Abstract: Knowing about the customer behavior in a grocery has
been a long-standing issue in the retailing industry. The advent of
RFID has made it easier to collect moving data for an individual
shopper's behavior. Most of the previous studies used the traditional
statistical clustering technique to find the major characteristics of
customer behavior, especially shopping path. However, in using the
clustering technique, due to various spatial constraints in the store,
standard clustering methods are not feasible because moving data such
as the shopping path should be adjusted in advance of the analysis,
which is time-consuming and causes data distortion. To alleviate this
problem, we propose a new approach to spatial pattern clustering
based on the longest common subsequence. Experimental results using
real data obtained from a grocery confirm the good performance of the
proposed method in finding the hot spot, dead spot and major path
patterns of customer movements.
Abstract: Gas Metal Arc Welding (GMAW) processes is an
important joining process widely used in metal fabrication
industries. This paper addresses modeling and optimization of this
technique using a set of experimental data and regression analysis.
The set of experimental data has been used to assess the influence
of GMAW process parameters in weld bead geometry. The
process variables considered here include voltage (V); wire feed
rate (F); torch Angle (A); welding speed (S) and nozzle-to-plate
distance (D). The process output characteristics include weld bead
height, width and penetration. The Taguchi method and regression
modeling are used in order to establish the relationships between
input and output parameters. The adequacy of the model is
evaluated using analysis of variance (ANOVA) technique. In the
next stage, the proposed model is embedded into a Simulated
Annealing (SA) algorithm to optimize the GMAW process
parameters. The objective is to determine a suitable set of process
parameters that can produce desired bead geometry, considering
the ranges of the process parameters. Computational results prove
the effectiveness of the proposed model and optimization
procedure.
Abstract: It has often been said that the strength of any country
resides in the strength of its industrial sector, and Progress in
industrial society has been accomplished by the creation of new
technologies. Developments have been facilitated by the increasing
availability of advanced manufacturing technology (AMT), in
addition the implementation of advanced manufacturing technology
(AMT) requires careful planning at all levels of the organization to
ensure that the implementation will achieve the intended goals.
Justification and implementation of advanced manufacturing
technology (AMT) involves decisions that are crucial for the
practitioners regarding the survival of business in the present days of
uncertain manufacturing world. This paper assists the industrial
managers to consider all the important criteria for success AMT
implementation, when purchasing new technology. Concurrently,
this paper classifies the tangible benefits of a technology that are
evaluated by addressing both cost and time dimensions, and the
intangible benefits are evaluated by addressing technological,
strategic, social and human issues to identify and create awareness of
the essential elements in the AMT implementation process and
identify the necessary actions before implementing AMT.
Abstract: The interactions between input/output variables are a very common phenomenon encountered in the design of multi-loop controllers for interacting multivariable processes, which can be a serious obstacle for achieving a good overall performance of multiloop control system. To overcome this impediment, the decomposed dynamic interaction analysis is proposed by decomposing the multiloop control system into a set of n independent SISO systems with the corresponding effective open-loop transfer function (EOTF) within the dynamic interactions embedded explicitly. For each EOTF, the reduced model is independently formulated by using the proposed reduction design strategy, and then the paired multi-loop proportional-integral-derivative (PID) controller is derived quite simply and straightforwardly by using internal model control (IMC) theory. This design method can easily be implemented for various industrial processes because of its effectiveness. Several case studies are considered to demonstrate the superior of the proposed method.
Abstract: Requirement engineering has been the subject of large
volume of researches due to the significant role it plays in the
software development life cycle. However, dynamicity of software
industry is much faster than advances in requirements engineering
approaches. Therefore, this paper aims to systematically review and
evaluate the current research in requirement engineering and identify
new research trends and direction in this field. In addition, various
research methods associated with the Evaluation-based techniques
and empirical study are highlighted for the requirements engineering
field. Finally, challenges and recommendations on future directions
research are presented based on the research team observations
during this study.
Abstract: Study of fire and explosion is very important mainly
in oil and gas industries due to several accidents which have been
reported in the past and present. In this work, we have investigated
the flammability of bio oil vapour mixtures. This mixture may
contribute to fire during the storage and transportation process. Bio
oil sample derived from Palm Kernell shell was analysed using Gas
Chromatography Mass Spectrometry (GC-MS) to examine the
composition of the sample. Mole fractions of 12 selected
components in the liquid phase were obtained from the GC-FID data
and used to calculate mole fractions of components in the gas phase
via modified Raoult-s law. Lower Flammability Limits (LFLs) and
Upper Flammability Limits (UFLs) for individual components were
obtained from published literature. However, stoichiometric
concentration method was used to calculate the flammability limits
of some components which their flammability limit values are not
available in the literature. The LFL and UFL values for the mixture
were calculated using the Le Chatelier equation. The LFLmix and
UFLmix values were used to construct a flammability diagram and
subsequently used to determine the flammability of the mixture. The
findings of this study can be used to propose suitable inherently
safer method to prevent the flammable mixture from occurring and
to minimizing the loss of properties, business, and life due to fire
accidents in bio oil productions.
