Abstract: Image enhancement is a challenging issue in many applications. In the last two decades, there are various filters developed. This paper proposes a novel method which removes Gaussian noise from the gray scale images. The proposed technique is compared with Enhanced Fuzzy Peer Group Filter (EFPGF) for various noise levels. Experimental results proved that the proposed filter achieves better Peak-Signal-to-Noise-Ratio PSNR than the existing techniques. The proposed technique achieves 1.736dB gain in PSNR than the EFPGF technique.
Abstract: The use of energy dissipation systems for seismic applications has increased worldwide, thus it is necessary to develop practical and modern criteria for their optimal design. Here, a direct displacement-based seismic design approach for frame buildings with hysteretic energy dissipation systems (HEDS) is applied. The building is constituted by two individual structural systems consisting of: 1) a main elastic structural frame designed for service loads; and 2) a secondary system, corresponding to the HEDS, that controls the effects of lateral loads. The procedure implies to control two design parameters: a) the stiffness ratio (α=Kframe/Ktotal system), and b) the strength ratio (γ=Vdamper/Vtotal system). The proposed damage-controlled approach contributes to the design of a more sustainable and resilient building because the structural damage is concentrated on the HEDS. The reduction of the design displacement spectrum is done by means of a damping factor (recently published) for elastic structural systems with HEDS, located in Mexico City. Two limit states are verified: serviceability and near collapse. Instead of the traditional trial-error approach, a procedure that allows the designer to establish the preliminary sizes of the structural elements of both systems is proposed. The design methodology is applied to an 8-story steel building with buckling restrained braces, located in soft soil of Mexico City. With the aim of choosing the optimal design parameters, a parametric study is developed considering different values of હ and . The simplified methodology is for preliminary sizing, design, and evaluation of the effectiveness of HEDS, and it constitutes a modern and practical tool that enables the structural designer to select the best design parameters.
Abstract: A reliability-based methodology which uses structural demand hazard curves to consider the increment of the ductility demands of structures with tilting is proposed. The approach considers the effect of two orthogonal components of the ground motions as well as the influence of soil-structure interaction. The approach involves the calculation of ductility demand hazard curves for symmetric systems and, alternatively, for systems with different degrees of asymmetry. To get this objective, demand hazard curves corresponding to different global ductility demands of the systems are calculated. Next, Uniform Exceedance Rate Spectra (UERS) are developed for a specific mean annual rate of exceedance value. Ratios between UERS corresponding to asymmetric and to symmetric systems located in soft soil of the valley of Mexico are obtained. Results indicate that the ductility demands corresponding to tilted structures may be several times higher than those corresponding to symmetric structures, depending on several factors such as tilting angle and vibration period of structure and soil.
Abstract: The present work attempts to investigate the
combustion, performance and emission characteristics of an existing
single-cylinder four-stroke compression-ignition engine operated in
dual-fuel mode with hydrogen as an alternative fuel. Environmental
concerns and limited amount of petroleum fuels have caused interests
in the development of alternative fuels like hydrogen for internal
combustion (IC) engines. In this experimental investigation, a diesel
engine is made to run using hydrogen in dual fuel mode with diesel,
where hydrogen is introduced into the intake manifold using an LPGCNG
injector and pilot diesel is injected using diesel injectors. A
Timed Manifold Injection (TMI) system has been developed to vary
the injection strategies. The optimized timing for the injection of
hydrogen was 10^0 CA after top dead center (ATDC). From the study
it was observed that with increasing hydrogen rate, enhancement in
brake thermal efficiency (BTHE) of the engine has been observed
with reduction in brake specific energy consumption (BSEC).
Furthermore, Soot contents decrease with an increase in indicated
specific NOx emissions with the enhancement of hydrogen flow rate.
Abstract: The paper presents a new method for efficient
innovation process management. Even though the innovation
management methods, tools and knowledge are well established and
documented in literature, most of the companies still do not manage it
efficiently. Especially in SMEs the front end of innovation - problem
identification, idea creation and selection - is often not optimally
performed. Our eMIPS methodology represents a sort of "umbrella
methodology" - a well-defined set of procedures, which can be
dynamically adapted to the concrete case in a company. In daily
practice, various methods (e.g. for problem identification and idea
creation) can be applied, depending on the company's needs. It is
based on the proactive involvement of the company's employees
supported by the appropriate methodology and external experts. The
presented phases are performed via a mixture of face-to-face
activities (workshops) and online (eLearning) activities taking place
in eLearning Moodle environment and using other e-communication
channels. One part of the outcomes is an identified set of
opportunities and concrete solutions ready for implementation. The
other also very important result is connected to innovation
competences for the participating employees related with concrete
tools and methods for idea management. In addition, the employees
get a strong experience for dynamic, efficient and solution oriented
managing of the invention process. The eMIPS also represents a way
of establishing or improving the innovation culture in the
organization. The first results in a pilot company showed excellent
results regarding the motivation of participants and also as to the
results achieved.
