Abstract: An optimized design of E/O and O/E for access points
of WiMAX RoF was carried out by evaluating RCE. The use of the
DFB-LD, a low input-impedance driving, a low distortion PIN-PD,
and a high gain EPHEMT amplifier is promising the cost-effective
design. For the uplink RoF design, the use of EDFA and EP-HEMT
amplifiers is necessity.
Abstract: Various methods of geofield parameters restoration (by algebraic polynoms; filters; rational fractions; interpolation splines; geostatistical methods – kriging; search methods of nearest points – inverse distance, minimum curvature, local – polynomial interpolation; neural networks) have been analyzed and some possible mistakes arising during geofield surface modeling have been presented.
Abstract: This paper presents the results of a preventive maintenance application-based study and modeling of failure rates in breakers of electrical distribution systems. This is a critical issue in the reliability assessment of a system. In the analysis conducted in this paper, the impacts of failure rate variations caused by a preventive maintenance are examined. This is considered as a part of a Reliability Centered Maintenance (RCM) application program. A number of load point reliability indices is derived using the mathematical model of the failure rate, which is established using the observed data in a distribution system.
Abstract: As a part of an evaluation system for R&D programs,
the Korean Government has applied the preliminary feasibility study
to new government R&D program plans. Basically, the fundamental purpose of the preliminary feasibility study is to decide that the
government will either do or do not invest in a new R&D Program. Additionally, the preliminary feasibility study can contribute to the
improvement of R&D program plans. For example, 2 cases of new
R&D program plans applied to the study are explained in this paper and there are expectations that these R&D programs would yield better
performance than without the study. It is thought that the important point of the preliminary feasibility study is not only the effective
decision making process of R&D program but also the opportunity to improve R&D program plan actually.
Abstract: Dried soy protein hydrolysate powder was added to
the burger in order to enhance the oxidative stability as well as
decreases the microbial spoilage. The soybean bioactive compounds
(soy protein hydrolysate) as antioxidant and antimicrobial were added
at level of 1, 2 and 3 %.Chemical analysis and physical properties
were affected by protein hydrolysate addition. The TBA values were
significantly affected (P < 0.05) by the storage period and the level of
soy protein hydrolysate. All the tested soybean protein hydrolysate
additives showed strong antioxidant properties. Samples of soybean
protein hydrolysate showed the lowest (P < 0.05) TBA values at each
time of storage.
The counts of all determined microbiological indicators were
significantly (P < 0.05) affected by the addition of the soybean
protein hydrolysate. Decreasing trends of different extent were also
observed in samples of the treatments for total viable counts,
Coliform, Staphylococcus aureus, yeast and molds. Storage period
was being significantly (P < 0.05) affected on microbial counts in all
samples Staphylococcus aureus were the most sensitive microbe
followed by Coliform group of the sample containing protein
hydrolysate, while molds and yeast count showed a decreasing trend
but not significant (P < 0.05) until the end of the storage period
compared with control sample. Sensory attributes were also
performed, added protein hydrolysate exhibits beany flavor which
was clear about samples of 3% protein hydrolysate.
Abstract: The main aim of this study was to examine whether
people understand indicative conditionals on the basis of syntactic
factors or on the basis of subjective conditional probability. The
second aim was to investigate whether the conditional probability of
q given p depends on the antecedent and consequent sizes or derives
from inductive processes leading to establish a link of plausible cooccurrence
between events semantically or experientially associated.
These competing hypotheses have been tested through a 3 x 2 x 2 x 2
mixed design involving the manipulation of four variables: type of
instructions (“Consider the following statement to be true", “Read the
following statement" and condition with no conditional statement);
antecedent size (high/low); consequent size (high/low); statement
probability (high/low). The first variable was between-subjects, the
others were within-subjects. The inferences investigated were Modus
Ponens and Modus Tollens. Ninety undergraduates of the Second
University of Naples, without any prior knowledge of logic or
conditional reasoning, participated in this study.
Results suggest that people understand conditionals in a syntactic
way rather than in a probabilistic way, even though the perception of
the conditional probability of q given p is at least partially involved in
the conditionals- comprehension. They also showed that, in presence
of a conditional syllogism, inferences are not affected by the
antecedent or consequent sizes. From a theoretical point of view these
findings suggest that it would be inappropriate to abandon the idea
that conditionals are naturally understood in a syntactic way for the
idea that they are understood in a probabilistic way.
Abstract: In this paper, the torsion capacity of ultimate point on rectangular beams with spiral reinforcements in the torsion direction and its anti-direction are investigated. Therefore, models of above-mentioned beams have been numerically analyzed under various loads using ANSYS software. It was observed that, spirallyreinforced prismatic beam and beam with spiral links, show lower torsion capacity than beam with normal links also in anti-direction. The result is that the concrete regulations are violated in this case.
