Abstract: Binder drainage test is widely used to set an upper
limit to the design binder content of porous asphalt. However, the
presence of high amount of fine particles in the drained binder may
affect the accuracy of the test result. This paper presents a study to
characterize the composition and particle size distribution of fine
particles accumulated in the drained binder. Fine aggregates and filler
in the drained binder were extracted using a suitable solvent. Then,
wet and dry sieve analysis was carried out to identify the actual
composition of the extracted fine aggregates and filler. From the
results, almost half of the drained binder consisted of fine aggregates
and this significantly affects the accuracy of the design binder content
of porous asphalt mix. This simple finding highlights the importance
of taking into account the presence of fine aggregates in the
calculation of drained binder.
Abstract: Asphalt surfaces are exposed to various weather
conditions and dynamic loading caused by passing trucks and
vehicles. In such situations, asphalt cement shows so different
rheological-mechanical behavior. If asphalt cement isn-t compatible
enough, asphalt layer will be damaged immediately and expensive
repairing procedures should be performed then. To overcome this
problem, researchers study on mechanical improved asphalt cement.
In this study, bentonite was used in order to modify bitumen
characteristics and the modified bitumen's characteristics were
investigated by asphalt cement tests. Then, the optimal bitumen
content in various compounds was determined and asphalt samples
with different contents of additives were prepared and tested. Results
show using this kind of additive not only has caused improvement in
bitumen mechanical properties, but also improvement in Marshall
Parameters was achieved.
Abstract: Utilization of waste material in asphalt pavement
would be beneficial in order to find an alternative solution to increase
service life of asphalt pavement and reduce environmental pollution
as well. One of these waste materials is Polyethylene Terephthalate
(PET) which is a type of polyester material and is produced in a large
extent. This research program is investigating the effects of adding
waste PET particles into the asphalt mixture with a maximum size of
2.36 mm. Different percentages of PET were added into the mixture
during dry process. Gap-graded mixture (SMA 14) and PG 80-100
asphalt binder have been used for this study. To evaluate PET
reinforced asphalt mixture different laboratory investigations have
been conducted on specimens. Marshall Stability test was carried
out. Besides, stiffness modulus test and indirect tensile fatigue test
were conducted on specimens at optimum asphalt content. It was
observed that in many cases PET reinforced SMA mixture had better
mechanical properties in comparison with control mixture.
Abstract: Concrete pavement has superior durability and longer
structural life than asphalt pavement. Concrete pavement requires
less maintenance compared to asphalt pavement which requires maintenance and major rehabilitation. Use of the concrete pavement
has been grown over the past decade in developing countries. Fibre reinforced concrete (FRC) has been successfully used in design of concrete pavement in past decade. In this research, the effect of fibre
volume fraction in modulus of rupture, load-deflection, equivalent flexural strength (fe,3) and the equivalent flexural strength ratio (Re,3)
has been used in different fibre volume fraction. Crimped-type flat
steel fibre of size 50 x 2.0 x 0.6 mm was used with 1.0%, 1.5% and 2.0% volume fraction. Beam specimens of size 500 x 100 x 100 mm were used for flexural as well as with JCI method for analysis flexural toughness, equivalent flexural strength. It was obtained as the 2% fibre volume fractions; reduce 45% of the concrete pavement
thickness.
Abstract: Waste lubricating oil re-refining adsorption process by
different adsorbent materials was investigated. Adsorbent materials
such as oil adsorbent, egg shale powder, date palm kernel powder,
and acid activated date palm kernel powder were used. The
adsorption process over fixed amount of adsorbent at ambient
conditions was investigated. The adsorption/extraction process was
able to deposit the asphaltenic and metallic contaminants from the
waste oil to lower values. It was found that the date palm kernel
powder with contact time of 4 h was able to give the best conditions
for treating the waste oil. The recovered solvent could be also reused.
It was also found that the activated bentonite gave the best
physical properties followed by the date palm kernel powder.
Abstract: As the resources for naturally occurring aggregates
diminished at an ever increasing rate, researchers are keen to utilize
recycled materials in road construction in harmony with sustainable
development. Steel slag, a waste product from the steel making
industry, is one of the recycled materials reported to exhibit great
potential to replace naturally occurring aggregates in asphalt
mixtures. This paper presents the resilient modulus properties of
steel slag asphalt mixtures subjected to short term oven ageing
(STOA). The resilient modulus test was carried out to evaluate the
stiffness of asphalt mixtures at 10ºC, 25ºC and 40ºC. Previous
studies showed that stiffness changes in asphalt mixture played an
important role in inflicting pavement distress particularly cracking
and rutting that are common at low and high temperatures
respectively. Temperature was found to significantly influence the
resilient modulus of asphalt mixes. The resilient modulus of the
asphalt specimens tested decreased by more than 90% when the test
temperature increased from 10°C to 40°C.
