Abstract: Fractional-order controller was proven to perform better than the integer-order controller. However, the absence of a pole at origin produced marginal error in fractional-order control system. This study demonstrated the enhancement of the fractionalorder PI over the integer-order PI in a steam temperature control. The fractional-order controller was cascaded with an error compensator comprised of a very small zero and a pole at origin to produce a zero steady-state error for the closed-loop system. Some modification on the error compensator was suggested for different order fractional integrator that can improve the overall phase margin.
Abstract: South Africa is facing a crisis with not being able to produce enough graduates in the scarce skills areas to sustain economic growth. The crisis is fuelled by a school system that does not produce enough potential students with Mathematics, Accounting and Science. Since the introduction of the new school curriculum in 2008, there is no longer an option to take pure maths on a standard grade level. Instead, only two mathematical subjects are offered: pure maths (which is on par with higher grade maths) and mathematical literacy. It is compulsory to take one or the other. As a result, lees student finishes Grade 12 with pure mathematics every year. This national problem needs urgent attention if South Africa is to make any headway in critical skills development as mathematics is a gateway to scarce skills professions. Higher education institutions initiated several initiatives in an attempt to address the above, including preparatory courses, bridging programmes and extended curricula with foundation provisions. In view of the above, and government policy directives to broaden access in the scarce skills areas to increase student throughput, foundation provision was introduced for Commerce and Information Technology programmes at the Vaal Triangle Campus (VTC) of North-West University (NWU) in 2010. Students enrolling for extended programmes do not comply with the minimum prerequisites for the normal programmes. The question then arises as to whether these programmes have the intended impact? This paper reports the results of a two year longitudinal study, tracking the first year academic achievement of the two cohorts of enrolments since 2010. The results provide valuable insight into the structuring of an extended programme and its potential impact.
Abstract: This article is based on the technique which is called
Discrete Parameter Tracking (DPT). First introduced by A. A. Azab
[8] which is applicable for less order reference model. The order of
the reference model is (n-l) and n is the number of the adjustable
parameters in the physical plant.
The technique utilizes a modified gradient method [9] where the
knowledge of the exact order of the nonadaptive system is not
required, so, as to eliminate the identification problem. The
applicability of the mentioned technique (DPT) was examined
through the solution of several problems.
This article introduces the solution of a third order system with
three adjustable parameters, controlled according to second order
reference model. The adjustable parameters have great initial error
which represent condition.
Computer simulations for the solution and analysis are provided
to demonstrate the simplicity and feasibility of the technique.
Abstract: The purpose of this paper is to investigate the
durability of cement mortar in presence of Rice Husk Ash (RHA).
The strength and durability of mortar with different replacement
level (0%, 10%, 15%, 20%, 25% and 30%) of Ordinary Portland
Cement (OPC) by RHA is investigated here. RHA was
manufactured from an uncontrolled burning process. Test samples
were prepared with river sand of FM 2.73. Samples were kept in
controlled environment up to test time. The results show that
addition of RHA was shown better results for 20% replacement
level than OPC at 90 days. In durability test all samples passed for
20 cycles except 25% and 30% replacement level.
Abstract: This paper describes the two stage control using a disturbance observer and a Kalman filter. The system feedback uses the estimated state when it controls the speed. After the change-over point, its feedback uses the controlled plant output when it controls the position. To change the system continually, a change-over point has to be determined pertinently, and the controlled plant input has to be adjusted by the addition of the appropriate value. The proposed method has noise-reduction effect. It changes the system continually, even if the controlled plant identification has the error. Although the conventional method needs a speed sensor, the proposed method does not need it. The proposed method has a superior robustness compared with the conventional two stage control.
Abstract: At any point of time, a power system operating
condition should be stable, meeting various operational criteria and it
should also be secure in the event of any credible contingency. Present
day power systems are being operated closer to their stability limits
due to economic and environmental constraints. Maintaining a stable
and secure operation of a power system is therefore a very important
and challenging issue. Voltage instability has been given much
attention by power system researchers and planners in recent years,
and is being regarded as one of the major sources of power system
insecurity. Voltage instability phenomena are the ones in which the
receiving end voltage decreases well below its normal value and does
not come back even after setting restoring mechanisms such as VAR
compensators, or continues to oscillate for lack of damping against the
disturbances. Reactive power limit of power system is one of the major
causes of voltage instability. This paper investigates the effects of
coordinated series capacitors (SC) with static VAR compensators
(SVC) on steady-state voltage stability of a power system. Also, the
influence of the presence of series capacitor on static VAR
compensator controller parameters and ratings required to stabilize
load voltages at certain values are highlighted.
