Abstract: In order to avoid the potentially devastating
consequences of global warming and climate change, the carbon
dioxide “CO2" emissions caused due to anthropogenic activities must
be reduced considerably. This paper presents the first study
examining the feasibility of carbon sequestration in construction and
demolition “C&D" waste. Experiments were carried out in a self
fabricated Batch Reactor at 40ºC, relative humidity of 50-70%, and
flow rate of CO2 at 10L/min for 1 hour for water-to-solids ratio of 0.2
to 1.2. The effect of surface area was found by comparing the
theoretical extent of carbonation of two different sieve sizes (0.3mm
and 2.36mm) of C&D waste. A 38.44% of the theoretical extent of
carbonation equating to 4% CO2 sequestration extent was obtained
for C&D waste sample for 0.3mm sieve size. Qualitative,
quantitative and morphological analyses were done to validate
carbonate formation using X-ray diffraction “X.R.D.," thermal
gravimetric analysis “T.G.A., “X-Ray Fluorescence Spectroscopy
“X.R.F.," and scanning electron microscopy “S.E.M".
Abstract: In the present study, an attempt was made to examine
the potential of aerobic mixed culture for decolourization of Remazol Black B dye in batch reactors. The effect of pH, temperature, inoculum, initial concentration of dye and initial concentration of
glucose was studied with an aim to determine the optimal conditions
required for maximum decolourization and degradation. The culture
exhibited maximum decolourization ability at pH between 7-8 and at
30°C. A 10% (v/v) inoculum and 1% (w/v) glucose concentration
were found to be the optimum for decolourization. A maximum of
98% decolourization was observed at 25 ppm initial concentration of
dye after 18 hours of incubation period. At higher dye concentration
of 300 ppm, the removal in colour was found to be 75% in 48 hours of incubation period. The results show that the enriched mixed culture from activated sludge has good potential in removal of Remazol Black B dye from wastewater under aerobic conditions.
Abstract: This paper describes the application of a model predictive controller to the problem of batch reactor temperature control. Although a great deal of work has been done to improve reactor throughput using batch sequence control, the control of the actual reactor temperature remains a difficult problem for many operators of these processes. Temperature control is important as many chemical reactions are sensitive to temperature for formation of desired products. This controller consist of two part (1) a nonlinear control method GLC (Global Linearizing Control) to create a linear model of system and (2) a Model predictive controller used to obtain optimal input control sequence. The temperature of reactor is tuned to track a predetermined temperature trajectory that applied to the batch reactor. To do so two input signals, electrical powers and the flow of coolant in the coil are used. Simulation results show that the proposed controller has a remarkable performance for tracking reference trajectory while at the same time it is robust against noise imposed to system output.
Abstract: The photochemical and photo-Fenton oxidation of 1,3-dichloro-2-propanol was performed in a batch reactor, at room temperature, using UV radiation, H2O2 as oxidant, and Fenton-s reagent. The effect of the oxidative agent-s initial concentration was investigated as well as the effect of the initial concentration of Fe(II) by following the target compound degradation, the total organic carbon removal and the chloride ion production. Also, from the kinetic analysis conducted and proposed reaction scheme it was deduced that the addition of Fe(II) significantly increases the production and the further oxidation of the chlorinated intermediates.
Abstract: Direct fermentation of 226 white rose tapioca stem to
ethanol by Fusarium oxysporum was studied in a batch reactor.
Fermentation of ethanol can be achieved by sequential pretreatment
using dilute acid and dilute alkali solutions using 100 mesh tapioca
stem particles. The quantitative effects of substrate concentration, pH
and temperature on ethanol concentration were optimized using a full
factorial central composite design experiment. The optimum process
conditions were then obtained using response surface methodology.