Abstract: Semisolid metal processing uses solid–liquid slurries
containing fine and globular solid particles uniformly distributed in a
liquid matrix, which can be handled as a solid and flow like a liquid.
In the recent years, many methods have been introduced for the
production of semisolid slurries since it is scientifically sound and
industrially viable with such preferred microstructures called
thixotropic microstructures as feedstock materials. One such process
that needs very low equipment investment and running costs is the
cooling slope. In this research by using a mechanical stirrer slurry
maker constructed by the authors, the effects of mechanical stirring
parameters such as: stirring time, stirring temperature and stirring
Speed on micro-structure and mechanical properties of A360
aluminum alloy in semi-solid forming, are investigated. It is
determined that mold temperature and holding time of part in
temperature of 580ºC have a great effect on micro-structure and
mechanical properties(stirring temperature of 585ºC, stirring time of
20 minutes and stirring speed of 425 RPM). By optimizing the
forming parameters, dendrite microstructure changes to globular and
mechanical properties improves. This is because of breaking and
globularzing dendrites of primary α-AL.
Abstract: Currently, there are many local area industrial networks
that can give guaranteed bandwidth to synchronous traffic, particularly
providing CBR channels (Constant Bit Rate), which allow
improved bandwidth management. Some of such networks operate
over Ethernet, delivering channels with enough capacity, specially
with compressors, to integrate multimedia traffic in industrial monitoring
and image processing applications with many sources. In
these industrial environments where a low latency is an essential
requirement, JPEG is an adequate compressing technique but it
generates VBR traffic (Variable Bit Rate). Transmitting VBR traffic
in CBR channels is inefficient and current solutions to this problem
significantly increase the latency or further degrade the quality. In
this paper an R(q) model is used which allows on-line calculation of
the JPEG quantification factor. We obtained increased quality, a lower
requirement for the CBR channel with reduced number of discarded
frames along with better use of the channel bandwidth.
Abstract: The equilibrium chemical reactions taken place in a converter reactor of the Khorasan Petrochemical Ammonia plant was studied using the minimization of Gibbs free energy method. In the minimization of the Gibbs free energy function the Davidon– Fletcher–Powell (DFP) optimization procedure using the penalty terms in the well-defined objective function was used. It should be noted that in the DFP procedure along with the corresponding penalty terms the Hessian matrices for the composition of constituents in the Converter reactor can be excluded. This, in fact, can be considered as the main advantage of the DFP optimization procedure. Also the effect of temperature and pressure on the equilibrium composition of the constituents was investigated. The results obtained in this work were compared with the data collected from the converter reactor of the Khorasan Petrochemical Ammonia plant. It was concluded that the results obtained from the method used in this work are in good agreement with the industrial data. Notably, the algorithm developed in this work, in spite of its simplicity, takes the advantage of short computation and convergence time.
Abstract: This paper analyzed the perception of e-commerce
application services by construction material traders in Malaysia.
Five attributes were tested: usability, reputation, trust, privacy and
familiarity. Study methodology consists of survey questionnaire and
statistical analysis that includes reliability analysis, factor analysis,
ANOVA and regression analysis. The respondents were construction
material traders, including hardware stores in Klang Valley, Kuala
Lumpur.
Findings support that usability and familiarity with e-commerce
services in Malaysia have insignificant influence on the acceptance of
e-commerce application. However, reputation, trust and privacy
attributes have significant influence on the choice of e-commerce
acceptance by construction material traders. E-commerce
applications studied included customer database, e-selling, emarketing,
e-payment, e-buying and online advertising. Assumptions
are made that traders have basic knowledge and exposure to ICT
services. i.e. internet service and computers. Study concludes that
reputation, privacy and trust are the three website attributes that
influence the acceptance of e-commerce by construction material
traders.
