Abstract: The objective of this study was to evaluate the
physical and chemical characteristics of Serra da Estrela cheese and
compare these results with those of the sensory analysis. For the
study were taken six samples of Serra da Estrela cheese produced
with 6 different ecotypes of thistle in a dairy situated in Penalva do
Castelo. The chemical properties evaluated were moisture content,
protein, fat, ash, chloride and pH; the physical properties studied
were color and texture; and finally a sensory evaluation was
undertaken. The results showed moisture varying in the range 40-
48%, protein in the range 15-20%, fat between 41-45%, ash between
3.9-5.0% and chlorides varying from 1.2 to 3.0%. The pH varied
from 4.8 to 5.4. The textural properties revealed that the crust
hardness is relatively low (maximum 7.3 N), although greater than
flesh firmness (maximum 1.7 N), and also that these cheeses are in
fact soft paste type, with measurable stickiness and intense
adhesiveness. The color analysis showed that the crust is relatively
light (L* over 50), and with a predominant yellow coloration (b*
around 20 or over) although with a slight greenish tone (a* negative).
The results of the sensory analysis did not show great variability for
most of the attributes measured, although some differences were
found in attributes such as crust thickness, crust uniformity, and
creamy flesh.
Abstract: Surface modification and functionalization has been
an important tool for scientists in order to open new frontiers in
nanoscience and nanotechnology. Desired surface characteristics for
the intended applications can be achieved with surface
functionalization.
In this work, the effect of water soluble ligands on the adsorption
capabilities of silver nanoparticles onto AC which was synthesized
from German beech wood was investigated. Sodium borohydride
(NaBH4) and polyvinyl alcohol (PVA) were used as the ligands.
Silver nanoparticles with different surface coatings have average
sizes range from 10 to 13 nm. They were synthesized in aqueous
media by reducing Ag (I) ion in the presence of ligands. These
particles displayed adsorption tendencies towards AC when they
were mixed together and shaken in distilled water.
Silver nanoparticles (NaBH4-AgNPs) reduced and stabilized by
NaBH4 adsorbed onto AC with a homogenous dispersion of
aggregates with sizes in the range of 100-400 nm. Beside, silver
nanoparticles, which were prepared in the presence of both NaBH4
and PVA (NaBH4/PVA-Ag NPs), demonstrated that NaBH4/PVA-Ag
NPs adsorbed and dispersed homogenously but, they aggregated with
larger sizes on the AC surface (range from 300 to 600 nm). In
addition, desorption resistance of Ag nanoparticles were investigated
in distilled water. According to the results AgNPs were not desorbed
on the AC surface in distilled water.
Abstract: Natural hydrocarbon seepage has helped petroleum
exploration as a direct indicator of gas and/or oil subsurface
accumulations. Surface macro-seeps are generally an indication of a
fault in an active Petroleum Seepage System belonging to a Total
Petroleum System. This paper describes a case study in which
multiple analytical techniques were used to identify and characterize
trace petroleum-related hydrocarbons and other volatile organic
compounds in groundwater samples collected from Sousse aquifer
(Central Tunisia). The analytical techniques used for analyses of
water samples included gas chromatography-mass spectrometry (GCMS),
capillary GC with flame-ionization detection, Compound
Specific Isotope Analysis, Rock Eval Pyrolysis. The objective of the
study was to confirm the presence of gasoline and other petroleum
products or other volatile organic pollutants in those samples in order
to assess the respective implication of each of the potentially
responsible parties to the contamination of the aquifer. In addition,
the degree of contamination at different depths in the aquifer was also
of interest. The oil and gas seeps have been investigated using
biomarker and stable carbon isotope analyses to perform oil-oil and
oil-source rock correlations. The seepage gases are characterized by
high CH4 content, very low δ13CCH4 values (-71,9 ‰) and high
C1/C1–5 ratios (0.95–1.0), light deuterium–hydrogen isotope ratios (-
198 ‰) and light δ13CC2 and δ13CCO2 values (-23,8‰ and-23,8‰
respectively) indicating a thermogenic origin with the contribution of
the biogenic gas. An organic geochemistry study was carried out on
the more ten oil seep samples. This study includes light hydrocarbon
and biomarkers analyses (hopanes, steranes, n-alkanes, acyclic
isoprenoids, and aromatic steroids) using GC and GC-MS. The
studied samples show at least two distinct families, suggesting two
different types of crude oil origins: the first oil seeps appears to be
highly mature, showing evidence of chemical and/or biological
degradation and was derived from a clay-rich source rock deposited
in suboxic conditions. It has been sourced mainly by the lower
Fahdene (Albian) source rocks. The second oil seeps was derived
from a carbonate-rich source rock deposited in anoxic conditions,
well correlated with the Bahloul (Cenomanian-Turonian) source rock.
