Abstract: Catalytic combustion of methane is imperative due to
stability of methane at low temperature. Methane (CH4), therefore,
remains unconverted in vehicle exhausts thereby causing greenhouse
gas GHG emission problem. In this study, heterogeneous catalysts of
palladium with bio-char (2 wt% Pd/Bc) and Al2O3 (2wt% Pd/ Al2O3)
supports were prepared by incipient wetness impregnation and then
subsequently tested for catalytic combustion of CH4. Support-porous
heterogeneous catalytic combustion (HCC) material were selected
based on factors such as surface area, porosity, thermal stability,
thermal conductivity, reactivity with reactants or products, chemical
stability, catalytic activity, and catalyst life. Sustainable and
renewable support-material of bio-mass char derived from palm shell
waste material was compared with those from the conventional
support-porous materials. Kinetic rate of reaction was determined for
combustion of methane on Palladium (Pd) based catalyst with Al2O3
support and bio-char (Bc). Material characterization was done using
TGA, SEM, and BET surface area. The performance test was
accomplished using tubular quartz reactor with gas mixture ratio of
3% methane and 97% air. The methane porous-HCC conversion was
carried out using online gas analyzer connected to the reactor that
performed porous-HCC. BET surface area for prepared 2 wt% Pd/Bc
is smaller than prepared 2wt% Pd/ Al2O3 due to its low porosity
between particles. The order of catalyst activity based on kinetic rate
on reaction of catalysts in low temperature was 2wt%
Pd/Bc>calcined 2wt% Pd/ Al2O3> 2wt% Pd/ Al2O3>calcined 2wt%
Pd/Bc. Hence agro waste material can successfully be utilized as an
inexpensive catalyst support material for enhanced CH4 catalytic
combustion.
Abstract: This article discusses ways to implement a
differentiated approach to developing academic motivation for
mathematical studies which relies on defining the primary structural
characteristics of motivation. The following characteristics are
considered: features of realization of cognitive activity, meaningmaking
characteristics, level of generalization and consistency of
knowledge acquired by personal experience. The assessment of the
present level of individual student understanding of each component
of academic motivation is the basis for defining the relevant
educational strategy for its further development.
Abstract: This paper presents circuit models to analyze the
conducted susceptibility of multiconductor shielded cables in
frequency domains using Branin’s method, which is referred to as the
method of characteristics. These models, which can be used directly
in the time and frequency domains, take into account the presence of
both the transfer impedance and admittance. The conducted
susceptibility is studied by using an injection current on the cable
shield as the source. Two examples are studied; a coaxial shielded
cable and shielded cables with two parallel wires (i.e., twinax cables).
This shield has an asymmetry (one slot on the side). Results obtained
by these models are in good agreement with those obtained by other
methods.
Abstract: The dissimilar joint between aluminum/titanium
alloys (Al 6082 and Ti G2) were successfully achieved by CO2 laser
welding with a single pass and without filler material using the
overlap joint design. Laser welding parameters ranges combinations
were experimentally determined using Taguchi approach with the
objective of producing welded joint with acceptable welding profile
and high quality of mechanical properties. In this study a joining of
dissimilar Al 6082 / Ti G2 was resulted in three distinct regions
fusion area in the weldment. These regions are studied in terms of its
microstructural characteristics and microhardness which are directly
affecting the welding quality.
The weld metal was mainly composed of martensite alpha prime.
In two different metals in the two different sides of joint HAZ, grain
growth was detected. The microhardness of the joint distribution also
has shown microhardness increasing in the HAZ of two base metals
and a varying microhardness in fusion zone.
Abstract: Semiconductor crystals smaller than about 10 nm,
known as quantum dots, have properties that differ from large
samples, including a band gap that becomes larger for smaller
particles. These properties create several applications for quantum
dots. In this paper new shapes of quantum dot arrays are used to
enhance the photo physical properties of gold nano-particles. This
paper presents a study of the effect of nano-particles shape, array, and
size on their absorption characteristics.
Abstract: We are facing serious problems related to long-term
depopulation and an aging society with a falling birth rate in Japan. In
this situation, we are suffering from a shortfall in human resources as
well as a shortage of workforce in rural regions. In addition, we are
struggling with a protracted economic slump and excess concentration
of population in the Tokyo Metropolitan area. It is an urgent national
issue to consider how to live in this country and what kind of structure
of society and administration policy is needed. It is necessary to clarify
people’s desire for their way of living and social assistance to be
provided. The aim of this study is to clarify the characteristics of
regional issues and the degree of their seriousness in local
municipalities of Japan. We conducted a questionnaire survey about
regional agenda in all local municipalities in Japan. We obtained
responses concerning the degree of seriousness of regional issues and
degree of importance of policies. Based on the data gathered from the
survey, it is apparent that many local municipalities are facing an
aging population and declining population. We constructed a model to
analyze factors for declining population. Using the model, it was
clarified that a population’s age structure, job opportunities and
income level affect the decline of population. In addition, we showed
the way of the evaluation of state of local municipality.