Abstract: Swedish truck industry is investigating the possibility
for implementing the use of Compacted Graphite Iron (CGI) in their
heavy duty diesel engines. Compared to the alloyed gray iron used
today, CGI has superior mechanical properties but not as good
machinability. Another issue that needs to be addressed when
implementing CGI is the inhomogeneous microstructure when the
cast component has different section thicknesses, as in cylinder
blocks. Thinner sections results in finer pearlite, in the material, with
higher strength. Therefore an investigation on its influence on
machinability was needed. This paper focuses on the effect that
interlamellar distance in pearlite has on CGI machinability and
material physical properties. The effect of pearlite content and
nodularity is also examined. The results showed that interlamellar
distance in pearlite did not have as large effect on the material
physical properties or machinability as pearlite content. The paper
also shows the difficulties of obtaining a homogeneous
microstructure in inhomogeneous workpieces.
Abstract: The pulp and paper mill effluent is one of the high
polluting effluent amongst the effluents obtained from polluting
industries. All the available methods for treatment of pulp and paper
mill effluent have certain drawbacks. The coagulation is one of the
cheapest process for treatment of various organic effluents. Thus, the
removal of chemical oxygen demand (COD) and colour of paper mill
effluent is studied using coagulation process. The batch coagulation
process was performed using various coagulants like: aluminium
chloride, poly aluminium chloride and copper sulphate. The initial
pH of the effluent (Coagulation pH) has tremendous effect on COD
and colour removal. Poly aluminium chloride (PAC) as coagulant
reduced COD to 84 % and 92 % of colour was removed at an
optimum pH 5 and coagulant dose of 8 ml l-1. With aluminium
chloride at an optimum pH = 4 and coagulant dose of 5 g l-1, 74 %
COD and 86 % colour removal were observed. The results using
copper sulphate as coagulant (a less commercial coagulant) were
encouraging. At an optimum pH 6 and mass loading of 5 g l-1, 76 %
COD reduction and 78 % colour reduction were obtained. It was also
observed that after addition of coagulant, the pH of the effluent
decreases. The decrease in pH was highest for AlCl3, which was
followed by PAC and CuSO4. Significant amount of COD reductions
was obtained by coagulation process. Since the coagulation process
is the first stage for treatment of effluent and some of the coagulant
cations usually remain in the treated effluents. Thus, cation like
copper may be one of the good catalyst for second stage of treatment
process like wet oxidation. The copper has been found to be good
oxidation catalyst then iron and aluminum.
Abstract: Through the course of this paper we outline how
mobile Business Intelligence (m-BI) can help businesses to work
smarter and to improve their agility. When we analyze the industry
from the usage perspective or how interaction with the enterprise BI
system happens via mobile devices, we may easily understand that
there are two major types of mobile BI: passive and active. Active
mobile BI gives provisions for users to interact with the BI systems
on-the-fly. Active mobile business intelligence often works as a
combination of both “push and pull" techniques. Some mistakes were
done in the up-to-day progress of mobile technologies and mobile BI,
as well as some problems that still have to be resolved. We discussed
in the paper rather broadly.
Abstract: International competitiveness receives much attention
nowadays, but up to now its assessment has been heavily based on
manufacturing industry statistics. This paper addresses the need for
competitiveness indicators that cover the service sector and sets out a
multilevel framework for measuring international services trade
competitiveness. The approach undertaken here aims at
comparatively examining the international competitiveness of the
EU-25 (the twenty-five European Union member states before the 1st
of January 2007), Romanian and Bulgarian services trade, as well as
the last two countries- structure of specialization on the EU-25
services market. The primary changes in the international
competitiveness of three major services sectors – transportation,
travel and other services - are analyzed. This research attempts to
determine the ability of the two recent European Union (EU) member
states to contend with the challenges that might arise from the hard
competition within the enlarged EU, in the field of services trade.
Abstract: The paper suggests for the first time the use of dynamic programming techniques for optimal risk reduction in the railway industry. It is shown that by using the concept ‘amount of removed risk by a risk reduction option’, the problem related to optimal allocation of a fixed budget to achieve a maximum risk reduction in the railway industry can be reduced to an optimisation problem from dynamic programming. For n risk reduction options and size of the available risk reduction budget B (expressed as integer number), the worst-case running time of the proposed algorithm is O (n x (B+1)), which makes the proposed method a very efficient tool
for solving the optimal risk reduction problem in the railway industry.
Abstract: Waste problem is becoming a future problem all over the world. Magnesium wastes which can be used in recycling processes are produced by many industrial activities. Magnesium borates which have useful properties such as; high heat resistance, corrosion resistance, supermechanical strength, superinsulation, light weight, high coefficient of elasticity and so on. Addition, magnesium borates have great potential in the development of ceramic and detergents industry, whisker-reinforced composites, antiwear, and reducing friction additives.