Abstract: Space Vector Pulse Width Modulation SVPWM is
one of the most used techniques to generate sinusoidal voltage and
current due to its facility and efficiency with low harmonics
distortion. This algorithm is specially used in power electronic
applications. This paper describes simulation algorithm of SVPWM
& SPWM using MatLab/simulink environment. It also implements a
closed loop three phases DC-AC converter controlling its outputs
voltages amplitude and frequency using MatLab. Also comparison
between SVPWM & SPWM results is given.
Abstract: With constraints on data availability and for study of power system stability it is adequate to model the synchronous generator with field circuit and one equivalent damper on q-axis known as the model 1.1. This paper presents a systematic procedure for modelling and simulation of a single-machine infinite-bus power system installed with a thyristor controlled series compensator (TCSC) where the synchronous generator is represented by model 1.1, so that impact of TCSC on power system stability can be more reasonably evaluated. The model of the example power system is developed using MATLAB/SIMULINK which can be can be used for teaching the power system stability phenomena, and also for research works especially to develop generator controllers using advanced technologies. Further, the parameters of the TCSC controller are optimized using genetic algorithm. The non-linear simulation results are presented to validate the effectiveness of the proposed approach.
Abstract: Aspect Oriented Programming promises many
advantages at programming level by incorporating the cross cutting
concerns into separate units, called aspects. Join Points are
distinguishing features of Aspect Oriented Programming as they
define the points where core requirements and crosscutting concerns
are (inter)connected. Currently, there is a problem of multiple
aspects- composition at the same join point, which introduces the
issues like ordering and controlling of these superimposed aspects.
Dynamic strategies are required to handle these issues as early as
possible. State chart is an effective modeling tool to capture dynamic
behavior at high level design. This paper provides methodology to
formulate the strategies for multiple aspect composition at high level,
which helps to better implement these strategies at coding level. It
also highlights the need of designing shared join point at high level,
by providing the solutions of these issues using state chart diagrams
in UML 2.0. High level design representation of shared join points
also helps to implement the designed strategy in systematic way.
Abstract: The author present PID controller design for
following control of hard disk drive by characteristic ratio assignment
method. The study in this paper concerns design of a PID controller
which sufficiently robust to the disturbances and plant perturbations
on following control of hard disk drive. Characteristic Ratio
Assignment (CRA) is shown to be an efficient control technique to
serve this requirement. The controller design by CRA is based on the
choice of the coefficients of the characteristic polynomial of the
closed loop system according to the convenient performance criteria
such as equivalent time constant and ration of characteristic
coefficient. Hence, in this study, CRA method is applied in PID
controller design for following control of hard disk drive. Matlab
simulation results shown that CRA design is fairly stable and robust
whilst giving the convenience in controller-s parameters adjustment.
Abstract: Fully customized hardware based technology provides high performance and low power consumption by specializing the tasks in hardware but lacks design flexibility since any kind of changes require re-design and re-fabrication. Software based solutions operate with software instructions due to which a great flexibility is achieved from the easy development and maintenance of the software code. But this execution of instructions introduces a high overhead in performance and area consumption. In past few decades the reconfigurable computing domain has been introduced which overcomes the traditional trades-off between flexibility and performance and is able to achieve high performance while maintaining a good flexibility. The dramatic gains in terms of chip performance and design flexibility achieved through the reconfigurable computing systems are greatly dependent on the design of their computational units being integrated with reconfigurable logic resources. The computational unit of any reconfigurable system plays vital role in defining its strength. In this research paper an RFU based computational unit design has been presented using the tightly coupled, multi-threaded reconfigurable cores. The proposed design has been simulated for VLIW based architectures and a high gain in performance has been observed as compared to the conventional computing systems.
Abstract: In this paper, a generalized synchronization scheme, which is called function synchronization, for chaotic systems is studied. Based on Lyapunov method and active control method, we design the synchronization controller for the system such that the error dynamics between master and slave chaotic systems is asymptotically stable. For verification of our theory, computer and circuit simulations for a specific chaotic system is conducted.
Abstract: This paper presents a design and prototype
implementation of new home automation system that uses WiFi
technology as a network infrastructure connecting its parts. The
proposed system consists of two main components; the first part is
the server (web server), which presents system core that manages,
controls, and monitors users- home. Users and system administrator
can locally (LAN) or remotely (internet) manage and control system
code. Second part is hardware interface module, which provides
appropriate interface to sensors and actuator of home automation
system. Unlike most of available home automation system in the
market the proposed system is scalable that one server can manage
many hardware interface modules as long as it exists on WiFi
network coverage. System supports a wide range of home
automation devices like power management components, and
security components. The proposed system is better from the
scalability and flexibility point of view than the commercially
available home automation systems.
Abstract: This study analyzed environmental health risks and
people-s perceptions of risks related to waste management in poor
settlements of Abidjan, to develop integrated solutions for health and
well-being improvement. The trans-disciplinary approach used relied
on remote sensing, a geographic information system (GIS),
qualitative and quantitative methods such as interviews and a
household survey (n=1800). Mitigating strategies were then
developed using an integrated participatory stakeholder workshop.
