Abstract: This paper addresses the problem of asymptotic tracking
control of a linear parabolic partial differential equation with indomain
point actuation. As the considered model is a non-standard
partial differential equation, we firstly developed a map that allows
transforming this problem into a standard boundary control problem
to which existing infinite-dimensional system control methods can
be applied. Then, a combination of energy multiplier and differential
flatness methods is used to design an asymptotic tracking controller.
This control scheme consists of stabilizing state-feedback derived
from the energy multiplier method and feed-forward control based
on the flatness property of the system. This approach represents
a systematic procedure to design tracking control laws for a class
of partial differential equations with in-domain point actuation. The
applicability and system performance are assessed by simulation
studies.
Abstract: The effect of different combinations of response
feedback on the performance of active control system on nonlinear
frames has been studied in this paper. To this end different feedback
combinations including displacement, velocity, acceleration and full
response feedback have been utilized in controlling the response of
an eight story bilinear hysteretic frame which has been subjected to a
white noise excitation and controlled by eight actuators which could
fully control the frame. For active control of nonlinear frame
Newmark nonlinear instantaneous optimal control algorithm has been
used which a diagonal matrix has been selected for weighting
matrices in performance index. For optimal design of active control
system while the objective has been to reduce the maximum drift to
below the yielding level, Distributed Genetic Algorithm (DGA) has
been used to determine the proper set of weighting matrices. The
criteria to assess the effect of each combination of response feedback
have been the minimum required control force to reduce the
maximum drift to below the yielding drift. The results of numerical
simulation show that the performance of active control system is
dependent on the type of response feedback where the velocity
feedback is more effective in designing optimal control system in
comparison with displacement and acceleration feedback. Also using
full feedback of response in controller design leads to minimum
control force amongst other combinations. Also the distributed
genetic algorithm shows acceptable convergence speed in solving the
optimization problem of designing active control systems.
Abstract: Active vibration control is an important problem in
structures. The objective of active vibration control is to reduce the vibrations of a system by automatic modification of the system-s
structural response. In this paper, the modeling and design of a fast
output sampling feedback controller for a smart flexible beam system embedded with shear sensors and actuators for SISO system using
Timoshenko beam theory is proposed. FEM theory, Timoshenko beam theory and the state space techniques are used to model the
aluminum cantilever beam. For the SISO case, the beam is divided into 5 finite elements and the control actuator is placed at finite
element position 1, whereas the sensor is varied from position 2 to 5, i.e., from the nearby fixed end to the free end. Controllers are
designed using FOS method and the performance of the designed FOS controller is evaluated for vibration control for 4 SISO models
of the same plant. The effect of placing the sensor at different locations on the beam is observed and the performance of the
controller is evaluated for vibration control. Some of the limitations of the Euler-Bernoulli theory such as the neglection of shear and
axial displacement are being considered here, thus giving rise to an accurate beam model. Embedded shear sensors and actuators have
been considered in this paper instead of the surface mounted sensors
and actuators for vibration suppression because of lot of advantages. In controlling the vibration modes, the first three dominant modes of
vibration of the system are considered.
Abstract: This paper addresses the design of predictive
networked controller with adaptation of a communication delay. The
networked control system contains random delays from sensor to
controller and from controller to actuator. The proposed predictive
controller includes an adaptation loop which decreases the influence
of communication delay on the control performance. Also, the
predictive controller contains a filter which improves the robustness
of the control system. The performance of the proposed adaptive
predictive controller is demonstrated by simulation results in
comparison with PI controller and predictive controller with constant
delay.
Abstract: In this paper, a bond graph dynamic model for a valvecontrolled
hydraulic cylinder has been developed. A simplified bond
graph model of the inter-actuator interactions in a multi-cylinder
hydraulic system has also been presented. The overall bond graph
model of a valve-controlled hydraulic cylinder was developed by
combining the bond graph sub-models of the pump, spool valve and
the actuator using junction structures. Causality was then assigned
in order to obtain a computational model which could be simulated.
