Abstract: In this work, the main problem considered is the
detection and the isolation of the actuator fault. A new formulation of
the linear system is generated to obtain the conditions of the actuator
fault diagnosis. The proposed method is based on the representation
of the actuator as a subsystem connected with the process system in
cascade manner. The designed formulation is generated to obtain the
conditions of the actuator fault detection and isolation. Detectability
conditions are expressed in terms of the invertibility notions. An
example and a comparative analysis with the classic formulation
illustrate the performances of such approach for simple actuator fault
diagnosis by using the linear model of nuclear reactor.
Abstract: This paper demonstrates the potential of applying PD-like fuzzy logic controller for active vibration control of piezoelectric Stewart platforms. Through simulation, the control authority of the piezo stack actuators for effectively damping the Stewart platform vibration can be evaluated for further implementation of the system. Each leg of the piezoelectric Stewart platform consists of a linear piezo stack actuator, a collocated velocity sensor, a collocated displacement sensor and flexible tips for the connections with the two end plates. The piezoelectric stack is modeled as a bar element and the electro-mechanical coupling property is simulated using Matlab/Simulink software. Then, the open loop and closed loop dynamic responses are performed for the system to characterize the effect of the control on the vibration of the piezoelectric Stewart platform. A significant improvement in the damping of the structure can be observed by using the PD-like fuzzy controller.
Abstract: Inconsistency in manual inspection is real because humans get tired after some time. Recent trends show that automatic inspection is more appealing for mass production inspections. In such as a case, a robot manipulator seems the best candidate to run a dynamic visual inspection. The purpose of this work is to estimate the optimum workspace where a robot manipulator would perform a visual inspection process onto a work piece where a camera is attached to the end effector. The pseudo codes for the planned path are derived from the number of tool transit points, the delay time at the transit points, the process cycle time, and the configuration space that the distance between the tool and the work piece. It is observed that express start and swift end are acceptable in a robot program because applicable works usually in existence during these moments. However, during the mid-range cycle, there are always practical tasks programmed to be executed. For that reason, it is acceptable to program the robot such as that speedy alteration of actuator displacement is avoided. A dynamic visual inspection system using a robot manipulator seems practical for a work piece with a complex shape.
Abstract: The present work deals with the optimal placement of piezoelectric actuators on a thin plate using Modified Control Matrix and Singular Value Decomposition (MCSVD) approach. The problem has been formulated using the finite element method using ten piezoelectric actuators on simply supported plate to suppress first six modes. The sizes of ten actuators are combined to outline one actuator by adding the ten columns of control matrix to form a column matrix. The singular value of column control matrix is considered as the fitness function and optimal positions of the actuators are obtained by maximizing it with GA. Vibration suppression has been studied for simply supported plate with piezoelectric patches in optimal positions using Linear Quadratic regulator) scheme. It is observed that MCSVD approach has given the position of patches adjacent to each-other, symmetric to the centre axis and given greater vibration suppression than other previously published results on SVD.
Abstract: An enhanced ad-hoc on-demand distance vector routing (E-AODV) protocol for control system applications in wireless sensor and actuator networks (WSANs) is proposed. Our routing algorithm is designed by considering both wireless network communication and the control system aspects. Control system error and network delay are the main selection criteria in our routing protocol. The control and communication performance is evaluated on multi-hop IEEE 802.15.4 networks for building-temperature control systems. The Gilbert-Elliott error model is employed to simulate packet loss in wireless networks. The simulation results demonstrate that the E-AODV routing approach can significantly improve the communication performance better than an original AODV routing under various packet loss rates. However, the control performance result by our approach is not much improved compared with the AODV routing solution.
Abstract: In recent years, Japanese society has been aging, engendering a labor shortage of young workers. Robots are therefore expected to perform tasks such as rehabilitation, nursing elderly people, and day-to-day work support for elderly people. The pneumatic balloon actuator is a rubber artificial muscle developed for use in a robot hand in such environments. This actuator has a long stroke and a high power-to-weight ratio compared with the present pneumatic artificial muscle. Moreover, the dynamic characteristics of this actuator resemble those of human muscle. This study evaluated characteristics of force control of balloon actuator using a predictive functional control (PFC) system with disturbance observer. The predictive functional control is a model-based predictive control (MPC) scheme that predicts the future outputs of the actual plants over the prediction horizon and computes the control effort over the control horizon at every sampling instance. For this study, a 1-link finger system using a pneumatic balloon actuator is developed. Then experiments of PFC control with disturbance observer are performed. These experiments demonstrate the feasibility of its control of a pneumatic balloon actuator for a robot hand.