Abstract: The composite pavement system considered in this
paper is composed of a functional surface layer, a fiber reinforced
asphalt middle layer and a fiber reinforced lean concrete base layer.
The mix design of the fiber reinforced lean concrete corresponds to the
mix composition of conventional lean concrete but reinforced by
fibers. The quasi-absence of research on the durability or long-term
performances (fatigue, creep, etc.) of such mix design stresses the
necessity to evaluate experimentally the long-term characteristics of
this layer composition. This study tests the creep characteristics as one
of the long-term characteristics of the fiber reinforced lean concrete
layer for composite pavement using a new creep device. The test
results reveal that the lean concrete mixed with fiber reinforcement
and fly ash develops smaller creep than the conventional lean
concrete. The results of the application of the CEB-FIP prediction
equation indicate that a modified creep prediction equation should be
developed to fit with the new mix design of the layer.
Abstract: Flow blockages referring to the increase in flow are
being considered as a vital equipment for marine current energy
conversion. However, the shape of these devices will result in
extracted energy under the operation. The present work investigates
the effect of two configurations of a grating, convergent and
divergent that located upstream, to the water flow velocity. The flow
characteristics are studied by Computational Fluid Dynamic
simulation by using the ANSYS Fluent solver for these specified
arrangements of the grating. The results indicate that distinguished
characteristics of flow velocity between “convergent” and
“divergent” grating placements is up to 10% in confined conditions.
Furthermore, the velocity in case of convergent grating is higher
than that of divergent grating.
Abstract: Chitosan has been an attractive biopolymer for
decades, but its processability is lowered by its poor solubility,
especially in physiological pH values. Freeze concentrated reactions
of chitosan with several organic acids including acrylic, citraconic,
itaconic, and maleic acid revealed improved solubility and
morphological properties. Solubility traits were assessed with a
modified ninhydrin test. Chitosan derivatives were characterized by
ATR-FTIR and morphological characteristics were determined by
SEM. This study is a unique approach to chemically modify chitosan
to enhance water solubility.
Abstract: This research aimed to study the characteristics of a
community in the social, economic and cultural context. This
research used interviews and surveys of the members in the Patthana
Soi Ranongklang community, Dusit District, Bangkok. The results
are as follows: In terms of overall conditions and characteristics, the
Patthana Soi Ranongklang community is located on the property of
the Treasury Department. 50 years ago, the location of this
community consisted of paddy fields with limited convenience in
terms of transportation. Rama V Road was only a small narrow road
accessed only by three-wheelers there were no buses. The majority of
community members moved in from Mak Khawan Rangsan Bridge.
Thus, most community members were either workers or government
officials as they were routers not the owners of the land. Therefore,
there were no primary occupations within the 7 acres of this
community. The development of the community started in 1981. At
present, the community is continuously being developed and
modernization is rapidly flowing in. One of the reasons was because
the main roads were widened, especially Rama V Road that allows
more convenient transportation, leading to heightened citizens’
convenience. In terms of the economy and society, Rama V Road
causes the research to find out the development and expansion of
change in the conditions of the area and buildings. Some buildings
were improved and changed along the time, as well as the
development of new facilities that caused the community members to
continually become more materialistic. In the community, it has well
organized and managed jobs to each part of community members,
and areas were improved to allow the new buildings and apartments.
The trend of jobs became more varied, in terms of both jobs at home,
such as workers, merchandizing and small own businesses, and the
community jobs outside, which became much more convenient to car
drivers as they got used to the narrow roads inside the community.