The quadratic model indicated that substrate concentration of 33g/l,
pH 5.52 and a temperature of 30.13oC were found to be optimum for
maximum ethanol concentration of 8.64g/l. The predicted optimum
process conditions obtained using response surface methodology was
verified through confirmatory experiments. Leudeking-piret model
was used to study the product formation kinetics for the production
of ethanol and the model parameters were evaluated using
experimental data.
Abstract: Electrochemical-oxidation of Reactive Black-5 (RB- 5) was conducted for degradation using DSA type Ti/RuO2-SnO2- Sb2O5 electrode. In the study, for electro-oxidation, electrode was indigenously fabricated in laboratory using titanium as substrate. This substrate was coated using different metal oxides RuO2, Sb2O5 and SnO2 by thermal decomposition method. Laboratory scale batch reactor was used for degradation and decolorization studies at pH 2, 7 and 11. Current density (50mA/cm2) and distance between electrodes (8mm) were kept constant for all experiments. Under identical conditions, removal of color, COD and TOC at initial pH 2 was 99.40%, 55% and 37% respectively for initial concentration of 100 mg/L RB-5. Surface morphology and composition of the fabricated electrode coatings were characterized using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) respectively. Coating microstructure was analyzed by X-ray diffraction (XRD). Results of this study further revealed that almost 90% of oxidation occurred within 5-10 minutes.
Abstract: In this work, statistical experimental design was
applied for the optimization of medium constituents for Gentamicin
production by Micromsonospora echinospora subs pallida (MTCC
708) in a batch reactor and the results are compared with the ANN
predicted values. By central composite design, 50 experiments are
carried out for five test variables: Starch, Soya bean meal, K2HPO4,
CaCO3 and FeSO4. The optimum condition was found to be: Starch
(8.9,g/L), Soya bean meal (3.3 g/L), K2HPO4 (0.8 g/L), CaCO3 (4
g/L) and FeSO4 (0.03 g/L). At these optimized conditions, the yield
of gentamicin was found to be 1020 mg/L. The R2 values were found
to be 1 for ANN training set, 0.9953 for ANN test set, and 0.9286 for
RSM.
Abstract: The desulfurization of coal using biological methods is an emerging technology. The biodesulfurization process uses the catalytic activity of chemolithotrophic acidpohiles in removing sulfur and pyrite from the coal. The present study was undertaken to examine the potential of Acidithiobacillus ferrooxidans in removing the pyritic sulfur and iron from high iron and sulfur containing US coal. The experiment was undertaken in 10 L batch stirred tank reactor having 10% pulp density of coal. The reactor was operated under mesophilic conditions and aerobic conditions were maintained by sparging the air into the reactor. After 35 days of experiment, about 64% of pyrite and 21% of pyritic sulfur was removed from the coal. The findings of the present study indicate that the biodesulfurization process does have potential in treating the high pyrite and sulfur containing coal. A good mass balance was also obtained with net loss of about 5% showing its feasibility for large scale application.
Abstract: The recovery of metal values and safe disposal of
spent catalyst is gaining interest due to both its hazardous nature and
increased regulation associated with disposal methods. Prior to the
recovery of the valuable metals, removal of entrained deposits limit
the diffusion of lixiviate resulting in low recovery of metals must be
taken into consideration. Therefore, petroleum refinery spent catalyst
was subjected to acetone washing and roasting at 500oC. The treated
samples were investigated for metals bioleaching using
Acidithiobacillus ferrooxidans in batch reactors and the leaching
efficiencies were compared. It was found out that acetone washed
spent catalysts results in better metal recovery compare to roasted
spent. About 83% Ni, 20% Al, 50% Mo and 73% V were leached
using the acetone washed spent catalyst. In both the cases, Ni, V and
Mo was high compared to Al.