The causal bond graph model of the hydraulic cylinder was verified
by comparing the open loop state responses to those of an ODE
model which had been developed in literature based on the same
assumptions. The results were found to correlate very well both
in the shape of the curves, magnitude and the response times,
thus indicating that the developed model represents the hydraulic
dynamics of a valve-controlled cylinder. A simplified model for interactuator
interaction was presented by connecting an effort source with
constant pump pressure to the zero-junction from which the cylinders
in a multi-cylinder system are supplied with a constant pressure from
the pump. On simulating the state responses of the developed model
under different situations of cylinder operations, indicated that such
a simple model can be used to predict the inter-actuator interactions.
Abstract: In this paper, we show that the association of the PI
regulators for the speed and stator currents with a control strategy
using the linearization by state feedback for an induction machine
without speed sensor, and with an adaptation of the rotor resistance.
The rotor speed is estimated by using the model reference adaptive
system approach (MRAS). This method consists of using two
models: The first is the reference model and the second is an
adjustable one in which two components of the stator flux, obtained
from the measurement of the currents and stator voltages are
estimated. The estimated rotor speed is then obtained by canceling
the difference between stator-flux of the reference model and those
of the adjustable one. Satisfactory results of simulation are obtained
and discussed in this paper to highlight the proposed approach.
Abstract: This paper presents a synthetic jet air blower actuated
by PZT for air blowing for air-breathing micro PEM fuel cell. The
several factors to affect the performance of air-breathing PEM fuel cell
such as air flow rate, opening ratio and cathode open type in the
cathode side were studied. Especially, an air flow rate is critical
condition to improve its performance. In this paper, we developed a
synthetic jet air blower to supply a high stoichiometric air flow. The
synthetic jet mechanism is a zero mass flux device that converts
electrical energy into the momentum. The synthetic jet actuation is
usually generated by a traditional PZT actuator, which consists of a
small cylindrical cavity, in/outlet channel and PZT diaphragms. The
flow rate of the fabricated synthetic jet air blower was 400cc/min at
550Hz and its power consumption was very low under 0.3W. The
proposed air-breathing PEM fuel cell which installed synthetic jet air
blower was higher performance and stability during continuous
operation than the air-breathing fuel cell without auxiliary device to
supply the air. The results showed that the maximum power density
was 188mW/cm2 at 400mA/cm2. This maximum power density and
durability were improved more than 40% and 20%, respectively.
Abstract: This paper describes a newly designed decentralized
nonlinear control strategy to control a robot manipulator. Based on the
concept of the nonlinear state feedback theory and decentralized
concept is developed to improve the drawbacks in previous works
concerned with complicate intelligent control and low cost effective
sensor. The control methodology is derived in the sense of Lyapunov
theorem so that the stability of the control system is guaranteed. The
decentralized algorithm does not require other joint angle and velocity
information. Individual Joint controller is implemented using a digital
processor with nearly actuator to make it possible to achieve good
dynamics and modular. Computer simulation result has been
conducted to validate the effectiveness of the proposed control scheme
under the occurrence of possible uncertainties and different reference
trajectories. The merit of the proposed control system is indicated in
comparison with a classical control system.
Abstract: A novel adaptive fuzzy trajectory tracking algorithm of Stewart platform based motion platform is proposed to compensate path deviation and degradation of controller-s performance due to actuator torque limit. The algorithm can be divided into two parts: the real-time trajectory shaping part and the joint space adaptive fuzzy controller part. For a reference trajectory in task space whenever any of the actuators is saturated, the desired acceleration of the reference trajectory is modified on-line by using dynamic model of motion platform. Meanwhile an additional action with respect to the difference between the nominal and modified trajectories is utilized in the non-saturated region of actuators to reduce the path error. Using modified trajectory as input, the joint space controller incorporates compute torque controller, leg velocity observer and fuzzy disturbance observer with saturation compensation. It can ensure stability and tracking performance of controller in present of external disturbance and position only measurement. Simulation results verify the effectiveness of proposed control scheme.