Abstract: An innovative design for intelligent Chemical Mechanical Polishing (CMP) system is proposed and verified by experiments in this report. On-line measurement and real-time feedback are integrated to eliminate the shortcomings of traditional approaches, e.g., the batch-to-batch discrepancy of required polishing time, over consumption of chemical slurry, and non-uniformity across the wafer. The major advantage of the proposed method is that the finish of local surface roughness can be consistent, no matter where the inner-ring region or outer-ring region is concerned. Secondly, it is able to eliminate the Edge effect. Conventionally, the interfacial induced stress near the wafer edge is generally much higher than that near the wafer center. At last, by using the proposed intelligent chemical mechanical polishing strategy, the cost of the entire machining cycle can be much reduced while the quality of the finished goods certainly upgraded.
Abstract: This paper describes an underactuated robot hand operated by low-power actuators. It can grasp objects of various shapes using easy operations. This hand is suitable for use as a lightweight prosthetic hand that can grasp various objects using few input channels. To realize operations using a low-power actuator, a cross section deformation spring is proposed. The design procedure of the underactuated robot finger is proposed to realize an adaptive grasping movement. The validity of this mechanism and design procedure are confirmed through an object grasping experiment. Results demonstrate the effectiveness of across section deformation spring in reducing the actuator power. Moreover, adaptive grasping movement is realized by an easy operation.
Abstract: A challenged control problem is when the
performance is pushed to the limit. The state-derivative feedback
control strategy directly uses acceleration information for feedback
and state estimation. The derivative part is concerned with the rateof-
change of the error with time. If the measured variable approaches
the set point rapidly, then the actuator is backed off early to allow it
to coast to the required level. Derivative action makes a control
system behave much more intelligently. A sensor measures the
variable to be controlled and the measured in formation is fed back to
the controller to influence the controlled variable. A high gain
problem can be also formulated for proportional plus derivative
feedback transformation. Using MATLAB Simulink dynamic
simulation tool this paper examines a system with a proportional plus
derivative feedback and presents an automatic implementation of
finding an acceptable controlled system. Using feedback
transformations the system is transformed into another system.
Abstract: Automotive suspension system is important part of car
comfort and safety. In this article automotive active suspension with
linear motor as actuator is designed using H-infinity control. This
paper is focused on comparison of different controller designed for
quart, half or full-car model (and always used for “full" car). Special
attention is placed on energy demand of the whole system. Each
controller configuration is simulated and then verified on the
hydraulic quarter car test bed.
Abstract: The aim of this paper is to present a new
three-dimensional proportional-pursuit coupled (PP) guidance law to
track highly maneuverable aircraft. Utilizing a 3-D polar coordinate frame, the PP guidance law is formed by collecting proportional
navigation guidance in Z-R plane and pursuit guidance in X-Y plane.
Feedback linearization control method to solve the guidance
accelerations is used to implement PP guidance. In order to
compensate the actuator time delay, the time delay compensated
version of PP guidance law (CPP) was derived and proved the
effectiveness of modifying the problem of high acceleration in the final
phase of pursuit guidance and improving the weak robustness of
proportional navigation. The simulation results for intercepting Max G
turn situation show that the proposed proportional-pursuit coupled
guidance law guidance law with actuator delay compensation (CPP)
possesses satisfactory robustness and performance.
Abstract: This paper aims to present the design, fabrication and test of a novel piezoelectric actuated, check-valves embedded micropump having the advantages of miniature size, light weight and low power consumption. This device is designed to pump gases and liquids with the capability of performing the self-priming and bubble-tolerant work mode by maximizing the stroke volume of the membrane as well as the compression ratio via minimization of the dead volume of the micropump chamber and channel. By experiment apparatus setup, we can get the real-time values of the flow rate of micropump, the displacement of the piezoelectric actuator and the deformation of the check valve, simultaneously. The micropump with check valve 0.4 mm in thickness obtained higher output performance under the sinusoidal waveform of 120 Vpp. The micropump achieved the maximum pumping rates of 42.2 ml/min and back pressure of 14.0 kPa at the corresponding frequency of 28 and 20 Hz. The presented micropump is able to pump gases with a pumping rate of 196 ml/min at operating frequencies of 280 Hz under the sinusoidal waveform of 120 Vpp.
Abstract: Continuously variable transmission (CVT) is a type of
automatic transmission that can change the gear ratio to any arbitrary
setting within the limits. The most common type of CVT operates on
a pulley system that allows an infinite variability between highest and
lowest gears with no discrete steps. However, the current CVT
system with hydraulic actuation method suffers from the power loss.
It needs continuous force for the pulley to clamp the belt and hold the
torque resulting in large amount of energy consumption. This study
focused on the development of an electromechanical actuated control
CVT to eliminate the problem that faced by the existing CVT. It is
conducted with several steps; computing and selecting the
appropriate sizing for stroke length, lead screw system and etc. From
the visual observation it was found that the CVT system of this
research is satisfactory.