In this study, using the starting materials of waste magnesium and H3BO3 the hydrothermal method was applied at a moderate temperature of 70oC with different reaction times. Several reaction times of waste magnesium to H3BO3 were selected as; 30, 60, 120, 240 minutes. After the synthesis, X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR) techniques were applied to products. As a result, the forms of Admontite [MgO(B2O3)3.7(H2O)] and Mcallisterite [Mg2(B6O7(OH)6)2.9(H2O)] were synthesized.
Abstract: This paper presents the system identification by
physical-s law method and designs the controller for the Azimuth
Angle Control of the Platform of the Multi-Launcher Rocket System
(MLRS) by Root Locus technique. The plant mathematical model
was approximated using MATLAB for simulation and analyze the
system. The controller proposes the implementation of PID
Controller using Programmable Logic Control (PLC) for control the
plant. PID Controllers are widely applicable in industrial sectors and
can be set up easily and operate optimally for enhanced productivity,
improved quality and reduce maintenance requirement. The results
from simulation and experiments show that the proposed a PID
Controller to control the elevation angle that has superior control
performance by the setting time less than 12 sec, the rise time less
than 1.6 sec., and zero steady state. Furthermore, the system has a
high over shoot that will be continue development.
Abstract: In the last decade, carbohydrates have attracted great
attention as renewable resources for the chemical industry.
Carbohydrates are abundantly found in nature in the form of
monomers, oligomers and polymers, or as components of
biopolymers and other naturally occurring substances. As natural
products, they play important roles in conferring certain physical,
chemical, and biological properties to their carrier molecules.The
synthesis of this particular carbohydrate glycomonomer is part of our
work to obtain biodegradable polymers. Our current paper describes
the synthesis and characterization of a novel carbohydrate
glycomonomer starting from D-glucose, in several synthesis steps,
that involve the protection/deprotection of the D-glucose ring via
acetylation, tritylation, then selective deprotection of the aromaticaliphatic
protective group, in order to obtain 1,2,3,4-tetra-O-acetyl-
6-O-allyl-β-D-glucopyranose. The glycomonomer was then obtained
by the allylation in drastic conditions of 1,2,3,4-tetra-O-acetyl-6-Oallyl-
β-D-glucopyranose with allylic alcohol in the presence of
stannic chloride, in methylene chloride, at room temperature. The
proposed structure of the glycomonomer, 2,3,4-tri-O-acetyl-1,6-di-
O-allyl-β-D-glucopyranose, was confirmed by FTIR, NMR and
HPLC-MS spectrometry. This glycomonomer will be further
submitted to copolymerization with certain acrylic or methacrylic
monomers in order to obtain competitive plastic materials for
applications in the biomedical field.
Abstract: This study deals with a multi-criteria optimization
problem which has been transformed into a single objective
optimization problem using Response Surface Methodology (RSM),
Artificial Neural Network (ANN) and Grey Relational Analyses
(GRA) approach. Grey-RSM and Grey-ANN are hybrid techniques
which can be used for solving multi-criteria optimization problem.
There have been two main purposes of this research as follows.
1. To determine optimum and robust fiber dyeing process
conditions by using RSM and ANN based on GRA,
2. To obtain the best suitable model by comparing models
developed by different methodologies.
The design variables for fiber dyeing process in textile are
temperature, time, softener, anti-static, material quantity, pH,
retarder, and dispergator. The quality characteristics to be evaluated
are nominal color consistency of fiber, maximum strength of fiber,
minimum color of dyeing solution. GRA-RSM with exact level
value, GRA-RSM with interval level value and GRA-ANN models
were compared based on GRA output value and MSE (Mean Square
Error) performance measurement of outputs with each other. As a
result, GRA-ANN with interval value model seems to be suitable
reducing the variation of dyeing process for GRA output value of the
model.
Abstract: In this paper, a simple microfluidic device for monitoring algal cell behavior is proposed. An array of algal microwells is fabricated by PDMS soft-lithography using X-ray LIGA mold, placed on a glass substrate. Two layers of replicated PDMS and substrate are attached by oxygen plasma bonding, creating a microchannel for the microfluidic system. Algal cell are loaded into the microfluidic device, which provides positive charge on the bottom surface of wells. Algal cells, which are negative charged, can be attracted to the bottom of the wells via electrostatic interaction. By varying the concentration of algal cells in the loading suspension, it is possible to obtain wells with a single cell. Liquid medium for cells monitoring are flown continuously over the wells, providing nutrient and waste exchange between the well and the main flow. This device could lead to the uncovering of the quantitative biology of the algae, which is a key to effective and extensive algal utilizations in the field of biotechnology, food industry and bioenergy research and developments.