The location of the community next to Rama V Road also allows
assistance from government agencies to reach the community with
ease. Moreover, the welfare of the community was well taken care of
by the community committee. In terms of education, the research
found that there are two schools: Wat Pracharabuedham School and
Wat Noi Noppakun School that are providing education within the
community. The majority in the community have received Bachelor
degrees. In areas of culture, the research found that the culture,
traditions and beliefs of people in the community were mainly
transferred from the old community: the majorities are Buddhists, so
especially beliefs in Buddhism; the main reason for this is because
the old community was situated near Wat Makut Kasattriyaram.
Therefore, the community members have always had Buddhist
temples as the centre of the community. Later years, more citizens
moved along culture in and bring traditions and beliefs with them.
The community members also took part in building a Dharma hall
named Wat Duang Jai which is 72 year old.
Abstract: Future mobile networks following 5th generation will
be characterized by one thousand times higher gains in capacity;
connections for at least one hundred billion devices; user experience
capable of extremely low latency and response times. To be close to
the capacity requirements and higher reliability, advanced
technologies have been studied, such as multiple connectivity, small
cell enhancement, heterogeneous networking, and advanced
interference and mobility management. This paper is focused on the
multiple connectivity in heterogeneous cellular networks. We
investigate the performance of coverage and user throughput in several
deployment scenarios. Using the stochastic geometry approach, the
SINR distributions and the coverage probabilities are derived in case
of dual connection. Also, to compare the user throughput enhancement
among the deployment scenarios, we calculate the spectral efficiency
and discuss our results.
Abstract: The elastic period has a primary role in the seismic
assessment of buildings. Reliable calculations and/or estimates of the
fundamental frequency of a building and its site are essential during
analysis and design process. Various code formulas based on
empirical data are generally used to estimate the fundamental
frequency of a structure. For existing structures, in addition to code
formulas and available analytical tools such as modal analyses,
various methods of testing including ambient and forced vibration
testing procedures may be used to determine dynamic characteristics.
In this study, the dynamic properties of the 32 buildings located in
the Madinah of Saudi Arabia were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Ambient vibration measurements of buildings have been
analyzed and the fundamental longitudinal and transverse periods for
all tested buildings are presented. The fundamental mode of vibration
has been compared in plots with codes formulae (Saudi Building
Code, EC8, and UBC1997). The results indicate that measured
periods of existing buildings are shorter than that given by most
empirical code formulas. Recommendations are given based on the
common design and construction practice in Madinah city.
Abstract: A nanocrystalline thin film of ZnSe was successfully
electrodeposited on copper substrate using a non-aqueous solution
and subsequently annealed in air at 400°C. XRD analysis indicates
the polycrystalline deposit of (111) plane in both the cases. The
sharpness of the peak increases due to annealing of the film and
average grain size increases to 20 nm to 27nm. SEM photograph
indicate that grains are uniform and densely distributed over the
surface. Annealing increases the average grain size by 20%. The EDS
spectroscopy shows the ratio of Zn & Se is 1.1 in case of annealed
film. AFM analysis indicates the average roughness of the film
reduces from 181nm to 165nm due to annealing of the film. The
bandgap also decreases from 2.71eV to 2.62eV.
Abstract: The main objective of aircraft aerodynamics is to
enhance the aerodynamic characteristics and maneuverability of the
aircraft. This enhancement includes the reduction in drag and stall
phenomenon. The airfoil which contains dimples will have
comparatively less drag than the plain airfoil. Introducing dimples on
the aircraft wing will create turbulence by creating vortices which
delays the boundary layer separation resulting in decrease of pressure
drag and also increase in the angle of stall. In addition, wake
reduction leads to reduction in acoustic emission. The overall
objective of this paper is to improve the aircraft maneuverability by
delaying the flow separation point at stall and thereby reducing the
drag by applying the dimple effect over the aircraft wing. This project
includes both computational and experimental analysis of dimple
effect on aircraft wing, using NACA 0018 airfoil. Dimple shapes of
Semi-sphere, hexagon, cylinder, square are selected for the analysis;
airfoil is tested under the inlet velocity of 30m/s and 60m/s at
different angle of attack (5˚, 10˚, 15˚, 20˚, and 25˚). This analysis
favors the dimple effect by increasing L/D ratio and thereby
providing the maximum aerodynamic efficiency, which provides the
enhanced performance for the aircraft.
