby the machine nor any other malfunctions (unbalance,
misalignment ...etc). More investigation on the spike energy and the
frequency spectrum indicated a problem with races of the bearing.
Multi-harmonics of the fundamental defects frequencies were
observed. Two of them were close to each other in magnitude those
were the source of the beating phenomena.
Abstract: Building inspection is one of the key components of building maintenance. The primary purpose of performing a building inspection is to evaluate the building-s condition. Without inspection, it is difficult to determine a built asset-s current condition, so failure to inspect can contribute to the asset-s future failure. Traditionally, a longhand survey description has been widely used for property condition reports. Surveys that employ ratings instead of descriptions are gaining wide acceptance in the industry because they cater to the need for numerical analysis output. These kinds of surveys are also in keeping with the new RICS HomeBuyer Report 2009. In this paper, we propose a new assessment method, derived from the current rating systems, for assessing the specifically smart school building-s condition and rating the seriousness of each defect identified. These two assessment criteria are then multiplied to find the building-s score, which we called the Condition Survey Protocol (CSP) 1 Matrix. Instead of a longhand description of a building-s defects, this matrix requires concise explanations about the defects identified, thus saving on-site time during a smart school building inspection. The full score is used to give the building an overall rating: Good, Fair or Dilapidated.
Abstract: The fixed partial dentures are mainly used in the frontal
part of the dental arch because of their great esthetics. There are
several factors that are associated with the stress state created in
ceramic restorations, including: thickness of ceramic layers,
mechanical properties of the materials, elastic modulus of the
supporting substrate material, direction, magnitude and frequency of
applied load, size and location of occlusal contact areas, residual
stresses induced by processing or pores, restoration-cement
interfacial defects and environmental defects. The purpose of this
study is to evaluate the capability of Polarization Sensitive Optical
Coherence Tomography (PSOCT) in detection and analysis of
possible material defects in metal-ceramic and integral ceramic fixed
partial dentures. As a conclusion, it is important to have a non
invasive method to investigate fixed partial prostheses before their
insertion in the oral cavity in order to satisfy the high stress
requirements and the esthetic function.
Abstract: An investigation of the process of deformation hardening and evolution of deformation defect medium in dispersion-hardened materials with face centered cubic matrices and nanoparticles was done. Mathematical model including balance equation for the deformation defects was used.
Abstract: This paper proposes a novel methodology for enabling
debugging and tracing of production web applications without
affecting its normal flow and functionality. This method of debugging
enables developers and maintenance engineers to replace a set of
existing resources such as images, server side scripts, cascading
style sheets with another set of resources per web session. The new
resources will only be active in the debug session and other sessions
will not be affected. This methodology will help developers in tracing
defects, especially those that appear only in production environments
and in exploring the behaviour of the system. A realization of the
proposed methodology has been implemented in Java.
Abstract: This paper is devoted to present and discuss a model that allows a local segmentation by using statistical information of a given image. It is based on Chan-Vese model, curve evolution, partial differential equations and binary level sets method. The proposed model uses the piecewise constant approximation of Chan-Vese model to compute Signed Pressure Force (SPF) function, this one attracts the curve to the true object(s)-s boundaries. The implemented model is used to extract weld defects from weld radiographic images in the aim to calculate the perimeter and surfaces of those weld defects; encouraged resultants are obtained on synthetic and real radiographic images.
Abstract: Quaternary InxAlyGa1-x-yN semiconductors have
attracted much research interest because the use of this quaternary
offer the great flexibility in tailoring their band gap profile while
maintaining their lattice-matching and structural integrity. The
structural and optical properties of InxAlyGa1-x-yN alloys grown by
molecular beam epitaxy (MBE) is presented. The structural quality of
InxAlyGa1-x-yN layers was characterized using high-resolution X-ray
diffraction (HRXRD). The results confirm that the InxAlyGa1-x-yN
films had wurtzite structure and without phase separation. As the In
composition increases, the Bragg angle of the (0002) InxAlyGa1-x-yN
peak gradually decreases, indicating the increase in the lattice constant
c of the alloys. FWHM of (0002) InxAlyGa1-x-yN decreases with
increasing In composition from 0 to 0.04, that could indicate the
decrease of quality of the samples due to point defects leading to
non-uniformity of the epilayers. UV-VIS spectroscopy have been used
to study the energy band gap of InxAlyGa1-x-yN. As the indium (In)
compositions increases, the energy band gap decreases. However, for
InxAlyGa1-x-yN with In composition of 0.1, the band gap shows a
sudden increase in energy. This is probably due to local alloy
compositional fluctuations in the epilayer. The bowing parameter
which appears also to be very sensitive on In content is investigated
and obtained b = 50.08 for quaternary InxAlyGa1-x-yN alloys. From
photoluminescence (PL) measurement, green luminescence (GL)
appears at PL spectrum of InxAlyGa1-x-yN, emitted for all x at ~530 nm
and it become more pronounced as the In composition (x) increased,
which is believed cause by gallium vacancies and related to isolated
native defects.