Abstract: This study applied the Gaussian trajectory
transfer-coefficient model (GTx) to simulate the particulate matter
concentrations and the source apportionments at Nanzih Air Quality
Monitoring Station in southern Taiwan from November 2007 to
February 2008. The correlation coefficient between the observed and
the calculated daily PM10 concentrations is 0.5 and the absolute bias of
the PM10 concentrations is 24%. The simulated PM10 concentrations
matched well with the observed data. Although the emission rate of
PM10 was dominated by area sources (58%), the results of source
apportionments indicated that the primary sources for PM10 at Nanzih
Station were point sources (42%), area sources (20%) and then upwind
boundary concentration (14%). The obvious difference of PM10 source
apportionment between episode and non-episode days was upwind
boundary concentrations which contributed to 20% and 11% PM10
sources, respectively. The gas-particle conversion of secondary
aerosol and long range transport played crucial roles on the PM10
contribution to a receptor.
Abstract: The purpose of this study is to suggest energy efficient
routing for ad hoc networks which are composed of nodes with limited
energy. There are diverse problems including limitation of energy
supply of node, and the node energy management problem has been
presented. And a number of protocols have been proposed for energy
conservation and energy efficiency. In this study, the critical point of
the EA-MPDSR, that is the type of energy efficient routing using only
two paths, is improved and developed. The proposed TP-MESR uses
multi-path routing technique and traffic prediction function to increase
number of path more than 2. It also verifies its efficiency compared to
EA-MPDSR using network simulator (NS-2). Also, To give a
academic value and explain protocol systematically, research
guidelines which the Hevner(2004) suggests are applied. This
proposed TP-MESR solved the existing multi-path routing problem
related to overhead, radio interference, packet reassembly and it
confirmed its contribution to effective use of energy in ad hoc
networks.
Abstract: Composite steel-concrete slabs using thin-walled
corrugated steel sheets with embossments represent a modern and
effective combination of steel and concrete. However, the design
of new types of sheeting is conditional on the execution of expensive
and time-consuming laboratory testing. The effort to develop
a cheaper and faster method has lead to many investigations all over
the world. In our paper we compare the results from our experiments
involving vacuum loading, four-point bending and small-scale shear
tests.
Abstract: This paper numerically investigates the effects of input
speed on the overall dynamic characteristics of a multi-body system
with differently located revolute clearance joints without friction. A
typical planar slider-crank mechanism is used as a demonstration case
in which the effects of the input speed on the dynamic performance
of the mechanism with a revolute clearance joint between the crank
and connecting rod, and between the connecting rod and slider are
separately investigated with comprehensive observations numerically
presented. It is observed that, changing the driving speed of a multibody
system makes the behavior of the system to change from
either periodic to chaotic, or chaotic to periodic depending on which
joint has clearance. The location of the clearance revolute joint and
the operating speed of a multi-body system play a crucial role in
predicting accurately the dynamic responses of the system. Therefore
the dynamic behavior of one clearance revolute joint cannot be used
as a general case for a mechanical system.
Abstract: A comparative evaluation of acute toxicity of
synthesized nano silvers using two different procedures (biological
and chemical reduction methods) and silver ions on bacteria
Vibrio fischeri was investigated. The bacterial light inhibition test as
a toxicological endpoint was used by applying of a homemade
luminometer. To compare the toxicity effects as a quantitative
parameter, a nominal effective concentrations (EC) of chemicals and
a susceptibility constant (Z-value) of bacteria, after 5 min and 30 min
exposure times, were calculated. After 5 and 30 min contact times,
the EC50 values of two silver nanoparticles and the EC20 values were
about similar. It demonstrates that toxicity of silvers was independent
of their procedure. The EC values of nanoparticles were larger than
those of the silver ions. The susceptibilities(Z- Values) of V.fischeri
(L/mg) to the silver ions were greater than those of the nano silvers.
According to the EC and Z values, the toxicity of silvers decreased in
the following order: Silver ions >> silver nanoparticles from
chemical reduction method ~ silver nanoparticles from biological
method.
Abstract: In this paper we present the algorithm which allows
us to have an object tracking close to real time in Full HD videos.
The frame rate (FR) of a video stream is considered to be between
5 and 30 frames per second. The real time track building will be
achieved if the algorithm can follow 5 or more frames per second. The
principle idea is to use fast algorithms when doing preprocessing to
obtain the key points and track them after. The procedure of matching
points during assignment is hardly dependent on the number of points.
Because of this we have to limit pointed number of points using the
most informative of them.
Abstract: The American Health Level Seven (HL7) Reference Information Model (RIM) consists of six back-bone classes that have different specialized attributes. Furthermore, for the purpose of enforcing the semantic expression, there are some specific mandatory vocabulary domains have been defined for representing the content values of some attributes. In the light of the fact that it is a duplicated effort on spending a lot of time and human cost to develop and modify Clinical Information Systems (CIS) for most hospitals due to the variety of workflows. This study attempts to design and develop sharing RIM-based components of the CIS for the different business processes. Therefore, the CIS contains data of a consistent format and type. The programmers can do transactions with the RIM-based clinical repository by the sharing RIM-based components. And when developing functions of the CIS, the sharing components also can be adopted in the system. These components not only satisfy physicians- needs in using a CIS but also reduce the time of developing new components of a system. All in all, this study provides a new viewpoint that integrating the data and functions with the business processes, it is an easy and flexible approach to build a new CIS.
