Abstract: A cross sectional study design and standard
microbiological procedures were used to determine the prevalence
and antimicrobial susceptibility patterns of Escherichia coli,
Salmonella enterica serovar typhimurium and Vibrio cholerae O1
isolated from water and two fish species Rastrineobola argentea and
Oreochromis niloticus collected from fish landing beaches and
markets in the Lake Victoria Basin of western Kenya. Out of 162
samples analyzed, 133 (82.1%) were contaminated, with S.
typhimurium as the most prevalent (49.6%), followed by E. coli
(46.6%), and lastly V. cholerae (2.8%). All the bacteria isolates were
sensitive to ciprofloxacin. E. coli isolates were resistant to ampicillin,
tetracycline, cotrimoxazole, chloramphenical and gentamicin while
S. typhimurium isolates exhibited resistance to ampicillin,
tetracycline, and cotrimoxazole. The V. cholerae O1 isolates were
resistant to tetracycline and ampicillin. The high prevalence of drug
resistant enteric bacteria in water and fish from the study region
needs public health intervention from the local government.
Abstract: the elastic scattering of protons, deuterons and 3He on 6Li at different incident energies have been analyzed in the framework of the optical model using ECIS88 as well as SPI GENOA codes. The potential parameters were extracted in the phenomenological treatment of measured by us angular distributions and literature data. A good agreement between theoretical and experimental differential cross sections was obtained in whole angular range. Parameters for real part of potential have been also calculated microscopically with singleand double-folding model for the p and d, 3He scattering, respectively, using DFPOT code. For best agreement with experiment the normalization factor N for the potential depth is obtained in the range of 0.7-0.9.
Abstract: An attempt has been made to develop a
seminumerical model to study temperature variations in dermal
layers of human limbs. The model has been developed for two
dimensional steady state case. The human limb has been assumed to
have elliptical cross section. The dermal region has been divided
into three natural layers namely epidermis, dermis and subdermal
tissues. The model incorporates the effect of important physiological
parameters like blood mass flow rate, metabolic heat generation, and
thermal conductivity of the tissues. The outer surface of the limb is
exposed to the environment and it is assumed that heat loss takes
place at the outer surface by conduction, convection, radiation, and
evaporation. The temperature of inner core of the limb also varies at
the lower atmospheric temperature. Appropriate boundary conditions
have been framed based on the physical conditions of the problem.
Cubic splines approach has been employed along radial direction and
Fourier series along angular direction to obtain the solution. The
numerical results have been computed for different values of
eccentricity resembling with the elliptic cross section of the human
limbs. The numerical results have been used to obtain the
temperature profile and to study the relationships among the various
physiological parameters.
Abstract: Com Poisson distribution is capable of modeling the count responses irrespective of their mean variance relation and the parameters of this distribution when fitted to a simple cross sectional data can be efficiently estimated using maximum likelihood (ML) method. In the regression setup, however, ML estimation of the parameters of the Com Poisson based generalized linear model is computationally intensive. In this paper, we propose to use quasilikelihood (QL) approach to estimate the effect of the covariates on the Com Poisson counts and investigate the performance of this method with respect to the ML method. QL estimates are consistent and almost as efficient as ML estimates. The simulation studies show that the efficiency loss in the estimation of all the parameters using QL approach as compared to ML approach is quite negligible, whereas QL approach is lesser involving than ML approach.
Abstract: Vortex-shedding phenomenon of the flow
around combined two bodies having various geometries and sizes has been investigated experimentally in the Reynolds
number range between 4.1x103 and 1.75x104. To see the effect
of the rotation of the bodies on the vortex shedding, the
combined bodies were rotated from 0° to 180°. The combined models have a cross section composing of a main circular cylinder and an attached circular or square cylinder. Results
have shown that Strouhal numbers for two cases were
changed considerably with the angle of incidence, while it was found to be largely independent of Reynolds number at 150. Characteristics of the vortex formation region and
location of flow attachments, reattachments, and separations
were observed by means of the flow visualizations.
Depending on the inclination angle the effects of flow
attachment, separation and reattachment on vortex-shedding phenomenon have been discussed.
Abstract: Since polymerase chain reaction (PCR) has been
invented, it has emerged as a powerful tool in genetic analysis. The
PCR products are closely linked with thermal cycles. Therefore, to
reduce the reaction time and make temperature distribution uniform in
the reaction chamber, a novel oscillatory thermal cycler is designed.
The sample is placed in a fixed chamber, and three constant isothermal
zones are established and lined in the system. The sample is oscillated
and contacted with three different isothermal zones to complete
thermal cycles. This study presents the design of the geometric
characteristics of the chamber. The commercial software
CFD-ACE+TM is utilized to investigate the influences of various
materials, heating times, chamber volumes, and moving speed of the
chamber on the temperature distributions inside the chamber. The
chamber moves at a specific velocity and the boundary conditions
with time variations are related to the moving speed. Whereas the
chamber moves, the boundary is specified at the conditions of the
convection or the uniform temperature. The user subroutines compiled
by the FORTRAN language are used to make the numerical results
realistically. Results show that the reaction chamber with a rectangular
prism is heated on six faces; the effects of various moving speeds of
the chamber on the temperature distributions are examined. Regarding
to the temperature profiles and the standard deviation of the
temperature at the Y-cut cross section, the non-uniform temperature
inside chamber is found as the moving speed is larger than 0.01 m/s.