Abstract: Thin-walled elements with a matrix set on a base of
high-valuable Portland cement with dispersed reinforcement from
alkali-resistant glass fibres are used in a range of applications as
claddings of buildings and infrastructure constructions as well as
various architectural elements of residential buildings.
Even though their elementary thickness and therefore total weight
is quite low, architects and building companies demand on even
further decreasing of the bulk density of these fibre-cement elements
for the reason of loading elimination of connected superstructures
and easier assembling in demand conditions.
By the means of various kinds of light-weight aggregates it is
possible to achieve light-weighing of these composite elements.
From the range of possible fillers with different material properties
granulated expanded glass worked the best.
By the means of laboratory testing an effect of two fillers based on
expanded glass on the fibre reinforced cement composite was
verified.
Practical applicability was tested in the production of commonly
manufactured glass fibre reinforced concrete elements, such as
channels for electrical cable deposition, products for urban equipment
and especially various cladding elements.
Even though these are not structural elements, it is necessary to
evaluate also strength characteristics and resistance to environment
for their durability in certain applications.
Abstract: Bir El Djir is an important coastal township in Oran
department, located at 450 Km far away from Algiers on northwest of
Algeria. In this coastal area, the urban sprawl is one of the main
problems that reduce the limited highly fertile land. So, using the
remote sensing and GIS technologies have shown their great
capabilities to solve many earth resources issues.
The aim of this study is to produce land use and cover map for the
studied area at varied periods to monitor possible changes that may
occurred, particularly in the urban areas and subsequently predict
likely changes. For this, two spatial images SPOT and Landsat
satellites from 1987 and 2014 respectively were used to assess the
changes of urban expansion and encroachment during this period
with photo-interpretation and GIS approach.
The results revealed that the town of Bir El Djir has shown a
highest growth rate in the period 1987-2014 which is 1201.5 hectares
in terms of area. These expansions largely concern the new real estate
constructions falling within the social and promotional housing
programs launched by the government.
The most urban expansion is characterized by the new
construction in the form of spontaneous or peripheral precarious
habitat, but also unstructured slums settled especially in the
southeastern part of town.
Abstract: Enterococci are important inhabitants of the animal
intestine and are widely used in probiotic products. A probiotic strain
is expected to possess several desirable properties in order to exert
beneficial effects. Therefore, the objective of this study was to
isolate, characterize and identify Enterococcus sp. from chicken cecal
and fecal samples to determine potential probiotic properties.
Enterococci were isolated from chicken ceca and feces of thirty three
clinically healthy chickens from a local farm. In vitro studies were
performed to assess antibacterial activity of the isolated LAB (using
agar well diffusion and cell free supernatant broth technique against
Salmonella enterica serotype Enteritidis), survival in acidic
conditions, resistance to bile salts, and their survival during simulated
gastric juice conditions at pH 2.5. Isolates were identified by
biochemical carbohydrate fermentation patterns using an API 50
CHL kit and API ZYM kits and by sequenced 16S rDNA. An isolate
belonging to E. faecium species exhibited inhibitory effect against S.
enteritidis. This isolate producing a clear zone as large as 10.30 mm
or greater and was able to grow in the coculture medium and at the
same time, inhibited the growth S. enteritidis. In addition, E. faecium
exhibited significant resistance under highly acidic conditions at pH
2.5 for 8 h and survived well in bile salt at 0.2% for 24 h and showing
ability to survive in the presence of simulated gastric juice at pH 2.5.
Based on these results, E. faecium isolate fulfills some of the criteria
to be considered as a probiotic strain and therefore, could be used as a
feed additive with good potential for controlling S. Enteritidis in
chickens. However, in vivo studies are needed to determine the safety
of the strain.
Abstract: This work deals with parameter identification of
permanent magnet motors, a class of ac motor which is particularly
important in industrial automation due to characteristics like
applications high performance, are very attractive for applications
with limited space and reducing the need to eliminate because they
have reduced size and volume and can operate in a wide speed range,
without independent ventilation. By using experimental data and
genetic algorithm we have been able to extract values for both the
motor inductance and the electromechanical coupling constant, which
are then compared to measured and/or expected values.