Abstract: This paper presents the design, development and characterization of contractile water jet thruster (CWJT) for mini underwater robot. Instead of electric motor, this CWJT utilizes the Ionic Polymer Metal Composite (IPMC) as the actuator to generate the water jet. The main focus of this paper is to analyze the conceptual design of the proposed CWJT which would determine the thrust force value, jet flow behavior and actuator’s stress. Those thrust force and jet flow studies were carried out using Matlab/Simscape simulation software. The actuator stress had been analyzed using COSMOS simulation software. The results showed that there was no significant change for jet velocity at variable cross sectional nozzle area. However, a significant change was detected for jet velocity at different nozzle cross sectional area ratio which was up to 37%. The generated thrust force has proportional relation to the nozzle cross sectional area.
Abstract: We propose an integral tracking control method for a piezoelectric actuator system. The proposed method achieves the output tracking without requiring any hysteresis observer or schemes to compensate the hysteresis effect. With the proposed control law, the system is converted into the standard singularly perturbed model. Using Tikhonov-s theorem, we guarantee that the tracking error can be reduced to arbitrarily small bound. A numerical example is given to illustrate the effectiveness of our proposed method.
Abstract: One of the robust fault detection filter (RFDF)
designing method is based on sliding-mode theory. The main purpose
of our study is to introduce an innovative simplified reference
residual model generator to formulate the RFDF as a sliding-mode
observer without any manipulation package or transformation matrix,
through which the generated residual signals can be evaluated. So the
proposed design is more explicit and requires less design parameters
in comparison with approaches requiring changing coordinates. To
the best author's knowledge, this is the first time that the sliding
mode technique is applied to detect actuator and sensor faults in a
real boiler. The designing procedure is proposed in a drum boiler in
Synvendska Kraft AB Plant in Malmo, Sweden as a multivariable
and strongly coupled system. It is demonstrated that both sensor and
actuator faults can robustly be detected. Also sensor faults can be
diagnosed and isolated through this method.
Abstract: In this study, a double-sided linear switched reluctance
motor (LSRM) drive was investigated as an alternative actuator for
vertical linear transportation applications such as a linear elevator
door, hospital and subway doors which move linearly and where
accurate position control and rapid response is requested. A prototype
sliding elevator door that is focused on a home elevator with LSRMs
is designed. The motor has 6/4 poles, 3 phases, 8A, 24V, 250 W and
250 N pull forces. Air gap between rotor and translator poles of the
designed motor and phase coil-s ideal inductance profile are obtained
in compliance with the geometric dimensions. Operation and
switching sections as motor and generator has been determined from
the inductance profile.
Abstract: The paper considers a novel modular and intrinsically safe redundant robotic system with biologically inspired actuators (pneumatic artificial muscles and rubber bellows actuators). Similarly to the biological systems, the stiffness of the internal parallel modules, representing 2 DOF joints in the serial robotic chains, is controlled by co-activation of opposing redundant actuator groups in the null-space of the module Jacobian, without influencing the actual robot position. The decoupled position/stiffness control allows the realization of variable joint stiffness according to different force-displacement relationships. The variable joint stiffness, as well as limited pneumatic muscle/bellows force ability, ensures internal system safety that is crucial for development of human-friendly robots intended for human-robot collaboration. The initial experiments with the system prototype demonstrate the capabilities of independently, simultaneously controlling both joint (Cartesian) motion and joint stiffness. The paper also presents the possible industrial applications of snake-like robots built using the new modules.
Abstract: The most common type of controller being used in
the industry is PI(D) controller which has been used since 1945 and
is still being widely used due to its efficiency and simplicity. In
most cases, the PI(D) controller was tuned without taking into
consideration of the effect of actuator saturation. In real processes,
the most common actuator which is valve will act as constraint and
restrict the controller output. Since the controller is not designed to
encounter saturation, the process may windup and consequently
resulted in large oscillation or may become unstable. Usually, an
antiwindup compensator is added to the feedback control loop to
reduce the deterioration effect of integral windup. This research
aims to specifically control processes with constraints. The
proposed method was applied to two different types of food
processes, which are blending and spray drying. Simulations were
done using MATLAB and the performances of the proposed
method were compared with other conventional methods. The
proposed technique was able to control the processes and avoid
saturation such that no anti windup compensator is needed.