Abstract: This paper presents a study the effect of nose radius
(Rz-mm) on cutting force components and temperatures during the
machining simulation in an orthogonal cutting process for titanium
alloy (Ti-6Al-4V). The cutting process was performed at various
nose radiuses (Rz-mm) while the depth of cut (d-mm), feed rate (fmm/
tooth) and cutting speed (vc-m/ min) were remained constant.
The main cutting force (Fc), feed cutting force (Ft) and temperatures
were estimated by using finite element modeling (FEM) through
ABAQUS/EXPLICIT software and the simulation was developed the
two-dimension via an orthogonal cutting process during machining
titanium alloy (Ti-6Al-4V). The results led to the conclusion that the
nose radius (Rz-mm) has affected directly on the cutting force
components. However, temperature gave no indication or has no
significant relation with nose radius during machining titanium alloy
(Ti-6Al-4V). Hence, any increase or decrease in the nose radius (Rzmm)
during machining operation led to effect on the cutting forces
and thus it will be effective on surface finish, quality, and quantity of
products.
Abstract: Moving into a new era of healthcare, new tools and
devices are developed to extend and improve health services, such as
remote patient monitoring and risk prevention. In this concept,
Internet of Things (IoT) and Cloud Computing present great
advantages by providing remote and efficient services, as well as
cooperation between patients, clinicians, researchers and other health
professionals. This paper focuses on patients suffering from bipolar
disorder, a brain disorder that belongs to a group of conditions
called affective disorders, which is characterized by great mood
swings. We exploit the advantages of Semantic Web and Cloud
Technologies to develop a patient monitoring system to support
clinicians. Based on intelligently filtering of evidence-knowledge and
individual-specific information we aim to provide treatment
notifications and recommended function tests at appropriate times or
concluding into alerts for serious mood changes and patient’s nonresponse
to treatment. We propose an architecture as the back-end
part of a cloud platform for IoT, intertwining intelligence devices
with patients’ daily routine and clinicians’ support.
Abstract: Typically, virtual communities exhibit the well-known
phenomenon of participation inequality, which means that only a
small percentage of users is responsible of the majority of
contributions. However, the sustainability of the community requires
that the group of active users must be continuously nurtured with new
users that gain expertise through a participation process. This paper
analyzes the time evolution of Open Source Software (OSS)
communities, considering users that join/abandon the community
over time and several topological properties of the network when
modeled as a social network. More specifically, the paper analyzes
the role of those users rejoining the community and their influence in
the global characteristics of the network.
Abstract: Optical radiation emitted from a metal-coated fiber tip apex at liquid-air interface was measured. The intensity of the output radiation was strongly depend on the relative position of the tip to a liquid-air interface and varied with surface fluctuations. This phenomenon permits in-situ real-time investigation of nano-metric vibrations of the liquid surface and provides a basis for development of various origin ultrasensitive vibration detecting sensors. The described method can be used for detection of week seismic vibrations.
Abstract: Taiwan is a hyper endemic area for the Hepatitis B
virus (HBV). The estimated total number of HBsAg carriers in the
general population who are more than 20 years old is more than 3
million. Therefore, a case record review is conducted from January
2003 to June 2007 for all patients with a diagnosis of acute hepatitis
who were admitted to the Emergency Department (ED) of a
well-known teaching hospital. The cost for the use of medical
resources is defined as the total medical fee. In this study, principal
component analysis (PCA) is firstly employed to reduce the number of
dimensions. Support vector regression (SVR) and artificial neural
network (ANN) are then used to develop the forecasting model. A total
of 117 patients meet the inclusion criteria. 61% patients involved in
this study are hepatitis B related. The computational result shows that
the proposed PCA-SVR model has superior performance than other
compared algorithms. In conclusion, the Child-Pugh score and
echogram can both be used to predict the cost of medical resources for
patients with acute hepatitis in the ED.
Abstract: This paper presents a novel integrated hybrid
approach for fault diagnosis (FD) of nonlinear systems. Unlike most
FD techniques, the proposed solution simultaneously accomplishes
fault detection, isolation, and identification (FDII) within a unified
diagnostic module. At the core of this solution is a bank of adaptive
neural parameter estimators (NPE) associated with a set of singleparameter
fault models. The NPEs continuously estimate unknown
fault parameters (FP) that are indicators of faults in the system. Two
NPE structures including series-parallel and parallel are developed
with their exclusive set of desirable attributes. The parallel scheme is
extremely robust to measurement noise and possesses a simpler, yet
more solid, fault isolation logic. On the contrary, the series-parallel
scheme displays short FD delays and is robust to closed-loop system
transients due to changes in control commands. Finally, a fault
tolerant observer (FTO) is designed to extend the capability of the
NPEs to systems with partial-state measurement.