Abstract: The thermal behavior of a large-scale, phase change material (PCM) enhanced building envelope system was studied in regard to the need for pre-fabricated construction in subtropical regions. The proposed large-scale envelope consists of a reinforced aluminum skin, insulation core, phase change material and reinforced gypsum board. The PCM impact on an energy efficiency of an enveloped room was resolved by validation of the EnergyPlus numerical scheme and optimization of a smart material location in the core. The PCM location was optimized by a minimization method of a cooling energy demand. It has been shown that there is good agreement between the test and simulation results. The optimal location of the PCM layer in Hong Kong summer conditions has been then recomputed for core thicknesses of 40, 60 and 80 mm. A non-dimensional value of the optimal PCM location was obtained to be same for all the studied cases and the considered external and internal conditions.
Abstract: Fungal mutant strains have produced cellulase and
xylanase enzymes, and have induced high hydrolysis with enhanced
of rice straw. The mutants were obtained by exposing Penicillium
strain to UV-light treatments. Screening and selection after treatment
with UV-light were carried out using cellulolytic and xylanolytic
clear zones method to select the hypercellulolytic and
hyperxylanolytic mutants. These mutants were evaluated for their
cellulase and xylanase enzyme production as well as their abilities for
biodegradation of rice straw. The mutant 12 UV/1 produced 306.21%
and 209.91% cellulase and xylanase, respectively, as compared with
the original wild type strain. This mutant showed high capacity of
rice straw degradation. The effectiveness of tested mutant strain and
that of wild strain was compared in relation to enhancing the
composting process of rice straw and animal manures mixture. The
results obtained showed that the compost product of inoculated
mixture with mutant strain (12 UV/1) was the best compared to the
wild strain and un-inoculated mixture. Analysis of the composted
materials showed that the characteristics of the produced compost
were close to those of the high quality standard compost. The results
obtained in the present work suggest that the combination between
rice straw and animal manure could be used for enhancing the
composting process of rice straw and particularly when applied with
fungal decomposer accelerating the composting process.
Abstract: This paper analyzes the political and economic issues
that people with disabilities face related to globalization; how people
with disabilities have been adapting globalization and surviving under
worldwide competition system. It explains that economic
globalization exacerbates inequality and deprivation of people with
disabilities. The rising tide of neo-liberal welfare policies emphasized
efficiency, downsized social expenditure for people with disabilities,
excluded people with disabilities against labor market, and shifted
them from welfare system to nothing. However, there have been
people with disabilities' political responses to globalization, which are
characterized by a global network of people with disabilities as well as
participation to global governance. Their resistance can be seen as an
attempt to tackle the problems that economic globalization has
produced. It is necessary paradigm shift of disability policy from
dependency represented by disability benefits to independency
represented by labor market policies for people with disabilities.
Abstract: The purpose of this study is to investigate the kinematic
characteristics and differences of the snatch barbell trajectory of 53 kg
class female weight lifters. We take the 2014 Taiwan College Cup
players as examples, and tend to make kinematic applications through
the proven weightlifting barbell track system. The competition videos
are taken by consumer camcorder with a tripod which set up at the side
of the lifter. The results will be discussed in three parts, the first part is
various lifting phase, the second part is the compare lifting between
success and unsuccessful, and the third part is to compare the
outstanding player with the general. Conclusion through the barbell
can be used to observe the trajectories of our players lifting the usual
process cannot be observed in the presence of malfunction or habits, so
that the coach can find the problem and guide the players more
accurately. Our system can be applied in practice and competition to
increase the resilience of the lifter on the field.
Abstract: Poly vinyl acetate (PVA)-based titania (TiO2)–carbon
nanotube composite nanofibers (PVA-TCCNs) with various
PVA-to-solvent ratios and PVA-based TiO2 composite nanofibers
(PVA-TN) were synthesized using an electrospinning process,
followed by thermal treatment. The photocatalytic activities of these
nanofibers in the degradation of airborne monocyclic aromatics under
visible-light irradiation were examined. This study focuses on the
application of these photocatalysts to the degradation of the target
compounds at sub-part-per-million indoor air concentrations. The
characteristics of the photocatalysts were examined using scanning
electron microscopy, X-ray diffraction, ultraviolet-visible
spectroscopy, and Fourier-transform infrared spectroscopy. For all the
target compounds, the PVA-TCCNs showed photocatalytic
degradation efficiencies superior to those of the reference PVA-TN.