Waste management deficiencies resulting in lack of drainage and
uncontrolled solid and liquid waste disposal in the poor settlements
lead to severe environmental health risks. Health problems were
caused by direct handling of waste, as well as through broader
exposure of the population. People in poor settlements had little
awareness of health risks related to waste management in their
community and a general lack of knowledge pertaining to sanitation
systems. This unfortunate combination was the key determinant
affecting the health and vulnerability. For example, an increased
prevalence of malaria (47.1%) and diarrhoea (19.2%) was observed
in the rainy season when compared to the dry season (32.3% and
14.3%). Concerted and adapted solutions that suited all the
stakeholders concerned were developed in a participatory workshop
to allow for improvement of health and well-being.
Abstract: Condition monitoring of electrical power equipment
has attracted considerable attention for many years. The aim of this
paper is to use Labview with Fuzzy Logic controller to build a
simulation system to diagnose transformer faults and monitor its
condition. The front panel of the system was designed using
LabVIEW to enable computer to act as customer-designed
instrument. The dissolved gas-in-oil analysis (DGA) method was
used as technique for oil type transformer diagnosis; meanwhile
terminal voltages and currents analysis method was used for dry type
transformer. Fuzzy Logic was used as expert system that assesses all
information keyed in at the front panel to diagnose and predict the
condition of the transformer. The outcome of the Fuzzy Logic
interpretation will be displayed at front panel of LabVIEW to show
the user the conditions of the transformer at any time.
Abstract: In this paper multivariable predictive PID controller has
been implemented on a multi-inputs multi-outputs control problem
i.e., quadruple tank system, in comparison with a simple multiloop
PI controller. One of the salient feature of this system is an
adjustable transmission zero which can be adjust to operate in both
minimum and non-minimum phase configuration, through the flow
distribution to upper and lower tanks in quadruple tank system.
Stability and performance analysis has also been carried out for this
highly interactive two input two output system, both in minimum
and non-minimum phases. Simulations of control system revealed
that better performance are obtained in predictive PID design.
Abstract: Applicability of tuning the controller gains for Stewart manipulator using genetic algorithm as an efficient search technique is investigated. Kinematics and dynamics models were introduced in detail for simulation purpose. A PD task space control scheme was used. For demonstrating technique feasibility, a Stewart manipulator numerical-model was built. A genetic algorithm was then employed to search for optimal controller gains. The controller was tested onsite a generic circular mission. The simulation results show that the technique is highly convergent with superior performance operating for different payloads.
Abstract: This paper employs a new approach to regulate the
blood glucose level of type I diabetic patient under an intensive
insulin treatment. The closed-loop control scheme incorporates
expert knowledge about treatment by using reinforcement learning
theory to maintain the normoglycemic average of 80 mg/dl and the
normal condition for free plasma insulin concentration in severe
initial state. The insulin delivery rate is obtained off-line by using Qlearning
algorithm, without requiring an explicit model of the
environment dynamics. The implementation of the insulin delivery
rate, therefore, requires simple function evaluation and minimal
online computations. Controller performance is assessed in terms of
its ability to reject the effect of meal disturbance and to overcome the
variability in the glucose-insulin dynamics from patient to patient.
Computer simulations are used to evaluate the effectiveness of the
proposed technique and to show its superiority in controlling
hyperglycemia over other existing algorithms
Abstract: This paper presents the impact study of GTO Controlled Series Capacitor (GCSC) parameters on measured impedance (Zseen) by MHO distance relays for single transmission line high voltage 220 kV in the presence of single phase to earth fault with fault resistance (RF). The study deals with a 220 kV single electrical transmission line of Eastern Algerian transmission networks at Group Sonelgaz (Algerian Company of Electrical and Gas) compensated by series Flexible AC Transmission System (FACTS) i.e. GCSC connected at midpoint of the transmission line. The transmitted active and reactive powers are controlled by three GCSC-s. The effects of maximum reactive power injected as well as injected maximum voltage by GCSC on distance relays measured impedance is treated. The simulations results investigate the effects of GCSC injected parameters: variable reactance (XGCSC), variable voltage (VGCSC) and reactive power injected (QGCSC) on measured resistance and reactance in the presence of earth fault with resistance fault varied between 5 to 50 Ω for three cases study.
Abstract: This paper presents modeling and simulation of Grid Connected Photovoltaic (PV) system by using improved mathematical model. The model is used to study different parameter variations and effects on the PV array including operating temperature and solar irradiation level. In this paper stepped P&O algorithm is proposed for MPPT control. This algorithm will identify the suitable duty ratio in which the DC-DC converter should be operated to maximize the power output. Photo voltaic array with proposed stepped P&O-MPPT controller can operate in the maximum power point for the whole range of solar data (irradiance and temperature).