Abstract: In this study, we used shape memory alloys as
actuators to build a biomorphic robot which can imitate the motion of
an earthworm. The robot can be used to explore in a narrow space.
Therefore we chose shape memory alloys as actuators. Because of the
small deformation of a wire shape memory alloy, spiral shape memory
alloys are selected and installed both on the X axis and Y axis (each
axis having two shape memory alloys) to enable the biomorphic robot
to do reciprocating motion. By the mechanism we designed, the robot
can increase the distance as it moves in a duty cycle. In addition, two
shape memory alloys are added to the robot head for controlling right
and left turns. By sending pulses through the I/O card from the
controller, the signals are then amplified by a driver to heat the shape
memory alloys in order to make the SMA shrink to pull the mechanism
to move.
Abstract: The objective of this paper is to develop a neural
network-based residual generator to detect the fault in the actuators
for a specific communication satellite in its attitude control system
(ACS). First, a dynamic multilayer perceptron network with dynamic
neurons is used, those neurons correspond a second order linear
Infinite Impulse Response (IIR) filter and a nonlinear activation
function with adjustable parameters. Second, the parameters from the
network are adjusted to minimize a performance index specified by
the output estimated error, with the given input-output data collected
from the specific ACS. Then, the proposed dynamic neural network
is trained and applied for detecting the faults injected to the wheel,
which is the main actuator in the normal mode for the communication
satellite. Then the performance and capabilities of the proposed
network were tested and compared with a conventional model-based
observer residual, showing the differences between these two
methods, and indicating the benefit of the proposed algorithm to
know the real status of the momentum wheel. Finally, the application
of the methods in a satellite ground station is discussed.
Abstract: In this paper an algorithm based on the adaptive
neuro-fuzzy controller is provided to enhance the tipover stability of
mobile manipulators when they are subjected to predefined
trajectories for the end-effector and the vehicle. The controller
creates proper configurations for the manipulator to prevent the robot
from being overturned. The optimal configuration and thus the most
favorable control are obtained through soft computing approaches
including a combination of genetic algorithm, neural networks, and
fuzzy logic. The proposed algorithm, in this paper, is that a look-up
table is designed by employing the obtained values from the genetic
algorithm in order to minimize the performance index and by using
this data base, rule bases are designed for the ANFIS controller and
will be exerted on the actuators to enhance the tipover stability of the
mobile manipulator. A numerical example is presented to
demonstrate the effectiveness of the proposed algorithm.
Abstract: This paper presents an authoring tool which makes a
user easily and intuitively design vibrotactile sensation. A mobile
hardware platform powered by ANDROID, a multi-purpose haptic
driver and a linear resonance actuator are used to implement the
system of the presented authoring tool. The tool allows users to easily
and simply create a vibrotactile sensation by drawing vibrotactile
images and to feel the sensation by rubbing drawn images on the touch
screen of a mobile device. The tool supports a graphical interface for
designing, editing and playing vibrotactile images as well as a
pre-defined file format for save and open.
Abstract: We proposed the use of a Toda-Rayleigh ring as a
central pattern generator (CPG) for controlling hexapodal robots. We
show that the ring composed of six Toda-Rayleigh units coupled to
the limb actuators reproduces the most common hexapodal gaits. We
provide an electrical circuit implementation of the CPG and test our
theoretical results obtaining fixed gaits. Then we propose a method
of incorporation of the actuator (motor) dynamics in the CPG. With
this approach we close the loop CPG – environment – CPG, thus
obtaining a decentralized model for the leg control that does not
require higher level intervention to the CPG during locomotion in
a nonhomogeneous environments. The gaits generated by the novel
CPG are not fixed, but adapt to the current robot bahvior.