Abstract: A robust control approach is proposed for a high speed manipulator using a hybrid computed torque control approach in the state space. The high-speed manipulator is driven by permanent magnet dc motors to track a trajectory in the joint space in the presence of disturbances. Tracking problem is analyzed in the state space where the completed models are considered for actuators. The proposed control approach can guarantee the stability and a satisfactory tracking performance. A two-link elbow manipulator driven by electrical actuators is simulated and results are shown to satisfy conditions under technical specifications.
Abstract: This paper features the modeling and design of a
Robust Decentralized Fast Output Sampling (RDFOS) Feedback
control technique for the active vibration control of a smart flexible
multimodel Euler-Bernoulli cantilever beams for a multivariable
(MIMO) case by retaining the first 6 vibratory modes. The beam
structure is modeled in state space form using the concept of
piezoelectric theory, the Euler-Bernoulli beam theory and the Finite
Element Method (FEM) technique by dividing the beam into 4 finite
elements and placing the piezoelectric sensor / actuator at two finite
element locations (positions 2 and 4) as collocated pairs, i.e., as
surface mounted sensor / actuator, thus giving rise to a multivariable
model of the smart structure plant with two inputs and two outputs.
Five such multivariable models are obtained by varying the
dimensions (aspect ratios) of the aluminium beam. Using model
order reduction technique, the reduced order model of the higher
order system is obtained based on dominant Eigen value retention
and the Davison technique. RDFOS feedback controllers are
designed for the above 5 multivariable-multimodel plant. The closed
loop responses with the RDFOS feedback gain and the magnitudes of
the control input are obtained and the performance of the proposed
multimodel smart structure system is evaluated for vibration control.
Abstract: An approach for experimental measurement of the
dynamic characteristics of linear electromagnet actuators is
presented. It uses accelerometer sensor to register the armature
acceleration. The velocity and displacement of the moving parts can
be obtained by integration of the acceleration results. The armature
movement of permanent magnet linear actuator is acquired using this
technique. The results are analyzed and the performance of the
supposed approach is compared with the most commonly used
experimental setup where the displacement of the armature vs. time
is measured instead of its acceleration.
Abstract: We present a BeeBot, Binus Multi-client Intelligent Telepresence Robot, a custom-build robot system specifically designed for teleconference with multiple person using omni directional actuator. The robot is controlled using a computer networks, so the manager/supervisor can direct the robot to the intended person to start a discussion/inspection. People tracking and autonomous navigation are intelligent features of this robot. We build a web application for controlling the multi-client telepresence robot and open-source teleconference system used. Experimental result presented and we evaluated its performance.
Abstract: This paper deals with the design of a periodic output
feedback controller for a flexible beam structure modeled with
Timoshenko beam theory, Finite Element Method, State space
methods and embedded piezoelectrics concept. The first 3 modes are
considered in modeling the beam. The main objective of this work is
to control the vibrations of the beam when subjected to an external
force. Shear piezoelectric sensors and actuators are embedded into
the top and bottom layers of a flexible aluminum beam structure, thus
making it intelligent and self-adaptive. The composite beam is
divided into 5 finite elements and the control actuator is placed at
finite element position 1, whereas the sensor is varied from position 2
to 5, i.e., from the nearby fixed end to the free end. 4 state space
SISO models are thus developed. Periodic Output Feedback (POF)
Controllers are designed for the 4 SISO models of the same plant to
control the flexural vibrations. The effect of placing the sensor at
different locations on the beam is observed and the performance of
the controller is evaluated for vibration control. Conclusions are
finally drawn.
Abstract: The aerodynamic stall control of a baseline 13-percent
thick NASA GA(W)-2 airfoil using a synthetic jet actuator (SJA) is
presented in this paper. Unsteady Reynolds-averaged Navier-Stokes
equations are solved on a hybrid grid using a commercial software to
simulate the effects of a synthetic jet actuator located at 13% of the
chord from the leading edge at a Reynolds number Re = 2.1x106 and
incidence angles from 16 to 22 degrees. The experimental data for the
pressure distribution at Re = 3x106 and aerodynamic coefficients at
Re = 2.1x106 (angle of attack varied from -16 to 22 degrees) without
SJA is compared with the computational fluid dynamic (CFD)
simulation as a baseline validation. A good agreement of the CFD
simulations is obtained for aerodynamic coefficients and pressure
distribution.
A working SJA has been integrated with the baseline airfoil and
initial focus is on the aerodynamic stall control at angles of attack
from 16 to 22 degrees. The results show a noticeable improvement in
the aerodynamic performance with increase in lift and decrease in
drag at these post stall regimes.
Abstract: This research proposes the state of art on how to control or find the trajectory paths of the RRP robot when the prismatic joint is malfunction. According to this situation, the minimum energy of the dynamic optimization is applied. The RRP robot or similar systems have been used in many areas such as fire fighter truck, laboratory equipment and military truck for example a rocket launcher. In order to keep on task that assigned, the trajectory paths must be computed. Here, the open loop control is applied and the result of an example show the reasonable solution which can be applied to the controllable system.