By reducing the heating faces to four, the standard deviation of the
temperature of the reaction chamber is under 1.4×10-3K with the range
of velocities between 0.0001 m/s and 1 m/s. The nature convective
boundary conditions are set at all boundaries while the chamber moves
between two heaters, the effects of various moving velocities of the
chamber on the temperature distributions are negligible at the assigned
time duration.
Abstract: Impact is one of very important subjects which always have been considered in mechanical science. Nature of impact is such that which makes its control a hard task. Therefore it is required to present the transfer of impact to other vulnerable part of a structure, when it is necessary, one of the best method of absorbing energy of impact, is by using Thin-walled tubes these tubes collapses under impact and with absorption of energy, it prevents the damage to other parts.Purpose of recent study is to survey the deformation and energy absorption of tubes with different type of cross section (rectangular or square) and with similar volumes, height, mean cross section thickness, and material under loading with different speeds. Lateral loading of tubes are quasi-static type and beside as numerical analysis, also experimental experiences has been performed to evaluate the accuracy of the results. Results from the surveys is indicates that in a same conditions which mentioned above, samples with square cross section ,absorb more energy compare to rectangular cross section, and also by increscent in speed of loading, energy absorption would be more.
Abstract: This paper focuses on the Mega-Sub Controlled
Structure Systems (MSCSS) performances and characteristics
regarding the new control principle contained in MSCSS subjected to
strong earthquake excitations. The adopted control scheme consists of
modulated sub-structures where the control action is achieved by
viscous dampers and sub-structure own configuration. The
elastic-plastic time history analysis under severe earthquake excitation
is analyzed base on the Finite Element Analysis Method (FEAM), and
some comparison results are also given in this paper. The result shows
that the MSCSS systems can remarkably reduce vibrations effects
more than the mega-sub structure (MSS). The study illustrates that the
improved MSCSS presents good seismic resistance ability even at 1.2g
and can absorb seismic energy in the structure, thus imply that
structural members cross section can be reduce and achieve to good
economic characteristics. Furthermore, the elasto-plastic analysis
demonstrates that the MSCSS is accurate enough regarding
international building evaluation and design codes. This paper also
shows that the elasto-plastic dynamic analysis method is a reasonable
and reliable analysis method for structures subjected to strong
earthquake excitations and that the computed results are more precise.
Abstract: The calculation of buckling length factor (K) for steel
frames columns is a major and governing processes to determine the
dimensions steel frame columns cross sections during design. The
buckling length of steel frames columns has a direct effect on the cost
(weight) of using cross section. A new formula is required to
determine buckling length factor (K) by simplified way. In this
research a new formula for buckling length factor (K) was established
to determine by accurate method for a limited interval of columns
ends rigidity (GA, GB). The new formula can be used ease to
evaluate the buckling length factor without needing to complicated
equations or difficult charts.
Abstract: Hardness of the widely used structural steel is of vital
importance since it may help in the determination of many
mechanical properties of a material under loading situations. In order
to obtain reliable information for design, properties homogeneity
should be validated. In the current study the hardness variation over
the different diameters of the same AISI 4140 bar is investigated.
Measurements were taken on the two faces of the stock at equally
spaced eight sectors and fifteen layers. Statistical and graphical
analysis are performed to asses the distribution of hardness
measurements over the specified area. Hardness measurements
showed some degree of dispersion with about ± 10% of its nominal
value provided by manufacturer. Hardness value is found to have a
slight decrease trend as the diameter is reduced. However, an
opposite behavior is noticed regarding the sequence of the sector
indicating a nonuniform distribution over the same area either on the
same face or considering the corresponding sector on the other face
(cross section) of the same material bar.
Abstract: This paper was to study the clothes dryer using waste
heat from a split type air conditioner with a capacity of 12,648 btu/h.
The drying chamber had a minimum cross section area with the size
of 0.5 x 1.0 m2. The chamber was constructed by sailcloth and was
inside folded with aluminium foil. Then, it was connected to the
condensing unit of an air conditioner. The experiment was carried out
in two aspects which were the clothes drying with and without
auxiliary fan unit. The results showed that the drying rate of clothes
in the chamber installed with and without auxiliary fan unit were
2.26 and 1.1 kg/h, respectively. In case of the chamber installed with
a auxiliary fan unit, the additional power of 0.011 kWh was
consumed and the drying rate was higher than that of clothes drying
without auxiliary fan unit. Without auxiliary fan unit installation, no
energy was required but there was a portion of hot air leaks away
through the punctured holes at the wall of the drying chamber, hence
the drying rate was dropped below. The drying rate of clothes drying
using waste heat was higher than natural indoor drying and
commercial dryer which their drying rate were 0.17 and 1.9 kg/h,
respectively. It was noted that the COP of the air conditioner did not
change during the operating of clothes drying.