Abstract: The conventional production of biodiesel from crude
palm oil which contains large amounts of free fatty acids in the
presence of a homogeneous base catalyst confronts the problems of
soap formation and very low yield of biodiesel. To overcome these
problems, free fatty acids must be esterified to their esters in the
presence of an acid catalyst prior to alkaline-catalyzed
transesterification. Sulfated metal oxides are a promising group of
catalysts due to their very high acidity. In this research, aluminadoped
sulfated tin oxide (SO4
2-/Al2O3-SnO2) catalysts were prepared
and used for esterification of free fatty acids in crude palm oil in a
batch reactor. The SO4
2-/Al2O3-SnO2 catalysts were prepared from
different Al precursors. The results showed that different Al
precursors gave different activities of the SO4
2-/Al2O3-SnO2 catalysts.
The esterification of free fatty acids in crude palm oil with methanol
in the presence of SO4
2-/Al2O3-SnO2 catalysts followed first-order
kinetics.
Abstract: A laboratory set-up was designed to survey the
effectiveness of UV/O3 advanced oxidation process (AOP) for the
removal of Carbaryl from polluted water in batch reactor. The study
was carried out by UV/O3 process for water samples containing 1 to
20 mg/L of Carbaryl in distilled water. Also the range of drinking
water resources adjusted in synthetic water and effects of contact
time, pH and Carbaryl concentration were studied. The residual
pesticide concentration was determined by applying high
performance liquid chromatography (HPLC). The results indicated
that increasing of retention time and pH, enhances pesticide removal
efficiency. The removal efficiency has been affected by pesticide
initial concentration. Samples with low pesticide concentration
showed a remarkable removal efficiency compared to the samples
with high pesticide concentration. AOP method showed the removal
efficiencies of 80% to 100%. Although process showed high
performance for removal of pesticide from water samples, this
process has different disadvantages including complication,
intolerability, difficulty of maintenance and equipmental and
structural requirements.
Abstract: The main objective of this study was to remove and recover Ni, Cu and Fe from a mixed metal system using sodium hypophosphite as a reducing agent and nickel powder as seeding material. The metal systems studied consisted of Ni-Cu, Ni-Fe and Ni-Cu-Fe solutions. A 5 L batch reactor was used to conduct experiments where 100 mg/l of each respective metal was used. It was found that the metals were reduced to their elemental form with removal efficiencies of over 80%. The removal efficiency decreased in the order Fe>Ni>Cu. The metal powder obtained contained between 97-99% Ni and was almost spherical and porous. Size enlargement by aggregation was the dominant particulate process.
Abstract: Hydrodesulfurization (HDS) of dibenzothiophene
(DBT) in a high pressure batch reactor was done at 320 °C on
CoMoS/Al2O3-B2O3 (4, 10, and 16 wt. % of Boria) using nhexadecane
as solvent, dimethyldisulfide (DMDS) in tetradecane as
sulfur agent, and stirring at 1000 rpm. The effects of boria were
investigated by using X-ray diffraction (XRD), Temperature
programmed desorption (TPD) of ammonia, and Brunauer-Emmet-
Teller (BET) experiments. The results showed that the catalyst
prepared with low boria content (4 wt. %) had HDS activity (in
pseudo first order kinetic constant basis) value ~1.45 times higher to
that of CoMoS/Al2O3 catalyst.
Abstract: The kinetics of palm oil catalytic cracking over
aluminum containing mesoporous silica Al-MCM-41 (5% Al) was
investigated in a batch autoclave reactor at the temperatures range of
573 – 673 K. The catalyst was prepared by using sol-gel technique
and has been characterized by nitrogen adsorption and x-ray
diffraction methods. Surface area of 1276 m2/g with average pore
diameter of 2.54 nm and pore volume of 0.811 cm3/g was obtained.
The experimental catalytic cracking runs were conducted using 50 g
of oil and 1 g of catalyst. The reaction pressure was recorded at
different time intervals and the data were analyzed using Levenberg-
Marquardt (LM) algorithm using polymath software. The results
show that the reaction order was found to be -1.5 and activation
energy of 3200 J/gmol.
