Abstract: This work presents a comparison between the Annual
Energy Output (AEO) of two commercial vertical-axis wind turbines
(VAWTs) for a low-wind urban site: both a drag-driven and a liftdriven
concepts are examined in order to be installed on top of the
new Via dei Giustinelli building, Trieste (Italy). The power-curves,
taken from the product specification sheets, have been matched to the
wind characteristics of the selected installation site. The influence of
rotor swept area and rated power on the performance of the two
proposed wind turbines have been examined in detail, achieving a
correlation between rotor swept area, electrical generator size and
wind distribution, to be used as a guideline for the calculation of the
AEO.
Abstract: BEAMnrc was used to calculate the spectrum and
HVL for X-ray Beam during low energy X-ray radiation using tube model: SRO 33/100 /ROT 350 Philips. The results of BEAMnrc
simulation and measurements were compared to the IPEM report
number 78 and SpekCalc software. Three energies 127, 103 and 84
Kv were used. In these simulation a tungsten anode with 1.2 mm for
Be window were used as source. HVLs were calculated from
BEAMnrc spectrum with air Kerma method for four different filters.
For BEAMnrc one billion particles were used as original particles for
all simulations. The results show that for 127 kV, there was
maximum 5.2 % difference between BEAMnrc and Measurements
and minimum was 0.7% .the maximum 9.1% difference between
BEAMnrc and IPEM and minimum was 2.3% .The maximum
difference was 3.2% between BEAMnrc and SpekCal and minimum
was 2.8%. The result show BEAMnrc was able to satisfactory predict
the quantities of Low energy Beam as well as high energy X-ray
radiation.
Abstract: When considering the development of constitutive
equations describing the behavior of materials under cyclic plastic
strains, different kinds of formulations can be adopted. The primary
intention of this study is to develop computer programming of
plasticity models to accurately predict the life of engineering
components. For this purpose, the energy or cyclic strain is computed
in multi-surface plasticity models in non-proportional loading and to
present their procedures and codes results.
Abstract: Harmonic pollution and low power factor in power
systems caused by power converters have been of great concern. To
overcome these problems several converter topologies using
advanced semiconductor devices and control schemes have been
proposed. This investigation is to identify a low cost, small size,
efficient and reliable ac to dc converter to meet the input performance
index of UPS. The performance of single phase and three phase ac to
dc converter along with various control techniques are studied and
compared. The half bridge converter topology with linear current
control is identified as most suitable. It is simple, energy efficient
because of single switch power loss and transformer-less operation of
UPS. The results are validated practically using a prototype built
using IGBT and analog controller. The performance for both single
and three-phase system is verified. Digital implementation of closed
loop control achieves higher reliability. Its cost largely depends on
chosen bit precision. The minimal bit precision for optimum
converter performance is identified as 16-bit with fixed-point
operation. From the investigation and practical implementation it is
concluded that half bridge ac – dc converter along with digital linear
controller meets the performance index of UPS for single and three
phase systems.
Abstract: In this paper, we propose a routing scheme that guarantees
the residual lifetime of wireless sensor networks where each
sensor node operates with a limited budget of battery energy. The
scheme maximizes the communications QoS while sustaining the
residual battery lifetime of the network for a specified duration.
Communication paths of wireless nodes are translated into a directed
acyclic graph(DAG) and the maximum-flow algorithm is applied to
the graph. The found maximum flow are assigned to sender nodes, so
as to maximize their communication QoS. Based on assigned flows,
the scheme determines the routing path and the transmission rate of
data packet so that any sensor node on the path would not exhaust
its battery energy before a specified duration.
Abstract: So much energy is used in high rise buildings to fulfill
the basic needs of users such as lighting and thermal comfort.
Malaysia has hot and humid climate, buildings especially high rise
buildings receive unnecessary solar radiation that cause more solar
heat gain. Energy use specially electricity consumption in high rise
buildings has increased. There have been growing concerns about
energy consumption and its effect on environment. Building, energy
and the environment are important issues that the designers should
consider to them. Self protected form is one of possible ways against
the impact of solar radiation in high rise buildings. The Energy
performance of building envelopes was investigated in term of the
Overall Thermal Transfer Value (OTTV ).In this paper, the amount
of OTTV reduction was calculated through OTTV Equations to
clear the effectiveness of self shading strategy on minimizing energy
consumption for cooling interior spaces in high rise buildings which
has considerable envelope areas against solar radiation. Also increasing
the optimum window area was investigated using self-shading
strategy in designing high rise buildings. As result, the significant
reduction in OTTV was shown based on WWR.In addition slight
increase was demonstrated in WWR that can influence on visible
comfort interior spaces.
Abstract: Internal combustion engines rejects 30-40% of the
energy supplied by fuel to the environment through exhaust gas. thus, there is a possibility for further significant improvement of efficiency with the utilization of exhaust gas energy and its conversion to mechanical energy or electrical energy. The Thermo-Electric
Generator (TEG) will be located in the exhaust system and will make use of an energy flow between the warmer exhaust gas and the external environment. Predict to th optimum position of temperature
distribution and the performance of TEG through numerical analysis.