Abstract: Manufacturing tolerancing is intended to determine
the intermediate geometrical and dimensional states of the part
during its manufacturing process. These manufacturing dimensions
also serve to satisfy not only the functional requirements given in
the definition drawing, but also the manufacturing constraints, for
example geometrical defects of the machine, vibration and the
wear of the cutting tool. In this paper, an experimental study on the
influence of the wear of the cutting tool (systematic dispersions) is
explored. This study was carried out on three stages .The first stage
allows machining without elimination of dispersions (random,
systematic) so the tolerances of manufacture according to total
dispersions. In the second stage, the results of the first stage are
filtered in such way to obtain the tolerances according to random
dispersions. Finally, from the two previous stages, the systematic
dispersions are generated. The objective of this study is to model
by the least squares method the error of manufacture based on
systematic dispersion. Finally, an approach of optimization of the
manufacturing tolerances was developed for machining on a CNC
machine tool
Abstract: MicroRNAs are an important class of gene expression
regulators that are involved in many biological processes including
embryogenesis. miR-125b is a conserved microRNA that is enriched
in the nervous system. We have previously reported the function of
miR-125b in neuronal differentiation of human cell lines. We also
discovered the function of miR-125b in regulating p53 in human and
zebrafish. Here we further characterize the brain defects in zebrafish
embryos injected with morpholinos against miR-125b. Our data
confirm the essential role of miR-125b in brain morphogenesis
particularly in maintaining the balance between proliferation, cell
death and differentiation. We identified lunatic fringe (lfng) as an
additional target of miR-125b in human and zebrafish and suggest
that lfng may mediate the function of miR-125b in neurogenesis.
Together, this report reveals new insights into the function of miR-
125b during neural development of zebrafish.
Abstract: In this document, we have proposed a robust
conceptual strategy, in order to improve the robustness against the manufacturing defects and thus the reliability of logic CMOS circuits. However, in order to enable the use of future CMOS
technology nodes this strategy combines various types of design:
DFR (Design for Reliability), techniques of tolerance: hardware
redundancy TMR (Triple Modular Redundancy) for hard error
tolerance, the DFT (Design for Testability. The Results on largest ISCAS and ITC benchmark circuits show that our approach improves
considerably the reliability, by reducing the key factors, the area costs and fault tolerance probability.
Abstract: The main aim of this study is to identify the most
influential variables that cause defects on the items produced by a
casting company located in Turkey. To this end, one of the items
produced by the company with high defective percentage rates is
selected. Two approaches-the regression analysis and decision treesare
used to model the relationship between process parameters and
defect types. Although logistic regression models failed, decision tree
model gives meaningful results. Based on these results, it can be
claimed that the decision tree approach is a promising technique for
determining the most important process variables.
Abstract: When the Malaysian government announced the implementation of the Build-Then-Sell (BTS) system in 2007, the proponents of the BTS have argued that the implementation of this new system may provide houses with low defects. However, there has been no empirical data to support their argument. Therefore, this study is conducted to measure the level of housing defects in the BTS housing delivery system. A survey was conducted to the occupiers in six BTS residential areas. The BTS residential areas have been identified through the media and because of the small number of population, all households in the BTS residential areas were required to participate in the study to enable the researcher to collect the data concerning defects. Questionnaire had been employed as the data collection instrument and was distributed to the respondents of this study. The result has shown that the level of defects in the BTS houses is low, as the rate of defects for all elements are slight. Such low level of defects has apparently only affected the aesthetic value of the houses.
Abstract: The vibrations produced by a single point defect on
various parts of the bearing under constant radial load are predicted
by using a theoretical model. The model includes variation in the
response due to the effect of bearing dimensions, rotating frequency
distribution of load. The excitation forces are generated when the
defects on the races strike to rolling elements. In case of the outer
ring defect, the pulses generated are with periodicity of outer ring
defect frequency where as for inner ring defect, the pulses are with
periodicity of inner ring defect frequency. The effort has been carried
out in preparing the physical model of the system. Different defect
frequencies are obtained and are used to find out the amplitudes of
the vibration due to excitation of the bearing parts. Increase in the
radial load or severity of the defect produces a significant change in
bearing signature characteristics.