Abstract: In this paper, the effects of fiber types and elevated
temperatures on compressive strength, modulus of rapture and the
bond characteristics of fiber reinforced concretes (FRC) are
presented. By using the three different types of fibers (steel fiber-SF,
polypropylene-PPF and polyvinyl alcohol-PVA), FRC specimens
were produced and exposed to elevated temperatures up to 800 ºC for
1.5 hours. In addition, a plain concrete (without fiber) was produced
and used as a control. Test results obtained showed that the steel fiber
reinforced concrete (SFRC) had the highest compressive strength,
modulus of rapture and bond stress values at room temperatures, the
residual bond, flexural and compressive strengths of both FRC and
plain concrete dropped sharply after exposure to high temperatures.
The results also indicated that the reduction of bond, flexural and
compressive strengths with increasing the exposed temperature was
relatively less for SFRC than for plain, and FRC with PPF and PVA.
Abstract: The textile industry plays a major role in the economy
of India and on the other side of the coin it is the major source for
water pollution. As azo dyes is the largest dye class they are
extensively used in many fields such as textile industry, leather
tanning industry, paper production, food, color photography,
pharmaceuticals and medicine, cosmetic, hair colorings, wood
staining, agricultural, biological and chemical research etc. In
addition to these, they can have acute and/or chronic effects on
organisms depending on their concentration and length of exposure
when they discharged as effluent in the environment. The aim of this
study was to assess the genotoxic and histotoxic potentials of
environmentally relevant concentrations of C. I. Reactive Red 120
(RR 120) on Catla catla, important edible freshwater fingerlings. For
this, healthy Catla catla fingerlings were procured from the
Government Fish Farm and acclimatized in 100 L capacity and
continuously aerated glass aquarium in laboratory for 15 days.
According to APHA some physic-chemical parameters were
measured and maintained such as temperature, pH, dissolve oxygen,
alkalinity, total hardness. Water along with excreta had been changed
every 24 hrs. All fingerlings were fed artificial food palates once a
day @ body weight. After 15 days fingerlings were grouped in 5 (10
in each) and exposed to various concentrations of RR 120 (Control,
10, 20, 30 and 40 mg.l-1) and samples (peripheral blood and gills,
kidney) were collected and analyzed at 96 hrs. All results were
compared with the control. Micronuclei (MN), nuclear buds (NB),
fragmented-apoptotic (FA) and bi-nucleated (BN) cells in blood
smears and in tissues (gills and kidney cells) were observed.
Prominent histopathological alterations were noticed in gills such as
aneurism, hyperplasia, degenerated central axis, lifting of gill
epithelium, curved secondary gill lamellae etc. Similarly kidney
showed some detrimental changes like shrunken glomeruli with
increased periglomerular space, degenerated renal tubules etc. Both
haematological and histopathological changes clearly reveal the toxic
potential of RR 120. This work concludes that water pollution
assessment can be done by these two biomarkers which provide
baseline to the further chromosomal or molecular work.
Abstract: Taking into account the significance of measuring the
daily use of the study space in the libraries in order to develop and
reorganize the space for enhancing the efficiency of the study space,
the current study aimed to apply GIS in analyzing the study halls of
the Central Library and Document Center of Tehran University in
order to determine how study desks and chairs were used by the
students. The study used a combination of survey-descriptive and
system design method. In order to gather the required data, surveydescriptive
method was used. For implementing and entering data
into ArcGIS and analyzing the data and displaying the results on the
maps of the study halls of the library, system design method was
utilized. The design of the spatial database of the use of the study
halls was measured through the extent of occupancy of the space by
the library users and the maps of the study halls of the central library
of Tehran University as the case study. The results showed that
Abooreyhan hall had the highest rate of occupancy of the desks and
chairs compared to the other halls. The Hall of Science and
Technology, with an average occupancy rate of 0.39 for the tables
represented the lowest number of users and Rashid al-Dins hall, and
Science and Technology hall with an average occupancy rate (0.40)
had the lowest number of users for seats. In this study, the
comparison of the space occupied at different periods in the morning,
evenings, afternoons, and several months was performed through
GIS. This system analyzed the space relationships effectively and
efficiently. The output of this study would be used by administrators
and librarians to determine the exact extent of use of the equipment
of the study halls and librarians can use the output map to design the
space more efficiently at the library.