The experimental results obtained show that the power output significantly increases with the temperature difference between cold
and hot sides of a thermoelectric generator.
Abstract: This paper addresses the problem of asymptotic tracking
control of a linear parabolic partial differential equation with indomain
point actuation. As the considered model is a non-standard
partial differential equation, we firstly developed a map that allows
transforming this problem into a standard boundary control problem
to which existing infinite-dimensional system control methods can
be applied. Then, a combination of energy multiplier and differential
flatness methods is used to design an asymptotic tracking controller.
This control scheme consists of stabilizing state-feedback derived
from the energy multiplier method and feed-forward control based
on the flatness property of the system. This approach represents
a systematic procedure to design tracking control laws for a class
of partial differential equations with in-domain point actuation. The
applicability and system performance are assessed by simulation
studies.
Abstract: The aim of this study was to investigate the influence
of reaction temperature and wheat straw moisture content on the
pyrolysis product yields, in the temperature range of 475-575 °C.
Samples of straw with moisture contents from 1.5 wt % to 15.0 wt %
were fed to a bench scale Pyrolysis Centrifuge Reactor (PCR). The
experimental results show that the changes in straw moisture content
have no significant effect on the distribution of pyrolysis product
yields. The maximum bio-oil yields approximately 60 (wt %, on dry
ash free feedstock basis) was observed around 525 °C - 550 °C for all
straw moisture levels. The water content in the wet straw bio-oil was
the highest. The heating value of bio-oil and solid char were
measured and the percentages of its energy distribution were
calculated. The energy distributions of bio-oil, char and gas were 56-
69 % 24-33 %, and 2-19 %, respectively.
Abstract: Acoustic function plays an important role in
aerodynamic mechanical engineering. It can classify the kind of
air-vehicle such as subsonic or supersonic. Acoustic velocity
relates with velocity and Mach number. Mach number relates
again acoustic stability or instability condition. Mach number
plays an important role in growth or decay in energy system.
Acoustic is a function of temperature and temperature is directly
proportional to pressure. If we control the pressure, we can control
acoustic function. To get pressure stability condition, we apply
Navier-Stokes equations.
Abstract: For the sensor network to operate successfully, the active nodes should maintain both sensing coverage and network connectivity. Furthermore, scheduling sleep intervals plays critical role for energy efficiency of wireless sensor networks. Traditional methods for sensor scheduling use either sensing coverage or network connectivity, but rarely both. In this paper, we use random scheduling for sensing coverage and then turn on extra sensor nodes, if necessary, for network connectivity. Simulation results have demonstrated that the number of extra nodes that is on with upper bound of around 9%, is small compared to the total number of deployed sensor nodes. Thus energy consumption for switching on extra sensor node is small.
Abstract: In recent years in Kazakhstan, as well as in all countries, we have been talking not only about the professional stress, but also professional Burnout Syndrome of employees. Burnout is essentially a response to chronic emotional stress – manifests itself in the form of chronic fatigue, despondency, unmotivated aggression, anger, and others. This condition is due to mental fatigue among teachers as a sort of payment for overstrain when professional commitments include the impact of “heat your soul", emotional investment. The emergence of professional Burnout among teachers is due to the system of interrelated and mutually reinforcing factors relating to the various levels of the personality: individually-psychological level is psychodynamic special subject characteristics of valuemotivational sphere and formation of skills and habits of selfregulation; the socio-psychological level includes especially the Organization and interpersonal interaction of a teacher. Signs of the Burnout were observed in 15 testees, and virtually a symptom could be observed in every teacher. As a result of the diagnosis 48% of teachers had the signs of stress (phase syndrome), resulting in a sense of anxiety, mood, heightened emotional susceptibility. The following results have also been got:-the fall of General energy potential – 14 pers. -Psychosomatic and psycho vegetative syndrome – 26 pers. -emotional deficit-34 pers. -emotional Burnout Syndrome-6 pers. The problem of professional Burnout of teachers in the current conditions should become not only meaningful, but particularly relevant. The quality of education of the younger generation depends on professional development; teachers- training level, and how “healthy" teachers are. That is why the systematic maintenance of pedagogic-professional development for teachers (including disclosure of professional Burnout Syndrome factors) takes on a special meaning.
Abstract: Aluminum/Copper clad sheet has been fabricated using
asymmetric extrusion method, which caused severe shear deformation
between Al and Cu plate to easily bond to each other. Interfacial
microstructure and mechanical properties of Al/Cu clad were studied
by scanning electron microscope equipped with energy dispersive
X-ray detector, micro-hardness, and tension tests. The asymmetric
extrusion bonding was very effective to provide a good interface for
atoms diffusion during subsequent annealing. The strength of bonding
was higher with the increasing extrusion ratio.