Abstract: In this paper, a study on the applications of the
optimization and regression techniques for optimal calculation of
partial ratios of helical gearboxes with second-step double gear-sets
for minimal cross section dimension is introduced. From the condition
of the moment equilibrium of a mechanic system including three gear
units and their regular resistance condition, models for calculation of
the partial ratios of helical gearboxes with second-step double
gear-sets were given. Especially, by regression analysis, explicit
models for calculation of the partial ratios are introduced. These
models allow determining the partial ratios accurately and simply.
Abstract: In this work, are discussed two formulations of the boundary element method - BEM to perform linear bending analysis of plates reinforced by beams. Both formulations are based on the Kirchhoff's hypothesis and they are obtained from the reciprocity theorem applied to zoned plates, where each sub-region defines a beam or a slab. In the first model the problem values are defined along the interfaces and the external boundary. Then, in order to reduce the number of degrees of freedom kinematics hypothesis are assumed along the beam cross section, leading to a second formulation where the collocation points are defined along the beam skeleton, instead of being placed on interfaces. On these formulations no approximation of the generalized forces along the interface is required. Moreover, compatibility and equilibrium conditions along the interface are automatically imposed by the integral equation. Thus, these formulations require less approximation and the total number of the degree s of freedom is reduced. In the numerical examples are discussed the differences between these two BEM formulations, comparing as well the results to a well-known finite element code.
Abstract: Wind energy has been shown to be one of the most
viable sources of renewable energy. With current technology, the low
cost of wind energy is competitive with more conventional sources of
energy such as coal. Most blades available for commercial grade
wind turbines incorporate a straight span-wise profile and airfoil
shaped cross sections. These blades are found to be very efficient at
lower wind speeds in comparison to the potential energy that can be
extracted. However as the oncoming wind speed increases the
efficiency of the blades decreases as they approach a stall point. This
paper explores the possibility of increasing the efficiency of the
blades at higher wind speeds while maintaining efficiency at the
lower wind speeds. The design intends to maintain efficiency at
lower wind speeds by selecting the appropriate orientation and size
of the airfoil cross sections based on a low oncoming wind speed and
given constant rotation rate. The blades will be made more efficient
at higher wind speeds by implementing a swept blade profile.
Performance was investigated using the computational fluid
dynamics (CFD).
Abstract: For fire safety purposes, the fire resistance and the
structural behavior of reinforced concrete members are assessed to
satisfy specific fire performance criteria. The available prescribed
provisions are based on standard fire load. Under various fire
scenarios, engineers are in need of both heat transfer analysis and
structural analysis. For heat transfer analysis, the study proposed a
modified finite difference method to evaluate the temperature profile
within a cross section. The research conducted is limited to concrete
sections exposed to a fire on their one side. The method is based on
the energy conservation principle and a pre-determined power
function of the temperature profile. The power value of 2.7 is found
to be a suitable value for concrete sections. The temperature profiles
of the proposed method are only slightly deviate from those of the
experiment, the FEM and the FDM for various fire loads such as
ASTM E 119, ASTM 1529, BS EN 1991-1-2 and 550 oC. The
proposed method is useful to avoid incontinence of the large matrix
system of the typical finite difference method to solve the
temperature profile. Furthermore, design engineers can simply apply
the proposed method in regular spreadsheet software.
Abstract: The available data on the cross sections of electronimpact
excitation of krypton 5s and 5p configuration levels out of the
ground state are represented in convenient and compact form. The
results are obtained by regression through all known published data
related to this process.
Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.
Abstract: In this research a comparison between k-epsilon and
LES model for a deoiling hydrocyclone is conducted. Flow field of
hydrocyclone is obtained by three-dimensional simulations with
OpenFOAM code. Potential of prediction for both methods of this
complex swirl flow is discussed. Large eddy simulation method
results have more similarity to experiment and its results are
presented in figures from different hydrocyclone cross sections.
Abstract: Analysis of the elastic scattering of protons on 6,7Li
nuclei has been done in the framework of the optical model at the
beam energies up to 50 MeV. Differential cross sections for the 6,7Li +
p scattering were measured over the proton laboratory–energy range
from 400 to 1050 keV. The elastic scattering of 6,7Li+p data at
different proton incident energies have been analyzed using singlefolding
model. In each case the real potential obtained from the
folding model was supplemented by a phenomenological imaginary
potential, and during the fitting process the real potential was
normalized and the imaginary potential optimized. Normalization
factor NR is calculated in the range between 0.70 and 0.84.
Abstract: Cross sections of As radionuclides in the interaction of natGe with 14-30 MeV protons have been deduced by off-line y-ray spectroscopy to find optimal reaction channels leading to radiotracers for positron emission tomography. The experimental results were compared with the previous results and those estimated by the compound nucleus reaction model.