Abstract: Hot Mix Asphalt (HMA) is one of the most
commonest constructed asphalts in Iran and the quality control of
constructed roads with HMA have been always paid due attention by
researchers. The quality control of constructed roads with this
method is being usually carried out by measuring volumetric
parameters of HMA marshall samples. One of the important
parameters that has a critical role in changing these volumetric
parameters is “compaction temperature"; which as a result of its
changing, volumetric parameters of Marshall Samples and
subsequently constructed asphalt is encountered with variations. In
this study, considering the necessity of preservation of the
compaction temperature, the effect of various temperatures on Hot
Mix Asphalt (HMA) samples properties has been evaluated. As well,
to evaluate the effect of this parameter on different grading, two
different grading (Top coat index grading and binder index grading)
have been used and samples were compacted at 5 various
temperatures.
Abstract: In this work, the precipitation of asphaltene from a Malaysian light oil reservoir was studies. A series of experiments were designed and carried out to examine the effect of CO2 injection on asphaltene precipitation. Different pressures of injections were used in Dynamic flooding experiment in order to investigate the effect of pressure versus injection pore volume of CO2. These dynamic displacement tests simulate reservoir condition. Results show that by increasing the pore volume of injected gas asphaltene precipitation will increases, also rise in injection pressure causes less precipitation. Sandstone core plug was used to represent reservoir formation during displacement test; therefore it made it possible to study the effect of present of asphaltene on formation. It is found out that the precipitated asphaltene can reduce permeability and porosity which is not favorable during oil production.
Abstract: The dynamic or complex modulus test is considered
to be a mechanistically based laboratory test to reliably characterize
the strength and load-resistance of Hot-Mix Asphalt (HMA) mixes
used in the construction of roads. The most common observation is
that the data collected from these tests are often noisy and somewhat
non-sinusoidal. This hampers accurate analysis of the data to obtain
engineering insight. The goal of the work presented in this paper is to
develop and compare automated evolutionary computational
techniques to filter test noise in the collection of data for the HMA
complex modulus test. The results showed that the Covariance
Matrix Adaptation-Evolutionary Strategy (CMA-ES) approach is
computationally efficient for filtering data obtained from the HMA
complex modulus test.
Abstract: The mechanical properties of granular solids are
dependent on the flow of stresses from one particle to another
through inter-particle contact. Although some experimental methods
have been used to study the inter-particle contacts in the past,
preliminary work with these techniques indicated that they do not
have the necessary resolution to distinguish between those contacts
that transmit the load and those that do not, especially for systems
with a wide distribution of particle sizes. In this research, computer
simulations are used to study the nature and distribution of contacts
in a compact with wide particle size distribution, representative of
aggregate size distribution used in asphalt pavement construction.
The packing fraction, the mean number of contacts and the
distribution of contacts were studied for different scenarios. A
methodology to distinguish and compute the fraction of load-bearing
particles and the fraction of space-filling particles (particles that do
not transmit any force) is needed for further investigation.
Abstract: This study has applied the L16 orthogonal array of the
Taguchi method to determine the optimized polymeric
Nanocomposite asphalt binder. Three control factors are defined as
polypropylene plastomer (PP), styrene-butadiene-styrene elastomer
(SBS) and Nanoclay. Four level of concentration contents are
introduced for prepared asphalt binder samples. all samples were
prepared with 4.5% of bitumen 60/70 content. Compressive strength
tests were carried out for defining the optimized sample via
QUALITEK-4 software. SBS with 3%, PP with 5 % and Nanoclay
with 1.5% of concentrations are defined as the optimized
Nanocomposite asphalt binders. The confirmation compressive
strength and also softening point tests showed that modification of
asphalt binders with this method, improved the compressive strength
and softening points of asphalt binders up to 55%.
Abstract: This paper characterizes the effects of artificial short
term aging in the laboratory on the rheological properties of virgin
80/100 penetration grade asphalt binder. After several years in
service, asphalt mixture started to deteriorate due to aging. Aging is a
complex physico-chemical phenomenon that influences asphalt
binder rheological properties causing a deterioration in asphalt
mixture performance. To ascertain asphalt binder aging effects, the
virgin, artificially aged and extracted asphalt binder were tested via
the Rolling Thin film Oven (RTFO), Dynamic Shear Rheometer
(DSR) and Rotational Viscometer (RV). A comparative study
between laboratory and field aging conditions were also carried out.