Abstract: Transportation is one of the most fundamental
challenges of urban development in contemporary world. On the
other hand, sustainable urban development has received tremendous
public attention in the last few years. This trend in addition to other
factors such as energy cost, environmental concerns, traffic
congestion and the feeling of lack of belonging have contributed to
the development of pedestrian areas. The purpose of this paper is to
study the role of walkable streets in sustainable development of
cities. Accordingly, a documentary research through valid sources
has been utilized to substantiate this study. The findings demonstrate
that walking can lead to sustainable urban development from
physical, social, environmental, cultural, economic and political
aspects. Also, pedestrian areas –which are the main context of
walking- act as focal points of development in cities and have a great
effect on modifying and stimulating of their adjacent urban spaces.
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: As the information age matures, major social
infrastructures such as communication, finance, military and energy,
have become ever more dependent on information communication
systems. And since these infrastructures are connected to the Internet,
electronic intrusions such as hacking and viruses have become a new
security threat. Especially, disturbance or neutralization of a major
social infrastructure can result in extensive material damage and social
disorder. To address this issue, many nations around the world are
researching and developing various techniques and information
security policies as a government-wide effort to protect their
infrastructures from newly emerging threats. This paper proposes an
evaluation method for information security levels of CIIP (Critical
Information Infrastructure Protection), which can enhance the security
level of critical information infrastructure by checking the current
security status and establish security measures accordingly to protect
infrastructures effectively.
Abstract: A process flowsheet was developed in ChemCad 6.4
to study the effect of feed moisture contents on the pre-esterification
of waste oils. Waste oils were modelled as a mixture of triolein
(90%), oleic acid (5%) and water (5%). The process mainly consisted
of feed drying, pre-esterification reaction and methanol recovery. The
results showed that the process energy requirements would be
minimized when higher degrees of feed drying and higher preesterification
reaction temperatures are used.
Abstract: MiRNAs participate in gene regulation of translation.
Some studies have investigated the interactions between genes and
intragenic miRNAs. It is important to study the miRNA binding sites
of genes involved in carcinogenesis. RNAHybrid 2.1 and ERNAhybrid
programmes were used to compute the hybridization free
energy of miRNA binding sites. Of these 54 mRNAs, 22.6%, 37.7%,
and 39.7% of miRNA binding sites were present in the 5'UTRs,
CDSs, and 3'UTRs, respectively. The density of the binding sites for
miRNAs in the 5'UTR ranged from 1.6 to 43.2 times and from 1.8 to
8.0 times greater than in the CDS and 3'UTR, respectively. Three
types of miRNA interactions with mRNAs have been revealed: 5'-
dominant canonical, 3'-compensatory, and complementary binding
sites. MiRNAs regulate gene expression, and information on the
interactions between miRNAs and mRNAs could be useful in
molecular medicine. We recommend that newly described sites
undergo validation by experimental investigation.
Abstract: Fossil fuels are the major source to meet the world
energy requirements but its rapidly diminishing rate and adverse
effects on our ecological system are of major concern. Renewable
energy utilization is the need of time to meet the future challenges.
Ocean energy is the one of these promising energy resources. Threefourths
of the earth-s surface is covered by the oceans. This enormous
energy resource is contained in the oceans- waters, the air above the
oceans, and the land beneath them. The renewable energy source of
ocean mainly is contained in waves, ocean current and offshore solar
energy. Very fewer efforts have been made to harness this reliable
and predictable resource. Harnessing of ocean energy needs detail
knowledge of underlying mathematical governing equation and their
analysis. With the advent of extra ordinary computational resources
it is now possible to predict the wave climatology in lab simulation.
Several techniques have been developed mostly stem from numerical
analysis of Navier Stokes equations. This paper presents a brief over
view of such mathematical model and tools to understand and
analyze the wave climatology. Models of 1st, 2nd and 3rd generations
have been developed to estimate the wave characteristics to assess the
power potential. A brief overview of available wave energy
technologies is also given. A novel concept of on-shore wave energy
extraction method is also presented at the end. The concept is based
upon total energy conservation, where energy of wave is transferred
to the flexible converter to increase its kinetic energy. Squeezing
action by the external pressure on the converter body results in
increase velocities at discharge section. High velocity head then can
be used for energy storage or for direct utility of power generation.
This converter utilizes the both potential and kinetic energy of the
waves and designed for on-shore or near-shore application. Increased
wave height at the shore due to shoaling effects increases the
potential energy of the waves which is converted to renewable
energy. This approach will result in economic wave energy
converter due to near shore installation and more dense waves due to
shoaling. Method will be more efficient because of tapping both
potential and kinetic energy of the waves.
Abstract: Three dimensional nanostructure materials have attracted the attention of many researches because the possibility to apply them for near future devices in sensors, catalysis and energy related. Tin dioxide is the most used material for gas sensing because its three-dimensional nanostructures and properties are related to the large surface exposed to gas adsorption. We propose the use of branch SnO2 nanowhiskers in interaction with ethanol. All Sn atoms are symmetric. The total energy, potential energy and Kinetic energy calculated for interaction between SnO2 and ethanol in different distances and temperatures. The calculations achieved by methods of Langevin Dynamic and Mont Carlo simulation. The total energy increased with addition ethanol molecules and temperature so interactions between them are endothermic.