Abstract: Nanofibers of PVA /nickel nitrate/silica/alumina
izopropoxide/boric acid composite were prepared by using sol-gel
processing and electrospinning technique. By high temperature
calcinations of the above precursor fibers, nanofibers of
NiO/Al2O3/B2O3/SiO2 composite with diameters about 500 nm
could be successfully obtained. The fibers were characterized by
XRD and SEM analyses.
Abstract: The paper presents an innovative networked radar
system for detection of obstacles in a railway level crossing scenario.
This Monitoring System (MS) is able to detect moving or still
obstacles within the railway level crossing area automatically,
avoiding the need of human presence for surveillance. The MS is also
connected to the National Railway Information and Signaling System
to communicate in real-time the level crossing status. The
architecture is compliant with the highest Safety Integrity Level
(SIL4) of the CENELEC standard. The number of radar sensors used
is configurable at set-up time and depends on how large the level
crossing area can be. At least two sensors are expected and up four
can be used for larger areas. The whole processing chain that
elaborates the output sensor signals, as well as the communication
interface, is fully-digital, was designed in VHDL code and
implemented onto a Xilinx Virtex 6.
Abstract: Employer branding is considered as a useful tool for
addressing the global-local problem facing complex organisations
that have operations scattered across the globe and face challenges of
dealing with the local environment alongside. Despite being an
established field of study within the Western developed world, there
is little empirical evidence concerning the relevance of employer
branding to global companies that operate in the under-developed
economies. This paper fills this gap by gaining rich insight into the
implementation of employer branding programs in a foreign
multinational operating in Pakistan dealing with the global-local
problem. The study is qualitative in nature and employs semistructured
and focus group interviews with senior/middle managers
and local frontline employees to deeply examine the phenomenon in
case organisation. Findings suggest that authenticity is required in
employer brands to enable them to respond to the local needs thereby
leading to the resolution of the global-local problem. However, the
role of signaling theory is key to the development of authentic
employer brands as it stresses on the need to establish an efficient and
effective signaling environment where in signals travel in both
directions (from signal designers to receivers and backwards) and
facilitate firms with the global-local problem. The paper also
identifies future avenues of research for the employer branding field.
Abstract: It is well known that in recent years magnetic
materials have received increased attention due to their properties.
For this reason a significant number of patents that were published
during the last decade are oriented towards synthesis and study of
such materials. The aim of this work is to create and study ferrite
nanocrystalline materials with spinel structure, using sol-gel
technology with participation of auto-combustion. This method is
perspective in that it is a cheap and low-temperature technique that
allows for the fine control on the product’s chemical composition.
Abstract: The biodegradable family of polymers
polyhydroxyalkanoates is an interesting substitute for convectional
fossil-based plastics. However, the manufacturing and environmental
impacts associated with their production via intracellular bacterial
fermentation are strongly dependent on the raw material used and on
energy consumption during the extraction process, limiting their
potential for commercialization. Industrial wastewater is studied in
this paper as a promising alternative feedstock for waste valorization.
Based on results from laboratory and pilot-scale experiments, a
conceptual process design, techno-economic analysis and life cycle
assessment are developed for the large-scale production of the most
common type of polyhydroxyalkanoate, polyhydroxbutyrate.
Intracellular polyhydroxybutyrate is obtained via fermentation of
microbial community present in industrial wastewater and the
downstream processing is based on chemical digestion with
surfactant and hypochlorite. The economic potential and
environmental performance results help identifying bottlenecks and
best opportunities to scale-up the process prior to industrial
implementation. The outcome of this research indicates that the
fermentation of wastewater towards PHB presents advantages
compared to traditional PHAs production from sugars because the
null environmental burdens and financial costs of the raw material in
the bioplastic production process. Nevertheless, process optimization
is still required to compete with the petrochemicals counterparts.
Abstract: In this study, polycaprolactone (PCL) was dissolved
in chloroform:ethanol solvent system at a concentration of 18 w/v %.
1, 2, 4, and 6 droplets of formic acid were added to the prepared 10ml
PCL-chloroform:ethanol solutions separately. Fibrous webs were
produced by electrospinning technique based on the horizontal
working principle. Morphology of the webs was investigated by
using scanning electron microscopy (SEM) whereas fiber diameters
were measured by Image J Software System. The effect of formic
acid addition to the mostly used chloroform solvent on fiber
morphology was examined.
Results indicate that there is a distinct fall in fiber diameter with
the addition of formic acid drops. The average fiber diameter was
measured as 2.22μm in PCL /chloroform:ethanol solution system. On
the other hand, 328nm and 256 nm average fiber diameters were
measured for the samples of 4 drops and 6 drops formic acid added.
This study offers alternative solvent systems to produce nanoscaled,
nontoxic PCL fibrous webs by electrospinning technique.