Specifically, the average photocatalytic degradation efficiencies for
benzene, toluene, ethyl benzene, and o-xylene (BTEX) obtained using
the PVA-TCCNs with a PVA-to-solvent ratio of 0.3 (PVA-TCCN-0.3)
were 11%, 59%, 89%, and 92%, respectively, whereas those observed
using PVA-TNs were 5%, 9%, 28%, and 32%, respectively.
PVA-TCCN-0.3 displayed the highest photocatalytic degradation
efficiency for BTEX, suggesting the presence of an optimal
PVA-to-solvent ratio for the synthesis of PVA-TCCNs. The average
photocatalytic efficiencies for BTEX decreased from 11% to 4%, 59%
to 18%, 89% to 37%, and 92% to 53%, respectively, when the flow
rate was increased from 1.0 to 4.0 L min1. In addition, the average
photocatalytic efficiencies for BTEX increased 11% to ~0%, 59% to
3%, 89% to 7%, and 92% to 13%, respectively, when the input
concentration increased from 0.1 to 1.0 ppm. The prepared
PVA-TCCNs were effective for the purification of airborne aromatics
at indoor concentration levels, particularly when the operating
conditions were optimized.
Abstract: This paper presents powerful techniques for the
development of a new monitoring method based on multi-scale
entropy (MSE) in order to characterize the behaviour of the
concentrations of different gases present in the synthesis of Ammonia
and soft-sensor based on Principal Component Analysis (PCA).
Abstract: Paints are the most widely used methods of protection
against atmospheric corrosion of metals. The aim of this work was to
determine the protective performance of epoxy coating against sea
water before and after damage.
Investigations are conducted using stationary and non-stationary
electrochemical tools such as electrochemical impedance
spectroscopy has allowed us to characterize the protective qualities of
these films. The application of the EIS on our damaged in-situ
painting shows the existence of several capacitive loops which is an
indicator of the failure of our tested paint. Microscopic analysis
(micrograph) helped bring essential elements in understanding the
degradation of our paint condition and immersion training corrosion
products.
Abstract: The characteristics of temperature distribution and
electric field in a natural rubber glove (NRG) using microwave
energy during microwave heating process are investigated
numerically and experimentally. A three-dimensional model of NRG
and microwave oven are considered in this work. The influences of
position, heating time and rotation angle of NRG on temperature
distribution and electric field are presented in details. The coupled
equations of electromagnetic wave propagation and heat transfer are
solved using the finite element method (FEM). The numerical model
is validated with an experimental study at a frequency of 2.45 GHz.
The results show that the numerical results closely match the
experimental results. Furthermore, it is found that the temperature
distribution and electric field increases with increasing heating time.
The hot spot zone appears in NRG at the tip of middle finger while
the maximum temperature occurs in case of rotation angle of NRG =
60 degree. This investigation provides the essential aspects for a
fundamental understanding of heat transport of NRG using
microwave energy in industry.
Abstract: Co metal supported on SiO2 and Al2O3 catalysts with
a metal loading varied from 30 of 70 wt.% were evaluated for
decomposition of methane to COx free hydrogen and carbon
nanomaterials. The catalytic runs were carried out from 550-800oC
under atmospheric pressure using fixed bed vertical flow reactor. The
fresh and spent catalysts were characterized by BET surface area
analyzer, XRD, SEM, TEM and TG analysis. The data showed that
50% Co/Al2O3 catalyst exhibited remarkable higher activity at 800oC
with respect to H2 production compared to rest of the catalysts.
However, the catalytic activity and durability was greatly declined at
higher temperature. The main reason for the catalytic inhibition of Co
containing SiO2 catalysts is the higher reduction temperature of
Co2SiO4. TEM images illustrate that the carbon materials with
various morphologies, carbon nanofibers (CNFs), helical-shaped
CNFs and branched CNFs depending on the catalyst composition and
reaction temperature were obtained.
Abstract: In this study, several crossplots of the P-impedance
with the lithology logs (gamma ray, neutron porosity, deep resistivity,
water saturation and Vp/Vs curves) were made in three available
wells, which were drilled in central part of the Blue Nile basin in
depths varies from 1460m to 1600m. These crossplots were
successful to discriminate between sand and shale when using PImpedance
values, and between the wet sand and the pay sand when
using both P-impedance and Vp/Vs together. Also some impedance
sections were converted to porosity sections using linear formula to
characterize the reservoir in terms of porosity. The used crossplots
were created on log resolution, while the seismic resolution can
identify only the reservoir, unless a 3D seismic angle stacks were
available; then it would be easier to identify the pay sand with great
confidence; through high resolution seismic inversion and
geostatistical approach when using P-impedance and Vp/Vs volumes.