Abstract: The accuracy of estimated stability and control
derivatives of a light aircraft from flight test data were evaluated. The light aircraft, named ChangGong-91, is the first certified aircraft from
the Korean government. The output error method, which is a maximum likelihood estimation technique and considers measurement
noise only, was used to analyze the aircraft responses measures. The
multi-step control inputs were applied in order to excite the short period mode for the longitudinal and Dutch-roll mode for the lateral-directional motion. The estimated stability/control derivatives of Chan Gong-91 were analyzed for the assessment of handling
qualities comparing them with those of similar aircraft. The accuracy of the flight derivative estimates derived from flight test measurement
was examined in engineering judgment, scatter and Cramer-Rao bound, which turned out to be satisfactory with minor defects..
Abstract: Software metric is a measure of some property of a
piece of software or its specification. The aim of this paper is to
present an application of evolutionary decision trees in software
engineering in order to classify the software modules that have or
have not one or more reported defects. For this some metrics are used
for detecting the class of modules with defects or without defects.
Abstract: Measurements of capacitance C and dissipation
factor tand of the stator insulation system provide useful information
about internal defects within the insulation. The index k is defined as
the proportionality constant between the changes at high voltage of
capacitance DC and of the dissipation factor Dtand . DC and
Dtand values were highly correlated when small flat defects were
within the insulation and that correlation was lost in the presence of
large narrow defects like electrical treeing. The discrimination
between small and large defects is made resorting to partial discharge
PD phase angle analysis. For the validation of the results, C and tand
measurements were carried out in a 15MVA 4160V steam turbine
turbogenerator placed in a sugar mill. In addition, laboratory test
results obtained by other authors were analyzed jointly. In such
laboratory tests, model coil bars subjected to thermal cycling resulted
highly degraded and DC and Dtand values were not correlated. Thus,
the index k could not be calculated.
Abstract: In this work we present the modelling of the induction
machine, taking into consideration the stator defects of the induction
machine. It is based on the theory of electromagnetic coupling of
electrical circuits. In fact, for the modelling of stationary defects such
as short circuit between turns in the same phase, we introduce only
in the matrix the coefficients of resistance and inductance of stator
and in the mutual inductance stator-rotor. These coefficients take
account the number of turns in short-circuit deducted from the total
number of turns in the same phase; in this way we obtain the number
of useful turns. In addition, all these faults involved, will be used for
the creation of the database that will be used to develop an automated
system failures of the induction machine.
Abstract: The present work analyses different parameters of pressure die casting to minimize the casting defects. Pressure diecasting is usually applied for casting of aluminium alloys. Good surface finish with required tolerances and dimensional accuracy can be achieved by optimization of controllable process parameters such as solidification time, molten temperature, filling time, injection pressure and plunger velocity. Moreover, by selection of optimum process parameters the pressure die casting defects such as porosity, insufficient spread of molten material, flash etc. are also minimized. Therefore, a pressure die casting component, carburetor housing of aluminium alloy (Al2Si2O5) has been considered. The effects of selected process parameters on casting defects and subsequent setting of parameters with the levels have been accomplished by Taguchi-s parameter design approach. The experiments have been performed as per the combination of levels of different process parameters suggested by L18 orthogonal array. Analyses of variance have been performed for mean and signal-to-noise ratio to estimate the percent contribution of different process parameters. Confidence interval has also been estimated for 95% consistency level and three conformational experiments have been performed to validate the optimum level of different parameters. Overall 2.352% reduction in defects has been observed with the help of suggested optimum process parameters.
Abstract: Tensile armour wires provide a flexible pipe's
resistance to longitudinal stresses. Flexible pipe manufacturers need
to know the effect of defects such as scratches and cracks, with
dimensions less than 0.2mm which is the limit of the current nondestructive
detection technology, on the fracture stress and fracture
strain of the wire for quality assurance purposes. Recent research
involving the determination of the fracture strength of cracked wires
employed laboratory testing and classical fracture mechanics
approach using non-standardised fracture mechanics specimens
because standard test specimens could not be manufactured from the
wires owing to their sizes. In this work, the effect of miniature
cracks on the fracture properties of tensile armour wires was
investigated using laboratory and finite element tensile testing
simulations with the phenomenological shear fracture model. The
investigation revealed that the presence of cracks shallower than
0.2mm is worse on the fracture strain of the wire.