The results showed that the specimens conditioned for 85 minutes
inside the RTFO was insufficient to simulate the actual short term
aging caused that took place in the field under Malaysian field
conditions
Abstract: One of the important factors of cracks on the asphalt
pavements is bitumen aging that associated with the loss of volatile
components and oxidation of asphalt binder. This paper is about
effect of Styrene-Butadiene-Styrene (SBS) polymer on asphalt aging
In order to decrease asphalt aging effects. For this purpose samples of
base bitumen and SBS modified bitumen aged according to the
rolling thin film oven test (RTFOT) and pressure aging vessel (PAV),
respectively. Properties of each sample were evaluated using Fourier
Transform Infrared (FTIR) spectroscopy, n-heptane precipitation,
viscosity test, softening point test and penetration test. FT-IR
Analysis, showed lower oxidation of SBS modified bitumen than
base bitumen, after aging.
Abstract: Road industry has challenged the prospect of ecoconstruction. Pavements may fit within the framework of sustainable development. Hence, research implements assessments of conventional pavements impacts on environment in use of life cycle approach. To meet global, and often national, targets on pollution control, newly introduced pavement designs are under study. This is the case of Cyprus demonstration, which occurred within EcoLanes project work. This alternative pavement differs on concrete layer reinforced with tire recycling product. Processing of post-consumer tires produces steel fibers improving strength capacity against cracking. Thus maintenance works are relevantly limited in comparison to flexible pavement. This enables to be more ecofriendly, referenced to current study outputs. More specific, proposed concrete pavement life cycle processes emits 15 % less air pollutants and consumes 28 % less embodied energy than those of the asphalt pavement. In addition there is also a reduction on costs by 0.06 %.
Abstract: Fatigue cracking continues to be the main challenges in
improving the performance of bituminous mixture pavements. The
purpose of this paper is to look at some aspects of the effects of fine
aggregate properties on the fatigue behaviour of hot mixture asphalt.
Two types of sand (quarry and mining sand) with two conventional
bitumen (PEN 50/60 & PEN 80/100) and four polymers modified
bitumen PMB (PM1_82, PM1_76, PM2_82 and PM2_76) were used.
Physical, chemical and mechanical tests were performed on the sands
to determine their effect when incorporated with a bituminous
mixture. According to the beam fatigue results, quarry sand that has
more angularity, rougher, higher shear strength and a higher
percentage of Aluminium oxide presented higher resistance to
fatigue. Also a PMB mixture gives better fatigue results than
conventional mixtures, this is due to the PMB having better viscosity
property than that of the conventional bitumen.
Abstract: In the Enhanced Oil Recovery (EOR) method, use of Carbon dioxide flooding whereby CO2 is injected into an oil reservoir to increase output when extracting oil resulted significant recovery worldwide. The carbon dioxide function as a pressurizing agent when mixed into the underground crude oil will reduce its viscosity and will enable a rapid oil flow. Despite the CO2’s advantage in the oil recovery, it may result to asphaltene precipitation a problem that will cause the reduction of oil produced from oil wells. In severe cases, asphaltene precipitation can cause costly blockages in oil pipes and machinery. This paper presents reviews of several studies done on mathematical modeling of asphaltene precipitation. The synthesized result from several researches done on this topic can be used as guide in order to better understand asphaltene precipitation. Likewise, this can be used as initial reference for students, and new researchers doing study on asphaltene precipitation.
Abstract: This study demonstrates the use of Class F fly ash in
combination with lime or lime kiln dust in the full depth reclamation
(FDR) of asphalt pavements. FDR, in the context of this paper, is a
process of pulverizing a predetermined amount of flexible pavement
that is structurally deficient, blending it with chemical additives and
water, and compacting it in place to construct a new stabilized base
course. Test sections of two structurally deficient asphalt pavements
were reclaimed using Class F fly ash in combination with lime and
lime kiln dust. In addition, control sections were constructed using
cement, cement and emulsion, lime kiln dust and emulsion, and mill
and fill. The service performance and structural behavior of the FDR
pavement test sections were monitored to determine how the fly ash
sections compared to other more traditional pavement rehabilitation
techniques. Service performance and structural behavior were
determined with the use of sensors embedded in the road and Falling
Weight Deflectometer (FWD) tests. Monitoring results of the FWD
tests conducted up to 2 years after reclamation show that the cement,
fly ash+LKD, and fly ash+lime sections exhibited two year resilient
modulus values comparable to open graded cement stabilized
aggregates (more than 750 ksi). The cement treatment resulted in a
significant increase in resilient modulus within 3 weeks of
construction and beyond this curing time, the stiffness increase was
slow. On the other hand, the fly ash+LKD and fly ash+lime test
sections indicated slower shorter-term increase in stiffness. The fly
ash+LKD and fly ash+lime section average resilient modulus values
at two years after construction were in excess of 800 ksi. Additional
longer-term testing data will be available from ongoing pavement
performance and environmental condition data collection at the two
pavement sites.