Abstract: Potato (Solanum tuberosum L.) is one of the major
vegetable crops that are grown world –wide because of its economic
importance. This experiment investigated the effect of local sands
(River Base, Al-Ekader and Karbala) on number and total weight of
minitubers. Statistical analysis revealed that there were no significant
differences among sand cultures in number of stem/plant, chlorophyll
index and tubers dry weight. River Base sand had the highest plant
height (74.9 cm), leaf number/plant number (39.3), leaf area (84.4
dcm2⁄plant), dry weight/plant (26.31), tubers number/plant (8.5),
tubers weight/plant (635.53 gm) and potato tuber yields/trove (28.60
kg), whereas the Karbala sand had lower performance. All the
characters had positive and significant correlation with yields except
the traits number of stem and tuber dry weight.
Abstract: Ti6Al4V alloy is highly used in the automotive and
aerospace industry due to its good machining characteristics. Micro
EDM drilling is commonly used to drill micro hole on extremely hard
material with very high depth to diameter ratio. In this study, the
parameters of micro-electrical discharge machining (EDM) in drilling
of Ti6Al4V alloy is optimized for higher machining accuracy with
less hole-dilation and hole taper ratio. The micro-EDM machining
parameters includes, peak current and pulse on time. Fuzzy analysis
was developed to evaluate the machining accuracy. The analysis
shows that hole-dilation and hole-taper ratio are increased with the
increasing of peak current and pulse on time. However, the surface
quality deteriorates as the peak current and pulse on time increase.
The combination that gives the optimum result for hole dilation is
medium peak current and short pulse on time. Meanwhile, the
optimum result for hole taper ratio is low peak current and short pulse
on time.
Abstract: Established objective and subjective preconditions for
entrepreneurship, forming the business organically related whole, are
the necessary condition of successful entrepreneurial activities.
Objective preconditions for entrepreneurship are developed by
market economy that should stimulate entrepreneurship by allowing
the use of economic opportunities for all those who want to do
business in respective field while providing guarantees to all owners
and creating a stable business environment for entrepreneurs.
Subjective preconditions of entrepreneurship are formed primarily by
personal characteristics of the entrepreneur. These are his properties,
abilities, skills, physiological and psychological preconditions which
may be inherited, inborn or sequentially developed and obtained
during his life on the basis of education and influences of
surrounding environment. The paper is dealing with issues of
objective and subjective preconditions for entrepreneurship and
provides their analysis in view of the current situation in Slovakia. It
presents risks of the business environment in Slovakia that the Slovak
managers considered the most significant in 2014 and defines the
dominant attributes of the entrepreneur in the current business
environment in Slovakia.
Abstract: The aim of this work is to build a model based on
tissue characterization that is able to discriminate pathological and
non-pathological regions from three-phasic CT images. With our
research and based on a feature selection in different phases, we are
trying to design a neural network system with an optimal neuron
number in a hidden layer. Our approach consists of three steps:
feature selection, feature reduction, and classification. For each
region of interest (ROI), 6 distinct sets of texture features are
extracted such as: first order histogram parameters, absolute gradient,
run-length matrix, co-occurrence matrix, autoregressive model, and
wavelet, for a total of 270 texture features. When analyzing more
phases, we show that the injection of liquid cause changes to the high
relevant features in each region. Our results demonstrate that for
detecting HCC tumor phase 3 is the best one in most of the features
that we apply to the classification algorithm. The percentage of
detection between pathology and healthy classes, according to our
method, relates to first order histogram parameters with accuracy of
85% in phase 1, 95% in phase 2, and 95% in phase 3.