Abstract: The main objective of this research was to investigate
the biosorption capacity for biofilms of sulphate reducing bacteria
(SRB) to remove heavy metals, such as Zn, Pb and Cd from
rainwater using laboratory-scale reactors containing mixed support
media. Evidence showed that biosorption had contributed to removal
of heavy metals including Zn, Pb and Cd in presence of SRB and
SRB were also found in the aqueous samples from reactors.
However, the SRB and specific families (Desulfobacteriaceae and
Desulfovibrionaceae) were found mainly in the biomass samples
taken from all reactors at the end of the experiment. EDX-analysis
of reactor solids at end of experiment showed that heavy metals Zn,
Pb and Cd had also accumulated in these precipitates.
Abstract: In this study a neural network (NN) was proposed to
predict the sorption of binary mixture of copper-cobalt ions into
clinoptilolite as ion-exchanger. The configuration of the
backpropagation neural network giving the smallest mean square
error was three-layer NN with tangent sigmoid transfer function at
hidden layer with 10 neurons, linear transfer function at output layer
and Levenberg-Marquardt backpropagation training algorithm.
Experiments have been carried out in the batch reactor to obtain
equilibrium data of the individual sorption and the mixture of coppercobalt
ions. The obtained modeling results have shown that the used
of neural network has better adjusted the equilibrium data of the
binary system when compared with the conventional sorption
isotherm models.
Abstract: Removal of PCP by a system combining
biodegradation by biofilm and adsorption was investigated here.
Three studies were conducted employing batch tests, sequencing
batch reactor (SBR) and continuous biofilm activated carbon
column reactor (BACCOR). The combination of biofilm-GAC
batch process removed about 30% more PCP than GAC adsorption
alone. For the SBR processes, both the suspended and attached
biomass could remove more than 90% of the PCP after
acclimatisation. BACCOR was able to remove more than 98% of
PCP-Na at concentrations ranging from 10 to 100 mg/L, at empty
bed contact time (EBCT) ranging from 0.75 to 4 hours. Pure and
mixed cultures from BACCOR were tested for use of PCP as sole
carbon and energy source under aerobic conditions. The isolates
were able to degrade up to 42% of PCP under aerobic conditions in
pure cultures. However, mixed cultures were found able to degrade
more than 99% PCP indicating interdependence of species.
Abstract: Extraction of lactic acid by emulsion liquid membrane technology (ELM) using n-trioctyl amine (TOA) in n-heptane as carrier within the organic membrane along with sodium carbonate as acceptor phase was optimized by using response surface methodology (RSM). A three level Box-Behnken design was employed for experimental design, analysis of the results and to depict the combined effect of five independent variables, vizlactic acid concentration in aqueous phase (cl), sodium carbonate concentration in stripping phase (cs), carrier concentration in membrane phase (ψ), treat ratio, and batch extraction time (τ)
with equal volume of organic and external aqueous phase on lactic acid extraction efficiency. The maximum lactic acid extraction efficiency (ηext) of 98.21%from aqueous phase in a batch reactor using ELM was found at the optimized values for test variables, cl, cs, ψ, and τ as 0.06 [M], 0.18 [M], 4.72 (%,v/v), 1.98 (v/v) and 13.36 min respectively.
Abstract: The complex hybrid and nonlinear nature of many processes that are met in practice causes problems with both structure modelling and parameter identification; therefore, obtaining a model that is suitable for MPC is often a difficult task. The basic idea of this paper is to present an identification method for a piecewise affine (PWA) model based on a fuzzy clustering algorithm. First we introduce the PWA model. Next, we tackle the identification method. We treat the fuzzy clustering algorithm, deal with the projections of the fuzzy clusters into the input space of the PWA model and explain the estimation of the parameters of the PWA model by means of a modified least-squares method. Furthermore, we verify the usability of the proposed identification approach on a hybrid nonlinear batch reactor example. The result suggest that the batch reactor can be efficiently identified and thus formulated as a PWA model, which can eventually be used for model predictive control purposes.