Abstract: In this paper, multi-processors job shop scheduling problems are solved by a heuristic algorithm based on the hybrid of priority dispatching rules according to an ant colony optimization algorithm. The objective function is to minimize the makespan, i.e. total completion time, in which a simultanous presence of various kinds of ferons is allowed. By using the suitable hybrid of priority dispatching rules, the process of finding the best solution will be improved. Ant colony optimization algorithm, not only promote the ability of this proposed algorithm, but also decreases the total working time because of decreasing in setup times and modifying the working production line. Thus, the similar work has the same production lines. Other advantage of this algorithm is that the similar machines (not the same) can be considered. So, these machines are able to process a job with different processing and setup times. According to this capability and from this algorithm evaluation point of view, a number of test problems are solved and the associated results are analyzed. The results show a significant decrease in throughput time. It also shows that, this algorithm is able to recognize the bottleneck machine and to schedule jobs in an efficient way.
Abstract: Economic Load Dispatch (ELD) is a method of determining
the most efficient, low-cost and reliable operation of a power
system by dispatching available electricity generation resources to
supply load on the system. The primary objective of economic
dispatch is to minimize total cost of generation while honoring
operational constraints of available generation resources. In this paper
an intelligent water drop (IWD) algorithm has been proposed to
solve ELD problem with an objective of minimizing the total cost of
generation. Intelligent water drop algorithm is a swarm-based natureinspired
optimization algorithm, which has been inspired from natural
rivers. A natural river often finds good paths among lots of possible
paths in its ways from source to destination and finally find almost
optimal path to their destination. These ideas are embedded into
the proposed algorithm for solving economic load dispatch problem.
The main advantage of the proposed technique is easy is implement
and capable of finding feasible near global optimal solution with
less computational effort. In order to illustrate the effectiveness of
the proposed method, it has been tested on 6-unit and 20-unit test
systems with incremental fuel cost functions taking into account the
valve point-point loading effects. Numerical results shows that the
proposed method has good convergence property and better in quality
of solution than other algorithms reported in recent literature.
Abstract: The only relevant basis for the design of an educational application are objectives of learning for the content area. This study analyses the process in which the real – not only the formal – objectives could work as the starting point for the construction of an educational game. The application context is the education of perioperative nursing. The process is based on the panel discussions of nursing teachers. In the panels, the teachers elaborated the objectives. The transcribed discussions were analysed in terms of the conceptions of learning and teaching of perioperative nursing. The outcome of the study is first the elaborated objectives, which will be used in the implementation of an educational game for the needs of pre-, intra and post-operative nursing skills learning. Second, the study shows that different views of learning are necessary to be understood in order to design an appropriate educational application.
Abstract: Key management is a vital component in any modern security protocol. Due to scalability and practical implementation considerations automatic key management seems a natural choice in significantly large virtual private networks (VPNs). In this context IETF Internet Key Exchange (IKE) is the most promising protocol under permanent review. We have made a humble effort to pinpoint IKEv2 net gain over IKEv1 due to recent modifications in its original structure, along with a brief overview of salient improvements between the two versions. We have used US National Institute of Technology NIIST VPN simulator to get some comparisons of important performance metrics.
Abstract: The evolution of silica optical fiber strength aged in cetyltrimethylammonium chloride solution (CTAC) has been investigated. If the solution containing surfactants presents appreciable changes in physical and chemical properties at the critical micelle concentration (CMC), a non negligible mechanical behavior fiber change is observed for silica fiber aged in cationic surfactants as CTAC which can lead to optical fiber reliability questioning. The purpose of this work is to study the mechanical behavior of silica coated and naked optical fibers in contact with CTAC solution at different concentrations. Result analysis proves that the immersion in CTAC drastically decreases the fiber strength and specially near the CMC point. Beyond CMC point, a small increase of fiber strength is analyzed and commented.
Abstract: Palm oil could be converted to cocoa butter equivalent by lipase-catalyzed interesterification. The objective of this research was to investigate the structure modification of palm oil to cocoa butter equivalent using Carica papaya lipase –catalyzed interesterification. The study showed that the compositions of cocoa butter equivalent were affected by acyl donor sources, substrate ratio, initial water of enzyme, reaction time, reaction temperature and the amount of enzyme. Among three acyl donors tested (methyl stearate, ethyl stearate and stearic acid), methyl stearate appeared to be the best acyl donor for incorporation to palm oil structure. The best reaction conditions for cocoa butter equivalent production were : substrate ratio (palm oil : methyl stearate, mol/mol) at 1 : 4, water activity of enzyme at 0.11, reaction time at 4 h, reaction temperature at 45 ° C and 18% by weight of the enzyme. The chemical and physical properties of cocoa butter equivalent were 9.75 ± 0.41% free fatty acid, 44.89 ± 0.84 iodine number, 193.19 ± 0.78 sponification value and melting point at 37-39 °C.