Abstract: At present, the cascade PID control is widely used to
control the superheating temperature (main steam temperature). As
Main Steam Temperature has the characteristics of large inertia, large
time-delay and time varying, etc., conventional PID control strategy
cannot achieve good control performance. In order to overcome the
bad performance and deficiencies of main steam temperature control
system, Model Free Adaptive Control (MFAC) - P cascade control
system is proposed in this paper. By substituting MFAC in PID of the
main control loop of the main steam temperature control, it can
overcome time delays, non-linearity, disturbance and time variation.
Abstract: Living today in turbulent business environment forces
companies to distinguish from each other, securing sustainable
competitive growth and competitive advantage. The best possible
solution is to invest (effort and financial resources) within
companies’ different practices of human resource management
(HRM), more specifically in employees’ knowledge, skills and
abilities. Applying this approach companies will create enviable level
of human capital securing its economic growth. Employees become
human capital for their employers at the moment when they
contribute with their own knowledge and abilities in creating material
and non-material value of the company. The main aim of this
research is to explore the relations between human capital
investments and business excellence of Croatian companies.
Furthermore, the differences in the level of human capital
investments with regard to several companies’ characteristics (e.g.
size of the company, ownership and type of the industry) are
investigated.
Abstract: The Cone Penetration Test (CPT) is a common in-situ
test which generally investigates a much greater volume of soil more
quickly than possible from sampling and laboratory tests. Therefore,
it has the potential to realize both cost savings and assessment of soil
properties rapidly and continuously. The principle objective of this
paper is to demonstrate the feasibility and efficiency of using
artificial neural networks (ANNs) to predict the soil angle of internal
friction (Φ) and the soil modulus of elasticity (E) from CPT results
considering the uncertainties and non-linearities of the soil. In
addition, ANNs are used to study the influence of different
parameters and recommend which parameters should be included as
input parameters to improve the prediction. Neural networks discover
relationships in the input data sets through the iterative presentation
of the data and intrinsic mapping characteristics of neural topologies.
General Regression Neural Network (GRNN) is one of the powerful
neural network architectures which is utilized in this study. A large
amount of field and experimental data including CPT results, plate
load tests, direct shear box, grain size distribution and calculated data
of overburden pressure was obtained from a large project in the
United Arab Emirates. This data was used for the training and the
validation of the neural network. A comparison was made between
the obtained results from the ANN's approach, and some common
traditional correlations that predict Φ and E from CPT results with
respect to the actual results of the collected data. The results show
that the ANN is a very powerful tool. Very good agreement was
obtained between estimated results from ANN and actual measured
results with comparison to other correlations available in the
literature. The study recommends some easily available parameters
that should be included in the estimation of the soil properties to
improve the prediction models. It is shown that the use of friction
ration in the estimation of Φ and the use of fines content in the
estimation of E considerable improve the prediction models.
Abstract: In this research (using induction furnace process)
nodular iron with three different percentages of copper (residual,
0.5% and 1,2%) was obtained. Chemical analysis was performed by
mass spectrometry and microstructures were characterized by Optical
Microscopy (ASTM E3) and Scanning Electron Microscopy (SEM).
The study of mechanical behavior was carried out in a mechanical
test machine (ASTM E8) and a Pin on disk tribometer (ASTM G99)
was used to assess wear resistance. It is observed that the dissolution
of copper in crystal lattice increases the pearlite structure improving
the wear and hardness behavior, but producing a contrary effect on
the energy absorption.
Abstract: The decision-making process is theoretically clearly
defined. Generally, it includes the problem identification and
analysis, data gathering, goals and criteria setting, alternatives
development and optimal alternative choice and its implementation.
In practice however, various modifications of the theoretical
decision-making process can occur. The managers can consider some
of the phases to be too complicated or unfeasible and thus they do not
carry them out and conversely some of the steps can be
overestimated.
The aim of the paper is to reveal and characterize the perception of
the individual phases of decision-making process by the managers.
The research is concerned with managers in the military environment
– commanders. Quantitative survey is focused cross-sectionally in the
individual levels of management of the Ministry of Defence of the
Czech Republic. On the total number of 135 respondents the analysis
focuses on which of the decision-making process phases are
problematic or not carried out in practice and which are again
perceived to be the easiest. Then it is examined the reasons of the
findings.